Search Documents

By A. A. Smith, J. S. Smart

THe elements silver, cadmium, tin, antimony and tellurium either are found as impurities in commercial coppers or are intentionally added to produce coppers for special uses. When present in small quantities, each of these metals exerts a significant effect on the properties of copper, but despite considerable experience and investigation much remains to be learned about their specific behavior. The presence of extraneous elements, particularly oxygen, complicates the study of individual additions of impurities in the range o to 0.05 per cent, and the use of high-purity copper has been found extremely helpful in circumventing these difficulties. It has also been found that individual behavior can be satisfactorilv determined from measurements of two commercially important properties, conductivity and softening temperature, according to methods that have been described previously.1,2 Data of this type, obtained in the course of a general investigation of the effects of impurities on the properties of both oxygen-bearing 2nd oxygen-free copper are presented herewith. All samples except those containing cadmium were prepared as 3/8-in. continuously cast oxygen-free rod from pure copper and weighed amounts of a similarly synthesized master alloy. Composition was checked by chemical methods, which in every case verified the calculated analyses. Test wires were cold-drawn one B, and S. number per pass on a string-up machine using four 30-min. 600°C. anneals at 0.3125, 0.257, 0.204 and 0.162 in. and a final cold reduction of 75 per cent to 0.081 in. Some oxygen-bearing samples were produced directly from the 3/8-in. oxygen-free rods by diffusion from a surface scale at 850°C. and drawn to size as listed above, but most of the alloys were remelted in pure graphite and cast through air into a I-in. round mold. The slugs were then hot-rolled to 5/16 in., drawn to 0.162 in., annealed as listed above, and drawn to 0.081 inch. Conductivity wires were annealed for I hr. at 100°C. intervals between 300' and 800°F., using a hydrogen atmosphere for oxygen-free samples and purified nitrogen for the oxygen-bearing type. All samples were quenched from the annealing temperature in 10 per cent H²S04 and conductivity was measured on a Hoopes bridge that had been checked against a Kelvin bridge. The softening temperatures represent the half-hard stage of the annealing curve as determined by a standard procedure.' Effect of Silver Numerous excellent studies of the argentiferous coppers are found in the literature, and these have been adequately

Jan 1, 1943

By A. A. Smith, J. S. Smart

THe elements silver, cadmium, tin, antimony and tellurium either are found as impurities in commercial coppers or are intentionally added to produce coppers for special uses. When present in small quantities, each of these metals exerts a significant effect on the properties of copper, but despite considerable experience and investigation much remains to be learned about their specific behavior. The presence of extraneous elements, particularly oxygen, complicates the study of individual additions of impurities in the range o to 0.05 per cent, and the use of high-purity copper has been found extremely helpful in circumventing these difficulties. It has also been found that individual behavior can be satisfactorilv determined from measurements of two commercially important properties, conductivity and softening temperature, according to methods that have been described previously.1,2 Data of this type, obtained in the course of a general investigation of the effects of impurities on the properties of both oxygen-bearing 2nd oxygen-free copper are presented herewith. All samples except those containing cadmium were prepared as 3/8-in. continuously cast oxygen-free rod from pure copper and weighed amounts of a similarly synthesized master alloy. Composition was checked by chemical methods, which in every case verified the calculated analyses. Test wires were cold-drawn one B, and S. number per pass on a string-up machine using four 30-min. 600°C. anneals at 0.3125, 0.257, 0.204 and 0.162 in. and a final cold reduction of 75 per cent to 0.081 in. Some oxygen-bearing samples were produced directly from the 3/8-in. oxygen-free rods by diffusion from a surface scale at 850°C. and drawn to size as listed above, but most of the alloys were remelted in pure graphite and cast through air into a I-in. round mold. The slugs were then hot-rolled to 5/16 in., drawn to 0.162 in., annealed as listed above, and drawn to 0.081 inch. Conductivity wires were annealed for I hr. at 100°C. intervals between 300' and 800°F., using a hydrogen atmosphere for oxygen-free samples and purified nitrogen for the oxygen-bearing type. All samples were quenched from the annealing temperature in 10 per cent H²S04 and conductivity was measured on a Hoopes bridge that had been checked against a Kelvin bridge. The softening temperatures represent the half-hard stage of the annealing curve as determined by a standard procedure.' Effect of Silver Numerous excellent studies of the argentiferous coppers are found in the literature, and these have been adequately

