Search Documents

By E. Buehler, R. H. Willens

A Hew melting technique has hem adapted to the rapid quenching of- alloys from the liquid state. The inelting method has no limitations on the alloys investigated for there is no reaction with crucible materials and the most refractory materials are easily melted. The vate of heating is so rapid that alloys which have a high vapor pressure constituent can be melted with a minimal loss in material. Several new superconductovs have been discoveved by vapid quenching of lolten alloys. THE rapid quenching of alloys from the liquid state has led to the discovery of many new metastable phases. The methods initially used were limited to alloys which did not react with crucible materials.1,2 There was also the unmentioned limitation in tem- perature. Alloys with melting points much greater than 2000°C could not be melted in the rapid-quench apparatus. Recently, there have been successful attempts to rapidly quench reactive alloys by Moss et at. and Matthias Moss et al. injected powdered material (325 mesh) into a high-temperature plasma and the high-velocity molten droplets impinged on a cooled copper plate. The technique innovated by Matthias was to melt the alloy in an arc furnace and splatter it against a copper plate by means of a high-velocity gas jet aimed at the melt. I) FAST COOLING APPARATUS The creation of a metastable phase in a given alloy system by rapid cooling from the melt is contingent on the quenching rate. Some alloys require very slow rates while other alloys require the ultimate in quenching rate. At the present time, the vertical-gun technique of Duwez and willens' has demonstrated, in practice, the highest quenching rates and thus the best

Jan 1, 1967

By C. R. McClung

"Molybdenum, in the form of molybdenite, is a common byproduct of many copper mining and concentrating operations. Contrary to most copper sulfide minerals where recovery is principally liberation controlled, the recovery of molybdenite is much more complex with fully liberated particles commonly lost to tailings. It is this complexity that facilitated the necessity for a geometallurgical investigation of molybdenite from the Bingham Canyon deposit. The aim of this investigation was to determine the effect mineralogy and/or mineralogical attributes (i.e. morphology, angularity, liberation, size) have on the recovery of molybdenite in the processing circuit. A set of samples was collected from the ores and products produced by Rio Tinto Kennecott’s Copperton Concentrator. All samples were analyzed using normal polarized reflective light, Mineral Liberation Analyzer (MLA) and X-ray diffractometery (XRD) techniques. The results of this investigation revealed the presence of two distinctly different types of molybdenite, which have been identified as the two polytypes of molybdenite, i.e. hexagonal (2H) and rhombohedral (3R). The 2H polytype occurs as textbook-shaped particles in quartz-molybdenite veins that are located in the core of the Bingham Canyon deposit. The 3R polytype occurs as disseminated, “ball”-shaped particles with a dull or frosted appearance along the margins of the mineralized intrusive body or central core. Concerning their metallurgical behavior each type exhibits unique metallurgical properties that are consistent with those reported in the published literature. For instance, the 2H polytype is easily ground and kinetically “faster” floating with surface attributes that are amenable to higher rates of recovery. This commonly results in the production of a high quality molybdenum concentrate under normal operating conditions common to most copper concentration operations. In contrast, the 3R polytype is difficult to grind and kinetically “slower” floating with surface attributes that less amenable to recovery under normal operating conditions. Therefore, in deposits with higher concentrations of the 3R polytype, modifications to the normal operating parameters may be necessary to improve the recovery of molybdenum. Finally, a preliminary investigation into the metal budget of porphyry Cu and Mo deposits indicates that a positive correlation may exist between the total economic metal budget and the polytype content. For example, higher concentrations of the 3R polytype appear to be more prevalent in Au-enriched porphyries versus Mo-enriched porphyries. This observation may also serve to help explain why it is easier to obtain high rates of recovery in Mo ± W-rich deposits, which contain little to none of the 3R-polytype. Consequently, the potential for the metal budget of a porphyry deposit to be used as an indication of the molybdenite polytype present, as well as its impact on the economics (exploration) and/or on the processing circuit (plant design) could exist. In conclusion, this investigation highlights the necessity of understanding the mineralogical properties or characteristics of molybdenite and/or other economic mineral(s), as these can and will have a direct impact upon the performance and plant optimization."

