Search Documents

By Patrice Baby, Stefano Salvi, al et, Jean Vallence, Galdos, Renzo

The nature of the gold-bearing fluid and the source of gold in sedimentary-hosted gold deposits of Carlin, orogenic or epithermal types is still matter of debate. Most authors point to magmatic/ metamorphic origin for the fluids, however, the properties of such fluids and their interactions with organic carbon – a common component in this type of deposits – are not sufficiently well known. Here we present a large set of novel geochemical, mineralogical and fluid-inclusion data obtained from the Algamarca Au-Ag-Cu epithermal veins, corresponding to lateral manifestation of the neighbouring sedimentary-hosted epithermal-gold deposit at Shahuindo.

May 10, 2023

By D. R. Babich, E. R. Bauer

Noise-induced hearing loss (NIHL) in mine workers, especially underground coal miners, continues to be a problem in the mining industry. The recently enacted MSHA noise standard, Part 62 – Occupational Noise Exposure (Federal Register, 1999), is aimed at reducing NIHL in the mining industry. The U.S. National Institute for Occupational Safety and Health (NIOSH) is conducting a cross-sectional survey of noise sources and worker noise exposures to address NIHL in various aspects of coal mining including surface mining, coal preparation plants and underground mining. In underground bituminous coal mining, noise surveys, consisting of full-shift worker noise exposure, time-motion studies and equipment noise profiling, have been completed on longwall and continuous miner sections in six underground coal mines. The studies revealed widely varying shift-to-shift worker exposures, with workers in certain occupations routinely exposed to potentially hazardous levels of noise. A summary of these studies is reported, including worker dose, source/dose relationships and equipment noise profiles.

One of the most important factors leading to the success of a cement plant is its location. A multicriteria decision-making method is used to rank alternative plant locations. The set of criteria is established and corresponding criteria should be established for each case study, although this multicriteria decision-making approach has broader applicability. In this paper, the analytic hierarchy process (AHP) with 5 criteria is used to develop a location evaluation hierarchy for an alumina?cement plant in East Azerbaijan province of Iran. Five alternatives for the plant location are evaluated. The main criteria are transportation, water supply, power supply, fuel supply and land. Other criteria have the same importance as these five alternatives. The alternatives are ranked by a multicriteria method and the best site is proposed. Keywords: plant location; multicriteria decision-making

Jan 1, 2005

By H. Guo

There are a number of methods available for the determination of the fracture toughness of rock. Some of the most recognised methods include the hollow pressured cylinder, the short-rod, the chevron - edge-notched round bar in bending and the disc-shaped compact specimen. Most of these tests are difficult and expensive to conduct. In this paper the simple Brazilian testing of discs for tensile strength has been used to determine their fracture toughness. Tests were conducted on six different rock types and the values of the fracture toughness obtained for each type are in close agreement with the results of the well recognised the chevron edged types. Details of the tests, and analytical validation of the technique, are presented

Jan 1, 1992

By S N CARRAS

Ore reserve estimation is a procedure involving data collection, data storage and judgement and assumptions about geology mining and metallurgy. Calculations are based on these assumptions and an economic analysis on projected cash flows is carried out. Ore reserve estimation must therefore be subjective and will always depend on the extent to which the assumptions used in arriving at the estimate are correct. This paper is an attempt to summarise the many aspects that can contribute to ore reserve problems and to offer some suggestions on how to minimise these problems. For further details on specific concepts readers are referred to the detailed descriptions in the referenced papers.

Jan 1, 1992

By Reynold Q. Shotts

A study was made of the coal resources of an area in Jackson County, Ala., forming a part of the Flat Rock, Henegar, and Stevenson quadrangles. The area studied is a portion of the Plateau coalfield on Sand Mountain and is near the Tennessee Valley Authority's Widows Creek steamplant. Since no detailed geological study of this area had been published, some reconnaissance work was done. The coalbeds and adjacent strata such as sandstones, conglomeratic sandstones, and conglomerates were studied. Available drill logs, together with the areal geology, provided sufficient information to permit correlation of the coalbeds and an estimation of coal reserves. For all categories of reserves, computed on a regional basis, a total of 72,920,000 tons of coal more than 14 inches thick is estimated for the areas studied in Stevenson, Flat Rock, and Henegar quadrangles. Of this tonnage, 40,001,000 tons is estimated to have less than 60 feet of overburden. The total measured coal reserves for the above three quadrangles are 16,359,000 tons, with 12,411,000 tons under less than 60 feet of cover.