Jan 1, 1943

By Reamy Joyce

CONDITIONS in underground mining are so variable that in approach-ing the problem of the economies effected by the use of pressure-treated mine ties and mine timbers, it is necessary to secure specific data for each mine. Facts must first be dug out to show the service life of untreated timber and the reason for its failure. Generally speaking, decay is the usual cause of failure, but in some mines mechanical destruction is an important factor. Occasionally the two causes combine to produce fail-ures, and it is difficult to determine positively which factor is responsible. In making comparisons, it is always necessary to start with the cost in place and for this reason there must be accurate information covering the labor cost of installation and the labor cost of renewals. When treated timber is used, it is necessary to know the specifications for the treating process, whether the timber was painted, dipped, treated open tank, or impregnated under pressure according to standard specifica-tions. It is also necessary to know the preservative used and the amount of the preservative that was retained by the timber after treatment. It is also well to know whether the timber was thoroughly air-seasoned before treatment or was green at the time it was treated. The kind of timber available, both untreated and treated, must be known and all of the factors listed above must be taken into consideration in the study of any problem.

Jan 1, 1939

By Francis J. Kiessling

Energy and the conversion of potential energy into alternate forms is becoming a topic of household conversation for a larger segment of the world's population as mankind's desire for products derived from the vast array of technological developments continues to expand. The world's use of steel and the high energy consumption related to the production of steel promotes an awareness of the limitations of existing technology and a search for more economical alternates. Terminology such as (BF) Blast Furnace, (BOP) Basic Oxygen Furnace, (EAF) Electric ARC Furnace, (DR) Direct Reduction, (DRI) Direct Reduced Iron and (FC) form coke is becoming commonplace as alternates are being sought to alleviate the energy crunch. Coke production by various methods was developed as early as the seventeenth century in Europe to replace the disappearing hardwood forests that supplied the initial blast furnace fuel in the form of charcoal. In 1880, the Semet Solvay by-product coke oven design was introduced to the United States at Syracuse, New York, to supply coke for use in the production of soda ash, coke oven gas and its by products as the primary source of many organic processes. Although the Semet Solvay coke oven has not been marketed for decades, these coke oven batteries are in use today producing metallurgical coke, coke oven gas, and related by-products.

Jan 1, 1980

By M Kozikowski

The primary purpose of these investigations is to determine dewatering requirements and likely impacts associated with mining operations. Standard aquifer testing techniques were carried out at multiple locations within the Ord Range near Pardoo, Western Australia. Aquifer properties of an oxidised haematite orebody were calculated from test pumping data conducted in five fully penetrating test bores. Hydraulic properties of the Ridley magnetite orebody were calculated based on short term constant rate pumping tests, and packer tests. Packer tests were conducted in undeveloped and uncased exploration holes and diamond core holes. The new data sheds light on the hydrogeological properties of this previously unexplored region of Western Australia.Aquifer testing procedures for each bore included a preliminary step test followed by a constant rate test. Recovery data were collected in each bore over a period of four to six hours. Prior to testing, background water levels and water samples were collected in a network of monitoring and exploration bores to establish baseline water levels, gradients and water quality. Water quality within the bedrock of the Ord Range varies from 2000 to 5500 mg/L TDS whereas water quality within the alluvial sequence of the De Grey River is highly variable (400 to 2500 mg/L TDS), but is predominantly brackish with some water of potable quality which is used to supply Port Hedland. Test pumping supports the conceptual hydrogeological model that consists of a pod like orebody (aquifer) surrounded by low permeability waste rock (BIF), with very weak hydraulic connection to the adjacent alluvial systems. Calculated hydraulic conductivity from test pumping data across Pardoo ranged from 0.01 to 59 m/d, depending on deposit tested.A groundwater model was used to simulate dewatering required in proposed pits and to estimate the impact of dewatering on the surrounding shallow alluvial aquifers. Test pumping and numerical groundwater flow modelling indicate the proposed below water table pits can be successfully dewatered utilising in pit dewatering production bores. Yields from individual dewatering bores will reduce with time due to the reduction in saturated aquifer thickness.Based on the numerical groundwater modelling and field investigations the likely impacts to the adjacent De Grey River alluvial aquifer system (within the Priority 1 De Grey River Water Reserve) resulting from mining and dewatering activities is considered minimal. Recalibration of the groundwater model will be undertaken once several months of dewatering data are available.The aim of this paper is to present a range of aquifer parameters derived through standard aquifer testing techniques for an area previously unexplored in terms of hydrogeological characteristics. It is the goal of the authors to provide this comparison data set for future work in similar geologic media.

