Search Documents

By Sidney Fischler

Large striation-free single crystals of bismuth have been grown from the melt by rapid freezing. Zone-refined bismuth, together with doping impurities if desired, is placed in a shallow flat-bottomed graphite boat and melted in air with a propane hand torch. The torch is then withdrawn in a manner which causes the melt to freeze direction-ally. Crystallization, which resuires only a few minutes, usually results in the formation of a single crystal even when a seed crystal is not used. Crys -tals of any desired orientation may be grown by using oriented seeds. Undoped crystals grown by this method have residual resistivity ratios greater than 200. THE growth of large single crystals of bismuth by either the Czochralski or horizontal zoning technique is not entirely satisfactory. Specifically, difficulties are encountered in producing single crystals of the required dimensions in all desired orientations, and striations caused by low-angle polysynthetic twins are frequently present in the crystals. In addition, both methods are time-consuming and require special apparatus of some complexity. A simpler method has now been developed for growing large striation-free bismuth single crystals of desired orientation in a short time. Fig. 1 shows a typical setup consisting of a rectangular graphite boat which contains zone-refined bismuth, a 1/8-in.-thick flat quartz plate which covers the entire inner bottom of the boat, and three additional quartz plates about 1/4 in. thick which are used to separate the bismuth from the graphite everywhere except at a small area at the left of the boat. The graphite boat is 1 in. high, and its sides and bottom are about 1/8 in. thick. The quartz plates should be smooth and clean. The graphite boat is heated from the right with a propane torch, as shown in Fig. 1, until the bismuth is completely melted. The melt has the shape of a triangle with a narrow neck at the apex farthest from the torch. The melt is frozen direc-tionally by gradually moving the torch toward the right, away from the boat. The bismuth in contact with the graphite, at the left end of the neck, freezes first. The freezing interface then moves down the neck into the main bulk of material, where it develops a convex shape ideal for the continuation of single-crystal growth. The interface continues to move through the melt until the entire bulk is solid. The entire procedure may be completed, in air, in a matter of minutes. The technique described almost always yields a single crystal whose basal plane is nearly perpendi,cular to the bottom of the graphite boat. In earlier experiments, in which the bottom of the melt was in direct contact with the graphite boat, single crystals were grown with basal planes parallel, perpendicular, or at some intermediate angle to the bottom of the boat. At times the orientation of the bulk of the material differed from the orientation of the material in the narrow neck. In these cases, a nucleation site initiated the growth of a differently oriented crystal, and the thermal conditions favored the new orientation over the initial one. The thermal conditions depend on a number of factors, including the heating technique, the placement, shape, and thickness of the quartz plates, the thickness of the walls and bottom of the graphite boat, and the quantity of bulk bismuth employed. All of these factors, plus the initial orientation and the presence and effectiveness of nucleation sites, will determine the orientation of the final large single-crystal slab. When a crystal of specific orientation is desired, an oriented section of a rapid-freeze crystal is shaped by spark cutting and grinding for use as a seed. To grow a doped crystal, the desired impurity is placed in the graphite boat together with the bismuth chunks and seed. Crystals doped with mercury, cadmium, lead, and selenium have been grown. The rate of freezing is so great that the distribution coefficient of any impurity approximates unity. On a gross scale, therefore, impurities should be more homogeneously distributed in rapid-freeze crystals than in Czochralski or zoned crystals. Because of the possibility of constitutional supercooling, however, it is quite possible that impurities are not homogeneously distributed on a microscopic scale in the rapid-freeze crystals. Generally the single crystal slabs which have been prepared are initially 5 to 7 mm thick. Thicker crystals may be obtained by using one of these slabs as a seed. The slab is placed in a graphite boat resting on a large aluminum block, either air- or

