Search Documents

By A. P. Williams

"This paper presents an overview of plant electrical systems in general, a discussion of the problems that may occur due to plant growth, the maintenance required to maintain the reliability and safety of the electrical system, and the selectivity of the relay protection system. It is divided into two main areas: short circuit levels within the plant electrical system; and relay protection systems.This information is directed at maintenance supervisors, mine managers and electrical superintendents who have been away from detailed short circuit and relay coordination calculations for some time. It points out the potential problem areas within an operating plant electrical system. Short Circuit LevelsTheoryThe electrical equipment in a plant such as breakers, switches and starters has two short circuit ratings, the momentary rating and the interrupting rating. These ratings may be given in MVA or current (amperes) depending on the equipment and manufacturer's preference. Since for a three-phase system MVA and amperes are related by the formula"

Jan 1, 1987

By R. L. Pienaar

Paper written on project work carried out in partial fulfilment of B Eng (Min. Eng.) degree A study was conducted to investigated and compare the feasibility of two single level extraction layouts for an intact part of theorebody of the De Beers diamond mine, Koffiefontein. Two layouts were chosen and the tonnage profile, development schedule and production ring blast layouts were calculated by applying the information acquired through a literature study. Current principles used on the mine were also applied. The first layout chosen is described as a simple straightforward layout with 6 production tunnels spaced 15 m apart, and is referred to as Layout A. The second layout, named Layout B, is described as a complex chevron layout with 9 production tunnels spaced 15 m apart. This layout has a rim tunnel situated in the kimberlite ground, which is called a chevron and this made the layout more complex than Layout A. By comparing the financial results of the two layouts, it was found that Layout B is a more feasible option than Layout A. Sensitivity analyses show that both layouts are extremely sensitive to the revenue of the projects. Therefore it is recommended that Layout B can prove to be a source of additional tonnage to add to the total tonnage profile of the mine and to extend the life of mine by 20 months, only if certain financial/economic factors improve. There is, however, still some areas of the project that need to be investigated.

Jan 1, 2006

By James P. Bennett

The Bureau of Mines investigated the role of imported natural flake graphite in dolomite-carbon refractories used in steelmaking processes. Fundamental engineering data were obtained to enable the evaluation of substitute materials. Changes in oxidation resistance (2,000° F), hot strength (2,750° F), and deformation under load (2,7500 F) caused by 10-wt-pct additions of five different kinds of natural flake graphite and increasing quantities (0 to 30 pct) of a 90-pct-carbon natural flake graphite were studied. Results indicated that carbon purity of 10-wt-pct-graphite additions did not influence hot strength or deformation under load. When the quantity of 90-pct-carbon graphite addition varied between 0 and 30 wt pct in a dolomite-carbon brick, hot strength was highest and de-formation under load lowest with 10-wt-pct additions. As hot strength test temperature was increased from 5000 to 2,750° F, the strength difference observed between 0-and 30-wt-pct additions of a 90-pct-carbon graphite became smaller. Additions of a boron-treated graphite caused significantly higher strength and lower deformation under load at high temperatures, while an addition of ball clay significantly reduced strength and increased deformation.

Jan 1, 1987

Effect of Hydrophobicity and Frother Concentration on Bubble-Particle Interactions in Turbulent Flow