Jan 1, 1966

By E. H. Greener, M. E. Fine

The internal friction (1/Q) of cobalt Fig. 1 (measured by an electrostatic dynamic method1) near 250°C begins to increase rapidly on heating and continues to increase until 560°C, the highest tem- perature measured. In the plot of log of 1/Q against 1/T, above 250°C the data nearly fit two straight lines intersecting at 400°C, approximately the temperature of the hexagonal-cubic transformation. The higher temperature branch corresponds to an effective activation energy of 6500 cal per mole, the lower temperature branch 11,000 cal per mole. Young's modulus Fig. 2 increases approximately

Jan 1, 1959

By Jianhua Xin, Min Chen, Cuihuan Huang, Shan Yu, Xiaoao Li, Nan Wang, Guanghao Chen

Copper enrichment behavior in continuously cast slab induced by scale formation after continuous cooling in H2O vapor atmosphere and consecutively in air has been experimentally investigated by combining with SEM-EDS analysis, for the purpose to examine the effects of initial slab surface temperature and contents of copper and nickel. For Slab 1 with copper content of 0.1 percent, no visible copper enrichment is found at scale-substrate interface irrespective of the various scale microstructures formed at different initial slab surface temperatures. For Slab 2 with higher contents of copper and nickel, copper-rich phase accumulates and stays at scalesubstrate interface under the condition of lower initial slab surface temperature; while Cu-rich phase in the porous scale formed at higher initial slab surface temperature is noted with simultaneous Ni-enrichment appearing in front of the steel-scale interface. Both a porous scale and high nickel content work together to provide pores for copper-rich phase migration away from interface and occlude within the scale layer.

Jan 1, 2016

By M Rankin, F Medina, R Verburg

We conducted a preliminary assessment of an extensive deposit of historic tailings discharged over a period of 40 years to the shoreline along a Southern Peruvian coastline. The tailings formed an extensive beach approximately 2.4 km long and 300 m wide. The tailings consist principally of pyrite (37 to 59 per cent), hematite (nine to 20 per cent), magnetite (three to 13 per cent) and quartz (11 to 36 per cent). The present operating company was required to evaluate the feasibility of capping the ocean side tailings deposit, however, given the size of the undertaking and the potential to reclaim residual minerals from the tailings, it was prudent to first evaluate whether capping would in fact reduce the impacts to the marine environment. Therefore this preliminary assessment examined: 1. metals contamination in tailings, shoreline porewater and marine sediments; 2. reactivity of tailings and acid generation potential; and 3. the potential for biological effects from metal contamination in the uplands tailings (solid phase) and beach porewater. Based on mineralogy, column leach studies and chemical results, the upland tailings have a high geochemical potential to acidify and release metals, especially copper, nickel and zinc, should they be subject to oxygenated and aqueous conditions. But, the extreme arid climate results in very low potential for precipitation and virtually precludes the transport of acid drainage reaction products from the upland tailings towards ocean. Wind erosion caused by offshore winds is likely a small source of tailing transport to the ocean. Since some potential exists to reprocess the tailings in the future, capping does not seem justified at present.

Jan 1, 2003

Case 1: A driller raised a drill rig mast into a 7200-volt overhead power line. Both he and his helper were killed. Case 2: A driller-helper was pulling a winch cable toward a stack of drill steel when the cable contacted a 12,000-volt power line. The helper was killed, and the driller at the rig controls was severely injured. [ ]

Jan 1, 2006

By G. Reinberg, C. D. Clarke

Most underground mining operations are dependent on pumping installations to keep the mine unwatered. The reliability of such installations is obviously of paramount importance. The volume of water to be handled is often considerable, and the total head is relatively high. In these cases, both capital cost and operating expense of the pumping installations will become significant factors in overall mining costs. To insure reliability and to keep efficiencies, and hence operating costs, within acceptable limits it goes without saying that mechanical maintenance of a mine pumping installation must receive scrupulous attention at all times. Large mine pumping installations today almost invariably use multistage centrifugal pumps, since positive-displacement units would not be economically competitive except under very unusual conditions of small volume combined with extremely high heads. Centrifugal pump maintenance, under ideal circumstances, would be confined to parts subject to normal running water, i.e., bearing surfaces, stuffing box packing, and shaft sleeves. Under adverse conditions, however, metal may be lost from the wetted surfaces of a pump by erosive or corrosive action of the pumped fluid, and maintenance costs can easily attain enormous proportions.

