Search Documents

By Tom A. Armour

Different variations of soil nailing techniques have been used in the United States since the late 1970's. Such techniques owe their origins to French developments, which began in the early 1970's as a spin-off from European tunneling excavation support practice. The growing demands of urban infrastructure development and rehabilitation and environmental protection have created an active and expanding soil nailing market demand for earth retention and slope stabilization in the United States since its early developmental years. There is a clear need for a fundamental review of the large number of soil nailing techniques that are currently being used in the United States. Following a brief summary tracing the historical development of soil nailing and a generic classification of applications, this paper provides a review of the different recent advances in the design and construction of soil nailed systems. Discussion topics include nail design advances, permanent "top-down", structure support/underpinning, alternative face stability measures, composite systems, hollow bar and fiberglass nails and architectural reinforced concrete/shotcrete facings. Case histories will be presented to illustrate each of these advances.

Jan 1, 2003

[ ]

Jan 1, 1938

The compilation of the sampling nomogram is an essential tool in the optimization of a sampling protocol and allows the operator to track the change in relative variance of the sampling error (the Fundamental sampling error) during steps of comminution and mass reduction in the process of recovery of the aliquot for analysis. The data required for the compilation of the nomogram are centred on the sampling constant K and the exponent, alpha (a) of the nominal fragment size. Five methods for establishing K have been identified, but two of them, the duplicate sampling analysis method and the heterogeneity test method purport to provide such constant. The step by step procedure for each of these two methods was examined using broken ores from three mines, Mponeng mine, Kloof mine, and Lily mine. Two of these mines (Mponeng and Kloof) are typical Witwatersrand-type gold mines, and the third is an Archaean-type shear related gold deposit situated in the Barberton Greenstone belt. The results suggest that the factor K derived using the heterogeneity test is very accurate, but applies only to a single size fraction in the spectrum of comminuted materials. The calculation of gold grain sizes using this method appear to be too small and do not conform with the results from detailed mineralogical studies. The factors K and alpha derived using the duplicate series analysis are appropriate for use across a wide spectrum of comminution sizes and also provide realistic gold grain sizes, comparable with the equivalent circular diameter of gold grains identified in mineralogical studies of the ores.

Jan 1, 2010

By S. Castro, L. Gutiérrez, L. Uribe

"Use of lime in seawater as a pyrite depressant decreases Mo recovery in flotation of Cu- Mo sulfide ores. When technology that uses sodium metabisulfite (MBS) to depress pyrite is applied, the process is carried out at pH 6.5–7.5, the range where Mo recovery is higher than the usual pH 11.0–12.0 when lime is applied. Redox conditions and chemical reactions involved in depression mechanisms of pyrite by MBS, or sodium sulfite, in seawater are investigated and discussed based on the acidifying effect of MBS, oxidation of sulfite ions by dissolved oxygen, and the role of catalyst of some metal cations (e.g., copper ions) adsorbed on pyrite’s surface.RÉSUMÉ L’utilisation de chaux dans de l’eau de mer comme agent déprimant de la pyrite réduit la récupération de molybdène (Mo) dans la flottation de minerais sulfurés de Cu-Mo. Lorsque l’on applique la technologie utilisant du métabisulfite (MBS) de sodium comme agent déprimant de la pyrite, le procédé se fait à un pH de 6,5 à 7,5, gamme dans laquelle la récupération de Mo est supérieure au procédé habituel utilisant un pH de 11,0 à 12,0 lorsque l’on applique de la chaux. Les conditions de réduction-oxydation (redox) et les réactions chimiques impliquées dans les mécanismes de dépression de la pyrite par le MBS (ou sulfite de sodium) dans de l’eau de mer sont étudiées et débattues sur la base de l’effet acidifiant du MBS, de l’oxydation des ions sulfites par de l’oxygène dissous et du rôle de catalyseur de certains cations métalliques (par exemple les ions de cuivre) adsorbés à la surface de la pyrite. INTRODUCTIONThe copper industry is aware of the difficulties of floating Cu-Mo sulfide ores in seawater. Molybdenum recovery is partially depressed when lime is used to reject pyrite. In plant practice, sodium metabisulfite (MBS) has been demonstrated to be the most promising option for replacing lime in seawater."

Jan 1, 2017

By Alain Broussaud, Guy Fourniguet, Jacques Franck, Pierre Conil

Steady-state simulation is now in current use to assist mineral processing plant design and optimization. However, the reliability of results generated by simulators has not until now been seriously investigated. A simulator supervision algorithm was designed and programmed to study both the influence of the reliability of experimental data on the accuracy of unit operation model calibration, and the influence of unit operation model accuracy on the results of direct plant simulations. An application to a grinding flotation plant is described and discussed. The approach may open the way to the quantitative analysis of the risks taken in mineral processing projects, which would be similar to the application of geostatistics to mining projects.

