Search Documents

By W. A. Selvig

The experiments described herein were made at the request of Committee D-5, on Coal and Coke, American is n Society for Testing Materials, in order to obtain data as to the probable contamination of laboratory samples of coke Then pulverized to pass a No. 63 sieve of tine U. S. Standard Sieve Series2 by methods other than by ball-mills or hard-steel diamond mortars, which methods are specified-in the standard methods of that Society.3 After pulverizing, representative samples were analyzed by the Bureau of Mines at Pittsburgh for ash content to detect any contamination of the samples by the pulverizing apparatus. Preparation of Core Samples for Tests. Two samples of 48-hour beehive coke (Continental and Leisenring) made from Pittsburgh coal were selected for the tests. These cokes were crushed approximately to No. 10 sieve size, by first passing through a jaw crusher and then through a, roll crusher. The crushed coke was then carefully mixed and riffled into portions of about 800 grams each, and sent to three cooperating laboratories for grinding, through a No. 60 sieve. Size tests on these samples shoved the fineness to be as follows: [ ]

Jan 1, 1925

By D. Yu, T. A. Utigard, M. Barati

"Sulfation roasting of nickel concentrate to generate water-soluble metal sulfates was investigated as an alternative process to smelting for the recovery of valuable metals. The kinetics of dissolution of various species of the calcine in three leachants was studied; hot water, dilute HCl, and concentrated HCl. The results indicated that dissolution of sulfates by hot water at 90 ºC is achieved within 30 minutes. In order to increase the recovery of the valuable metals, acid leaching is necessary due to the existence of ferrite in the calcine.INTRODUCTIONInvestigations on the sulfation roasting of nickeliferous sulfide ores or concentrates were mainly carried out in 1950’s to 1990’s to generate water soluble non-ferrous metal sulfates followed by metal recovery by leaching (Stephens, 1953; Thornhill, 1954, 1961; Fletcher and Shelef, 1964a, 1964b; Fletcher and Hester, 1964; Frankiewicz, 1977; Norrgran, 1983). Commercialization of the sulfation roasting process was only performed by Falconbridge Ltd. (Thornhill, 1961; Boldt, 1967), which employed a sulfation roast process on nickeliferous pyrrhotite at 680 oC where Ni, Cu, and Co were leached and Fe2O3 was produced for the iron industry. In 1965, 118,342 tons of pyrrhotite was processed, however because of the huge SO2 emissions (no acid plant) relative to the nickel production and the poor economics, this plant was shut down.Nickel production from sulfide ores via pyrometallurgical means, especially the electric furnace smelting process, is a major emitter of SO2 to the environment and a big energy consumer (Warner, Diaz, Dalvi, Mackey, Tarasov and Jones, 2007). Nowadays, due to the more stringent environmental regulations as well as the need to reduce energy consumption, metal production by sulfation roasting is gaining more attention as an alternative process to smelting. The main focus of this paper is to investigate the extent and rate of leaching of valuable metals from the sulfation roasted nickel calcine, aiming to maximize the metal recovery and minimize the dissolution of iron species."

Jan 1, 2012

Late in 1974 at a meeting with the Cedar Coal Company in Chelyan, West Virginia, a very definite requirement for an automatic heat sensing fire suppression system for the type coal augers used in their mine was revealed. Several fires had been experienced, and while equipment loss was a consideration, operator safety was also a concern. As of that date no one had developed an automatic system specifically for fire suppression on coal augers. II. EQUIPMENT DEVELOPMENT As a result of the above meeting, an unsolicited proposal was made to the Bureau on March 1, 1975, and a contract was issued to provide the following services: A. Determine and define fire hazard problem on Compton Coal Auger. B. Modify or otherwise mike a Lease "AFEX" system suitable for protecting the fire hazard area developed in paragraph "A". C. Make installation of "AFEX" system. D. Monitor installation for reliability for a period of 90 days after installation. C. ConJurt a simulated fire test to determine effectiveness on system.