Jan 1, 2009

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members) Members and guests who called at Institute headquarters during the period Jan. 10, 1917 to Feb. 10, 1917: Victor C. Alderson, Denver, Colo. G. Komar, New York, N. Y. Arthur W. Allen, New York, N. Y . H. H. Lauer, Allentown, Pa. George S. Blair, Pittsburgh, Pa. Frederick MacCoy, Antofagasta, Chile. F. J. Brulé, Toronto, Canada. E. P. Mathewson, Toronto, Canada. W. M. Corse, Buffalo, N. Y. Douglas Muir, San Antonio, Tex. John J Croston, Cullasaja, N.' C. F. W. Osborn, Ajo, Ariz. W. A. Deane, Waxhaw, N. C. Mortimer A. Sears, Washington, D. C. P. H. Dudley, New York N. Y. W. H. Selden, Jr., Iron River, Mich. J. D. Gilchrist, Denver, Colo. W. H. Staver, Yonkers, N. Y. L. Hoffman, Pottersville, N. J. Ralph H. Sweetser, Easton, Pa. Guy R. Johnson, Florence, Wis. Benjamin F. Tibby, Salt Lake City, Utah. W. McA. Johnson, Hartford, Conn. Carl J. Trauerman, Butte, Mont. John S. Kennedy, Philadelphia, Pa. H. C. Wilmot, Arequipa, Peru. D. C. Bard has become a member of the geological department of the Chicago, Milwaukee & St. Paul R. R., with headquarters at Seattle. Jay A. Carpenter has resigned his position as metallurgist for the West End Consolidated at Tonopah and has been appointed superintendent of flip. Nevada. Packard mines it Rochester.

Jan 3, 1917

By G Noonan, S Thomas, M Limbert

Stuck drill rods (often referred to as bogged rods) in production ‘upholes’ are a common problem in the underground mining industry. Bogged and broken off drill rods have the potential to fall out of the hole without warning, posing a serious hazard to personnel and equipment below.Current industry practice to alleviate this hazard can be to either grout the hole in order to lock the drill rods in place, or to ‘plate over’ the hole with a rock bolt. Each of these operations seriously delays mine production as both require demobilisation of the production drill and mobilisation of alternative personnel and equipment to address the hazard. Both methods have been assessed for safety and efficiency and were found to be expensive, time consuming and in the case of plating over, ineffective.To address the safety and efficiency short-comings of the traditional practices, the long hole plug (LHP) has been developed to safely secure the lost rods in the hole. The LHP when struck by falling drill rods behaves similar to an expansion shell anchor transferring the axial forces from the falling drill rods horizontally into the rock mass. It is installed using standard production drills allowing work to safely continue with little interruption.Extensive testing has been carried out on the LHP in the laboratory and underground at the Rosebery mine on the west coast of Tasmania, Australia. Testing has included static pull testing, full scale drop testing and underground trials.The outcome of this work has proven the LHPs ability to add safety, volume and cost benefits to the Rosebery underground operation and it is currently in use at that site. It enables proven elimination of a common workplace hazard immediately, thus eliminating delay on the mine’s production cycle.CITATION:Thomas, S, Noonan, G and Limbert, M, 2017. Long hole plug – addressing the hazard of bogged rods in ‘upholes’, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 305–310 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By F Butler, G E. Batley, A C. Hogan, A R. Butler