Jan 1, 1990

By B. K. Shibler

As a part of the Bureau of Mines' intensive; 'investigation of domestic manganese deposits, ore-dressing studies were conducted on three samples of oxide and silicate manganese ores from various Wyoming properties. The samples wore as follows: 1. A 2-ton sample of ore was obtained by a Bureau engineer during examination of the Caulkins-McGuckin property in the center of Crook County, 10 miles north of Sundance, Wyo. The ore body was described as a vein deposit in rhyolite porphyry. 2. The J. B. C. Mining Co. submitted a 1-ton sample of oxide manganese ore from a property located 44 miles northeast of Rock River in Albany County, Wyoming. 3. A 1-ton sample of oxide-silicate-ore was obtained by a Bureau examining engineer from the Gheen property in the northeast corner of Washakie County, Wyo. The ore body was described as a replacement deposit in a country rock of silicified limestone. As the samples differed widely in physical and chemical characteristics and also in their response to methods of concentration, ore from each property was considered a separate ore-dressing problem.

Jan 1, 1949

By R Dimitrakopoulos, R Senécal

This paper presents a metaheuristic solution to the optimisation of open pit long-term production scheduling with a stockpile and geological uncertainty. The optimisation formulation is a two-stage stochastic integer programming (SIP) model that determines the optimal mining sequence that maximises the total discounted cash flow, while penalising for high deviations from production targets. A parallel implementation of Tabu Search is proposed to accelerate the solution of the SIP formulation and take full advantage of multicore computer processing. Different variants of the proposed algorithm are applied to a case study to assess the performance of the parallel approach. The proposed algorithm and variants are benchmarked using linear relaxation of the complete problem to determine robustness and provide a better overview of the related performance. The results show a net improvement over the sequential solution, and the new proposal seems to be promising when working with a large-scale data set.CITATION:Senécal, R and Dimitrakopoulos, R, 2014. Parallel implementation of a Tabu search procedure for stochastic mine scheduling, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 405–414 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By David F. Smith

[The U. S. Bureau of Mines at its Pittsburgh Experiment Station is frequently called upon to determine by laboratory tests the explosibility of suspensions in air of various dusts encountered in mines and elsewhere. Not all dusts which are combustible or contain combustible material will form explosive mixtures with air under ordinary conditions of temperature and pressure. They may not be highly combustible enough. They may contain a considerable amount of inert or non-combustible material or, the dust particles may not, be fine enough to form explosive mixtures. A knowledge off the chemical composition of a dust together with a determination of the size of the particles often gives valuable indications. But in many cases actual explosibility tests are necessary. Such a case is evidently that of powdered soap, whose explosibility hazard the Bureau was recently called upon to determine, Although an explosion which occurred in a soap plant as early as 1890 was attributed4 to powdered soap, it is apparent, due to the great number of inquiries received by the Bureau, that the hazard presented by powdered soap has not been at all generally appreciated. To the writers' knowledge, no extensive investigation of the explosibility of powdered soaps has been made. It is only recently that pure powdered soap has been manufactured on a large scale. The familiar "soap powder" in the past was usually a mixture of soap with a relatively large quantity of sodium carbonate. Often it contained large amounts of moisture and abrasive material. Even a highly combustible dust when mixed with large quantities of inert dust will not form explosive mixtures with air. Pure powdered soap, however, presents a different aspect. Pure soap is formed by combination of alkali (incombustible material) with fatty acid (combustible material). Toilet soap fray also contain a certain amount of glycerin and essential oil winch, being combustible influence the explosibility]

Jan 1, 1928

By Karl R. Becker

A variety of commercial detonators (fuse type and electric instantaneous and delay types) were subjected to impact and thermal stimuli to determine initiation stimulus levels and the dominant parameters in resistance to initiation. In the impact trials the detonators were impacted along their length to find the most sensitive region; threshold initiation limits obtained for these regions ranged from 3.47 to 20.82 joules (2.6 to 15.4 ft-lb). The friction sensitivity of the explosive component was an important parameter in determining sensitivity; various construction features of nonexplosive components played a role as well. In the thermal sensitivity trials, the detonators were heated from ambient to 100° C at an average rate of about 1.0° C/min, and thereafter at 0.5° C/min until they exploded; the explosion temperatures observed ranged from 121° to 188° C. These temperatures correlated quite well with the reaction temperatures of certain characteristic explosive components used by different manufacturers. The data also indicated an effect of confinement on explosion temperatures of detonators.