Jan 1, 1975

By Robert H. Hafner, Irvin R. Kramer, Stewart L. Toleman

IN his paper on the calculation of hardenability from chemical composition, Grossmann1 discussed the effect of most of the alloying elements used commercially. The purpose of the work reported in this paper was to determine the effect of several other elements on hardenability-arsenic, antimony, beryllium, cobalt, columbium, germanium, tellurium, tin, aluminum, and titanium-and to extend the range of composition of some of the elements studied by , Grossmann-chromium, copper, manganese, molybdenum, nickel and silicon. EXPERIMENTAL METHODS To determine the effect on hardenability, suitable amounts of the alloying elements were added to experimental heats and the hardenability determined by means of end-quenched hardenability specimens. The steels were melted in a high-frequency induction furnace with a basic crucible, using ingot iron as a base for some of the heats and S.A.E. 1015 for others. The alloying additions were made as ferroalloys or as metal, depending on the ' alloying element. Hundred-pound heats were split and poured into square, tapered, cast-iron ingot molds with hot tops. Aluminum was not used as a deoxidizer in most of the heats. The ingots were homogenized for 12 hr. at 1260°C. (2300°F.) , and forged into rounds of 1 ½ in. diameter. These bars were normalized twice from 840°C. (1550°F.) before machining into Jominy bars. The composition of the steels was deter- [ ] mined in most cases by samples taken from the end-quench hardenability specimen. As suggested by crafts,2acid-soluble

Jan 1, 1943

By A. V. Pavlov, V. A. Grygorian, Kossyrev, A. E. Semin, A. Korostylev

A new way of producing low-silicon ferrosilicon from iron-ore materials in a new type of aggregate-oxygen reactor is presented. The oxygen reactor process is based on using the calorific combustibility and reducibility of carbon materials inside the aggregate. The key to the process is successful post-combustion of carbon monoxide above a layer of a solid coke bed. Initially the possibility of production of grades of ferrosilicon containing 20 to 25% Si (FeSi20-FeSi25) was studied on a laboratory model of the oxygen reactor. Quartz sand and iron ore concentrates (from Russia and India) were used in the laboratory tests. This test work demonstrated that a ferrosilicon grade FeSi15 could be obtained directly from raw iron ore (containing 75.9 % Fe2O3 and a maximum of 23.8 % SiO2) without using rich iron-ore concentrates. The process was successfully tested on a pilot furnace at Serovsky metallurgical plant. Very promising results and efficiency parameters were achieved. The consumption of materials for 1t of ferrosilicon (15 % Si) production was as follows: 1567 kg raw iron ore, 591 kg of coal (in a composition of ore-coal briquettes), 299 kg of coke (for coke bed formation), and 815 m3 of oxygen.

Jan 1, 2004

By Jordan Mayorga, Joseph Kopp, Robert Boehm, Daniel P. Cook

"Solar generated power has long been considered a useful energy source only for low-energy density and non-mission critical use, such as providing electricity for residential applications. The success of Concentrating Solar Power (CSP) facilities, such as the 64 MW Nevada Solar- 1 near Las Vegas, have demonstrated that solar does have application to high energy density industries such as materials and chemical production. This paper will discuss the current operating con_guration of the Solar-1 facility and show how proposed modi_cations, such as addition of thermal storage and use of liquid salts as the working uid, can further improve the e_ciency and energy production of the plant.IntroductionThe United States as a nation is the largest consumer of energy in the world at an estimated 29 trillion kWh per year[1], which is roughly 15% of total global energy consumption[2]. On a per capita basis, the United States also leads most of the world, using an average of 96,000 kWh per person[3]. Roughly 40% of the energy consumed in the United States was produced from petroleum, 23% from coal, 23% from natural gas, 9% from nuclear and the remaining 5% from renewable sources such as solar, geothermal, wind, and hydroelectric[1].Energy demands associated with the industrial-scale production of chemicals and materials is a signicant portion of the United States total energy consumption. Roughly 33% of the energy consumed in the United States is used by the industrial sector, with 22% of this amount used in chemical production, 16% used in petroleum rening, and 14% used in the smelting and rening of metals[1]. Energy costs are also a signicant, if not the most signicant, portion of the total production costs for many materials. For example, roughly 30% of the cost of producing aluminum is the electricity used in the Hall-Heroult process [4], while the cost of energy is roughly 15% of the total cost of producing steel products [5].The primary sources of power for the industrial sector have been coal, petroleum, hydro- electric and nuclear. The use of alternative energy sources, e.g. solar, wind, geothermal, for industrial materials production has been slow in coming because they are intermittent and low-energy density sources, i.e. no solar power at night, no wind power when the air is still, etc. The success of Concentrating Solar Power (CSP) facilities, such as the 64 MW Nevada Solar-1 (NS-1) near Las Vegas, have demonstrated that solar can have application to high energy density industries such as materials and chemical production.This paper will discuss the current conguration of the NS-1 facility, and potential modications to the facility that will increase both its power e_ciency and power density."