Jan 1, 2016

By R. Holmwood, M. Faris, P. Holloway, M. Collins

Sulphuric acid addition is a major driver of the economics in the processing of nickel laterite ores by high pressure acid leaching (HPAL). Understanding the optimal acid addition rate is essential for the success of any HPAL operation, and this is especially true at Ambatovy, where the composition of the feed tends to vary significantly on a day-to-day basis. Most studies on the effect of acid on nickel extraction in HPAL have used laboratory testwork as their basis. Although these studies are invaluable in assessing the economics of a new project, they are limited by the range of ore composition that can be tested and the differences between the operation of the laboratory equipment and the commercial plant. To enable optimization of the acid addition at Ambatovy, operating data from the HPAL operation were obtained using OSISoft’s PI system and the data from several periods were examined to develop relationships between acid addition and nickel extraction. The initial relationships from 2014 focused on the acid required to achieve a target nickel extraction of 95%, with aluminum and magnesium in ore and feed slurry solids content as the major variables. As Ambatovy ramped up through 2015 and 2016, the calculated acid requirement was further refined to address the effects of HPAL temperature and retention time, and the oxidizing/reducing characteristics of the ore, and to generate acid requirement relationships as a function of ranges of nickel extraction. These relationships supported raising the target nickel extraction to 96% and enabled the development of an economic model between acid addition and nickel extraction.

Jan 1, 2017

By C. J. A. Mcewan, C. M. Rice

The Rosita Hills contain rich, vein- and breccia pipe-hosted precious metal deposits. Volcanic activity occurred in two cycles - an early, mainly andesitic cone-building phase that terminated in the formation of a caldera and breccia pipes and a later phase characterised by trachytic lavas and dykes, rhyolite domes and lamprophyre dykes. Alteration consists of weak propylitic and argillic and, locally, intense advanced argillic, K-feldspar sericitic and silicic types. Marked trace-element depletions (Rb, Sr, Zn, Mn) are associated with K-feldspar-sericitic alteration and with advanced argillic alterations, whereas enrichments (Pb, Ag) are associated with K-feldspar-sericitic alteration. Gold distribution is highly localised and is controlled by breccia pipes and a caldera ring fault; it is not related to district scale alteration. In general, the geochemical and alteration patterns are complex, but they are clearly influenced by linear structures, the caldera ring fault and breccia pipes. Pipe-hosted Au-Ag and vein-hosted Ag mineralisation are associated, respectively, with early andesitic and late, post-caldera rhyolitic activity. The pipe-hosted and, especially, the vein-hosted mineralisation show affinities with adularia-sericite-type epithermal deposits

Jan 1, 1991

By D. K. Chibwe, P. Taskinen

"This investigation consists of a numerical and physical modelling exercise on flow patterns, mixing, solid-liquid mass transfer, and slag-matte phase distribution in a 0.2-scale cold model of an industrial Peirce-Smith converter (PSC). Water, kerosene, air, and sintered benzoic acid compacts were used to simulate matte, slag, injected gas, and solid additions into the PSC. The 2D and 3D numerical simulations were carried out using volume of fluid (VOF) and realizable k-e (RKE) turbulence models to account for the multiphase and turbulence nature of the flow respectively. These models were implemented using the commercial computational fluid dynamics numerical code FLUENT.Numerical and physical simulations were able to predict, in agreement, the mixing and dispersion characteristics of the system in relation to various blowing conditions. Measurement of mass transfer indicated that fluid flow in the PSC is stratified. Blowing configurations and slag volume both had significant effects on mixing propagation, wave formation, and splashing.As a potential process alternative to increase conversion efficiency, we propose a combined blowing configuration using top lance and lateral nozzles. The numerical simulations were conducted on combined as well as lateral blowing conditions, and the results of the combined concept are encouraging."

Jan 1, 2015

By Lukasz Maciag, Ryszard Andrzej Kotlinski, Ryszard Krzysztof Borówka, Dominik Zawadzki

Concentration and composition of rare earth elements (REE) and major elements in the sediment samples from the IOM H11 Fe-Mn nodule deposit, eastern part of the Clarion-Clipperton nodule field (located between the Clarion-Clipperton Fracture Zone - CCFZ; tropical Pacific), have been studied. We show the controls on REE concentrations and described vertical/horizontal variability of selected metals in pelagic sediments from the CCFZ. According to Kato et al. (2011), who analyzed 2000 seafloor sediment samples at 78 sites of the Pacific Ocean, deep-sea mud shows high concentrations (2230 ppm maximum) of ?REY and could be potential resource of these elements in the future. However, our work does not fully confirm that sediments in the IOM H11 are significantly enriched in REE.