The ANZECC/ARMCANZ (2000) Water Quality Guidelines (the Guidelines) are the primary reference used in Australia and New Zealand for managing and regulating water quality. For most mining operations in Queensland, the environmental authority (EA – licence) incorporates the national default guideline values (GVs) for ecosystem protection as trigger levels (TLs). Exceedances of TLs ‘trigger’ further investigation and reporting. A review of the surface water compliance history at a metalliferous mine in North West Queensland identified minor exceedances of the cobalt GV as a common trigger for investigation and compliance reporting.The reliability of GVs is dependent on the availability and quality of ecotoxicology data for the relevant contaminant. The current national default GV for cobalt of 1.4 µg/L is classified as a low reliability GV due to the lack of available data at the time it was derived (ANZECC/ARMCANZ, 2000).The Guidelines are presently being revised and the toxicant GVs will be available as a set of web-based values and associated technical briefs. The new platform will enable the timely revision of existing GVs and inclusion of GVs for additional toxicants. Cobalt was considered a priority toxicant for the Guidelines’ revision, but was not included in the revision process.A preliminary review of the international literature indicated that at least 15 additional chronic cobalt toxicity studies had been published since 2000, sufficient to derive a high reliability cobalt GV using the protocols developed for the revision of the Guidelines (Batley et al, 2014; Warne et al, 2015). This presented an opportunity to improve environmental management by increasing the reliability of the performance measure.CITATION:Hogan, A C, Butler, A R, Butler, F and Batley, G E, 2016. Derivation of high reliability water quality guideline values for cobalt in freshwaters – improving water quality guidelines for better water quality compliance management in mining, in Proceedings Life-of-Mine 2016 Conference , pp 205–208 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By Jeffrey Oke D.S.H. Oke, Craig J. Archibald, Anna P. Perry

Underground mining at the Diavik Diamond Mine (Northwest Territories, Canada) commenced in 2003 and has targeted four kimberlite pipe orebodies. The A154 North (A154N) pipe was mined using longhole open stoping with cemented and uncemented rock fill. During the later stages of mining, unique geotechnical challenges developed in the upper portion of the orebody, resulting in difficult ground conditions during secondary stoping. The two uppermost stoping horizons in A154N (A- and B-blocks) were located within the widest portion of the kimberlite pipe and were mined using a multi-panel retreat, overhand primary–secondary extraction sequence. Primary stopes were commonly advanced to near the top of each block prior to the initiation of secondary stoping. Ore development was excavated to full stope width, and secondary development initiated at the base of the block adjacent to mined-out primary stopes resulted in the formation of tall, slender hanging pendant pillars—locally up to 100 m high—laterally supported by frictional contact with adjacent cemented rockfill pillars. Beginning in 2015, differential vertical movements across the ore-waste contact of A154N pendant stope pillars were identified, and the extent and rates of movements increased significantly as secondary stoping progressed through to 2025. These conditions created significant challenges for the safe extraction of remaining stopes and raised concerns for deeper mining blocks if similar methods were maintained. This case study describes the factors contributing to the observed ground behaviour and outlines the strategic mine design modifications and tactical risk mitigation measures implemented to manage geotechnical risk in the remaining A- and B-blocks and to prevent recurrence in lower A154N mining horizons.