Sep 13, 2010

By J. E. Nesset, S. R. Rao, J. A. Finch

"For base metal sulphides, iron rejection starts in mineral processing. This review focuses on changes in plant practice specifically to improve iron sulphide rejection by control of contaminant ion effects and discusses selected general innovations in mineral processing that can be expected to play a role. One group of changes to control contaminant ions is in size reduction (the use of stage grinding and inert stirred milling) and another is in system chemistry (order of reagent addition and exploitation of the flexibility of sulphoxy reagents). Plant examples illustrate the successes, indicating that there are several options available. The general innovations start by considering the new tools for measuring gas dispersion properties and quantifying froth characteristics by imaging. Examples of their application to improve concentrate quality illustrate the potential. Other innovations stress adapting geostatistics to model variation in milling and flotation response to provide feed forward control and rigorous application of statistical experimental methodology in plant test work. An example from one concentrator shows improvements in concentrate quality from application of basic principles can be impressive.INTRODUCTIONThe more iron control (rejection) that can be accomplished in mineral processing the lower the subsequent metal extraction costs and environmental implications of iron disposal, particularly in hydrometallurgical processes. Iron rejection has been a contributing target to periodic attempts to apply mineral processing to nickel laterites and bauxites but the prime application is control of pyrite and pyrrhotite (iron sulphides) in the treatment of sulphide ores by flotation. In this paper some new concepts and innovations introduced in sulphide flotation plants over the past ten years or so (i.e., since a previous review [1]) will be outlined with examples of how they have contributed to improved “iron control”.To increase rejection of iron minerals, first the recovery mechanism should be understood. There are four principal ones, two physical in origin: 1, via locked particles (i.e., flotation of composite particles due to insufficient size reduction to liberate the minerals) and 2, through entrainment in the water reporting to the float product (an unselective process); and two originating from a response to the system chemistry: 1, true flotation (i.e., iron sulphides becoming hydrophobic) and 2, as a result of iron sulphides forming aggregates with hydrophobic particles (e.g., ”slime” coatings). There has been considerable effort to diagnose which of these dominates iron sulphide recovery; in many cases it is due to “chemistry”, in particular true flotation. The flotation effect often appears related to contamination by metal ions [1]. This can reduce selectivity in two ways: 1, metal ion species may activate iron sulphides, or 2, cause general depression which demands more vigorous flotation conditions (e.g., additional collector) with consequent loss of selectivity. This is where the review will start, by considering ways to control contaminant ions."

Jan 1, 2007

By Claude Bazin

"Laboratory semi-batch flotation tests were conducted using two different sulphide ore samples. The size reduction was adjusted to cover a wide range of flotation feed size distributions. Results show that similar recoveries can be achieved independently of the fineness of grind. This result suggests that possible energy savings could be achieved by a redistribution of the power between the grinding and regrinding mills. The behaviour of the selectivity curves shows that some gangue minerals are more sensitive to particle size than other ones, implying the existence of preferential associations between minerals in the ore.INTRODUCTIONInteractions between grinding and flotation have been studied for many years, and still a robust model to link the two processes lacks to be developed (Girard et al., 2005; Bazin et al., 2001). The ore size reduction liberates mineral grains, while flotation separates them into valuable minerals and gangue. The more size reduction that is applied to the ore the more important is the mineral liberation but also the production of fine particles that can pose problems during flotation (Trahar and Warren, 1976). The definition of the grinding requirement for flotation is a complex problem (Rickelton and Dell, 1977; Sosa Blanca et al., 2000; Morrison, 1993; Wei and Gay, 1999).This paper analyzes the effect of the fineness of grind using semi-batch flotation test results. The first two sections describe the test procedure and the results. The third section analyzes the results in terms of liberation and selectivity, and proposes a possible redistribution of power between grinding and regrinding mills."

Jan 1, 2006

By H. W. Camp

The past year has had no revolutionary change in the process of petroleum refining, although there have been improvements and developments in practically every phase of operation, due largely, perhaps, to economic pressure. A few years ago, a Mid-Continent skimming plant using 35 gravity crude obtained 28 per cent. gasoline and naphtha; 9 per cent. kerosene, and the remaining yield gave gas oil and fuel oil. Figuring manufacturing cost, but not including sales, transportation, overhead and depreciation, the realization was $1.45 per bbl. of crude. Today, a thoroughly modern and up-to-date skimming plant, having all latest equipment, shows a realization of $1.74 per bbl. on the same basis. Thus it is evident that progressive developments have taken place in the last 2 or 3 years when potential earnings have been increased about 20 per cent. The average refiner is compelled to exert his utmost ingenuity in order to operate with a profitable margin. He has two factors to consider—recovery of maximum yields of profitable oils and the reduction of operating expenses. For the past 8 years, the margin between price of gasoline and cost of crude has grown narrower, constantly. Both these prices are determined by external conditions and not by the refiner himself, but the refiner might have been able to increase that margin had he more carefully controlled his output, limiting his production of light oils to current consumption. Be that as it may, this same economic pressure has given impetus to progress in improvements of primary distillation equipment, including stills, towers and heat-saving devices. A pipe still and bubble cap fractionating equipment can now replace a battery of shell stills, giving better yields, better control, elimination of rerunning and lowering of operating costs. The most recent pipe stills are being equipped either with radiant-heat furnaces or air-preheating systems and improved heat exchange equipment. These can be operated on a fuel consumption as low as 1 per cent. of the charge as compared to a fuel consumption of

