Search Documents

By Oleg Ostrovski

Industrial pyrometallurgical processes in ferrous metallurgy are based on carbothermal reduction of metal oxides. Carbothermal reduction of stable oxides requires high temperatures. Lowtemperature reduction can be implemented by using methane-containing gas with high carbon activity, or by carbothermal reduction under reduced CO partial pressure. Under standard conditions, methane is thermodynamically unstable above 550 °C and decomposes to solid carbon and hydrogen. At appropriate CH4/H2 ratio and temperature, carbon activity in the methane-containing gas phase can be well above unity relative to graphite, which provides favorable thermodynamic conditions for reduction. To maintain these conditions, the rate of reduction/carburisation should be higher than the rate of solid carbon deposition. The paper discusses reduction of pure manganese and chromium oxides at relatively low temperatures, and constraints in reduction of manganese and chromium ores. Reduction of metal oxides by carbon in hydrogen as an alternative use of natural gas is also discussed.

Jan 1, 2014

By C. E. Lancelle, J. T. Volk, H. F. Wang, D. Fratta

"The Main Injector Neutrino Oscillation Search (MINOS) Near Detector Hall at Fermilab and the Lafarge – Conco Mine are located approximately 100 meters underground in the Galena-Platteville dolomite just below its contact with the overlying Maquoketa shale in Northeastern Illinois, USA. A new cavern was excavated adjacent to the MINOS Near Detector Hall at Fermilab to house the near detector for the Off-axis Neutrino Appearance Experiment (NOvA) program. During this excavation approximately 1150 cubic meters of shale rock were removed. Tiltmeter arrays consisting of a series of hydrostatic leveling sensors (HLS), which are spaced regularly over a total distance of 50-to-100 meters, were used to monitor subsurface deformations. The tiltmeter response in the MINOS Near Detector Hall due to the NOvA cavern excavation is approximately thirteen times the estimated response based on using laboratorydetermined properties. The discrepancy between modeled and measured tilt is likely due to differences in Young’s Modulus in the rock mass versus in a small laboratory sample. Amplitudes of measured solid earth tides differ from the amplitudes of theoretical solid earth tides by up to 40 percent for both arrays. This is likely due to a local heterogeneity or discontinuity.INTRODUCTIONLong baseline tiltmeters have been used to record small earth movements since the early 1900s. One of the first studies using long baseline tiltmeters to measure earth tides was published by Michelson (1914). He used a leveled 152-meter long, 0.15-meter diameter tube half-filled with water connecting two concrete-lined pits. The pipe was trenched 1.75 meters underground in Williams Bay, Wisconsin in a sandy-clay soil. Initially only an east-west line was used, though a north-south line was added after it was seen that viable results were obtained. Measurements were made by hand either hourly or once every two hours depending on the time of day. When compared to 0.7 times the calculated earth tides, the tiltmeter signal matched almost exactly. This excellent result began the use of long baseline tiltmeters to measure small earth movements."

Jan 1, 2015

By S. F. Reiter, W. R. Hibbard

A survey of the effect of heat treatment on the room temperature hardness of Fe-Mo alloys has been made. Constant strain rate tensile tests were performed between room temperature and 1800°F. These data were analyzed to determine the effect of temperature and composition on the strain hardening coefficient and strain rate sensitivity. Constant load creep-rupture tests were made on these alloys and the results related to composition and structure. A relation between the high temperature strength of the precipitation hardened alloys and the volume of precipitate has been observed. IN view of the extensive use of ferritic materials at elevated temperatures, it is surprising to note the limited amount of information relating the variables of plastic deformation, i.e., composition, structure, temperature, stress, strain, and strain rate. Hollomon and Lubahn' showed how the several variables of plastic flow might be treated analytically. No data were available on carbon-free iron and its alloys in a form suitable for this analysis. Several German investigations2-" constitute most of the experimental work relating high temperature properties to the constitution of these types of materials. In order to obtain new data, the iron-rich alloys of the Fe-Mo system were selected for detailed investigation for the following reasons: 1—Some of the important effects of molybdenum on the mechanical properties of iron have already been studied.' , 821 2—By suitable heat treatment of selected alloys, it is possible to study strengthening effects of four types: AT -a transformation, B—substitutional, C—precipitation, and D—dispersion of hard inter-metallic compound. Materials and Treatment Four-pound ingots were vacuum cast, employing the same melting schedule previously used.? The raw materials were electrolytic iron and lamp-grade molybdenum. The ingots were forged to l/z in. sq. rod and one portion swaged to 0.350 in. diam rod for the production of 1 15/16 in. long button-head specimens. The button-head specimen blanks were solution treated for 16 hr at 2100°F in hydrogen of —70°C dewpoint and then water quenched. They were subsequently plunge ground to the standard 0.160 in. diam test bar. Micrographs of the solution treated alloys are given in Figs. la through Id. The higher molybdenum alloys contained large equiaxed ferrite crystals similar to those in Fig. Id. A portion of the % in. rod was hot rolled to 0.100 in., sandblasted, and cold rolled to 0.020 in. Strip tensile specimens having a 0.020x0.200 in. cross-section and a 2.25 in. gage length were machined from the sheet. The alloys containing molybdenum were subsequently annealed 1 hr at 1560°F. The iron strip was annealed 4 hr at 1300°F in wet hydrogen. The resultant structures are shown in Fig. 2a through h. The ASTM grain sizes were 1 to 3 as solution heat treated or 3 to 4 as annealed. The chemical analyses of the alloys are given in Table I. Carbon contents were obtained after the heat treatments in hydrogen. Alloy 15.9 pct Mo was tested as a cast alloy.'