Jan 1, 2010

By T. T. Chen, W. Petruk

The mineralogy of the feed, concentrates and tailings from the Heath Steele mill in New Brunswick was studied in detail to determine the liberation and recoveries of the major ore minerals, and to characterize the occurrence and distribution of the trace elements. The ore milled during August 1977 contained an average of 4.34 wt % Zn, 1.25 wt % Cu, 1.64 wt % Pb and 90 gr/ton Ag. The main trace elements in the ore are silver, cadmium, indium, cobalt, antimony, bismuth, arsenic, mercury, tin and gold. Silver is carried in solid solution in tetrahedrite-tennantlte, galena, Ag-Sb sulfosalts and Pb-Bi-Sb sulfosalts. Approximately half of the silver is recovered in the lead and copper concentrates and the remainder is lost in the tailings and Zn concentrate. As the major silver-bearing minerals also contain Sb and Bi, recovering silver by ore dressing would involve recovering elements that are troublesome in extraction metallurgy. Cadmium and most of the indium and mercury occur in solid solution in sphalerite and consequently are recovered in the zinc concentrate. Some indium is also recovered in the copper concentrate in a second unidentified indium-bearing mineral. Cobalt and arsenic occur principally in arsenopyrite, cobaltite, a Co-Fe sulfarsenide, pyrite and pyrrhotite, and follow these minerals into the tailings. Recovery of the valuable element cobalt, therefore, would involve recovering the environmentally hazardous element arsenic. Most of the tin and gold report to tailings. The ore was ground to about 80% minus 270 mesh. At this grind, 71 wt % of the sphalerite, 66 wt % of the chalcopyrite and 59 wt % of the galena were liberated. Recoveries of free sphalerite, free chalcopyrite and free galena in the Zn, Cu and Pb concentrates were 85 wt %, 76 wt % and 80 wt %, respectively; recoveries of unliberated sphalerite, unliberated chalcopyrite and unliberated galena in the respective Zn, Cu and Pb concentrates were 48 wt %, 5 wt % and 7 wt %. Some of the unliberated sphalerite and chalcopyrite grains in the tailings are large and would have been liberated at a finer grind.

Jan 1, 1980

By Hannon, J. W. G.

Silicosis is today's most important industrial disease and probably dates back to the Stone Age. Since the industrial revolution, increasing attention has been paid to those occupations where mineral dust is present in the air breathed by the workers. For many years it was assumed that the inhalation of all mineral dusts was hazardous. but investigations conducted in several countries pointed the statistical finger of guilt at free silica in any of its numerous physical forms as a dust of outstanding toxicity. Recognition of silica as the chief hazard has resulted in widespread use of the term "silicosis." Depending upon the concentration of finely divided silica dust to which the individual is exposed and the duration of exposure, silicosis may become a disabling condition in from one to thirty years. The structure of the lung and respiratory passages is such that only minute particles of silica can gain entry to the air cells in the lung (5 microns or under are most toxic). When these minute particles gain entry to the lung tissues they stimulate certain protective cells in the lung to multiply at an excessive rate. The cell's undergo inflammatory changes which result in nodular scars and a low-grade inflammation of the lung tissue. These progressive changes in the lung structure gradually encroach

Jan 1, 1949

By Edward H. Eisenbrey

This paper is primarily concerned with the exploration for massive sulphide orebodies. In a discussion of this type, it seems appropriate to establish a few definitions so that all parties may consider the same beast and its habitat. First, the term "massive sulphides", as used here, not only denotes a body of mineralized rock containing in excess of 50% sulphides by volume, but a mass of sulphides that respond as a conductor to the electromagnetic (EM) systems currently in use in exploration. "Disseminated sulphides" refer to all of those sulphide occurrences that respond to the Induced Polarization (IP) geophysical methods most commonly in use in porphyry copper exploration. This latter definition may also include the disseminated sulphide halos so frequently found associated with massive mineralization as well as banded and stringer sulphide mineralization. It is plain to see that these two end members of our definitions can easily blend into each other. The term "volcanogenic" refers here to any and all geologic processes that have their origin in volcanic activity. Thus we are concerned here with the exploration for massive sulphide ore deposits derived from and affected by contemporaneous and post mineral volcanic activity. Furthermore, most massive sulphide deposits are apparently formed in a submarine environment, deposited with extrusive rocks and sediments and/or chemical hot spring accumulations, then enclosed and protected by the addition of more volcanic and sedimentary material then, probably folded and deformed into one of their myriad of shapes.