Jan 1, 1964

By P. J. Spencer, J. N. Pratt

The vapor pressure of manganese over liquid Mn-Sn alloys has been determined by a high-temperature torsion-effusion technique. Alloys containing from 8 to 100 at. pct Mn were investigated in the temperature range jrom 1280" to 1580" and the measured pressure values were used to calculate the partial and integral thermodynamic properties of the liquid alloys. The activities show small negative departures from ideality while the integral heats and excess entropies of mixing are asymmetric inform, changing from positive to negative with increasing manganese content. The possible contribution of various factors to the observed thermodynamic properties is discussed. COMPARATIVELY few thermodynamic data are available for manganese alloy systems.' Therefore, as part of a continuing program of studies of the thermodynamic properties of transition metal alloys, measurements have been made on various binary alloys involving this element. In recent publications,2~3 investigations of liquid Mn-Cu alloys and of the Mn-Au system in both solid and liquid states have been reported. For the first-mentioned system the work suggested that magnetic interactions may be responsible for the observed form of the thermodynamic properties, while in the second the influence of the electrochemical factor appears to be dominant. The present paper describes a similar study of liquid Mn-Sn alloys. Again the thermodynamic properties have been obtained from vapor pressure measurements made by use of a high-temperature torsion-effusion technique.4 A detailed description of the apparatus and of the experimental procedures used in alloy preparation and pressure measurement may be found elsewhere.2'4 EXPERIMENTAL RESULTS Sixteen alloys, ranging in composition from 8 to 100 at. pct Mn, were prepared from spectroscopically standardized manganese of 99.99 pct purity and tin of 99.999 pct purity, both supplied by Johnson-Matthey and Co., Ltd. One-gram samples of the alloys were obtained by carefully weighing appropriate amounts of the pure components into an effusion cell; this was then suspended in the apparatus and the metals melted together in situ by heating under vacuum to approximately 1550°K. After allowing sufficient time for a homogeneous liquid alloy to be formed, vapor pressure measurements were commenced. These were determined as rapidly as possible at a series of steady temperatures within the range of interest. The duration of experimental runs on individual samples was kept sufficiently short to ensure insignificant varia- tion of alloy composition during investigation. After completing pressure measurements, the alloys were rapidly cooled and their compositions checked by weighing or chemical analysis. All experiments were conducted using effusion cells machined entirely from boron nitride. Measurements were made using a variety of cells with orifice areas ranging from 0.0032 to 0.0075 sq cm and lengths of the order of 0.04 cm; the usual effusion correction factors for orifice geometry and molecular distribution were calculated using Freeman and Searcy's equation5 and had values between 0.6 and 0.75 for the orifices employed here. The vapor pressures of manganese over the alloys were measured at approximately 20°K intervals in the temperature range 1280" to 1580°K. In view of the close approximation of the measured pressures to Clausius-Clapeyron behavior in the experimental temperature range, the data for each alloy have been expressed by equations of the form: logp(atm) =-A/T + B A least-squares computer treatment was applied to the vapor pressure values in order to obtain the coefficients A and B with their associated error. The resulting equations are listed in Table I, together with the equation for pure solid manganese obtained from a previous study.4 To minimize the effect of possible apparatus calibration errors, the activities and partial free energies of manganese in the alloys were calculated by initial reference to the latter equation, obtained from identical torsion-effusion measurements. The immediately resulting thermodynamic quantities, based on a solid manganese reference state, were then converted to refer to the more appropriate supercooled pure liquid manganese standard; tabulated values of the free energies of solid and liquid manganese from Hultgren et al.' were used for this purpose. Partial entropies of solution of manganese were calculated from the temperature coefficients of the free energies and partial heats from the Gibbs-Helmholtz relationship.

Jan 1, 1969

By Robert M. Semple, Harvey W. Parker

INTRODUCTION Two promising innovative tunnel support systems are being developed by the Civil Engineering Department of the University of Illinois. One of these is a lining which can be placed by a slipform located immediately behind and contiguous with a tunneling machine. Recent advancements in construction materials appear to provide the breakthrough required to make such a system feasible and practical. The lining material which permits this construction scheme is wire fiber reinforced concrete made with high, very early strength regulated-set cement. Parts I and II of this paper relate to this slipformed liner. Part I discusses the material and equipment required to install the liner. The "Extruded Liner System" (ELS) has been devised to place the lining. This ELS concept is briefly described and a tentative development program is outlined. In Part II, the physical properties and practical construction aspects of the liner material are discussed and a program for structural testing of 10-ft diameter prototype tunnel supports is presented. Part III contains descriptions of improvements to conventional steel-rib tunnel supports. It is shown that square tubular box sections are structurally superior to wide flange sections for complex loading conditions often encountered in rock tunnels. Analytical studies and tests on connections have been performed to evaluate their structural behavior. These are presented along with a program for comparative large-scale tests on horseshoe-shaped frames with a 10-foot span. This research is being conducted by the Department of Civil

