Search Documents

By Z. Zhang, Cuihuan Huang, Zongshu Zou, Nan Wang, Xueqian Xin

"Vitrification is considered as an attractive procedure for municipal solid waste incineration ash, which can realize the volume reduction and innocent treatment of incineration ash, as well as reuse of bottom ash. The main oxide components of molten ash slag are CaO, Al2O3, SiO2, Fe2O3, MgO, and Na2O, accounting for more than 90% of the total mass. The phase relations and thermodynamic properties of the CaO-Al2O3-SiO2-FeOx-MgO-Na2O oxide system is highly required, and is of great scientific significance for optimization of vitrification processing and sustainable resource utilization of melting slag. A study on the equilibria phase relations of CaO-SiO2-MgO-FeOx system was done by using CALPHAD method based on FactSage in this paper. The modeling parameters for the thermodynamic properties of liquid phase in CaO-SiO2-MgO-FeOx system were established and the equilibrium phase relations of MgO-SiO2-FeOx and CaO-SiO2-FeOx-MgO systems were calculated for different temperatures and oxygen partial pressures.IntroductionThe main oxide components of vitrified bottom ash slag are CaO, Al2O3, SiO2, Fe2O3, MgO, and Na2O, accounting for more than 90% of the bottom ash by weight [1]. During slag processing and modification, the knowledge of thermodynamic properties and liquidus temperature in the related slag system is highly required [2-5], which is not yet available. Through literature survey [6-9], it is clear that the systematic information on the concerned complex slag system is scarce. Most binary subsystems except FeOx-Na2O have been investigated well. Among ternary subsystems, few phase relations of the Na2O-MgO-SiO2 ternary system are available. For the phase relations of the system Na2O-MgO-Al2O3, all the studies are focused on the Al2O3-rich region. Investigation on the CaO-Al2O3-FeOx system is limited to Fe2O3-containing system with relatively higher oxygen potential. Most quaternary systems are not studied well except the CaO-MgO-Al2O3-SiO2 system, mainly due to their metallurgical importance. Figure 1 demonstrates the research status of the vitrified bottom ash slag with almost zero effort [10]. The effort here is defined based on the published literature by considering the number of publications, the investigated composition ranges, and the research details. So far the engineers in the field have to make assumptions of the thermodynamic properties of the simplified oxide system, without taking into consideration the interactions of the different oxide components, which hinders the development of the slag valorization and utilization. In order to provide thermodynamic properties for the application of the vitrified bottom ash, the six-component oxide system (CaO-MgO-Al2O3-SiO2-FeOx-Na2O) will be investigated through both experimental approach and computer modeling."

Jan 1, 2011

By T. A. Sullivan

Refining in a molten salt electrolyte was investigated as a means of recovering nickel containing less than 1 percent and preferably less than 0.2 percent cobalt from nickel products containing up to 5 percent cobalt. Electrolytic separation of nick and cobalt was accomplished in a molten KCl-LiCl-NiCl2 electrolyte. Nickel containing less than 0.10 percent cobalt was routinely prepared. Factors that influenced the transfer of cobalt to the refined product were the nickel concentration of the electrolyte, the cobalt concentration of the electrolyte, the ratio of nickel to cobalt in the electrolyte, and cathode current densities. A method of recovering the cobalt from the electrolyte was developed. The possibility of preparing high-purity nickel by this process was shown, as well as the preparation of various cobalt-nickel-tungsten alloys.

Jan 1, 1968

THE following employment items are made available to AIME members on a non-profit basis by the Engineering Societies Personnel Service, Inc., operating in cooperation with the Four Founder Societies. Local offices of the Personnel Service are at 8 W. 40th.St. New York 18; 100 Farnsworth Ave., Detroit; 57. Post St., San Francisco; 84 E. Randolph St., Chicago 1. Applicants should address all mail to' the proper key numbers in care of the New York office and include 6c in stamps for forwarding and. returning application. The applicant agrees, if placed in a position by means of the Service, to pay the placement fee listed by the Service. AIME members may secure a weekly bulletin of positions available for $3.50 a quarter, $12 a year. MEN AVAILABLE Mining Engineer, 41, married, one child, employed. Broad experience, both underground and open-pit, type mining. Exploration, development, exploitation, industrial construction, milling in northwestern United States. Desires position with progressive, established concern. M-666-259¬Chicago. Recent Graduate, 24, married, no children, B.S. mineral economics. Employed-one year's experience in development of deposits, study of problem areas. Will accept position anywhere in the world. Available immediately. M-667.