May 2, 2026

By Malcolm D. Flavel

Recent research into the mechanisms of crushing processes has led to the establishment of new criteria for the effective design and operation of comminution plants. This paper reviews this work and gives examples of the productivity gains and cost benefits that have been achieved in the practical application of these findings.

Jan 1, 1988

By D FitzGerald

A critical component of any new tunnel design in a complex geological setting is the development of an integrated three-dimensional (3D) geology model with a full set of geotechnical properties of the rocks present. A novel means of predicting the geology based upon sparse observations of structural geology at the surface and from drill holes has been developed and used in several major tunnel studies in Europe.An example of this is the Lyons-Turin twin rail tunnel which is still in a development phase. This tunnel has been in planning and development for over 15 years already. An important aspect of this work is to characterise geological uncertainty along various possible tunnel paths as an input into early design optimisations for time, cost and risk avoidance strategies. Once the tunnel works commence and more detailed geological data is collected by daily mapping, progressive refi nement of the geological model is desirable; geological conditions still to be encountered can be more accurately predicted. Faults and their offsets, dykes, geological unconformities, folding, as well as standard sedimentary processes are all correctly modelled in the software. It is important to allow for seamless interchange of geological models at various scales with CAD workflows so that sufficient detail can be readily accessed at the required scale. Also, the proposed tunnel in its correct geometry can become a ‘section’ in its own right. Progressive detailed local geology models in the vicinity of the advancing head are created from the regional scale work by cutting and pasting a starting model, then adding all the extra detail for the required engineering geology work.For all rocks, most standard geotechnical quantities such as sonic velocities, Young’s modulus and Poisson’s ratio are handled. These and any other phenomena from borehole observations can have variograms calculated and stratigraphically constrained estimations made in a least biased geostatistical manner, in advance of the tunnel. RQD, or a prediction of rock fractures, is handled by the faulting and folding modelling facilities. This is probably the more interesting issue to pursue, as the fractal nature from small scale fractures and joints, to large-scale faults, can now be characterised more convincingly.

Mar 8, 2011

By M J. Nugus, F Clark, E J. Hill, J T. Carswell, J S. Cleverley, N H. S Oliver

High-nugget gold orebodies are difficult to model in 3D because samples from diamond drill core are generally too small to provide reliable estimates of the gold content of the larger body of rock, and therefore interpolation of gold assay values between drill holes is also unreliable. As a result, gold resources are generally underestimated in areas of high nugget. In practice, proxies for gold mineralisation, such as presence of alteration, specific structures or high vein density, have been used by geologists to predict rocks which are favourable for mineralisation. However, there has been no automated method for combining the predictive capabilities of several proxies, except by human judgement.We have been developing a method to combine several different types of geological features or geochemical analyses into a single measure using conditional probability. Conditional probability provides a meaningful numerical measure for the favourability of rocks for containing high-grade gold mineralisation. This measure can be interpolated in the exploration space, providing a sound basis for a 3D model of the orebody. We have developed this technique using data from the Sunrise Dam Gold Mine, which is a high-nugget orebody hosted in a structurally complex Archaean greenstone belt and which has historically proved to be a very challenging orebody to model.CITATION:Hill, E J, Nugus, M J, Clark, F, Oliver, N H S, Cleverley, J S and Carswell, J T, 2013. Predictive three-dimensional modelling of nuggety gold orebodies, Sunrise Dam, Western Australia, in Proceedings World Gold 2013 , pp 463-468 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By Francis M. Walters