Jan 1, 1975

By R. S. Hutton

WHEN I had the honor of receiving an invitation to give the-Institute of Metals Lecture, it occurred to me that it might be of interest to review the advances which have been made in refractories, considering how important these materials of construction are in the carrying out of many metallurgical operations and what a large factor they represent in our costs of production. Frankly, I can claim no recent contact with the refractories industry and what little work I myself have been concerned with has been rather unorthodox in character. However, perhaps in consequence of this, I can approach the review without bias and include some suggestions which may prove stimulating or provocative to some of you, who have a more intimate knowledge of refractories and their uses than I Possess. It is neither possible nor necessary for me to survey the progress of industrial refractories, for this has been so thoroughly undertaken by others1-7 in recent publications. Perhaps the best way to get a broad picture of this progress is to compare the Faraday Society Symposium on Refractory Materials 20 years ago8, containing a report on one of the first attempts at standardized testing, with the American Society for Testing Materials Committee Report of February 1935. Suffice it to say, lest my provocative remarks be misunderstood, that I do appreciate that great advances have been made, particularly by companies that have established their own research laboratories and by universities and cooperative research institutes working for the common weal of groups of manufacturers or for national and international progress. The scientific study of the constitution diagrams of binary and ternary refractory oxides, which American workers have been foremost in under-taking, ? led by the work of the Geophysical Laboratory at Washington, has laid a firm foundation for the whole subject. It should be remem-bered, however, that to a much greater degree than with the constitution of metal alloys, the equilibrium conditions are so sluggishly arrived at

Jan 1, 1937

By Timothy J. Orr, Michael J. Beus, Frank T. Duda

The technology to enhance safety and control features for mine shaft hoists is being investigated by researchers at the U.S. Bureau of Mines (USBM). The objective of the research is to prevent injuries and fatalities related to hoist and elevator operations. Monitoring and controlling mine hoisting operations will allow hoist operators, inspectors, and maintenance personnel to increase their awareness of potentially dangerous situations and provide controls for safer operations. Process simulation and visualization software, real-time data sensing, and advanced programming techniques are being applied to this problem. Development of reliable and cost-effective sensors and data acquisition interfaces to monitor hoist loads and detect slack rope conditions is underway. Three-dimensional design software was used to visualize mine hoisting to enhance understanding of hoist operations. Quick Basic and Visual Basic (an object-oriented Windows interface) are being used for acquiring and processing hoisting data. Testing and evaluation of components are underway at USBM testing facilities. The resulting system will allow hoist personnel to assess critical operating parameters, such as hoist position, speed, acceleration, conveyance load, and rope tension.

By Sepulvedam Jaime E., Levi Guzmán Rivera

"Grinding media consumption rates and their dependence on key operating conditions in semiautogenous grinding mills is analyzed on the basis of a detailed mathematical model recently developed by Moly-Cop´s specialists which describes and takes into account the three primary media consumption mechanisms, namely: abrasion/corrosion, surface spalling and impact ball breakage. The influence of key mill operating conditions – such as ball filling, discharge grate opening, mill speed, lifter profile, and ball quality – on their corresponding grinding media consumption rates is explored via a variety of model simulations, discussing in every case the independent contribution of each of the indicated consumption mechanisms to the estimated total ball consumption rate.INTRODUCTIONA thorough understanding of the independent contribution of each grinding media wear mechanism is extremely important, especially in semi-autogenous grinding (SAG) operations where macrowear (spalling) and ball breakage cannot be ignored or neglected. The high impact conditions imposed in modern SAG milling environments has created serious challenges for grinding media manufacturers since their products must be able to perform with minimal breakage and surface spalling.GRINDING MEDIA WEAR MECHANISMFor SAG milling operations, at least 3 different mechanisms have been identified as the main contributors to the observed overall grinding media consumption, here referred to as: abrasion / corrosion, ball breakage and surface spalling.Wear by Abrasion/CorrosionThe abrasive/corrosive wear mechanism has been discussed in depth in previous publications (Benavente Hector, 2007; Guzman Levi, 2014; Sepulveda and Morrow, 2014). The most widely accepted approach to mathematically characterize the consumption (wear) kinetics of grinding media in rotary tumbling mills is known as the Linear Wear Theory (Prentice, 1943; Norquist, 1950; Sepulveda, 2004) which claims that—at each instant 't' after a grinding body enters the mill load—the rate at which the body loses weight is directly proportional to its surface area exposed."