Jan 1, 1952

By Lesley Andrews

"Electron microbeam analysis of metallurgical samples covers a broad field and has applications in the areas of minerals processing, hydrometallurgy, pyrometallurgy, physical metallurgy and corrosion.Some idea of the possibilities of microbeam techniques can be illustrated by examining the following example of a run of mine gold ore sample. Milling and bulk chemical analysis of the ore will provide major and minor element analysis as well as the gold grade. More detailed chemistlY can also reveal the presence of trace elements that may be advantageous or deleterious to downstream processing. Electron microbeam analysis can provide additional information in the form of - size, liberation, association and composition of the gold, the percentage of refractory gold, the size, liberation, association and composition of enclosing sulphide or arsenide phases and the levels and association of the trace elements that may affect processing. In most cases electron microbeam analysis compliments bulk chemistry, and does not replace it. Both techniques should be used in parallel for maximum effect.This paper touches on the origin and history of electron microbeam techniques, as well as the theory behind microbeam analysis and processing. The more common types of instruments and their applications will also be dealt with briefly - more details on, and examples of, the applications and choice of technique will be covered in the presentation.Mosely first discovered, in 1913, that the frequency of emitted X-radiation excited by an electron beam is a function of the atomic number of the analysed element. This discovery led to the development of spectrochemical analysis. The forerunners of the electron microanalysers of today, however, were only invented during the nineteen fifties. The electron microprobe was developed in parallel by Castaing and Guinier in France and by Borovski in Russia, but Castaing's design was the basis of modern microanalysers. The initial area of analysis was brought down from over 1 mm2 to less than 2 µm, as it is today. In 1956 Cosslett and Duncumb invented the scanning electron microprobe, where a beam of electrons could be scanned across an area of a sample. This, in turn, led to the development of the electron microprobe with both scanning and point analysis capabilities that we know today.Essentially, all electron microbeam instruments operate by the production of a beam of electrons from a filament in a vacuum (i.e. an electron gun). The electron beam leaves the gun and is accelerated and focused by a series of electromagnetic lenses while passing down an evacuated column. The electrons eventually strike the surface of the sample to be analysed and may travel through a thin sample (transmitted electron microscopy) or react with a thicker sample to produce several reflected kinds of radiation."

Jan 1, 2014

By Desmond Y. M. Lee

This paper presents a procedure to prepare input for the computerized pit design system at Iron Ore Company of Canada. The procedure is simple and requires very little training. Also, it is general enough to accept both bench (horizontal cross section) maps and section (vertical cross section) maps. The output of this procedure is data which represent blocks of ore and waste with dollar values based on mineral content. The ultimate pit design is presented in printer-generated graphs, with numbers indicating the depths of pit bottom walls. Roads are added manually by the engineer with the aid of other computer programs. Section maps and bench maps are also printed as part of the output of the ultimate pit design.

