Search Documents

By Thomas Mütze, Michael Klichowicz, Mathis Reichert, Holger Lieberwirth

"Self-similarity is proofed to be a common feature when brittle material is comminuted, either in particle bed or single particle mode. Appropriate test work is well documented for particle sizes less than 7 mm in several publications. In contrast, almost no research has been done for coarser particles. The aim of this paper is to show that the fracture pattern of coarser material also tends to be self-similar. Hence, single particles of quartzite, granodiorite and dolomite were comminuted under compressive load. The focus was set on three different size fractions -3.15 +2.5 mm, -31.5 +25 mm and lumps -300 mm. According to the wide range of particle sizes, three different piston-die presses were used with a maximum compressive force ranging from 5 kN to 4000 kN. The force-displacement curves were recorded in order to calculate the specific comminution energy. Additionally, the -31.5 +25 mm size fraction was crushed in a laboratory scale jaw crusher and a roll crusher. Some authors report that the energy-size-reduction relationship of self-similar materials can be approximated by a linear function, which is independent of the comminution equipment. In their charts the slope can be seen as a product-size-independent grindability measure. Our tests show a self-similar breakage behavior when particles in a range of -300 +3 mm are comminuted in single particle mode. Furthermore, the products of the piston-die-presses and the roll crusher are similar to each other in a self-similar representation of the particle size distribution. The jaw crusher product, however, is not self-similar compared to the piston-die-press products. Finally, the linear energy-size-reduction relationships are confirmed for each fraction, but show size dependent slopes."

Jan 1, 2014

By A G. Dempster, N Barnett, J Oh, S Saydam

NASA’s Artemis III mission is expected to return astronauts to the surface to explore and sample the lunar volatiles by 2026. These volatiles are anticipated to provide scientific insights as to how the Moon was created and economic value to off-Earth operations. These same volatiles can pose health implications to astronauts and Earth based personnel handling lunar regolith samples. Using Australian, USA and NASA airborne contaminant exposure limits and the Lunar CRater Observation and Sensing Satellite (LCROSS) measurements of lunar volatiles in the Cabeus crater ejecta, the minimum mass of lunar regolith that can be safely handled by humans on Earth and in spacecraft can be calculated. This analysis determined a 0.15 grams pure sample of Cabeus crater regolith within a cubic metre of air has enough volatiles to exceed safe working conditions, and 14.9 grams of pure Cabeus crater regolith per cubic metre of air can impact human life. The intent of this analysis is to assist safe handling and exposure calculations for the safe handling procedures of lunar regolith containing volatiles.

Sep 1, 2024

By Leonard P. Vitt

This report details the work done to provide the U.S. Bureau of Mines with a customized Wireless Ground Monitor Wireless Ground Monitor was modified as follows: 1. A voltage regulator was added to prevent false trips with line voltage variations. 2. A Ground Wire Trap was designed to eliminate problems with parallel paths and provide spark suppression. 3. A three phase filter was designed to reduce 60 Hz leakage current. 4. A portable tester was designed to permit complete test of installed systems. 5. The design was modified to insure trip with an open ground wire in the event of a failure of any one semi-conductor component.

Jan 1, 1976

By E. D. Slone, F. L. Dillard

When a new mine is in the planning stages, one of the most important decisions to be made is the selection of' face haulage equipment and the interrelated transportation system to the surface. Equally important is the method of transporting personnel supplies and repair parts from the surface to the working places. When Bell & Zoller management elected to open the new Zeigler mine in the No. 9 seam near Madisonville, Ky., last year, various transportation systems were considered. It was agreed early that a slope mine would be preferred to a shaft mine, and that belt conveyors would be more economical than a rail system.

Jan 1, 1970

By AIME AIME

WTHIN the next month all members of the Institute will be given an opportunity to vote for a new President, two Vice-Presidents, and five Directors. All of the candidates nominated by the official committee are well known to certain groups of the Institute membership but a brief record of their professional lives will be given here for the information of those that will vote. Not since 1927, when Everette DeGolyer guided the destinies of the Institute, has a member of the Petroleum Division been a candidate for President. John Meston Lovejoy has been a Director since 1930, and a Vice-President as well for the last year: In the three years 1932-4 lie was also chairman of the Admissions Committee. Dir. Lovejoy graduated from the Columbia School of Mines in 1911, just before lie was 22 years old, and began his professional career as a copper miner at Chuquicamata. Chile. Silver and gold mining later claimed his % attention, and it was not until 1914 that lie gut into the oil business, as geologist for the Standard Oil Co. of N. Y. This took hint to China and he later worked for the company in Wyoming. In 1917 lie joined the Army where lie rose to be captain of Field Artillery. Upon his return to the United States he went to work for the Amerada Petroleum Co., of which he later became vice-president and general manager, with headquarters in Tulsa. Since coining to New York he has been president of the Petroleum Bond & Share Cu.. and is currently president of the Seaboard Oil Co.