Jan 1, 1997

By Peter D. Bell

The paper describes the geology of the gold deposits of the Yanacocha district, Northern Perú. The Yanacocha District is located 20 km north of the city of Cajamarca, whose deposits are located in the Andes of norther in Perú. Gold production may have occurred as early as Incan times, but modern exploration that began in the 1960’s targeted only copper and silver. Current mining is entirely by open pit methods with heap leach recovery. Production in 2003 was from the Cerro Yanacocha deposit and the La Quinua fluvioglacial deposit. La Quinua is not discussed in detail in this report. However, Yanacocha is described as a high-sulfidation epithermal deposit occurring in pyroclastic rocks. The success of Yanacocha has made this type of target among the most sought after by exploration companies worldwide. The important characteristics of the geology of Yanacocha are reviewed below, along with some specifics of exploration techniques used in the district.

Sep 12, 2005

By Jeon Jeon, Yong-Kun Choi, Chung-In Lee, Yong-Hun Jong, Hag-Soo Kim

In this study, a computer program to design tunnel blasting pattern has been developed. The program consists of two parts; one is for tunnel blasting pattern design and the other is for blasting modeling to estimate the peak particle velocity, the distribution of fragmentation and the excavation damage zone. We modified the design method of tunnel blasting pattern suggested by Langefors because it provided undesirable pattern in blasting practices such as considerably large center cut and too large burden for Vcut as drilling length increased. As a result, the burden and spacing were reduced to practically appropriate amounts. In addition, the correlation between rock mass rate, RMR, and rock constant in blasting, c, was analyzed based on the data collected from twenty three tests of tunnel blasting. It was concluded that the correlation between them was fairly good enough to be applied in cut design. In order to check the validity of the modified methods and their practical applicability, test blasting was carried out at two different tunnel construction sites in Korea. The results were satisfactory in that the average rate of advance was 90% and the overbreak did not cause additional support. Futhermore, the developed program is capable of estimating peak particle velocity by using (a) the existing vibration equations, (b) the vibration equation obtained by test blasting to check out the practical applicability of the designed blasting pattern. Feedback is implemented into the program to adjust the designed blasting pattern and control the vibration.

Jan 1, 2005

By R. W. Amstutz

Abstract. The shaft was drilled on U.S. Government land in the Piceance Creek Basin and was funded by the U.S. Bureau of Mines. It was drilled to 723 meters (2 371') to provide access to rich deposits of oil shale, nahcolite and dawsonite for geotechnical test work and environmental mining research. Rotary drilling and dual string, reverse-air, jet-assist circulation methods were used. Drilling required 8 months. Site preparation, running and cementing the casing required another 4 months. A 2.44-meter (96-inch) ID steel welded casing, 5.1 cm (2 inches) thick was installed and 2 700 tonnes (63 000 sacks) of cement were slurried and pumped into the annulus.

Jan 1, 1980

By Peter V. Barr

Despite the advent of modem firing control systems reheating furnace operations frequently allow significant thermal excursions in the discharged slabs or billets after furnace delays. Although HSM furnaces are not immune to this and other related problems, mini-mill operations are most vulnerable due to their more frequent delays and (often) less sophisticated control systems. In order to reduce these problems control systems will commonly include a thermal model, operating either on-line (interacting directly with the controller logic) or in an advisory, off-line mode. Using a new 'fast' thermal model, the paper examines the thermal response of a typical mini-mill furnace during both delays and the subsequent recovery period. A variety of firing strategies are explored and compared on the basis of maintaining thermal excursions within allowable limits for rolling. Other factors, such as the potential for overheating of billets within the furnace during delays and the overall thermal state of the furnace, are also considered in some detail. Although common practice, the use of conventional thermocouple zone temperatures for furnace control during and after delays is shown to be a dubious proposition. Keywords: Reheat Furnace, Modeling, Process Control

Jan 1, 2003

By Pedro Delvasto, José Lezcano, Marcos Garayar

En el presente trabajo se tomaron 13 muestras de aguas y suelos en sitios afectados y sin afectar por la actividad minera, en un ambiente minero real del altiplano peruano, específicamente en el Tajo Anama de la minera Anabi S.A.C. ubicada en el distrito de Huaquirca, provincia de Antabamba, Departamento de Apurímac. Se diferenció entre muestras afectadas directamente por la actividad minera (tajo) y muestras provenientes de zonas no sometidas a la actividad minera (entorno natural), pero dentro de las inmediaciones de la mina.