Jan 1, 2016

By F. A. Crossley

The additions: o, Sn, Zr, Cb, Mo, and V were studied for their effects on the a/a + Ti3A1 boundary of Ti-A1 base ternary alloys. These additions were chosen because of their importance to commercial titanium alloy practice—oxygen as the major impurity (in terms of influence on mechanical properties) and the others as major alloying additions. The composition and temperature ranges of investigation varied according to the system as shown in Table I. The principal means of investigation was light-microscopy. The basis of the ternary studies was the recently determined titanium-rich end of the Ti-A1 system.' MATERIALS, METHODS, AND PROCEDURES Ingots were prepared in 15 g size for all alloys except those of the Ti-Al-Mo and Ti-A1-V systems which were prepared in 20 g size. These alloys were prepared from high-purity, electrolytically refined titanium obtained from the Bureau of Mines, Boulder City Metallurgical Laboratory, Boulder City, Col., and Chicago Development Corp., Riverdale, Md., for the 15 g and 20 g ingots, respectively. The alloying additions were obtained from commercial sources, and were at least of 99.9 pct purity, except the V-15 wt pct A1 master alloy for vanadium additions. This alloy was of 98.2 pct purity; the major impurities were 0.37 wt pct Fe and 0.38 wt pct Si. The ingots were prepared by multiple melting in a nonconsum-able-electrode arc furnace. The ingots were covered with Markal coating "CR-T22" (Markal Co., Chicago) to protect them from scaling. Markal coating is applied as a slurry of solids in a volatile carrier liquid. The coated article is air dried. Upon heating to the hot working temperature the coating fuses to form a glassy, protective film. The ingots were heated to 1000°C and rolled to 0.16 in. thickness, reheating after each pass. The glassy film was removed by sand blasting. Ten mils were removed from all surfaces by grinding and/or pickling (3 pct HF, 30 pct HN03, balance water). Grinding was always followed by pickling to remove traces of the grindmg medium. Hydrogen removal was accomplished by vacuum annealing at 1000°C for 2 hr to a final pressure of about 0.02 µ Hg. This was followed by annealing in evacuated Vycor bulbs (800°C, 2 hr, ice brine quenched (IBQ)) in order to maximize ductility. The materials were then lightly pickled and cold rolled to 0.12 in. thickness or cracking, whichever occurred first. After rolling, 1/2 by 1/4 in. specimens were cut for the equilibration anneals given in Table 11 and carried out as previously described.1 Final polishing of the specimens for metallographic examination was done by electrolytic means. Specimens were first examined without etching under bright field and polarized light illumination, for this is the only means of detecting the "two-phase" phenomenon.1,2 The term "two-phase syndrome" refers to Ti-A1 al-loys which appear on the bases of their chemical, phys-ical, and mechanical properties, to be two-phase, but are actually single phase and inhomogeneous in composition. Since processing and heat treatment of the alloys of the first group were completed before the two-phase syndrome was discovered, a number of the specimens were found to exhibit this phenomenon—80 pct of those of the Ti-Al-Zr system, 5 pct of those of the Ti-Al-Sn system, 30 pct of those of the Ti-Al-Zr system. The affected specimens were homogenized by heating above the ß transus temperature and quenching. The heat treatment and working schedules to accomplish this are given in Table 111. After rolling, specimens were pickled (3 pctHF, 30 pct HNO3 in water) to remove 1 to 2 mils from the

Jan 1, 1970

By H. J. White

Haynes International, a world leader in the manufacture and production of nickel, and cobalt base alloys has invented and developed a low cost high temperature material, with a unique combination of superior oxidation resistance and weldability/ fabricability. HAYNES® HR-224TM (Ni ? 27.5Fe ? 20Cr ?3.8A1 ? 0.3Si ? 0.3Ti) forms a planar/ continuous/ adherent aluminum oxide film at high temperatures which has been shown to effectively limit chromium poisoning in solid oxide fuel, cell, systems. A 20,000 pound vacuum induction melted (VIM) + electroslag remelted (ESR) heat has been melted and converted into various product forms: sheet, plate, bar, welded tubing, wire, etc. The alloy was designed for service in severely oxidizing environments recuperators, automotive catalytic converters, wire strand annealing furnace tubes, etc. and has been of great interest to solid oxide fuel, cell, manufacturers as a materials of construction in balance of plant (BOP) design. This manuscript presents the physical, properties, mechanica, properties, and oxidation resistance of the alloy compared to other materials being considered for solid oxide fuel, cell, design