Jan 1, 1935

By L. L. Oden

The purpose of this research was to develop a method to remove copper and tin from the magnetic fraction of incinerated municipal refuse, as recovered by the Bureau of Mines pilot plant in College Park, Md. Copper, present in the scrap in a metallic form bonded to ferrous objects, was amenable to leaching in cupric ammonium carbonate solution. Copper levels in small 5-to 10-lb lots of treated scrap were reduced from the initial level, 0.5 to 0.6 pct, to 0.1 to 0.2 pct. Larger lots of scrap (100 lb) were treated less effectively because of poor contact of solution and scrap. Oxidation in the air or in aerated aqueous solution was applied to liberate tin from the dilute solid solution present on the surface of incinerated tinplate. Shredding of air-oxidized scrap or caustic leaching of scrap oxidized in solution reduced tin levels from the initial 0.25-pct level to about 0.1 pct.

Jan 1, 1973

By Heithecker R. E.

In June 1933 the Bureau of Mines, in cooperation with the State of Oklahoma and the Oklahoma City Chamber of Commerce,, published a report of the gas reserves in the Oklahoma City oil field3/ based upon data as of October 1932, at which time there were 43 classified gas wells in the field, The estimates were obtained by the ?porosity-area" method. There are two general methods of estimating natural-gas reserves. The porosity-area method, as used by Hill and Rawlins, is used when a gas field is comparatively new but after enough drilling has been done to determine the average thickness, porosity, and areal extent of the producing horizon. The "pressure-volume? method of estimating gas reserves, the method used in this report, may be used after a sufficient volume of gas has bean withdrawn from the reservoir to cause an appreciable decline in reservoir pressure.

Jan 1, 1937

By Steve Kral

MINExpo INTERNATIONL 2000 was a good place for companies to introduce new products, technologies and services to the mining industry. Caterpillar took that a step further. The company hosted a one-day preview of its mining products at its Tinaja Hills Training and Demonstration Center near Tucson, AZ. About 30 members of the trade press spent the day at Tinaja Hills before heading on to Las Vegas for MINExpo INTERNATIONAL 2000. Dozens of Caterpillar professionals provided the editors with a first-hand look at Caterpillar’s mining trucks, loaders, excavators, road graders, water trucks and engines. In addition, these Cat experts explained the intricacies of each piece of equipment, the latest technology that led their improvement and their value to the company’s mining customers.

Jan 1, 2000

Spirals have become one of the most popular methods for treating fine coal. Unfortunately, spirals tend to produce an undesirably high specific gravity cut-point and often misplace significant amounts of coal and/or rock. In the present study, a process-engineering tool known as linear circuit analysis was used to identify problems with traditional spiral circuits and to suggest alternative configurations. These analyses indicate that a modified rougher-cleaner circuit incorporating a middlings recycle stream offers the best option for improving performance while maintaining a reasonable circulating load. In light of this finding, a full-scale test circuit was installed and evaluated at an existing preparation plant. Data obtained from the plant tests indicate that the new spiral circuit can simultaneously reduce cut-point and improve separation efficiency. Preliminary economic analyses show that the new circuit provides an attractive payback on the capital investment.

Jan 1, 1998

By William H. King

Preliminary examination of the Virgin River manganese deposit was made by C. H. Johnson, Bureau of Mines engineer, in March 1941. During, April and May 8 trenches were dug, a 48-foot inclined shaft was sunk, and 719 linear feet of channel samples were cut. McKelvey and Wiese, of the Federal Geological Survey, completed mapping the deposit, including the entire area of overlying formations comprising the point of land between the outcrop and Lake Mead. The geologic maps, maps, and ore estimates resulting from these examinations formed the basis for a preliminary report by C. H. Johnson, who recommended further exploration by diamond drilling.

Jan 1, 1949

By R. J. Leary

A small electronic digital computer employing punched cards has been used to facilitate the solution of a variety of problems in Bureau of Mines pyrometallurgical research. In this work the computer has been found to be economical for solving both simple problems that occur repeatedly and those involving complex or iterative calculations. Each of these classes of problems and their respective solutions are described. These small computers can be used effectively by researchers when they work in consultation with a computer specialist. Close team work produces the required solutions in less time, and, oftentimes, in a more useful form. Participation in programming by researchers develops in them a skill for evaluating the suitability of problems for electronic computing.