Jan 1, 1978

By M. C. Pietrobon

"A common problem in assessing the applicability of laboratory flotation data is determining how closely conditions during laboratory testing of the ore matches those that occur in a plant. Typical laboratory based investigations do not consider factors such as water quality, pulp temperature and the pulp chemical environment during both grinding and conditioning on laboratory flotation performance. Disregarding these important factors may seriously compromise the validity of conclusions based solely on laboratory experimental results. Furthermore, considering these factors during the flowsheet design stage in the development of new ore resources may reduce financial risk associated with building a new plant. A methodology is described here which embraces these factors in an attempt to bridge the gap between laboratory and plant. The methodology should be considered a vital first step in all laboratory based experimental programs and has implications for fundamental studies on the flotation behaviour of single minerals. This methodology increases the confidence with which findings of laboratory based studies can be transferred to the plant and highlights the effect of variables which may be accessible to manipulation in the plant.Pulp chemical parameters, such as pulp dissolved oxygen demand, pH, Eh, mineral oxidation and solution composition were manipulated in the laboratory by adjusting the duration of gas purging after grinding, the process water input and pulp temperature. A key finding was that matching of the laboratory pulp chemistry to the plant pulp chemistry was dependent upon oxidation after grinding. In turn, mineral oxidation was dependent upon the pH in grinding, water composition and the duration of oxygen purging after grinding. The methodology closely matched the dissolved oxygen demand and surface chemistry of laboratory and plant pulps."

Jan 1, 2002

By Sachihiko Tokunaga, Hirofumi Taguchi, Kenji Maruyama, Hidenori Takahashi, Yoshiyuki Morikawa

"Abstract The present study proposed a new liquefaction countermeasure to improve sandy ground and conducted a trial execution. The new method is a floating-type and lattice-shaped cement treatment method, where cement-treated soil is not fixed to a non-liquefiable stratum. A fixed structure such as treated soil should be formed at the side of the floating-type treated soil to reduce its lateral displacement. In the study, one-dimensional dynamic response analyses were first conducted to confirm the mechanism of the new method. Then, a series of centrifuge model tests were performed to demonstrate the effect under a stress condition at the prototype scale. The analyses and model tests confirmed the effect of the liquefaction countermeasure. Finally, trial executions were carried out to confirm high-quality vertical execution.INTRODUCTIONLiquefaction induced by an earthquake generates sand boiling and ground settlement. Other problems have also been reported, including a decrease in bearing capacity and an increase in the horizontal earth pressure against retaining walls. To prevent these problems caused by liquefaction of the ground, various countermeasures have been proposed, such as cement deep mixing and high-pressure jet mixing methods. These methods have the big advantage of being applicable to ground that contains soil with a fine-grain fraction. Furthermore, the unnecessary displacement caused by the construction can be reduced. In Japan, a lattice-shaped cement-treatment method has frequently been used at many construction sites to prevent liquefaction, where cement-treated piles are intersected to form a lattice, as shown in Fig. 1. The lattice-shaped walls can reduce the shear stress generated by an earthquake, restricting the liquefaction at that location. However, the construction cost of the cement treatment is relatively high compared to other methods such as the sand compaction pile (SCP) method, and needs to be reduced. In particular, the cost of the high-pressure jet mixing method, which can be applied to the liquefiable ground under existing structures, is significantly high. Therefore, decreasing the total volume of the cement treatment is necessary to reduce the construction cost."

Jan 1, 2014

By R. D. Stewart

Paper presented at the conference: Risk assessment in the extractive industries, held in Exeter, UK, 23-24 March 1994, and first published London: IMM, 1994, preprint volume, 18pp., 5 refs. A seismic risk assessment method has been developed for application to rockburst prone deep-level mining sites which have sufficient seismic coverage. The technique utilises several seismic hazard parameters simultaneously and assesses the seismic risk on a daily basis according to the individual levels of these parameters. Critical levels are determined from investigation of the long-term behaviour of the parameters in relation to recorded potentially damaging seismic events. The method has been applied to a data set comprising 15 months' worth of seismic data, with encouraging results