Jan 1, 1973

By Robert S. Moehlman

Is recent years, exploration and development by diamond drilling has become a popular attack on the problem of finding new ore shoots and developing extensions of known shoots. Diamond drilling has been used in recent years in extensive sampling of disseminated copper deposits, in preference to churn drilling. At the Harvard gold mine, near Jamestown, California, Philip R. Bradley, Jr., general superintendent, reports that: "The Harvard work was a singular example of the reliance that can be placed on diamond drilling in evaluating an ore body." Drilling at the Harvard mine will be discussed in a subsequent section of the paper. So popular has diamond drilling become, indeed, that many who have had slight experience with drilling are inclined to regard it as a cheap cure-all. This paper proposes to show some of the limitations on the application of drilling and some of the steps that should be followed in drilling programs to obtain reliable results. Cost oF Drilling Drilling has the advantage, over shaft sinking and drifting, of lower cost and greater speed. As compared with churn drilling, the advantage of bringing up a coherent sample instead of fine cuttings for a sample is obvious. Diamond drilling is generally more expensive, however, and more engineering effort is required in combining the average of core and sludge samples. Exploration of drift walls by hammer drills to a depth of less than 30 ft. is generally cheaper than diamond drilling, but beyond this depth the diamond drill is cheaper and more efficient. The principal factor in determining cost of drilling is the character of the ground drilled. Broken ground with many fissures is most expensive to drill. Hard ground is less of a problem with diamond drills than with ordinary machine drills. Hardness or softness affects only the speed of drilling. Caving, easily washed, sandy or clayey ground requires continual cementing and casing, which is the greatest cost problem. Thus, soft, incompetent ground is more costly to drill than hard, massive ground. Cost of drilling per foot in good to fair ground varies from less than $I per foot, achieved in some districts in Ontario, the Mother Lode, and Missouri, to $5 per foot in many western states. In bad drilling ground, costs may range from $5 to $15 or more per foot, thus approaching the cost of drifting. Other factors that increase the cost per foot are: I. Short total length of hole drilled, so that the cost of moving in crews and equipment must be spread over a relatively few feet. 2. Cost of drilling per foot increases with depth beyond about 500 ft.. as more time is consumed in pulling rods' 3. Cost of preparing drilling stations, getting air underground to stations? etc' 4. Inaccessibility and lack of water on the job make for higher costs.

Jan 1, 1946

By Ping Yang, Tian-bin Li, Min-hui Wu

"The process of filtrate loss of low solid-phase drilling fluid at different content of polyanionic cellulose is investigated by the standard filtration test. The test results showed that when time of filtration is same, the filtrate volume decreases linearly with the increase of content of polyanionic cellulose. When content of polyanionic cellulose is same, the velocity of filter loss decreases nonlinearly with the increase of time and the velocity of filter loss will reach a stable value. The filtrate volume in 7 to 8 minutes can reach half of the total filtrate volume. At the same time, the velocity of filter loss of drilling fluid decreases nonlinearly with the increase of viscosity. When apparent viscosity is between 3.5~4.15 mPa.s, decrease speed of velocity of filter loss is quick. The results are helpful for characteristics evaluation of filtrate loss of drilling fluid and control of filtrate loss.IntroductionDuring the process of drilling, water of drilling fluid can leakage into stratum, the water can result in instability and collapse of borehole wall. At the same time, the original ratio of drilling fluid will change. The density of drilling fluid will increase, the performance of the drilling fluid will change. Controlling amount of filtration is important to drill successfully. The additives of controlling filtrate loss are mainly two types, particle materials and polymer materials. High-molecular polymer is a kind of high-molecular material, has the adsorption effect, high polymer protection, can improve the advantages of slurry viscosity (Xu,2004 and Dehghanpour,2001). Some scholars carried out some study on the polymer material fluid loss agent in recent years, these study mainly focused on CMC, HEC, MHEC, CMHEC, starch and its derivatives(Zhang,2005 and Chevron,2009).About PAC (polyanionic cellulose) as drilling mud additives, a few of scholars carried out some relevant work. Plank (1992) applied PAC into ordinary freshwater drilling fluid and analyzed temperature stability of freshwater drilling fluid. Bennion (2000) applied PAC into drilling fluid and analyzed effect of polyanionic cellulose on strata inhibitory. Huang (2011) analyzed effect of PAC on properties of the high-density water-based drilling fluid. Mahto (2004) applied PAC into fresh water and salt-water drilling fluid and analyzed effect of PAC on rheological properties of the drilling fluid. Wang (2008) applied PAC into alkaline drilling fluid to study various performance of drilling fluid. PAC is a renewable resource and has good application prospect (Ankara, 2005). So it is very important to understand the effect of PAC on filtration process of drilling fluid.The test was conducted by changing the content of the PAC in drilling fluid. The object of this paper is to understand effect of polyanionic cellulose on filtration process of the low solid-phase drilling fluid."