Aug 1, 1956

By L Hussey, H Thanasekaran, J Kohmuench

Conventional flotation technology has historically failed to achieve high recoveries when treating <15 µm particles (Lynch et al, 1981). The new StackCell™ flotation technology was developed to specifically target this particle size range, and was tested at pilot plant scale at Mt Keith Nickel Concentrator. The streams tested, Slimes Rougher Tailings and Fines/Slimes Cleaner Tailings, represent 21% and 11% of the total nickel lost to tailings in the plant. Laboratory scale test work indicated that an economically significant fraction of these losses was consistently available to be recovered by additional flotation. The pilot plant experimental scope included over 50 tests. A grade recovery curve for each stream was developed, as well as information on the effect of ore type, feed rate, wash water, air flow, collector and frother on the performance of the cell. The single StackCell was able to achieve nickel recoveries of 16.8% and 16.5% on the Rougher Tailings and Cleaner Tailings, respectively, at grades consistent with these blocks. Additional test work of the StackCell in a cleaner scalper duty yielded final quality concentrate with a maximum nickel recovery of 59.5% for the single stage StackCell. Laboratory scale simulation of the downstream impacts of the StackCell operating as a cleaner scalper indicated a net recovery benefit of up to 2.0% for this cleaner block.Tests were completed to compare residence time requirements of the StackCell, as compared to conventional flotation. In 55 seconds, the pilot plant StackCell achieved 50% of the recovery of a 960 second laboratory scale conventional flotation on the same feed material. The apparent improvement in flotation kinetics is attributed to the novel high intensity aeration system, which provides efficient bubble-particle contact thereby shortening the residence time required to achieve high recoveries. The smaller footprint and lower energy costs of such a cell are also benefits of this technology, which is being considered for industrial scale installation as a result of this test work. Given the industry’s historical poor performance treating slimes with conventional flotation, it is clearly best practice to challenge the status quo through innovative new technology, such as the StackCell.CITATION:Hussey, L, Thanasekaran, H and Kohmuench, J, 2017. The application of high intensity flotation technology at Mt Keith nickel concentrator, in Proceedings MetPlant 2017, pp 259–278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By P. D. Rao, D. E. Walsh

Chemical and physical properties of typical low-rank coal (LRC) ash are significantly different than bituminous coal ash. With the exception of extraneous ash, which is incorporated during mining or is due to ash partings within or between coal seams, LRC ash consists primarily of inherent ash that is bonded into the coal's organic matrix or finely disseminated mineral matter. This paper reviews the nature of LRC ash, both inherit and extraneous, and how this impacts the prospects of washing and utilizing LRCs. A literature review, as well as washability data, proximate and ultimate analyses and ash analysis of 25 Alaskan LRC seams are used as a basis for this discussion. The authors' remit research into the nature and distribution of phosphorous in an Alaskan LRC is also discussed

Feb 24, 1997

The Bureau of Mines evaluated short-delay coal mine detonators manu-factured by three domestic companies for electrostatic sensitivity, strength, and no-fire current level. Electrostatic sensitivity was studied in pin-to-pin and pin-to-case modes employing lO-kV potential. Strength of detonation was measured in the Bureau's underwater test fa-cility. No-fire current was measured using a constant-current power supply unit. Test procedures and experimental data are included.

Jan 1, 1985

The trend for using larger equipment in open pit mining to achieve cost effectiveness raises the question about the optimum economic point of scale in the current world of globalization. The present paper treats this question through the prism of a new methodology of assessing the impact of the size of production equipment on the economic outcomes of coal mining ventures. The methodology incorporates a production scheduling optimization model that implements both principles of mine planning, coal quality optimization and waste deferment. The implementation of the waste deferment principle dealing with the spatial and time aspects of the mine sequence arrangement allows the adequate modeling of the optimality of production equipment scale through the use of mine investment parameters, such as, purchase and ownership costs and discounted cash flows analysis. A case study is provided to illustrate the applicability of the new methodology.

Jan 1, 2004

By Soumendra Basu, Uday Pal, Yang Yu, Srikanth Gopalan, Karl Ludwig, Deniz Cetin, Jacob Davis