Aug 1, 1995

By M. Nilmani, J. Sofra

The transverse distributions of the solids discharge velocity and mass flux at the discharge end of vertical and inclined lances were measured in order to detennine the transverse distributions of the axial momentum flux, which is a dominant factor influencing the penetration behaviour of particles into melts during submerged injection. The effects of gas velocity (10 - 30 m/s), solids loading (5 - 10), lance length (0.15 - 1.0 m), lance inclination (vertical downward - horizontal) and particle density (2500 - 8900 kg/m3 ) were investigated, while the lance diameter and particle size were fixed at 10 mm and 220 µm respectively. The particle velocities and mass fluxes were measured by image analysis of particles illuminated in a laser-generated light sheet aligned vertically through the axis of the lance at the discharge point. The particle discharge velocity profiles for vertical downward flows were synunetrical about the centre-line of the lance, with the maximum velocities occurring at the centre-line. The velocities increased with increasing gas velocity, increasing lance length and decreasing particle density in accordance with previous observations. The transverse mass flux profiles were also synunetrical for vertical downward flows, however at the lower gas velocities the peaks in the profiles were displaced from the centre-line of the lance by a fractional diameter of about 0.15. The particle discharge velocity profiles become increasingly asynunetric as the lance orientation was changed from vertical to horizontal, with higher particle velocities present near the top wall of the lance. The mass flux profile also became asyrrunetric as the horizontal orientation was approached, however in this case, the profile became biased towards the bottom of the lance. The effect was much more pronounced for a gas velocity of 10 m/s than for 30 m/s, showing the relatively stronger gravitational influence as the velocity was reduced.

Jan 1, 1996

Early in 1940 the development and sampling programmes in hand on the North and British Sections of North Broken Hill Limited were such as to necessitate the drilling of a large number of drill holes ranging up to about thirty feet in length. On the British Section, one purpose was to test the existence, width, and value of narrow lodes believed, for geological reasons, to occur in the walls of the existing workings. Another object was to definitely disprove the existence of payable shoots of ore in certain largerhodonite and quartz-garnet ("garnet sandstone") pillars which had been formerly left as unpayable.On the North Section, the main purpose of the short holes was to delineate the ore-body boundaries by drilling laterally from drives in ore, and thus enable level layout to be planned in advance of sill stoping. It was also desired to test the walls of stopes in those portions of the mine where the economic limit of mining is not rendered obvious by a clear-cut wall, but should be determined by assay. In these latter cases it was hoped to eliminate "prospecting by stoping," a procedure by which any doubts as to the existence of further good ore behind the low-grade walls were settled by continuing to stope laterally until all chance of such an occurrence was removed.LONG HOLE ROCK DRILLINGFollowing an investigation of recorded instances of similar practice elsewhere it was decided to use the rock drill for a series of trial sample holes. A 3-in. drifter was used. This was selected from those in use underground, and was given a special overhaul; had a new machine been purchased, a 4-in. type would probably have been obtained as being more suited to the work. The rods were H in. hollow round steel with a type "1" Jackrod thread. Couplings were of chrome steel, and were H in. in diameter, and 2 in. long. Jackbits (type "1" thread) in sizes from 2 in. to 4 in., with 1-in. gauge changes, gave a range of nine bit sizes. They were resharpened by hot milling, and were not milled to a definite gauge size.After sharpening, bits were sent underground without sorting into sizes, the drillers selecting the next bit with callipers. In view of the small scale of operations, it was not considered worth while to adopt special measures, such as the cold grinding of bits, which might have given a better product. Later, however, new bits were used exclusively, the idea being to accumulate enough blunt Jackbits to warrant a thorough treatment of the sharpening...

Jan 1, 1941

By J L. Mauk

The Gladstone Hill area hosts epithermal veins similar to those at Martha Hill, which is less than one kilometre away. There are several vein types in the Gladstone Hill area including (1) pyrite-marcasite, (2) quartz, (3) base metal sulfide, and (4) calcite. Pyrite veinlets formed first, whereas the quartz and carbonate veins formed later. The base metal sulfide vein occurs at depth and is predominantly comprised of quartz and chlorite intimately intergrown with pyrite, sphalerite, galena, and rare chalcopyrite. Platy calcite and massive calcite veinlets were the last vein types to form. Several vein textures occur in the Gladstone Hill area, including colloform and crustiform banding, lattice-bladed, zonal, comb, massive and feathery textures. Crustiform banded veins are the dominant texture and contain variable gold-silver grades. Colloform banded veins consist of ubiquitous quartz and minor chalcedony with gold grades as high as 60 g/t. The lattice-bladed texture forms from the deposition of calcite, which has been replaced in many samples by quartz, indicating that boiling and later cooling has taken place. Unreplaced platy calcite only occurs at deeper levels (>300 m). Zonal and comb textures are preserved in quartz and late-stage amethyst veins. Feathery textures within quartz are commonly associated with breccias and some colloform banding, and with significant Au-Ag grades.   The homogenisation temperatures (Th) of primary and secondary inclusions in quartz, amethyst and platy calcite range from 166 to 274¦C, with salinities <1.3 wt% NaCI equiv. The presence of vapor-dominated inclusions and primary fluid inclusions in platy calcite suggests that boiling occurred intermittently throughout deposition. The veins formed under a relatively flat lying paleowater table that occurred 280 - 300 m above sea level. The fluids involved in vein formation were alkali chloride in composition and low in CO2.