Sep 29, 2023

By Carrol A. Quam

DURING the first years of operation of the titanium and iron mine of the National Lead Co. at Tahawus, New York, efforts to increase production were hampered by the increased load put on the facilities for sharpening churn-drill bits. The ore and rock are extremely hard and abrasive and it was necessary to sharpen and harden a large number of bits per day to keep the churn drills supplied. Efforts to increase the capacity of the bit shop by a two-shift operation were not wholly successful in that it was hard to train men to do a satisfactory job of sharpening and tempering the bits. The number of bits that were improperly tempered increased, thus boosting the daily requirements for bits at the drills and increasing the load on the bit-sharpening facilities.

Jan 1, 1949

By J. A. Finch, D. Lin

The robustness of the large-sections correction procedure, Hill's fast approximation, Barbery's correction and the PARGEN correction was examined by comparing their ability to reconstruct the true liberation distribution using sectioning data from computer-generated spheres. The results indicate that the flexibility of a correction procedure is related to the assumptions it makes about the continuity of the liberation distribution, locked-particle characteristics and ore texture. Overall, the large-sections procedure appeared to be the most generally applicable. The Hill fast approximation performed well, but this was probably because it partially incorporates the sphere model; the performance of the PARGEN and Barbery corrections varied from case to case.

Dec 1, 1995

By Dong Liang, Honggang Zhong, Zhenxing Yin, Qijie Zhai

"2507 super duplex stainless steel (SDSS) has been widely applied in a marine environment, attributing to its excellent pitting corrosion resistance and mechanical properties which are particularly determined by the nitrogen precipitation behaviors and volume fraction of ferrite. In this paper, various cooling rates were obtained by applying four different moulds with the common gating system. By which the influence of cooling rates on nitrogen precipitation behaviors and the ferrite fraction in cast 2507 SDSS was comparatively investigated. The results showed that nitrogen porosity could easily precipitate in cast 2507 SDSS under standard atmospheric pressure. The number of nitrogen holes increased with decreasing the cooling rates, and the holes mainly distributed in three zones, i.e. the interface between the horizontal and vertical columnar grains, top vertical columnar grains and the final solidification region. Additionally, higher ferrite fraction was obtained with lower cooling rates.IntroductionDuplex stainless steels (DSS) have a dual-phase microstructure consisting of ferrite (d) and aus-tenite (?). Due to the combined advantageous properties of d and ? phase, their application rapid-ly increased in industry [1, 2]. Super duplex Stainless Steel (SDSS) is the third generation of du-plex stainless steels, of which the alloy elements Cr, Ni and N content are higher than the stand-ard 2205 DSS. Because it has high contents of alloy elements, the SDSS has better mechanical properties, and its pitting resistance equivalent number (PREN) reached a point 43. Hence SDSS has been used in petroleum chemical industry, the marine equipment and harsh corrosion environments [3]. SDSS contains ferrite stabilizing elements, such as Cr, Mo and Si, and austenite stabilizing elements like Ni, Mn and N [4]. Many researchers have studied the effects of these elements on the stabilization of d and ? phase and the ratio of the two phases. High nitrogen con-tent is another prominent feature of SDSS. Nitrogen addition to SDSS is very effective for improving its mechanical properties [5] and corrosion resistance [6], such as pitting resistance in NOx environment. To increase the nitrogen content in steels, a lot of work had been done. N. Nakamura and S. Takaki [7] examined the behavior of nitrogen absorption in Fe-23Cr alloy powder by sintering in nitrogen gas atmosphere, they found nitrogen content easily up to 1.0 wt. %. Using devised NH3 gas injection system, W. Park et al. [8] successfully produced austenitic Fe–23.5Cr alloys containing over 3 wt. % of nitrogen. Further-more, W.P. Tong et al. [9] stated that nitrogen percent was extraordinary high (about 10 wt. %) in pure iron plate. However, the above methods are difficult to be applied to large-scale industrial production."