Sep 1, 2014

By N. Aarthi, G. R. Dodagoudar

The improvement of soft clay deposits using stone columns is a well-established ground improvement technique in the western world. This technique has been well documented and has proper design codes for precise execution in the field. The sand compaction pile (SCP) method is a contemporary technique to stone columns and has limited literature related to the strength characteristics of the loose to medium dense sand deposits treated with SCP. The available studies on the SCPs installed in cohesionless deposits focused on the improvement by indirectly assessing the SPT-N values pre- and post-installation of the SCPs. The widespread implementation of the SCP technique in recent years has increased the need for a more direct evaluation of the improvement. Earlier studies in this regard have revealed that the available design solutions are based on the type of installation equipment, their working efficiency, and accumulated field data. However, it is found that there are no generic design codes for the direct estimation of the ultimate bearing capacity of the SCP improved cohesionless deposits. To meet the design requirement for the SCP treated ground, a series of experimental and numerical investigations are performed in the present study to arrive at a direct framework in the form of design charts based on the pressure-settlement response of the treated ground. The developed design charts give the ultimate bearing capacity (UBC) of the treated sand deposit for the known initial relative density (RD) of the deposit, spacing and diameter of the SCPs, size of the footing, and for the specified target unit weight required for the intended application. It is concluded that the design charts will be of preliminary use to the design engineers to directly evaluate the UBC of the SCP improved loose to medium dense cohesionless deposits as part of the SCP method of ground improvement. It is expected to have more field-scale experiments and in-depth analysis before implementing these charts for actual field execution.

Nov 1, 2022

By F. Sillers, R. T. C. Rasmussen

"INTRODUCTION This is the fourth report of investigations dealing with the cooperative tests between the Bureau of Mines and industry on the use of electrolytic manganese in steelmaking. The first report dealt with the use of electrolytic manganese in the manufacture of stainless steel 3/ the second with its use in acid electric steel practice, 4/ and the third with its use in low-carbon basic open-hearth steelmaking. 2/ A résumé of those investigations E7 appeared in the magazine STEEL. 5/ The present report deals with the use of electrolytic manganese in the manufacture of four types of stainless steel and the new Timken 16-25-6 alloy. The Bureau of Mines supplied The Timken Roller Bearing Co. with 62,000 pounds of electrolytic manganese for use in the tests.The electrolytic manganese was produced at the Bureau of Mines pilot plant, Boulder City, Nev., by the process developed by the Bureau and described in Bulletin 463, Operation of Electrolytic Manganese Pilot Plant, Boulder City, Nev., by J. H. Jacobs. J. W. Hunter, W. H. Yarroll, P. E. Churchward, R. G. Knickerbocker, R. W. Lewis, H.A. Heller, and J. H. Linck. The workcarried out under the direction of R. S. Dean, formerly assistant director, Bureau of Mines, and R. G. Knickerbocker, formerly chief, metallurgical branch, as part of a long-range program involving the development, manufacture, and use of manganese from domestic ores. Preliminary arrangements for the plant tests were made by the late A. A. Dow. 7/"

Jun 1, 1947

By R. A. Franks, G. F. Friel, J. C. Edwards, L. Yuan

Two mine-fire experiments were conducted in the National Institute for Occupational Safety and Health's (NIOSH) Safety Research Coal Mine (SRCM) at the Pittsburgh Research Laboratory (PRL) which demonstrated that smoke from diesel-fuel fires of 500 kW and 660 kW heat-release rates in a return airway can develop, without causing a complete air flow reversal, into a roof layer that can migrate upwind forming a counter flow to the primary airflow in a crosscut. Subsequently, smoke can penetrate into an intake airway and create a hazardous atmosphere in the intake airway upwind from the fire. Visibility conditions less than 13 m were created by the smoke in the intake airway downwind from the crosscut. Modeling of the event with a three-dimensional, time-dependent, computational fluid dynamics (CFD) program correctly represented the smoke movement.

By M. E. Alam

In the present study, 1.1 volume percent of nano size copper was incorporated into pure tin using hybrid microwave sintering assisted powder metallurgy route. Microwave sintered samples were extruded both at room temperature and at 230 °C. Microstructural characterization studies were conducted on the extruded samples to investigate the distribution characteristics of secondary phase and grain morphology. Room temperature tensile test results revealed that hot extruded Sn-Cu samples exhibited higher strengths (~ 41%, in case of 0.2% yield strength and ~ 38%, in case of ultimate tensile strength) and ductility (~ 15%) when compared to room temperature extruded samples. On the contrary, the tensile properties of pure tin remained independent of extrusion temperature. An attempt is made in this study to correlate the effect of extrusion temperature on the microstructural evolution and tensile properties of Sn-Cu solder.