Jan 1, 2001

By S. Mostaghel, S. Nicol, M. Y. Solar

Once upon a time, the process engineer developing the design criteria for a new saprolite ferronickel smelter had it easy: most ores were around 2.5% Ni, with a Fe/Ni ratio of 4 to 5 and a SiO2/MgO ratio of about 1.6; to use the French word: garnierites. The ferronickel grade selected was the conventional 20 to 25% Ni and the impurity levels could be predicted from well established [C], [Cr] and [Si] vs (FeO) graphs. However the process engineer can no longer depend on statistics to design smelters: Ni grades are decreasing while the goethite contents are increasing; SiO2/MgO ratios vary from 1 to 3; and Al2O3 concentrations are reaching levels that cannot be ignored. Mechanistic models must be developed to select or predict essential parameters such as kiln and furnace reductions, ferronickel grade, slag losses, metal and slag liquidus, operating temperatures, etc. But these models must be simplified so that they can be used on a routine basis; and they must be calibrated against a wide range of commercial operations in order to yield the most realistic predictions possible. The present paper proposes one possible approach, using FactSage as a basic source of thermodynamic data. The predictions thus obtained are compared to actual performance for two well documented operations, as well as to the predictions made with other tools that might be more accessible.

Jan 1, 2014

By C A. Locke, J Cassidy, J L. Mauk

The Waihi-Waitekauri region hosts numerous low-sulfidation epithermal deposits that both outcrop and occur at depth. Zones of intense hydrothermal alteration enclose the Au-Ag bearing quartz vein deposits. Hydrothermal alteration includes the destruction of magnetite by hydrothermal fluids, pervasive silicification adjacent to quartz lodes and potassium enrichment due to adularia and illite deposition. High-resolution airborne magnetic and radiometric, and new gravity data delineate distinct geophysical anomalies associated with hydrothermal alteration and mineralisation. Five magnetically quiet zones occur in the region varying in size from 3 to 34 km2 and in geometry from circular to irregular zones. These zones represent the near-surface extent of strong to intense hydrothermal alteration associated with fossil geothermal systems. All epithermal deposits in the region occur in magnetically quiet zones. Over 120 new gravity stations together with existing data across the Waihi district have defined a positive Bouguer gravity anomaly coincident with the magnetically quiet zone. Eastern and western gradients of 50 gu/km bound the anomaly that contains two flat gravity highs west and east of the Waihi deposit. Strong potassium signatures in airborne radiometric data correlate with outcropping zones of alteration and are consistent with the presence of adularia and illite minerals. Hydrothermally altered zones are represented by areas of low Th/K ratios as a result of low thorium concentrations in andesite and elevated potassium levels in altered zones.

Jan 1, 2003

By J. A. Flinn

Phelps Dodge’s Morenci copper mine has had six drills, six track-dozers, 16 shovels, two loaders, and 90 haul trucks equipped with either Caterpillar, Aquila, or Modular GPS systems for nearly three years. The Caterpillar Computer-Aided Earthmoving System is an open-architecture system, which allows for inputs to enhance orientation solutions and system functionality. This system has begun a new phase that leads to an intelligent mining system. Optimization techniques of the current system and inputs are reviewed. In addition, some practical issues of implementing new technology in a mining environment have been identified to aid in this new phase.