Jan 1, 1929

By A. Kenneth Schellinger, O. Cutler Shepard

Overgrinding, Or the breaking of ore particles into sizes smaller than required for liberation, is a first-magnitude problem in grinding for concentration processes. The conventional ball mill-classifier circuit used in commercial grinding produces mineral particles that are all ground to pass an upper size limit, while the proportion of very fine sizes, or slimes, is uncon rolled. Calculations based on measurements made in commercial plants which were grinding ore for flotation concentration indicate that about go pct of the energy used in grinding is consumed in useless overgrinding.1 In addition to accounting for the consumption of a large amount of energy, over-grinding is detrimental to the flotation process. Overground slime coats larger partitles and inhibits selective action by the flotation reagents on particles which by themselves could be separated very well. A further difficulty is that extremely finely ground minerals do not respond satisfactorily to flotation-collecting reagents, and both selection and recovery decrease markedly with particles finer than 5 to 10 microns.2 conventional classifier-ball mill circuits inherently tend to overgrind the valuable minerals more than the gangue minerals because most valuable minerals are of higher density and are softer and more friable than the gangue minerals. The rem- edy to this situation would seem to be a separating mechanism which would separate free valuable mineral particles regardless of size and density considerations and a mechanism which would operate in the grinding mill so that valuable mineral grains would be removed from the grinding machine as soon as they are freed. A consideration of these ideas led the authors to the conception of a simultaneous grinding and flotation mechanism. So far as the authors are aware, such a machine has never been tried, even on a laboratory scale. Development oF Apparatus and Experimental Method Apparatus development went through several stages before a really workable machine was devised. Work was started with a large cast-iron mortar 7½ in. in diameter and 8 in- deep. A cast-iron disk Was mounted on the end of a vertical shaft SO that it fitted loosely into the bottom of the mortar. On top of the disk four radial cleats ¼ in. high were bolted to agitate the ball charge as the disk, or impeller, rotated. The vertical shaft was driven at 100 rpm by a mechanism improvised from an old coffee-mill type of grinder. A hole was drilled into the bottom of the mortar through which compressed air was introduced for frothing. In operation, more charges of Ore which had been crushed to pass an 8-mesh screen were placed in the bowl along with water and suitable reagents. The impeller was then started and the compressed air turned On so that the ore was ground while being exposed to air bubbles. Mineralized froth was

Jan 1, 1949

By T. Banerjee, D. Felsher, G. Leavoy

"Lake Shore Gold is engaged in commercial gold production at both the Timmins West and Bell Creek mines, located in Timmins, Ontario. Run of mine ore is processed at the Bell Creek mill which consists of a conventional gold mill flow sheet involving crushing, grinding, gravity concentration and carbon-in-leach (CIL) for gold recovery. Since 2009, the operating capacity of the mill has been upgraded from 2000 tpd tonnes per day (tpd) to over 3,000 tpd. The most recent expansion involved the installation of a low aspect ratio SAG mill to replace the secondary crusher. Without operational data on the low aspect mill, combined with a site team that was new to SAG milling, there were many challenges in achieving the target throughput from the circuit. Through the implementation of AwaRE advanced controllers, running in closed loop with PRC fragmentation cameras as well as embedded PARC modules within the Allen Bradley PLC, the site was able to rapidly develop a best operating practise and has been successful in creating a stable and consistent operational environment. The process, lessons learned and eventual solution will be reviewed in this paper.INTRODUCTIONLake Shore Gold is engaged in commercial gold production at both the Timmins West and Bell Creek mines, located in Timmins, Ontario. Run of mine ore is processed at the Bell Creek mill which consists of a conventional gold mill flow sheet involving crushing, grinding, gravity concentration and carbon-in-leach (CIL) for gold recovery. Since 2009, the operating capacity of the mill has been upgraded from 2,000 tpd tonnes per day (tpd) to 3,150 tpd. The most recent expansion involved the installation of a low aspect ratio SAG mill to replace the secondary crusher. This endeavor was split into two phases: the expansion of the back-end (Phase 1) and the front-end (Phase 2) of the mill. Phase 1 of the expansion was completed at the end of 2012 and involved enhancements and capacity addition to the leaching and adsorption circuits, which increased the mill’s capacity to 2,500 tpd. Phase 2 of the expansion commenced at the end of July 2013 and involved the expansion of the crushing and grinding circuits. The expanded front-end of the mill now has a capacity of 5,500 tpd, and processes ore from both Bell Creek and Timmins West mines. The updated flow-sheet, as shown in Figure 1, illustrates the replacement of the two-stage crushing and ball milling circuit with a single stage crusher and a low aspect ratio SAG mill."