Jan 1, 1960

By S. K. Kawatra

In order to meet federal air pollution guidelines, it is necessary to remove a considerable quantity of sulfur from many North American coals. This may be accomplished by oxidizing the sulfur to water soluble forms, followed by washing the coal. Selective oxidation of the various sulfur forms can be accomplished through the use of a variety of types of bacteria. In this paper, the various bacteria and their requirements are described, and processes using bacteria to remove coal sulfur are discussed.

Jan 1, 1987

By R. F. Hadley

Alluvial valley floors constitute a valuable land resource and have been important to ranching operations in semiarid western United States. This resource may be in jeopardy locally if the alluvial deposits are disturbed by surface mining of coal deposits. Erosion problems caused by poor land-use practices can cause trenching of the unconsolidated alluvium with a consequent lowering of the water table and depletion of soil moisture needed to support vegetation. Historical evidence of this sequence of events is abundant in geologic literature and serves as the basis for assessing potential impacts of surface mining. The potential geomorphic impacts of surface mining on alluvial valley floors with regard to fluvial processes are: (1) disruption of the longitudinal profile followed by valley trenching and high sediment yields downstream and (2) replacement of the excavated alluvium with unconsolidated material that does not have similar physical characteristics and may be susceptible to erosion. Mining may disrupt the existing hydrologic framework affecting streamflow, ground-water levels and water quality of both surface water and ground water. Although functional hydrologic and geomorphic processes are similar, each valley represents a complex environment that does not submit to broad generalizations.

Jan 1, 1978

By R W. Shaw

The MTM Process targets treating lower grade and/or problem concentrates that are not attractive to smelters. The process has been developed at laboratory scale for copper and is based on a related development for zinc that has been extensively developed both in the laboratory and through pilot testing. The basis of the process is novel ammonia-ammonium chloride leach chemistry adapted to give high copper extraction whilst being selective over iron, arsenic and many other elements. The preferred flow sheet depends on location, especially infrastructure and utilities. These impact upon the leach and crystallisation stages more than copper reduction.

Aug 24, 2022

By R. E. Heithecker

In June 1933 the Bureau of Mines, in cooperation with the State of Oklahoma and the Oklahoma City Chamber of Commerce, published a report of the gas at reserves in the Oklahoma City oil field3/ based upon data as of October 1932, at which time there were 43 classified gas wells in the field, The estimates were obtained by the ?porosity-area" method. There are two general methods of estimating natural-gas reserves. The porosity-area method, as used by Hill and Rawlins, is used when a gas field is comparatively new but after enough drilling has been done to determine the average thickness, porosity, and areal extent of the producing horizon. The "pressure-volume? method of estimating gas reserves, the method used in this report, nay be used after a sufficient volume of gas has bean withdrawn from the reservoir to cause an appreciable decline in reservoir pressure.

Jan 1, 1937

By NIM REPORTS

Notices CONFRRENCE ON COMPUTRRS IN ENGINEERING The above Conference, which is being organized by the Electrical and Electronics Board of the Institution of Engineer!!, Australia, ill to be held in Sydney on 16th and 17th May, 1974. It is being planned in conjunction with the Sixth Australian Computer Conference and will be held during the week immediately preceding the latter. NIM REPORTS Report No. 1495 A method for the determination of ekmental sulphur on the surface of sulphide minerals. Report No. 1500 The chromatographic separation and determination of nobk metals in matte-leach residues. Report No. 1505 The production of the refractory aluminium saicates, with special refererence to South Africa. Report No. 1517 Computer-controlled flotation plants in Canada and Finland. Report No. 1526 Heat of solution as a control of aqueous-ammonia concentration. Report No. 1529 South African costs of equipment for the metallurgical industry (197).