Jan 1, 2012

By Hillary W. St. Clair

This report gives the results of an experimental study of the progressive changes that occur in particle size and size distribution when a homogeneous and isotropic mineral is subjected to crushing by impact. The mineral used in the study was uniformly sized quartz, which was crushed in a simple drop¬-weight machine that applied impact energy up to about 100 kg-cm per g. Screen analyses of the crushed products were analyzed by the method of moments to determine the mean size, variance, skewness, and kurtosis. Analysis of the data from these experiments shows that the mean size of the crushed product is a function of the energy input and the initial size. The size distribution is functionally related to the degree of size reduction. As the mean particle size is decreased, at first there is a corresponding increase in the variance and decrease in the skewness, But, as size reduction is carried further, each tends eventually to approach a steady value, and the form of the size distribution becomes stable.

Jan 1, 1972

By Vladimir P. Nebera, Kostas A. Matis, Piotr M. Solozhenkin, Anastasios I. Zouboulis

"Considered combination of two processes-selective sorptions of metals on biosorbents, inorganic sorbents and their following flotation by dissolved air(DAF). The process of biosorption, using as sorbent suspended non-living biomass (of Streptomyces genus, S. clavulgerus and S. griseus, fungi-Penicillium chrisogenum and Phizopus arrhizus, active slime) in fine particulate dispersion, combined with the application of flotation, for the consequent solid / liquid separation of metal-loaded biomass, has been studied for the removal of toxic and noble metals from dilute aqueous solutions. Biomass of microorganisms possesses great sorptive capacity, exceeding capacity of synthetic and natural sorbents. For instance, Micrococus luteus sorbed gold for 2h Au 253mg/g.The optimal conditions of effective flotation (more than 90%) of actinomyces biomass, loaded with toxic metal-cadmium were found. The adsorpbing flotation technique for copper, arsenic (III, V), chromium removal of metals on pyrite mineral fines (suitable industrial by- product) is an effective process.Dissolved-air flotation was also apllied in the case of dolomite/lead aggregates removal. A fatty acid was used as a flotation surfactant. The presence of dolomite fines aids the efficiency of the process, in comprarison with the flotation of alone lead hydroxide.A laboratory investigation was undertaken on the gold-thiourea system over the whole pH range, aiming at the separation complex of gold [Au(CS(NH2)2]2+ by flotation from dilute solutions. The reagents were found to improve gold recoveries remarkably: the recovery reached over 95%. A separation technique has been investigated, involving gold adsorptionon powdered activated carbon. Foam flotation was employed for the subsequent solid/liquid separation, using sodium oleate as surfactant. The content of Au were 500 mg/L in froth and recovery gold about 100%."

Jan 1, 2003

By Y. Suzuki, J. Nagao, Y. Ueda, K. Shimokawa

"A Ti- Ni intermetallic compound could be formed rapidly from Ti and Ni powder compact with SHS process. Microgravity experiments using a drop shaft are carried out, This report shows the effect of microgravity or high gravity on formability of an intermetallic compound. It is concluded that the specimen forms a porous and nearly amorphous alloy by rapid cooling under microgravity but with rapid cooling under high gravity after microgravity, the specimen forms a uniform and dense structure with better crystallinity.IntroductionTi - Ni inter1etallic co1pounds have been produced and have beco1e si1ilar to the a1orphous and porous structure as a result of the SHS (Self Propagating High-te1perature Synthesis) process under 1icrogravity. SHS process is being applied to the synthesis of cera1ics and inter1etallic co1pounds (1). The technique is characterized by a large a1ount of heat being emitted within a very short ti1e interval as regards the sistering reaction. One SHS process, acco1panying 1elting by a reaction was observed, and that was due to the quick heating of a Ni-Ti co1pact containing 50 ato1ic percent of Ti under a low pressure (2-4). In this report, we have researched the use a drop shaft which is 1ore effective during a short ti1e under 1icrogravity and high-gravity, so as to obtain high dense speci1ens with the exception of porous specimens (5). Mechanical properties of each specimen were esti1ated from these 1icro-structures with a discussion about the effect of changing gravity regarding 1elting and solidification of the Ti-Ni intermetallic comounds."