Jan 1, 2015

By Nobuaki Sato

The electrical conductivity, k, of pure and sodium doped sulfur melts was measured with and without ultrasonic waves at temperatures ranging from 140 to 340'C by the two probe method using an ultra high resistance meter. The k value of the pure sulfur melt with irradiation jumped at around 170°C by an order of 102 after which it mouutuniocally increased from 10-5 to10-4 A' 1 cm-1 with an increase of the temperature. The addition of the sodium metal to the sulfur melt was found to cause a larger jumping in the K value. The k value increased with the increase of Na proportion in the melt. For a 10mol% Na doped sulfur melt it was as high as max ~30 A 1cm -1 above 180 C under the irradiation of of ultrasconics.

Jan 1, 2003

By F. J. Tavera, J. A. Finch

A probe suitable for on-line measurements of gas hold-up in industrial flotation systems has been developed. It is based on an open cell for measurement of slurry-gas conductivity and a novel syphon cell for measurement of slurry-only conductivity. The desired behaviour of the two cells was demonstrated and estimates of gas hold-up were shown to be in good agreement with independent measurements. The gas hold-up probe was used as a diagnostic tool to assess the operation of flotation columns. Differences in gas hold-up between baffled sections in two industrial columns were detected

Jun 18, 1905

By A. Kenneth Schellinger, O. Cutler Shepard

INTRODUCTION OVERGRINDING, or the breaking of ore particles into sizes smaller than required for liberation, is a first-magnitude problem in grinding for concentration processes. The conventional ball mill-classifier circuit used in commercial grinding produces mineral particles that are all ground to pass an upper size limit, while the proportion of very fine sizes, or slimes, is uncontrolled. Calculations based on measurements made in commercial plants which were grinding ore for flotation concentration indicate that about 90 pct of the energy used in grinding is consumed in useless overgrinding.1 In addition to accounting for the consumption of a large amount of energy, overgrinding is detrimental to the flotation process. Overground slime coats larger particles and inhibits selective action by the flotation reagents on particles which by themselves could be separated very well. A further difficulty is that extremely finely ground minerals do not respond satisfactorily to flotation-collecting reagents, and both selection and recovery decrease markedly with particles finer than 5 to 10 microns.2 Conventional classifier-ball mill circuits inherently tend to overgrind the valuable minerals more than the gangue minerals because most valuable minerals are of higher density and are softer and more friable than the gangue minerals. The remedy to this situation would seem to be a separating mechanism which would separate free valuable mineral particles regardless of size and density considerations and a mechanism which would operate in the grinding mill so that valuable mineral grains would be removed from the grinding machine as soon as they are freed. A consideration of these ideas led the authors to the conception of a simultaneous grinding and flotation mechanism. So far as the authors are aware, such a machine has never been tried, even on a laboratory scale. DEVELOPMENT OF APPARATUS AND EXPERIMENTAL METHOD Apparatus development went through several stages before a really workable machine was devised. Work was started with a large cast-iron mortar 7 ½ in. in diameter and 8 in. deep. A cast-iron disk was mounted on the end of a vertical shaft so that it fitted loosely into the bottom of the mortar. On top of the disk four radial cleats ¼ in. high were bolted to agitate the ball charge as the disk, or impeller, rotated. The vertical shaft was driven at 100 rpm by a mechanism improvised from an old coffeemill type of grinder. A hole was drilled into the bottom of the mortar through which compressed air was introduced for frothing. In operation, weighed charges of ore which had been crushed to pass an 8-mesh screen were placed in the bowl along with water and suitable reagents. The impeller was then started and the compressed air turned on so that the ore was ground while being exposed to air bubbles. Mineralized froth was