THE problem of making iron-manganese alloys of scientific purity is a rather difficult one. They cannot be prepared in air because of the readiness with which the metals oxidize at the temperature of melting; and they cannot be prepared in vacuum because of the, high vapor pressure-of- manganese. The very property of: manganese which permits it to be purified interferes with the utilization of the best method of making pure alloys. Accordingly, it is necessary to use a gas atmosphere which will not affect the-properties of the alloys. The gases available for the purposes are hydrogen; helium and argon. Nitrogen forms intermetallic compounds with manganese very readily. Hydrogen, while valuable as a deoxidizer and having the advantage of being comparatively cheap, is explosive over a wide range and, has a rather high thermal conductivity. Helium is reported as, costing little but is difficult to secure at a reasonable price and also has a conductivity nearly as high as hydrogen. Since argon has a sufficiently low thermal conductivity, it has been selected for use in one induction furnace for melting, under a controlled, gas atmosphere, in spite of its cost, which is so high (70 cents to $1.50 per cubic foot) that it must be stored and purified.. Such a gas atmosphere-as argon makes necessary the use of the, high-frequency induction method of heating. This involves, a non-metallic container for the gas; .which is most conveniently of fused quartz or glass. The next

Jan 1, 1929

By Manca PP, Lassandro R, Caranassios A, Massacci G, Ciccu R

The paper discusses the state of the progress reached in the development of the diamond wire tool for cutting hard rocks. To the advances of this relatively new technology a substantial contribution has been provided by the research being carried out at the University of Cagliari on samples of granite rocks from different Sardinian stone quarries. On the basis of field experiments and laboratory test data, the mechanism of diamond wire cutting has been assessed. In particular the influence of the rock features and operational variables on tool performance (cutting rate and bead wear) has been Elucidated.

Jan 1, 1992

A homely simile will serve to epitomise an interpretation of the rock structures and associated phenomena of the block of country under review, as it appears to the writer.Disregarding the many thousands of feet of overburden that have been eroded away during the ages, the present denuded surface and rock systems below may be pictured as a slab of some titanie ribbon cake that has suffered much damage from rough handling and exposure, yet retaining much of the original symmetry of its superimposed layers of variegated colour and texture.Lateral pressure has crumpled the cake into a series of irregular corrugations and, in parts, has caused some of the layers to crush and slide over their neighbours.Following upon this squeeze, the cake has been severed into segments and rhomboidal slabs by vertical cuts, and these portions have been severely jostled one against its neighbour, crushing the faces of contact and dragging the contiguous layers in the direction of movement.The variegated icing of the cake is represented by intercalated sills of amphibolite, pegmatite, and aplite, and the body of the cake by highly altered sedimentary rocks.The icing has been assailed by the rats of erosion with such effect that only residuals of the original structures remain. The body of the cake has suffered successive waves of igneous invasion in the order of lode pegmatite, followed by zine, iron,copper, and finally by silver-lead. These successive invaders found difficult access, along certain of the vertical cuts, to the more succulent layers of the cake, where, gorging to repletion, many were imprisoned and entombed for the future service of mankind.

Jan 1, 1927

By N. Behnood, W. Pascheto

"Laboratory wear tests are important tools that can be used for the evaluation of materials for wear applications and mitigation of wear problems in the mining industry. However, laboratory test parameters must be fully characterized and test results must be carefully interpreted if a material selection is to be made. Failure to do so may lead to erroneous conclusions. Suitable lab-oratory tests are valid only if they reflect the field conditions to which materials are subjected. Therefore, it is important to know, in detail, the field conditions, as well as the wear test techniques being considered. It is important to recognize the limitations of the various wear tests and the wear test data published in the literature. This work will review present wear testing technology, including the various wear tests avail-able, wear test equipment and test limitations. Several wear test procedures will be related to common equipment used in the mining industry.IntroductionThis paper will concentrate on non-lubricated wear mechanisms, because they are the most costly to the mining industry. Very frequently we are faced with the task of selecting materials for wear applications or improving existing systems that are giving poor performance. There are plenty of examples in the literature of practical wear cases and ranking of materials for wear applications. It is also very common to find materials manufacturers’ data -sheets listing wear tests results by comparing their materials performances against those of competitors. Much of the published wear data lack the description of the type of wear test, test parameters and the type of wear mechanism to which the data should be applied (if any).Before considering wear test data for a specific problem one should ask which type of wear mechanism is involved? What type of test and what test parameters were used to produce the results? Even if the type of wear tests and parameters are known, how accurate and useful are the published wear data? How are the results related to a particular type of wear? It is important to point out that even the standardized wear tests, such as those in ASTM standards, have limitations. Such limitations are recognized and clearly spelled out in the standards themselves. Basically, wear tests may lead to erroneous results if the test is not able to repro-duce the same wear mechanisms encountered in the field. Therefore, the use of published results may be helpful, as a starting point, but may be of little value for a final material selection.This work will discuss the main types of non-lubricated wear mechanisms encountered in the mining industry. In addition, it will discuss the many wear tests available and their correlation with the various types of wear mechanisms. The limitations of several standardized wear tests and the limitation of using published wear data will also be discussed."