Jan 1, 1996

By S. Dereski, G. Chancellor

"INTRODUCTION Barrick Goldstrike underground mine is located in Northern Nevada on the Carlin trend. The underground mine produces approximately 1.5 to 1.8 million tons a year and approximately 400,000 ounces of gold a year. The mine is comprised of two main mining methods, underhand drift and fill and long hole stopeing. The mass blast project stated in 2012 as Value in Use project between Barrick, Southwest Energy and Orica, the goal of this project is to be able to blast an entire drilled stope in one blasting event instead of taking multiple blasts. This will improve productivity by eliminating intermediate blasts, reducing additional blast time, eliminate drill hole cleaning due to the previous blast. Project implantation started in the fourth quarter of 2013 and mass blasting has been common practice throughout all of 2014. STOPPING PRACTICE AT GOLDSTRIKE BEFORE MASS BLAST PROJECT The production from the Goldstrike mine is approximately 70% from stopes. The timely completion of all stoping blocks is imperative to maintaining the plan, delays in the execution of any particular block can have detrimental ripple down effects as neighbouring stoping blocks become delayed. Before the implementation of this project the standard practice for Goldstrike was to: 1. Drill the entire stope 2. Blast a bottom shot, normally between 10 feet and 20 feet off the bottom of the slot rings. This would be mucked out before the next shot 3. Blast a pull through shot, this included the raise and one or two production rings. Again mucking this out before the next shot 4. Blast production rings, one or two more blasts depending on stope size. In most cases between each of these blasts the holes in the other rings of the stope would have to be cleaned. This meant either cleaning manually using air and water, or mechanically cleaning with a bench drill. In many cases this resulted in delays in completing the stoping block."

Jan 1, 2015

By M. Rahmanpour

"Mine planning is a multidisciplinary procedure that aims to guarantee the profitability of a mining operation in changing and uncertain conditions. Mine plans are normally classified as long-term, intermediate-term, and short-term plans, and many factors affect the preciseness of these plans and cause deviations in reaching the objectives. Commodity price is the heart of mine planning, but it has a changing and uncertain nature. Therefore, the determination of mine plans in the presence of uncertain mineral price is a challenge. A robust mine plan reduces the risk of early mine closure. A procedure is presented to determine the value at risk (VaR) in any possible mine planning alternative. VaR is considered together with downside risk and upside potential in order to select the most profitable and least risky plan. The model is tested on a small iron ore deposit. IntroductionMining projects are normally evaluated with the objective of maximizing economic value, as measured by the net present value (NPV). The aim of mine planning is to develop a yearly extraction plan that guides the mining operation to the highest NPV (Dagdelen, 2007; Yarmuch and Ortiz, 2011). This plan considers the technical constraints such as blending requirements, block sequencing, and pit slope (Caccetta and Hill 2003). Thus, the mine plan affects the economics and the payback period of mining operations.Mine planning is a procedure based on which the profitability of the mining operation is guaranteed in changing and uncertain conditions (McCarter, 1992). However, conventional mine planning ignores the volatility and uncertainty of future commodity prices and does not allow for managerial flexibility. It is common practice to assume a deterministic and constant commodity price through the mine life. The problem with this approach is that the commodity price is the heart of the mine planning procedure and governs the profitability and feasibility of the operation; thus ignoring price volatility will result in a sub-optimal mine plan."

Jan 1, 2016

By Mario Dobrilovic, Zvonimir Ester, Vinko Skrlec, Vjecislav Bohanek

The first public garage in the city of Dubrovnik has been built in highly urbanized area, on location Ilina Glavica. The excavation of the building pit has been done partly by construction machinery, i.e. by hydraulic hammer for excavations and partly by drilling and blasting. In the vicinity of the building pit there are houses, buildings and two schools. Drilling operations and blasting have been performed during the working hours while regular school classes have been held and activities in other buildings took place. The nearest structures are some 5 to 10 meters (16.4 to 32.8 ft) away from the building pit, which makes it even more difficult to perform blasting operations in the urban environment. For the purpose of determining safe and permissible oscillation velocity limits, i.e. the proportion of seismic effects of blasting, a trial blasting has been conducted. The permissible mass of explosive charge has been determined by original method respecting the requirements of existing standards (ISO 4866, DIN 4150, US BM 8507), which determine the permissible oscillation velocities in relation to their frequencies. According to measuring results of the oscillation velocity during the test blasting the design parameters of blasting field have been corrected and zones have been established within the excavation area considering the possible effect of blasting to the building pit environment. Further blasting operations have been performed in stages, in smaller blasting fields with deck charge within a blast hole while respecting the requirements of the transport possibilities for the blasted rock mass within the building pit and performance of control measurements of oscillation velocity for each blasting. Through application of all the protection measures, design solutions and systematic control of performance of activities the complete excavation by blasting has been completed without any damage on neighboring structures/buildings. This article presents these solutions and methods for reduction of seismic impact of blasting to the environment.