Jan 1, 2010

By R. Jackman, D. Koningen, G. Wilcox

"Gowest Gold Ltd. is in the process of developing the Frankfield East gold deposit located along the largely undeveloped Pipestone fault northeast of Timmins, Ontario. In addition to resource development and environmental permitting work the company has had an ongoing program of metallurgical and engineering studies aimed at evaluating options for processing the Frankfield East ore. Mineralization at the Frankfield project contains arsenopyrite and pyrite as the major sulphide minerals. Bulk flotation of all sulphides results in extremely high gold recovery. However, the gold is almost entirely associated with the arsenopyrite fraction of the ore and is refractory in nature requiring preoxidation treatment. Selective flotation was investigated to recover a gold-arsenopyrite concentrate thereby reducing the mass which would be subjected to further gold processing. As part of this work, a pyrite concentrate low in arsenic content was also recovered that would be suitable as a source of sulphur for a smelter (or other pyrometallurgical facility). Production of separate arsenopyrite and pyrite concentrates is frequently examined but rarely adopted due to the distribution of gold between the two products or the inability to achieve adequate separation. Several flowsheet options were investigated in the study. The best results were achieved following a sequential flotation flowsheet. The flowsheet configuration was key to meeting the targets for the two products. In this paper, the various options investigated are reviewed and the results of the final flowsheet are presented. The overall plan by Gowest was to evaluate all process options to bring the Frankfield East deposit into production. The ability to effectively separate the arsenopyrite and pyrite components in the ore provides Gowest with added opportunities to pursue both short and long term production scenarios."

Jan 1, 2012

By D P. Yang, Yang R. G

The laws of throwing and heaping of engineering blast are important for making use of throwing and heaping of thrown body to form certain shape, such as building dams by directional blast. The article is to apply Ballistic theory of single thrown body to take the throwing course of thrown body as the movement of particle system, and then delimit the total of thrown body into units of thrown bodies, and regard the heaping shape of single thrown body as a perfect triangle, and found a quantitative relation between macro-geometry parameters of perfect triangle and designed parameters of explosives. The theory has been adopted in blast practice and gotten good effects.

Jan 1, 1999

The Stawell Goldfield, the westernmost of the main Victorian fields, has produced over a million and a quarter ounces of gold from one and three-quarter million tons of ore. The lodes are quartz reefs and sulphide bodies occurring in sediments of lower Ordovician or upper Cambrian age. The lodes are confined to a relatively narrow suite of weak rocks lying between stronger ones above and below and there is a definite relationship between fold structure, pitch and strength of folding and ore.LOCATION HISTORY AND PAST PRODUCTIONThe town of Stawell, situated 150 miles north-westerly from Melbourne on the main railway and road to Adelaide, is the most westerly of the main gold areas of Victoria. Alluvial gold was found at Pleasant Creek (now Stawell West) in 1853 and the usual "rush" followed. Numerous alluvial leads, some surface, others buried under up to 100 ft. of Tertiary sediments were worked. The alluvial gold was soon exhausted, but in 1857 gold-bearing reefs were found on the slopes of a prominent ridge on the northern edgeof the present town. Early reef mining was by small working parties mining to shallow depths only and treating their ore at public crushing plants. Some of the early returns were very high grade. The next stage was the amalgamation of claims and the formation of companies, with their own treatment plants. This stage continued till the last mine closed in 1921. These companies had, by present standards, small holdings and far too many shafts were sunk, resulting in less efficient prospecting and operation.Since 1921 there have been one or two small scale attempts to revive mining but without success. Of recent years Gold...

Jan 1, 1960

This Department handles all ores prior to blast-furnacing, the object of the operations being to mix the lead-bearing material with fiuxes, eliminate sulphur from the mixture, and produce a homogeneous sintered product which is chemically and physically suitable for treatment in the blast furnaces.During the financial year ended the 30th June, 1937, the tonnage of charge treated was 458,960 tons, containing some 183,470 tons of lead and 8,504,000 oz. of silver.The quantities of the principal components of the charge treated were as follow:-

Jan 1, 1937

By O. Q. Leone

A processing unit was developed for the complete cleaning of titanium alloy chips. The process uses solvent degreasing, magnetic separation, and anodic solution of nonmagnetic impurities in 10 weight-percent sulfuric acid. Vacuum arc-melted ingots weighing approximately 10 pounds each were prepared from cleaning chips according to ingot specifications.

Jan 1, 1973

A new analytical approach for characterizing and improving the performance of ball milling is presented. Individual ball mill circuit design and operating variables can be related to overall circuit performance through two distinct parameters for classification and breakage. The ball mill circuit functional performance equation is presented. Applications in the industrial plant and in the research field are discussed.

Jan 1, 1990