Jan 1, 2000

By T. R. A. Gokcen

THE possibilities of separating and purifying metals by high vacuum distillation were examined by Kroll.1 He suggested vacuum treatment for the removal of zinc from the lead produced after Parkes desilverizing. The St. Joseph Lead Co. developed the first commercial vacuum dezincing process at their Herculaneum refinery, as described by Isbell.² The Broken Hill Associated Smelters at Port Pirie, Australia, has, after several years of pilot plant operations and fundamental investigations, developed a continuous process, which will be described briefly in a forthcoming publication." As the full-scale continuous vacuum dezincing plant at Port Pirie is still experimental, publication of full practical details of the plant will be deferred until the unit is operating as a normal part of the continuous refinery. This paper deals only with theoretical aspects of vacuum distillation processes, with particular reference to vacuum dezincing. The method of mathematical analysis is of general interest as it may be applicable to other metallurgical separations which have been investigated recently.4-6 Evaporation Processes At about atmospheric pressure, or higher, most liquids possess a boiling point—a temperature at which any heat put into the liquid is absorbed only as latent heat, not as specific heat. If a steady heat input is supplied, the liquid's temperature rises to this value, then remains constant while bubbles of vapor form beneath the surface. The rate of evaporation is determined solely by the rate of heat transfer to the liquid; the temperature of boiling is determined by the partial pressures of the volatile constituents in the liquid, and the total pressure above the surface. If the rate of heat transfer to the liquid is increased, the temperature remains constant, and the rate of boiling increases. When evaporating metals under vacuum, however, the partial pressures concerned are generally so small that boiling does not occur, because at even a fraction of a millimeter below the surface the hydrostatic pressure is usually too great to permit the formation of a pocket of vapor. In addition, the high thermal conductivity of metals tends to prevent the local superheating which is necessary for bubble formation.' Although this effect is doubtless also exerted when boiling metals at higher pressures, the magnitude will be less because the degree of superheat required to form bubbles is very much less at the higher temperatures involved. Under vacuum, therefore, evaporation of volatile constituents takes place only from the exposed surface, and the rate of evaporation depends upon the surface area, the surface concentration of volatile constituents, the surface temperature, and the partial pressures of volatile constituents immediately above the surface. If the heat input is raised above a certain level, the effect is not to increase the evaporation rate at constant temperature, but to raise the temperature of the liquid until at some higher level an increased rate of evaporation (and thus of latent heat absorption) again balances the heat input rate.? Many substances (including metals) have a very large intrinsic evaporation rate at quite low temperatures—far below their normal boiling points. However, at atmospheric pressure, the large numbers of atoms evaporated are almost completely deflected back into the liquid (or solid) surface by air molecules. Thus the back condensation rate is practically equal to the gross evaporation rate, and the net evaporation rate is practically zero. It can therefore be seen that an overall distillation rate depends not only upon the intrinsic evaporation rate, but also upon the ability of the volatile atoms to move away from the evaporating surface. This movement is facilitated by the provision of a condensing surface close by. Vacuum Distillation: The function of the vacuum above the evaporating surface is to remove foreign molecules, so that the chances of deflection of an evaporated atom back into its source are reduced. When the residual gas pressure is reduced so far that the evaporated atoms have a high probability of reaching a nearby condensing surface without suffering collision with a foreign molecule, the state of affairs is termed "molecular distillation." This process is practiced commercially today for the purification of numerous organic chemical products of high unit value, but not, to the writer's knowledge, for any metallurgical separation. When the degree of vacuum produced in a still is not sufficient to promote molecular distillation, then the evaporated molecules must diffuse through the