Jan 1, 1947

By D. W. Butner

This report is concerned with the conditions affecting the methods and costs of mining phosphate rock in that part of the western phosphate field that is in Bear Lake and Caribou Counties in southeastern Idaho ( see fig . 1) . The area was selected because it contains most of the known phosphate reserve and because its geology has been studied more extensively than that of other sections . Deposits of phosphate rock on public land may be leased from the Government under the terms of the Mineral Leasing Act of 1920 , subject to the regulations of the Bureau of Land Management . Public interest in phosphate production is growing , as shown by an increasing number of applications for leases . Two mines are being operated steadily for the production of phosphate rock by companies that have also the necessary processing plants for the manufacture of fertilizer . Total western phosphate - rock production in 1947 is reported by the Economics Statistics and Division of the Federal Bureau of Mines to have been 1,193,000 long tons , mined in Idaho , Montana , and Wyoming . The average grade was 30.7 percent of contained phosphorus pentoxide (P205 ) ; the average value at the mines was $5.67 per long ton . Idaho contributed 905,000 tons , or somewhat more than 75 percent of western production . Western fertilizer plants took 23 percent of total production; 76 percent was exported . Strip mining accounted for 75 percent of the Idaho tonnage; the remainder was stoped from underground workings . Rock must contain a minimum of 30 percent P205 to be commercially useful for the production of superphosphate fertilizer by current acid treatment methods . Research by corporations and Government agencies has been directed toward the use of lower - grade ore . So far , only by smelting can rock containing as little as 25 percent P205 be used economically . Any development of processing or use pattern that would render the mining of , say , 20 percent rock profitable would have important effects in reducing the unit cost of mining . In the search for metallurgical improvements , consideration should be given to the saving of valuable components of the rock, such as vanadium and fluorine , both of which are present in the beds .

Oct 1, 1949

By D N. B Skinner

Changes in the configuration of late Cenozoic volcanic arcs related to Pacific-Australian plate convergence in northern New Zealand may have localised large-scale epithermal gold-silver mineralisation to a particular part of the volcanic arc system, the Coromandel Volcanic Zone (CVZ). The history of arc-type volcanism in northern New Zealand began with the development of the continental margin Northland Volcanic Arc from early-mid Miocene (26-15 Ma). From 18-15 Ma the Northland Volcanic Arc extended south into the northern and western part of the CVZ where it is dominantly composed of andesite with lesser dacite and very minor rhyodacite. In the south, centre and east of the CVZ, younger andesite-dacite volcanism overlapped in space and time (14-5 Ma) with voluminous rhyolitic volcanism associated with rift-hosted calderas and minor basaltic eruptions. This change to bimodal rhyolitic-basaltic volcanism and extensional tectonics was a result of southwest (SW)-directed propagation of the Colville-Lau oceanic island+ arc into the north-northwest (NNW) trending Northland Volcanic Arc and its underlying continental crust. The extensional tectonic regime created in the collision zone between the two arcs is also the site of the 14-6 Ma Coromandel epithermal gold-silver province, which contains some 50 separate deposits and has a production (1862-1996) of about 300 t Au and 1150 t Ag. Extensional tectonics facilitated the emplacement of silicic magma at shallow crustal level and led to reactivation of deep basement faults. The resulting enhanced heat flow and fault-focused fluid flow localised large hydrothermal systems and associated extensive low-sulphidation epithermal gold-silver deposits in the southern part of the province, as at Waihi, Golden Cross and Karangahake.

Jan 1, 1997

By R. J. Sweigard, C. T. Justice, T. Beckham, E. D. Thompson, T. C. Hopkins

Fine coal refuse is often pumped, as slurry, into surface impoundments as a means of permanent disposal. As the available volume is filled, the height of the embankments are frequently increased. Many times the additional embankment material is placed upon consolidated fine coal refuse. There has been some concern about the long-term effect of consolidation of this material at or above the liquid limit upon its shear strength. A laboratory investigation was performed using three different types of fine coal sluny taken from Central Appalachian coal preparation plants. The refuse was consolidated in 10-foot plexiglass columns under incremental amounts of surcharge loading. The incremental loads were designed to simulate the effect of increasing the height of a refuse embankment on top of the consolidating coal slurry. After the refuse in the columns had consolidated for several months, the columns were cut apart and triaxial tests were performed on both the consolidated material and unconsolidated material for comparison of their shear strength parameters.

Feb 24, 1997

By Mike Lovitt

New Gold Inc. had commissioned Orica to assist with the design of the drawbell blasting at New Afton Underground copper/gold block cave at Kamloops, British Columbia, Canada. Orica have had much success in developing the single-shot drawbell method at Freeport Indonesia in 2001 in the Deep Ore Zone and they will be using it exclusively in their new Grasberg Underground Operation. RioTinto Northparkes have also used the single shot drawbell blasting in their Second Lift E26 Project and even in the E48 orebody which is a post undercut block cave, realising the safety and operational benefits of this blasting method.