Jan 1, 2009

By K. Morita, N. Sano

Thermodynamic properties of chromium oxides in molten slags are very important for optimization of stainless steel refining processes as well as reduction processes of chromium ores. The solubility of chromite into molten slags has been found to vary considerably with oxygen partial pressure and slag composition in former studies by the authors. In the present study, activity data and redox equilibria of chromium oxides measured under moderately reducing conditions, PO2= 6.95x10–11atm, at 1873 K are summarized. For the CaO-SiO2-CrOXsystem, the activity coefficient of chromium oxide increased with increasing basicity, and the optimized slag composition for stainless steel refining is assessed as that saturated with CaCr2O4and Cr2O3usingthe phase relations determined. On the other hand, the presence of MgO and Al2O3brings about different behaviour of chromium oxide activity and redox equilibiria and the 44 mass per centCaO-39 mass per cent SiO2-11 mass per cent Al2O3-6 mass per cent MgO slag is recommended toreduce the chromium oxidation loss in the practical stainless steel refining process at 1873 K. Keywords: chromium, activity, stainless steel, AOD, VOD, oxidation loss, redox, CaO-SiO2-Al2O3-MgO slag

Jan 1, 2004

By A. H. Warner, G. A. Morrison

"INTRODUCTION The brown-iron ores of the Western Highland Rim of Tennessee extend north and south across the State for 115 miles. Many prospects of iron ore are known in this area.The district is credited with an output of 8 million tons of washed ore prior to 1930. Records on past shipments of ore indicates that the grade was probably 45 to 50 percent iron, 0,7 to 1.25 percent phosphorus, and 10 to 21 percent insoluble.As part of a survey of the iron resources of the Appalachian area, the Bureau of Manes began exploration .of the Churchwell and Robinette properties April 16, 1945, and continued until July 25, 1945, during which time 122 feet of test pits were sunk and 667 feet of churn drilling was completedPROPERTY AND ACCESSThe Churchweil property and that part of the Robinette tract north of U. S. Highway 64 are reported to be owned by the heirs of William Millsaps.The Churchwell property is northeast of Waynesboro, the county seat of Wayne County (fig. 1), and is east of Forty-Eight Creek, between Duggar Branch on the north and Little Forty-Eight Creek on the south.The property is reached from Waynesboro by traveling U. S. Highway 64 east 8 miles to Forty-Eight Creek, thence north on a secondary road 2 miles, to where Little Forty-Eight Creek joins it, thence by an old logging road up the hill half a mile to the property.The Robinett tract lies 1 mile southeast of the Churchwell and is reached by traveling east from Waynesboro on U. S. Highway 64 and a distance of 6.7 miles, and then turning left on an old logging road and following the ridge 2 miles to the prospect."

Oct 1, 1946

By A. P. Gize, J. F. W. Bowles, D. J. Vaughan, S. J. Norris

Paper presented at the IAGOD international symposium on mineralization related to mafic and ultramafic rocks held in Orleans, France, 1-3 September 1993. Geological evidence from tropical laterites indicates clearly that platinum group metals are taken into solution and precipitated to form grains larger than those in the source rocks. Platinum and palladium move differentially in the surface environment, with Pt partitioning into soils and eluvial or alluvial deposits while Pd remains more mobile in natural waters. Natural organic acids, particularly humic acid, can interact with platinum-group elements and concentrate them even in areas where their content in rocks is very low. Experimental work has confirmed that Pt and Pd can be taken into solution by humic acid at room temperature and in geologically short time-spans. Solubility and deposition may be controlled by physicochemical conditions, reaction kinetics or an adsorption effect, or there may be two competing reactions, solubilisation assisted by organic matter and a kinetically slower metal precipitation

Apr 1, 1994