Jan 1, 1997

By D. C. Fleck

Electrorefining yttrium from selected low-melting yttrium--base alloys is investigated, and various halide systems are studied as potential electrolytes for use in preparing low-oxygen yttrium by electrorefining unalloyed yttrium. Yttrium cathode products having significantly less metallic impurities than the anode materials were prepared from alloys containing nickel, iron, and manganese by electrorefining in LiCl-YC13 electrolytes at 900° to 1,000° C. Yttrium-copper and yttrium-magnesium alloys are not suitable as anode feed materials, An evaluation of chloride, fluoride, bromide, and mixed chloride-fluoride electrolytes showed that cathode products containing much less oxygen than the anode material can be obtained in the fluoride and mixed chloride-fluoride systems. Initial cathode current density has no apparent effect on the purity of the products obtained in both phases of the investigation.

Jan 1, 1973

By Stanley A. Schwartz

In the Piedmont, heavily loaded structures are generally supported by either drilled piers or one of several pile types. The choice of drilled piers or piles is typically one of comparative costs. The cost of a drilled pier foundation is usually the more difficult to predict because of the greater impact that variable conditions and construction monitoring have on cost. Poor specifications, related to the drilling equipment, procedures and bearing level, can also result in large cost extras. In the southern Piedmont, straight shafts are typically extended down to hard rock to achieve primary support in end-bearing: when bells are required, they are often constructed manually. In some eastern and northern Piedmont locations the thickness of the decompossed rock zone is significant and considerable skin friction can be mobilized. Typically piers are constructed in holes temporarily cased with steel liners. The bottom is cleaned of loose material and water, and then evaluated by a geotechnical engineer to confirm the design bearing pressure (and friction, where appropriate) or recommend alternative construction measures.

Jan 1, 1988

By Alejandro Freyre

Anteriormente metales como el berilio, zircofonio, hafnio, litio, se consideraron como metales raros. Sin embargo, son abundantes en las formaciones geológicas profundas. En ese sentido, el presente texto señala la nueva clasificación desde el punto de vista de la industria nuclear. De acuerdo a ello, se divide en dos grupos: en el primero, están los minerales o elementos desintegrables como el Uranio, Thorio, etc.; mientras que en el segundo, están los minerales o metales estructurales, el Zirconio, Hafnio, Berilio, Litio, etc. Son denominados estructurales porque intervienen, ya sea como auxiliares directos en el proceso de la desintegración emitiendo o subdividiendo iones.

May 1, 1955

By M. Z. Rashad

The purpose of this paper was to compare the covariance and multiquadric functions in same mining and geological applications. The basic principals of the two techniques are covered briefly. Similarities and dissimilarities of the covariance and multiquadric functions are discussed geometrically, mathematically and practically. A 14 by 16 kilometer square area in Baharia Oasis, Western Desert of Egypt, was selected for a detailed comparative test. The gravity anomalies of forty-eight test stations were computed by using the data of sixty-three control stations. The results indicated that the covariance function is quite better than the multiquadric one. On the other hand, the multiquadric function more simple in computation than the other one, which needs to precalculations such as semivariogram and covariogram. Moreover, multiquadric equations are based on geometrical and physical considerations rather than covariance functions.

Jan 1, 1990