Jan 1, 2017

By Jason Ryan, Stephen Harria

Q.E.D. (QED) is a blast design and evaluation model that allows full three-dimensional design specification including the development of unique “live” terrains and an unlimited variety of complex charge configurations. QED’s analysis package allows the examination of likely outcomes resulting from changing various design variables in terms of vibration, fragmentation, rock-mass damage and muck-pile profile. Especially applicable to use cautious blasting applications, QED’s damage model uses vibration to estimate rock damage beyond excavation boundaries. This relates directly to operations such as Yucca Mountain Nuclear Waste Repository in Nevada, where damage beyond the excavation perimeter must be tightly controlled. The U.S. Department of Energy (DOE) h as b een studying a site at Yucca Mountain, NV to determine its suitability for long term storage of nuclear waste. The main mechanism of waste isolation will be the natural barrier of the host rock Total Systems Performance Assessment (ISPA) is used to model the excavation design and its behavior over time. Of importance to TSPA is quantifying the condition of the rock-mass before and after excavation. Ideally, there should be no excavation-induced changes to the rock-mass’ structure (removing the requirement to model the effects). At the least it may be possible to keep excavation-induced damage far enough away from waste packages so that modeling of these effects will not be required. QED can calculate a prediction of the extents of blast induced damage to the rock-mass. By using this metric as a design parameter, it may be possible to complete excavation of the repository more rapidly and inexpensively than previously thought, without jeopardizing the structural integrity of the waste containment areas or requiring blast damage to be modeled by the TSPA. This paper will explain the structure of the QED blast modeling system and show the analysis of historical data from Yucca Mountain. Processing of the historical data and the subsequent results will demonstrate how blast modeling can be used on an ongoing basis to assist the excavation process at Yucca Mountain.

Jan 1, 2000

By J. W. Langford

A more effective method of fracturing and chipping the formation is necessary to significantly increase the productivity of blasthole drilling with a roller cone bit. The conventional rotary blasthole bit engages the formation and initiates spalls, chipping and fractures in the formation at a rate dependent on the amount of pull down force applied by the drill. The rotary speed of the drill increases the number of fractures and creates drilled chips that are removed from the hole by the air circulation. An engineering project was motivated to develop a low pressure, low impact downhole percussion hammer to provide an overstrike force to a blasthole bit, in addition to the conventional pull down force and rotary speed. The objective of the project was to utilize existing rig air packages in the range of 50-110 psig and provide an overstrike force to the bit in the range of 1100-1500 impacts per minute. Laboratory testing performed on Barre granite achieved, on average, a 40% improvement in rate of penetration. This performance has been confirmed in actual blasthole drilling in copper and iron ores mines. During the testing phase, additional unexpected benefits have also been realized.