Jan 1, 2009

By J. B. Clark

In multiphase ternary diffusion studies, plots of the variation bf the composition on the isotherm constitutes one of the most effective methods of presenting experimental results, especially if such plots are made in a manner which relates the composition path on the isotherm with the diffusion layer structure in the couple. Unfortunately, if different conventions for plotting are used serious misinterpretations occur readily, causing apparent disagreement between investigators who actually share the same viewpoint. A common convention for mapping these diffusion paths is needed at this time because with the increasing use of the electron-probe X-ray microanalyzer, a much greater number of ternary diffusion studies can be expected in the near future. In an effort to prevent unnecessary confusion in the future litera- ture, a convention for these plots is proposed, as outlined below. A hypothetical example of the use of these conventions is given in Fig. 1 where the path of composition through the diffusion structure of the 100 pct A/50 pct B, 50 pct C couple is plotted on the appropriate isotherm of the ABC system. The lower case letters relate the region in the diffusion layer structure to the appropriate composition on the ternary isotherm. 1) The diffusion path is plotted on the isothermal section corresponding to the diffusion temperature of the couple. 2) The terminal compositions of the plotted diffusion path are the initial compositions of the couple halves—provided infinite boundary conditions are maintained. If, in either couple half, infinite conditions are not maintained, then the path terminates at the composition of the exterior surface of the couple. If, at this surface, the composition varies with time or if the plotted path is time dependent, then the diffusion time should be noted beside the plotted path. 3) A solid line crossing a single phase field (e.g., line a-b in Fig. 1) denotes an existing layer of that phase in the diffused couple. 4) A dashed line crossing a two-phase field parallel to the tie lines (e.g., line g-h) represents an interface between the two phases with interfacial compositions designated by the ends of the tie-line. The line represents no spatial extent. 5) A solid line crossing a two-phase field so as to cut tie lines (e.g., line b-c or line j-k) represents a locally equilibrated columnar two-phase layer. The solid line should cut those tie lines which correspond to the lateral interfacial equilibria along the columnar

Jan 1, 1963

By Francis D. Leathers

Four friction pile load test programs, including 23 tension tests and 9 compression tests, have been performed as part of the Central Artery/Tunnel Project in Boston, Massachusetts. The tests, performed on both precast, prestressed concrete (PPC) piles and steel piles, yielded the following adhesion values: [Soil Type Clay Clay Glacial Till Interbedded Sand and Clay Interbedded Sand and Clay Pile Type PPC Steel Steel Steel PPC Adhesion (psf) 610 to 1,200 230 to 900 220 to 550 680 1,280 ] The adhesion appears to be affected by differences in pile material type, with PPC piles having higher adhesion than steel piles. However, part of the apparent difference for the clay may be due to differences in time between driving and testing. The significant range of test data means that the need for site specific testing to determine or verify design values of adhesion should be considered during design. Creep rates at loads near failure ranged from about 0.02 to 0.18 inches per log cycle of time, with most values in the range of about 0.04 to 0.08 inches per log cycle of time.

Jan 1, 1994

By Adam Turcotte

Mining operations consume a considerable amount of energy, and while reduced energy consumption is desirable, it is not always clear how to achieve this goal. Understanding the opportunities to optimize energy consumption is crucial, and the key to understanding is visualization. One option is the Sankey diagram, which has been used for over 100 years to visualize the flow of energy, materials, or cost through various processes. However, there are drawbacks to this approach that must be addressed. In a Sankey diagram, each flow is represented by an arrow possessing a width proportional to the magnitude of the flow it represents. The diagrams show input flows, how energy is converted and into what form, and also output flows. As per the first law of thermodynamics, the total energy output is equivalent to the total energy input, so any energy that is not transferred to another process is considered to be wasted. These waste flows are depicted in Sankey diagrams and make it straightforward to associate energy sources, sinks and waste flows. Unfortunately, Sankey diagrams do not convey all information required to support practical decision making for redirecting individual energy flows. Based only on a Sankey diagram, it may become evident that a significant flow of waste heat is of the appropriate grade (temperature) and volume to meet an on-site heat demand currently being met with paid-for, possibly carbon intensive fuel. However without augmenting the Sankey diagram with 3D spatial, true geometric analysis, the practicalities of the concept or idea may not be fully appreciated. Another issue with a Sankey diagram is that the magnitude of the energy flowing between processes may have temporal fluctuation or variability on different timescales (diurnal, seasonal, interannual). Currently, Sankey diagrams only provide a static picture of energy conversion and consumption, so that, for example, 4 separate diagrams could have to be prepared for each season. A new energy flow visualization technique which we have called Sankey Trees has been developed. Process locations are defined within a 3D model of the site being studied, and the magnitude of the flow between each pair of processes considered is replaced with a time series. Branches of sustained and diminishing flows are represented through variation of the geometric properties of the branches of the trees. These branches are animated to indicate the direction of flow, and branch joints are used to indicate that a process is transporting one form of energy to multiple processes.