"A limiting factor for Solid Oxide Fuel Cell (SOFC) performance is the oxygen reduction reaction (ORR) at the cathode surface. Changes in the surface composition and structure on annealing at 800°C has been studied, since these can influence the ORR. Idealized single crystals of cathode materials La0.8Sr0.2MnO3 (LSM) and La1-xSrxCoyFe1-yO3 (LSCF) were grown as heteroepitaxial thin films on lattice matched single crystal substrates. Changes upon heating the films to operating temperature and pressures were characterized using various synchrotron x-ray techniques. Total Reflection X-ray Fluorescence (TXRF) measurements, which probe compositional changes, were made at high temperature in real time. The LSM surfaces were found to develop manganese enrichment when heated. Highly strontium doped LSCF were found to develop strontium-rich surfaces. HArd X-ray PhotoElectron Spectroscopy (HAXPES) was used to investigate the electronic structure of the materials. Highly strontium doped LSCF precipitates a surface strontium phase that contains both oxide and carbonate contributions.IntroductionSolid oxide fuel cells (SOFCs) are chemical to electrical energy conversion devices that could potentially reshape how energy demands are fulfilled. SOFCs have a potential efficiency over 70%, fuel flexibility, low emissions, and low degradation over long time scales. Commonly, SOFCs are operated at high temperatures (above 800°C). At these temperatures expensive housing is needed to contain an operating stack as well as coatings to contain the oxidation of the metallic interconnects. Lowering the temperature of an operating device would allow for more conventional materials to be used, thus lowering overall cost. Understanding the reaction kinetics of the oxygen reduction reaction at the surface of the cathode is vital to designing a system that will perform well at lower temperatures. A commercialization goal is to reduce operating temperatures without sacrificing performance.In order to exploit the advantages of SOFCs, an understanding is needed of the surface chemical states of cations on the surface of the cathode and how this relates to the oxygen reduction reaction (ORR):"

Jan 1, 2014

By Ulrich Benatzky

Rheinbraun AG, Germany, is the management company of the mining and raw materials division of RWE AG. Rheinbraun's core business and major functional area is opencast lignite mining in the Rhineland. The characteristic feature of opencast mining is continuous operation using bucket-wheel excavators, belt conveyors, and spreaders. The report gives a survey of the conveyor systems used. In addition to the general performance data of these belt conveyors, this report will deal in particular with major components, such as drive stations and individual mechanical components (e.g., conveyor belts, pulleys, gears, couplings, brakes, scrapers), as well as monitoring systems. Finally, an assessment of the conveyor systems, together with future developments, will be given.

Jan 1, 2000

By Dale S. Preece, Stephen H. Chung

Explosives energy can be used effectively in breaking and displacing large volumes of rock in mining and quarrying industries in both open pit and underground. The blast result, however, may not be economical if the applied explosives energy distribution is not properly applied to match a given set of geometries. However, this engineering problem can be resolved by using a modeling approach in the blast design process. Starting with a given set of blast design parameters that include explosive, elastic properties of rock, geometry of the blast pattern as well as the delay firing time, this paper shows how a discrete element blast model can be set up to allow the examination of the effect of critical design input parameters on blast results. Examples are given in this paper to help visualize the value and application of blast simulations. They are (1) regular and terrace bench blasting models for throw control, (2) underground blasting including a drop raise opening and (3) collapsing of a multiple room-pillar structure with proper firing sequence to control the mixing of blasted materials.

Jan 1, 2005

By Stanley Rajnak, John E. Dorn

The saddle-point activation energy for the nu-cleation of a pair of kinks is estimated as a function of the applied stress, the lattice constants, and the height and shape of the Peierls' hill by employing the line-energy model of a dislocation. The kinetics of disloration motion by the Peierls' mechanism are discussed and the microscopic dislocation velocities and macroscopic strain rates are formulated by the Arrkenius type of approach in terms of the activation energy for the formation of pairs of PEIERLS was the first to illustrate that a straight-dislocation line has its lowest energy when it lies in a potential valley parallel to lines of closest packing kinks. The log of the dislocation velocity is found to be approximately proportional to the log of the local applied stress. It is also shown that the low-temperature mechmical properties of several bcc metals might be explained in terms of the Peierls mechanism, good agreement being obtained between theory and experiment for the flow stress us ternperature, activation energy vs stress, and activation volume us stress curves for these metals. of atoms on the slip plane. When such a straight dislocation is moved rigidly from one valley toward the next, the atoms in the vicinity of the core of the dislocation change their positions and bond angles, causing the energy of the dislocation to increase. Midway between two adjacent valleys, the disloca-tion energy reaches a maximum value and any additional small displacement will cause the dislocation to fall down the hill into the next valley. The maximum shear stress necessary to promote such

Jan 1, 1964

By P. Falcão Neves

A detailed analysis of the geomechanical behaviour in rock cutting with a diamond saw is provided to obtain a better understanding of the mechanisms involved in the process. The energy of elastic deformation (before failure) and plastic deformation (post failure) was determined in uniaxial compression tests as well as the energy consumed per unit volume in the cutting process. The test samples are White and Ruivina marbles from Borba - Vila Viçosa in Portugal. Correlations between total deformation specific energy and cutting specific energy, normal and tangential forces and diamond indentation are analysed, and some conclusions are presented.

Jan 1, 2012