Jan 9, 1973

By M. J. Beus, B. Stewart, S. Iverson

Synopsis U.S. Mine Safety and Health Administration (MSHA) accidents statistics have identified ore-pass hazards as a significant safety problem in U.S. underground metal mines. The statistics show that nearly 75% of injuries are directly or indirectly related to pulling or freeing of ore-pass chutes, the use of hand tools in ore passes, fails of broken rock in ore passes and structural failures of chutes or gates and ore-pass walls. Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) are investigating hazards in and around ore passes in hard rock mines. Risk assessment methods, such as fault-tree analysis, have been employed to identify the most probable causes of orepass failures, define research priorities and analyse the factors that result in malfunctioning and unsafe ore passes. Static and dynamic loads are being measured in a laboratory setting with the use of a reduced-scale orepass mock-up. Field tests are being initiated in mine ore passes to determine static and dynamic loads. Data from the test ore passes are being compared with data from the mine to characterize true system behaviour. Computer modelling with the use of closed-form solutions, finite-element analyses and a newly developed particle flow code predicts static and dynamic leads from the flow and the impact of ore and waste in the ore pass. Preliminary results indicate that dynamic impacts from ore and waste rock might be considerably greater than expected. The total static load is substantially less than is typically used fur the structural design of chute and gate support members. It is suggested that damping factors, normal and shear stiffness and mass frictional characteristics have a significant effect on particle flow and resulting impact loads. This is being verified with the use of results from laboratory tests, field tests and particle flow analyses. Ore passes are vertical or steeply inclined openings in a rock mass through which ore and waste are transported and where they mar also be stored. A typical underground mining system is shown in Fig. 1. The arrows indicate the locations of ore passes and loading pockets and their relative configurations. The control of material flow is potentially one of the most hazardous operations in underground mining. According to MSHA data. most of the ore pass-related accidents in the U.S.A. are associated with the loading-unloading cycle and removal of blockages from ore passes. In particular, attempts to free ore hang-ups have resulted in multiple fatalities. The hazards are obvious; there is uncertainty as to when the ore will break loose and miners are unable to escape falling rock to a safe location. Although ore passes and chutes and gate systems for underground metal and non-metal mines roust meet the requirements specified in the U.S. Code of Federal Regulations (CFR). Parts 57 and 75, recent structural failures of ore-pass linings and gates have underlined the lack of adequate ore-pass design standards available to both MSHA enforcement staff and mine engineers. Because of the importance of an ore pass to the safe operation of a mine design criteria need to be assessed and new guidelines developed. Researchers at the Spokane Research Laboratory of the Nationals Institute for Occupational Safety and Health (NIOSH) are investigating hazards in and around ore passes in hard rock mines and studying design criteria for ore passes. The near-term goal is to conduct laboratory and field experiments and computer modelling to evaluate the ore-pass design criteria currently used. Literature searches, field site

By N. Mejia, Z. Xiao, D. Fragomini, A. R. Laplante

"The adaptation to platinum-group minerals (PGMs) of a protocol developed to predict gold recovery by gravity is presented. The protocol is based on three different data sets: ore characterization of gravity-recoverable minerals, description of their behaviour in cyclones and ball mills, and performance of recovery units. Examples of these are given. It is shown that the gravity-recoverable PGM (GRPGM) content can be very high. A case study at the Clarabelle mill is presented. Sperrylite is the dominant platinum mineral, and its partition curve is very similar to that of gold, despite its lower density. Its grinding kinetics is significantly higher than for gold. As a result, sperrylite accumulates in finer sizes than native gold, but can still be recovered by gravity or flash flotation. Recovery projections based on gravity recoverable data are presented.BACKGROUNDReliable modeling of gold recovery by gravity or flash flotation from a grinding circuit is based on the ability to describe the properties of gold-bearing particles in the ore, their behaviour in grinding and classification units and the performance of the equipment used for recovery, be it gravity or flotation. This is shown in Figure 1."

Jan 1, 2004

By J. J. C. Heynike

The relationship between population growth and steel consumption since the beginning of the twentieth century is indicated, reference being made to the increasing capacity of production units and the resultant increased pollution in the same area. The need for the control of fugitive emissions with its associated high cost is pointed out. There is a direct relationship between energy and pollution, and examples are given of several improvements that have been made to achieve better energy usage and reduced pollution. Several practical examples of air-pollution control systems are described as applicable to the main metallurgical steel processes of today. In conclusion, reference is made to the fact that, with the improvements attained in reducing pollution, the public will not tolerate a decline in the standards already attained. Environmental control and better energy utilization will continue to be important aspects of steel-plant design and operation.

Jan 1, 1978

By S. Hosseinpour

Chromate conversion coatings (CCCs) are usually applied to these alloys to enhance their resistance to localized corrosion and to improve paint adhesion. The special properties of these coatings such as their low electrical contact resistance (ECR) make them suitable for satellites. This study is aimed to develop advanced CCCs with the proper appearance, morphologies and surface roughness and to evaluate their role on the ECR and thermo physical properties on hardened aluminium alloy of Alclad-7075-T6. Coating characterization was performed by means of scanning electron microscope (SEM) and atomic force microscope (AFM). ECR of coatings were measured by special laboratory designed instrument and a and c were measured by Emissometer and Reflectometer respectively. In addition, corrosion performance of the CCC-coated alloys was determined by 168 hr exposing to salt-spray testing in accordance with ASTM-B117. The results of accomplished experiments on the developed CCCs in this study have been agreeable concerning available acceptability criteria for satellite surfaces.

Jan 1, 2007