Aug 1, 2013

By J. Bouchard, M. Levesque, D. Georges-Filteau, P. Radziszewski, G. LeBlanc

"Grinding mills are infamous for their extremely low energy efficiency. This paper reports the results of an investigation that characterized energy outputs in industrial grinding mill circuits. It identifies and discusses the potential for recovering energy from grinding circuits. Agnico-Eagle Goldex Division, Mine Canadian Malartic, and New Gold New Afton Mine participated in the study by providing operating data for three semi-autogenous grinding mills and four ball mills. Results showed that on average, 79% of the supplied electrical energy was converted to heat absorbed by the slurry, 8% was lost through the drive system, and approximately 2% was transmitted to the ambient air. Only 9% of the input energy was actually used for grinding. The remaining 91%—wasted as heat—could potentially be recovered using suitable technologies or integrated energy management systems. This topic remains to be further investigated. ¦ KEYWORDS Comminution processes, Energy recovery potential, Grinding mills RÉSUMÉ Les broyeurs sont tristement célèbres pour leur rendement énergétique médiocre. Cet article présente les résultats d’une étude qui caractérise les rendements énergétiques des circuits industriels de broyage et examine les possibilités de récupération d’énergie dans les circuits de broyage. La mine Goldex d’Agnico Eagle, Mine Canadian Malartic et la mine New Afton de New Gold ont participé à l’étude en fournissant des données de fonctionnement pour trois broyeurs semi-autogènes et quatre broyeurs à boulets. Les résultats montrent qu’en moyenne 79 % de l’énergie électrique fournie sont convertis en chaleur absorbée par la pulpe, 8 % sont perdus dans le système d’entraînement et environ 2 % sont dispersés dans l’air ambiant. Seuls 9 % de l’énergie primaire sont, de fait, utilisés pour le broyage ; les 91 % restants (perdus sous forme de chaleur) peuvent potentiellement être récupérés à l’aide de technologies adaptées ou intégrées dans des systèmes de gestion de l’énergie. Cette question demeure toutefois ouverte. ¦ MOTS CLÉS broyeurs, potentiel de récupération de l’énergie, procédés de comminution INTRODUCTION Grinding is largely recognized as a very inefficient process; energy efficiency estimates range from < 1 to 2% (Fuerstenau & Abouzeid, 2002; Tromans & Meech, 2002, 2004) when comparing the input energy to that required for generating new mineral surfaces. Criticizing an “ill definition of the reference for the output energy,” Fuerstenau and Abouzeid (2002) proposed a “more meaningful baseline” would be “the energy for producing new surface area by the ¬mens.” Based on this reference, they concluded that “the ball mill is reasonably efficient energetically,” exhibiting an efficiency of approximately 15% for quartz."

Jan 1, 2019

By Scott Thayer, Michael Murphy, Natalie Cope, Gabriel Esterhuizen, Anthony Iannacchione, Tim Miller, Brent Slaker