Jan 1, 2011

By C. S. Smith, Chih-Chung Wang

TURNBULL and his collaborators1,2 have developed the theory of homogeneous nucleation as applied, inter alia, to solidification of liquid metals. Vonnegut³ and Turnbull4 have shown that if a liquid metal is subdivided into small droplets a vast majority of them will undercool very considerably before solidification, generally to as low as about 0.8 of the freezing temperature on the absolute scale. The nuclei effective at small degrees of supercooling in bulk metal seem to be internal or surface heterogeneities, relatively small in number. If the metal is subdivided, those droplets that happen to contain such nuclei will solidify at a temperature not greatly below the true freezing point, but only a small part of the whole volume will be affected and the majority of the drops will under-cool to the much lower temperature at which homo- geneous nucleation occurs as a result of fluctuations. It occurred to one of the authors that an appropriate subdivision to give effective freedom from random nuclei is produced during the solidification of many alloys that contain a minor amount of a phase of low melting point, and that one might then expect marked undercooling of the distributed phase. Experimental: The alloys selected for initial study were copper with minor amounts of lead and bismuth, and aluminum with tin. In all these alloys, the major component freezes at a temperature not much below that of the pure metal, and there is little further change in constitution on cooling until the lower melting point constituent freezes in an almost pure state. Cooling curves were taken using the controlled heat flow method permitting approximate specific heats to be obtained. Chromel-alumel thermocouples were used, with the standard emf tables, since extreme precision was not needed. The crucible (3/4 in. id, 5/16 in. wall) was made of B & W K-20 insulating brick. It held about 10 cc of the alloy being investigated. The cooling rate was 2.5" to 2.9°C per min under a controlled temperature difference of 20°. Approximate specific heats were computed from the inverse rate curves together with data from a blank run and from a standard run with a copper cylinder of known heat capacity. The alloys for investigation were made from high-purity metals (99.99+pct) and cast into graphite molds. The castings were machined to fit the crucible and to provide a hole for the inner thermocouple. Cooling curves were taken after heating to a temperature about 50" above the melting point of the minor, lower melting-point, constituent. Results The lead phase in an alloy of copper with 5 pct lead did not undercool more than 3" below the melting point of lead (327°C) either as cast or after annealing to produce a new dispersion of the liquid phase. A copper-zinc-lead alloy with 23.75 pct zinc and 5 pct lead undercooled more but showed no thermal effect below 319°C. A cast alloy of copper with 5 pct bismuth undercooled to 249°C (M.P. bismuth 27l °C), but once solidification started it was completed at the same temperature. This was anticipated, since the bismuth forms a nearly continuous phase between the grains of copper, and a solid crystal nucleated anywhere would rapidly* con- sume the entire network of liquid, unless the physical continuity of the liquid were broken through volume changes, inadequate fluidity, or gas evolution. Similar arguments apply in the case of copper-lead alloys, where the lead-rich liquid forms a network along grain edges, though not grain faces. In both cases there would be a few isolated particles

Jan 1, 1951

By W. M. Pytel

The applicability of the beam theory in analysis of roof- pillar-weak floor interaction in partial extraction room-and-pillar mining is presented. The mine structure is modeled as an equivalent multi-indeterminate overburden elastic beam supported by elasto-plastic pillars; resting on a viscoelastic layer of immediate weak floor strata underlain by a competent rock mass. The developed analytical model was initially utilized to conduct sensitivity analyses of different variables affecting the mining system, such as the deformability of coal and weak floor strata, thickness of weak floor strata, number of pillars in a panel, width of pillars, width of panel etc. These analyses were then extended to three overburden strata - coal pillar - floor strata lithologies typical of active coal mining areas in Illinois.

Jan 1, 1989

By P. R. Khangaonkar

The industry of tin ore mining, beneficiation and smelting gives rise to a number of waste products like the beneficiation plant wastes (called amang), tin smelting slags, refinery dross etc. Some of the wastes deserve treatment to obtain economically useful products or to recover the metal values. The paper describes studies conducted on two materials, viz., struverite-middling (struverite-magnetic tin), which is an intermediate product of beneficiation circuits of tin tailings, and tin-smelting slags. The struverite middling was studied for treatment by chlorination using carbon tetrachloride, so as to yield vapour products separable by convenient condensation. The treatment was also found to lead to a tin-rich product amenable for treatment by known hydrometallurgical routes. The tin smelting slag was studied by alkali-leaching so as to avoid any dissolution of iron and it was possible to obtain an iron-free product solution suitable for high purity tin recovery.

Jan 1, 1996

By G. L. Oldright, Virgil Miller

"ACKN0WLEDGMENTSThe data given in this paper were collected at the Bunker Hill smelter through the courtesy of Stanley A. Easton, the vice-president and general manager, Frank M. Smith, the smelter director, and with the assistance and cooperation of A. F. Beasley, the smelter superintendent, and his staff members.THE BLAST FURNACE AND PLANTThe general lay-out of the recently built (1917) Bunker Hill plant has been given in the technical press in articles that were cited in Report of Investigations 3088. In addition it may be noted that the description of an ideal smelter given by Riddell 5 a year later fits the Bunker Hill smelter very well, with some changes, such as the location of the stack, made necessary by topography. For purposes of this article on the blast furnace it may suffice to state that the plant is one of the ""side hill location"" type. The various successively lower benches may roughly be considered as made for (1) the stack, (2) Cottrells and bag houses, (3) Dwight and Lloyd sintering machines with the equipment or bins for handling or mixing the feed and storing the finished product, sinter, and (4) the blast furnace feed floor with a slightly rising gradient to the bottom of the bins for sinter, feed, and take. The lowest bench (5) might be considered that of the blast furnace tapping floor at which or at appropriately slightly lower elevations are located the units for softening, refining, and treating precious metals, and for casting and loading lead. A very careful study of grades was made in order to be able to handle the products easily. All units were left with at least one end open to permit expansion of the plant, it desired, and each unit was separated from the other, evidently so that the operators on one level would be annoyed as little as posssible with the products made on another."