Jan 1, 2013

By Y. P. Chugh

Additional field evaluations of a modified continuous miner using a new spray system and modified scrubbers have been conducted by the authors. In this demonstration, a comprehensive package for dust control on a continuous miner which included previously developed modifications to the scrubber, scrubber intakes and the innovative chassis spray system was demonstrated. Side-by-side comparisons of the modified miner and regular miner indicated that the miner operator with the modified miner was exposed to 62% less respirable dust. Ram car operators with the modified miner had 38% less respirable dust exposure and the return air on the modified miner had 19% less respirable dust. The mining conditions during side-by-side testing were very comparable. These results support the findings of the modified spray system studies conducted earlier at different mines in Illinois on four occasions and the modified scrubber system field evaluation studies.

Jan 1, 2009

By R. Barany

The heats of formation of goethite, ferrous vanadate, and manganese molybdate at 298.15° K were determined by solution calorimetry. For formation from the elements, the heat values were -133.7 ±0.3 kcal/mole for goethite, -453.8 ±0.5 kcal/mole for ferrous vanadate, and -284.8 ±0.2 kcal/mole for manganese molybdate. For formation from the oxides, the heat values were -0.9 ±0.1 kca1/mole for goethite, -19.4 ±0.3 kca1/mole for ferrous vanadate, and -14.6 ±O.l kcal/mole for manganese molybdate.

Jan 1, 1965

By P. E. Christensen

Due to ever-increasing stripping ratios associated with the No. 8 Seam at the San Juan Mine surface operation, BHP Minerals decided to implement longwall mining for the extraction of the substantial future reserve base. In preparation for longwall developments, BHP opted to first develop a small-scale pilot operation within the No.8 Seam on an adjacent lease to address geotechnical/geological concerns related to ground control, subsidence, caving, panel and entry design, and operational issues related to entry development and proper face equipment selection. Room-and-pillar mining methods are currently being utilized to develop a full extraction panel for a wide range of geological, geotechnical, and geomechanical evaluations aimed at characterizing and assessing the mineability of the No.8 Seam. Variable roof and floor conditions, coupled with a multi-bench coal seam, require that a number of mining horizons, opening geometries, and roof and rib support fixtures be evaluated relative to expediting gate and panel developments. Issues related to development of timely caves in areas subject to overlying sand channel deposits will also be addressed through underground in-seam stress and deformation measurements, and interburden and surface subsidence monitoring. This information will ultimately be used to evaluate face support and gate and panel pillar/entry development requirements. The current depositional model for the property, developed from an aggressive drilling, highwall mapping, and lineament evaluation program, will also be refined during the Pilot Mine study through extensive in-trine mapping, additional roof and floor drilling and physical property testing, and determination of the in situ principal horizontal stress field.

Jan 1, 1998

By R. A. Jankowski

Although the number of operating longwall mining systems has remained relatively consistent over the past five years, longwall production levels have increased significantly during this period. Longwall production currently accounts for approximately 50% of U.S. underground coal production. While longwalls are highly productive and offer other advantages, operations employing this method of mining continue to experience dust compliance problems. This increased longwall productivity has meant that far more dust is being produced. An improved understanding of the longwall face ventilation system and advancement of face ventilation technologies are necessary to ensure all face personnel are allowed to work in an environment that is free of excessive levels of airborne respirable coal mine dust. The Dust and Toxic Substances Control Branch of the National Institute for Occupational Safety and Health's Pittsburgh Research Laboratory has examined several basic principles of the longwall face ventilation system, and has evaluated the effectiveness of numerous improved face ventilation techniques for longwall mining systems. These include identifying improved techniques for measuring face ventilation parameters on longwall mining sections and investigating the fundamental relationship between face air flow and the entrainment and dilution of respirable coal mine dust. Studies have been completed to determine the impact on face dust levels from using belt entry air to ventilate the longwall. Novel methods have been identified to increase the amount of face air flow and to manage face air flow to most effectively minimize face workers' dust exposure. Unique systems of auxiliary face ventilation have been developed and evaluated at full-scale, simulated longwall test facilities. The theoretical and applied aspects of each of these principles and technologies are discussed. Application of these results, throughout the longwall mining industry, as documented from surveys conducted in the early 1980's and 1990's, have reduced the health hazard associated with excessive exposure to respirable coal mine dust.

Jan 1, 1998