Jan 1, 1954

By Khosrow Ebrahimi

We document the occurrence, mineralogy and firing properties of magnesite from hydrothermal deposits in the upper Cretaceous ophiolites of Eastern Iran. These deposits occur as thin veins of nearly pure cryptocrystalline magnesite with only trace amounts of quartz, calcite, and dolomite. Ratios of CaO/SiO2 in the bulk ore are variable. The composition of dead-burned magnesite from these deposits, calcined at different temperatures and durations, is predictable from phase equilibria. Textures of the calcined magnesite were studied by SEM; results show that the principal impurites produced during calcination are forsterite, monticellite, merwinite, dicalcium and tricalcium silicates, and that these are located principally at triple junctions of the periclase crystals. The size of periclase crystals increased with temperature and duration of calcination and the amount of periclase-periclase grain contacts was reduced by increasing the concentration of impurities in the starting products. EPMA show: 1) that CaO and FeO contents in periclase increase steadily with an increase in the CaO/SiO2 ratio and the FeO content of the bulk ore, respectively, and 2) that limited solid solution exists between impurites. This study demonstrates that high quality dead-burned magnesia refractories can be produced from the Iranian magnesite with low CaO, SiO2 and FeO contents.

May 1, 2004

By E. Dernedde

Cell rooms of aluminium smelters have large openings in the sidewalls and in the roof. These openings provide a high ventilation rate, which removes heat and contaminants emitted by the reduction cells and thereby ensures acceptable working conditions inside the cell room. However the large openings make the airflows through the smelter building sensitive to the wind. In this study equations for the airflow through the openings of a smelter building exposed to crosswinds were developed and verified against plant measurements. The equations were then used to estimate the airflows through a two-storeyed smelter building containing VS Soderberg cells. Wind protection by wind-covers over the sidewall openings and by upwind buildings made the airflows through the building less sensitive to the wind. Physical and mathematical modelling showed that working conditions inside the wind-protected cell room would be acceptable for crosswinds at speeds up to 16 km/h. These predictions were confirmed by measurements taken in a VS Soderberg smelter.

Jan 1, 2007

By W. H. Bassett

ABOUT twenty-five years ago the copper industry had outgrown the Lake Superior production. The electrolytic copper producers had- their process well in hand and the industry was well started in the use of electrolytic copper, both for working into wire and sheet, and for the making of alloys. The trade knew that some brands of copper made good material and that other brands did not. There came together a group of men-a refiner, a rolling-mill man, and a manufacturer of electrical machinery-each of them desiring to know why there was a difference and what .it was. Much investigation was done with wire bars and cakes which involved ' chemical analysis, metallographic examination, physical tests and electrical tests. To find the influence of different kinds of copper in making brass 200 carloads of ingots were made into ,eyelet brass under careful observation; each carload was carefully analyzed and tested before used. The alloy was made and rolled under standard conditions and the results recorded.

Jan 1, 1924

By H. Somekawa

The fracture toughness and deformation structures an AZ31 magnesium alloy processed by equal-channel-angular extrusion (ECAE) were investigated. The average grain sizes of as-ECAE and annealed-ECAE alloys were 4.0 and 16.3 µm, respectively. The plane-strain fracture toughness, Kip, in as-ECAE and annealed-ECAE were estimated to be 27.3 and 23.5 MPam1/2, respectively, by stretched zone analysis. The fracture toughness indicated higher value with grain refinement. From optical microstructural observations in samples after fracture toughness tests, although deformation twins were observed in annealed-ECAE, no deformation twins were observed in as-ECAE. From TEM observations, the dislocations on basal and non-basal planes were activated in as-ECAE. With grain refinement, the activations of dislocations on both basal and non-basal planes were possibly related to the reduction in formation of deformation twins in as-ECAE. In addition, in comparison with direct extruded process, ECAE process was more effective method to improve the fracture toughness in magnesium alloys.

Jan 1, 2006

By D Vidyarthi

Blasting is the most important activity in the mining industry, the world over. It is a well known fact that only part of the explosive energy gets utilized in causing the actual rock fragmentation. The rest of it gets converted into blast-induced ground vibrations and noise. Though blast vibrations cannot be totally eliminated, it is possible to minimize them by optimization of blast parameters. This paper highlights various in-house efforts put forth by the author towards site specific blast optimization and the monitoring of blast vibrations. It also deals with the prediction curves developed by regular regression analysis for the prediction of ‘blast vibrations’, ‘peak particle velocity’, ‘safe charge’ for various blasts.

Jan 1, 2007