"The Subtropolis room-and-pillar mine extracts the Vanport Limestone (Allegheny Formation, Pennsylvanian System) near Petersburg, Ohio. Strata instability problems associated with excessive concentrations of lateral stress caused the mine operator to implement a change in layout design. This mining method has been identified as a stress control layout, which has been used by other underground stone mines in the past with varying degrees of success. Practical experience has shown that entry headings advance in the direction of the principal lateral stress, producing lower stress concentrations with better mining conditions. It is important to minimize stress concentrations along the mining front, so an arrow-shaped advance is recommended. This technique advances more developments (headings) in a “good” direction and reduces developments (crosscuts) in a “bad” direction. As is expected, the stress control layout enhances the potential for shear failures in crosscuts. It is, therefore, important to focus crosscut engineering interventions that either: (a) lower stress concentrations (for example, an arched roof) or (b) enhance strength of the strata containing the shears (for example, rock reinforcement). This study focuses on observing strata conditions on a regular basis and monitoring the response of this strata to changing geologic and mining conditions through 3D Dynamic LiDAR scans.INTRODUCTIONProject AimsThe Subtropolis Mine is extracting the Vanport Limestone in northeastern Ohio. Since the start of mining in 2006, ground conditions have been significantly affected by excessive lateral stress condition. In some other mining districts with this hazard, certain mine layouts have been shown to lessen the potential for unstable ground conditions. The term “lessen” is used to state the realization that stress concentrations are not eliminated but instead occur in less frequency and intensity, and their locations can be projected.The stress-control mine layout, specifically for large-opening room-and-pillar stone mines, naturally evolved at mines suffering from excessive lateral stress problems. These mines will typically experiment with methods to mitigate adverse impacts, thus developing best practices for their conditions. These practices have evolved into a basic framework for the stress control mine layout. For example, Jack Parker was able to write about personal experiences at the White Pine Mine in Michigan (Parker, 1966, 1973). Various researchers at the U.S. Bureau of Mines (USBM), the Mine Safety and Health Administration (MSHA), and the National Institute for Occupational Safety and Health (NIOSH) have studied the effectiveness of stress-control mine layouts over a wide range of geologic conditions (Emery, 1964; Mark and Mucho, 1994; Iannacchione et al., 2003). While the stress control layout design approach has proven successful in many categories, it can be difficult to implement. For example, excessive stress conditions in crosscuts can put the ground control focused intervention at odds with ventilation and haulage constraints, thus limiting optimal crosscut size, shape, and location. Therefore, more information on the effectiveness of this approach is needed."

Jan 1, 2019

By M. Ge, C. Mborah

"The acoustic emission/microseismic monitoring (AE/MS) technique has widely been used in the mining environment for the monitoring of rock mass stability. A successful implementation of the method is hinged on being able to accurately determine the P- or S-wave arrival which is then used in the determination of the source of an event. Determination of the arrival phase is usually performed visually by a human expert. However, the mining environment is characterized by high noise levels and different noise types of varying intensities. Therefore, performing manual phase picking on time series data acquired from the AE/MS monitoring system can sometimes be tedious and time consuming if not impossible. In this paper, a proposal for improving manual P-wave phase arrival picks is discussed. The method involves the filtering of the AE/MS data using a stationary discrete wavelet transform (SDWT) method. After filtering, appropriate scales/levels of the multi-level decomposition process are then selected for further processing. The first step in the picking process after filtering, requires the computation of the signal power and the root mean square (RMS) using the signal amplitudes at each scale. The preliminary P-phase arrival time is picked using the results of the calculated power and RMS values respectively. The calculated RMS values are then superimposed on the calculated power values to determine the final arrival picks. If the arrival time picks obtained by both methods coincide or are within 5 to 10 sample points, the pick is considered reliable. The accuracy of the method was verified using AE/MS data from two datasets obtained from two separate underground mines. The results of the study showed that the picking method is reliable and robust. Based on the data studied, it can be concluded that the method will help reduce the time usually spent in processing AE/MS data from mines. INTRODUCTION A successful identification and location of the source of acoustic emission/microseismic (AE/MS) events is mainly dependent on the onset time of the P-wave phase. In many seismic networks, initial picks are performed by picking algorithms followed by manual picks by human experts. If the waveform signal-to-noise ratio (SNR) is low, the P-wave onset time picks by the human expert is generally reliable and accurate [1]. However, for waveforms with high SNR, picking of the P-wave onset could be a major challenge. Also, due to the volume of data acquired daily, manual processing could be stressful and time consuming [2]. These challenges continue to provide motivation for alternative means of providing reliable and efficient ways of improving manual phase picking. The AE/MS technique has been an intergral part of safety monitoring in mines [3] due to its capacity to identify zones of instability in a monitoring area. To obtain an accurate source of an AE/MS event however depends on the quality of the data used for P-wave phase picking [4, 5]. AE/MS data from mines are generally contaminated with excessive background noise generated by the different mining operations. The AE/MS signals of interest are mostly buried in background noise which makes it difficult to pick the P-wave phase arrivals [4]. Processing AE/MS data acquired in noisy environment remains a major challenge due to the weak nature of AE/MS signals [6]. As noted by [4] most of the data recorded in the mine environment are mainly due to events not related to AE/MS events of interest. The complexity of data in this type of environment makes the detection and picking of P-wave arrival by human experts a very difficult task."