Apr 1, 1931

By James K. Gowans

Polaris Mine, a Cominco Ltd. property located on Little Cornwallis Island, Northwest Territories, Canada, (Lat. 75°30'), is the world's most northerly base metal mine. Polaris Mine, which commenced operations in late 1981, is characterized by its unique process barge. The lead/zinc concentrator, powerhouse, shops, offices, dry and warehouse have all been incorporated on a 400 ft. long by 100 ft wide by 65 ft high barge. This process barge was constructed in Southern Canada, at Trois Rivieres, Quebec, then towed 3500 miles into its final resting place on the high arctic. This paper describes the unique design of the barge concentrator and deals with the start-up and continuing operation of the Polaris Concentrator.

Jan 1, 1984

By C Hamilton

Stawell Gold Mines (SGM) is an underground mining operation located in Victoria, Australia. The mining method employed is long hole retreat stoping, utilising up and downholes and artificial concrete pillars. Stawell is currently mining the Golden Gift and Magdala orebodies.Access to the Magdala and Golden Gift deposits is via 6.0 m wide by 5.5 m high declines developed at a gradient of one in eight to one in seven from the surface to a depth of 1500 m, with a planned depth of 1650 m. From the declines, cross cutting drives are developed to intersect the orebodies. Orebodies in the Gift system are discrete lodes which are generally mined from a bottom up centre retreat to minimise geotechnical stresses.Ore development fronts are currently located between 1000 m and 1500 m below surface, with all ore being hauled to the surface using a fleet of 60 tonne underground trucks. With the use of conventional pyrotechnic long period (LP) delays, broken rock of combined ore and waste is thrown 10 m from the face and the materials hauled to the surface. The majority of the mullock from development is consumed in the underground as backfill.With the use of Orica Mining Services eDev™ Electronic Blasting System for Tunnelling, the waste is thrown up to 40 m from the face, while majority of the ore is left 5 - 10 m from the face, effectively segregating ore and waste. This enables significant recovery of gold values with minimal loss and significantly reduced dilution. By using this technique in ore drives with a 30:70 waste to ore ratio, SGM is able to haul 24 000 tonnes less mullock to the surface annually. Resue mining is applied to narrow vein headings and gives a 40 per cent grade increase at the faces as well as increasing the economic footprint of development. This will also contribute to an improved grade profile for the year from 3.98 - 4.16 g/t Au and allow extra capacity for ore haulage from stoping and for milling.This paper describes the application and the successful blast outcomes achieved using the eDev™ Electronic Blasting Systems for resue mining at SGM. Results to date, since commencement in March 2010, have been achieving significant benefits in terms of ore grade as confirmed by geologists grab sample grades. Face advance have also shown improvement with better breakage of perimeter holes giving improved face profile. These benefits are delivering increased productivity and safety performance when compared to other resue firing techniques.

Mar 21, 2011

By L. Patts, J. Rohrbaugh

The Mine Safety and Health Administration (MSHA) has received several reports of filters igniting when high-temperature disposable filters were used on non-cooled diesel exhaust systems in underground coal mines. Based on laboratory testing (to determine the ignition temperature of these filters, which were loaded in the field with diesel particulate matter, or DPM), MSHA determined a maximum safe operating temperature for high-temperature disposable filters. When the results of the laboratory filter ignition testing were reported to the Coal Diesel Partnership (comprised of members of the Coal Industry, Labor, NIOSH and MSHA) the Partnership charged NIOSH with investigating the safe use of high-temperature disposable filters. This paper reports on the design, fabrication and testing of a unique exhaust gas cooling device and the ability of this device to successfully lower filter inlet temperatures and thus reduce the potential for fires.

Jan 1, 2009