Jan 1, 2017

By F Jullian, L Jofre

Many maintenance managers find it difficult to justify investments in maintenance improvement initiatives. In part, this is due to a tendency by mine managers to regard maintenance purely as a cost centre, and not as a process able to influence productive capacity and profit. It is also hindered by a lack of alignment between commonly used maintenance performance measures and key business drivers, and the lack of formal business training amongst maintenance professionals. With this in mind, a model to assist maintenance managers in evaluating the benefits of maintenance improvement projects was recently formulated. The model considers four cost saving dimensions. These are: 1. reduction in the cost of unplanned repairs and maintenance,2. increased or accelerated production and/or sales,3. spares inventory reduction, and4. reduction in over-investment in physical assets and operating costs. This paper discusses the application of this model and a number of numerical examples are given to justify investments in maintenance improvement projects having varying objectives.

Jan 1, 2006

By J. J. Jonas, G. R. Stewart, A. M. Elwazri

Two important parameters for dynamic recrystallization can be derived from the changes in the strain hardening rate: the critical strain for initiation of dynamic recrystallization and the point of maximum softening. In this work, these values are determined from the flow stress-strain data obtained in continuous compression testing in the range 900-1100°C. The resulting strains are used to calculate a kinetic model of dynamic recrystallization for two materials: 304 austenitic stainless steel and a hypereutectoid plain carbon steel. The mechanical parameters used to define the proposed model are confirmed with quantitative metallographic analysis of the recrystallized microstructure.

Jan 1, 2004

By B Flynn, P Knights

Low-loaders or &apos;floats&apos; for relocating equipment in surface mines are limited to a capacity of approximately 350 t. In the iron ore industry it is desirable to be able to rapidly relocate excavators in order to maintain production rates within appropriate quality limits. In addition, the ability to rapidly relocate heavy equipment raises the possibility of improving the quality of repairs by performing maintenance in controlled shop conditions. However, many iron ore operations operate hydraulic excavators in the 600 to 800 t range, with newly released excavator models exceeding 800 t. These excavators are too large to float using conventional technology. This paper examines the potential for using multi-bogie transporters to relocate large hydraulic excavators in surface mines. Recent innovations have seen the development of modular transporters which can be coupled together to achieve larger platform areas. When separated, and with their drive bogies neutralised, these units are able to be towed behind prime movers and relocated between mines via public roads. The potential cost savings for relocating a Terex RH170 excavator in an open pit coal mine are examined. In the first six months of 2008, the analysis showed the potential for a 38 per cent reduction in total travel time with a corresponding revenue increase of approximately $350 k. The paper recommends that a feasibility study be conducted into offering a heavy equipment relocation service within the Pilbara region.

Jan 1, 2009

By B. Listerud, G. Zhan, M. A. Jones

Barrick Goldstrike Mines Inc. (BGMI) operates the Betze-Post openpit and the Meikle and Rodeo underground mines. Because the majority of the orebody is located below the water table, mining at BGMI requires a significant dewatering program. BGMI has a comprehensive dewatering and water management system that experienced a peak dewatering rate of 4,400 L/s in the mid 1990s. Changes to the hydrologic/hydrogeologic system caused by the mine dewatering have been monitored by an extensive network of groundwater monitoring wells and surface water monitoring stations, which cover about 1,550 km2. In addition to the monitoring program, a new tool, called Interferometric Synthetic Aperture Radar (InSAR), has also been used to enhance the evaluation of changes. Finally, a groundwater flow model has been developed that successfully simulates and predicts aquifer responses in the mine area and region. The well-calibrated flow model has served as a reliable tool to develop dewatering and mining plans, and project post-closure hydrologic conditions in the region. This paper introduces the BGMI dewatering and water management system and the means used by BGMI to evaluate and anticipate hydrologic responses in the region. The water management and analysis system has been and continues to be an integral part of managing ongoing operations, planning and pricing out future activities and evaluating the long-term effects of mine water handling.

Jan 1, 2011