Jan 1, 1956

By A. W. Fahrenwald

[In studying coarse sand flotation3/ the question of the relation between fineness of grinding and mill capacity logically arose. Everyone familiar with present fine-grinding practice knows that the capacity of a ball mill or similar mill is determined, among other things, by the fineness of the finished product. Undoubtedly a great many mining companies must have a good deal of data directly bearing on this point, yet no quantitative relationship between ball-will capacity and fineness of finished product has been established. The experimental study presented here is an effort to establish this relationship in a semiquantitative way. The subject is a tremendously large one and grows in complexity as the study becomes more searching. In this work the power consumed by the mill in the various experiments was not determined end neither vas the steel consumption measured; mill capacity only was considered.]

Jan 1, 1930

By S. Shrestha

Magnesium-based alloys are of growing interest for many industrial applications due to their favourable strength-to-weight ratio and excellent castability. Mass reduction has advantages in many industrial sectors for example, in automotive, a reduction in mass improves fuel economy and can lead to more efficient mechanical systems by reducing the weight of moving parts like wheels, gears, pistons. However, the relatively poor corrosion and wear resistance limits the use of magnesium and its alloys in many potential applications. The patented Keronite® plasma electrolytic oxidation (PEO) process enables manufacturers to overcome such problems and, in its latest generation equipment has been developed to industrial realisation for high volume production. This paper presents microstructural characteristics and corrosion performance of two most widely used high pressure die-cast magnesium alloys AZ91D and AM6OB with a duplex corrosion protection coating system that comprised a thin Keronite pre-treatment followed by a subsequent automotive grade final powder coat.

Jan 1, 2006

By Appendix by A. S. Goldoni, R. E. Tate, E. M. Cramer

The diffision coefficient for self-diffision of plutonium in the temperature range 350" to 440°C has been measured by using puZ3 as the tracer isotope. Autoradiopaphic techniques were used to inzlestigate the possibility of grain boundary diffusion, hut only evidence for volume diffusion was found. The least-squares fit of the data gives the .following equation for the diffision coefficient: The computer least-squares technique for fitting the nonlinear equations is outlined. DETERMINATION of the self-diffusion coefficient of the fcc 6 phase of plutonium is in principle a straightforward experimental task. However, the chemical reactivity, the intense @ activity, and the toxicity of plutonium put limitations on the experimental techniques. The technique selected included roll bonding for preparation of the diffusion couples and pulse-height analysis of the @-particle activity to determine the distribution of the PU tracer in the diffusion couples. EXPERIMENTAL PROCEDURE Couple Preparation. Cylinders about 0.5 in. in diam were cast from two special stocks of plutonium, one of which had been enriched in puZ3', as shown in the isotopic analyses listed in Table I. For each roll-bonded composite sheet, a cylinder 0.437 in. in diam and 0.190 in. thick was turned from each kind of plutonium on a lathe in a 98 pct He atmosphere. The two freshly machined cylinders were positioned face to face in a tube of commercially pure aluminum which had been sealed at one end by welding and the assembly was evacuated on a vacuum manifold overnight. The elapsed time between machining the faces of the plutonium cylinders and evacuating the loaded tube was about 15 min. After overnight evacuation of the assembly the indicated vacuum was 1 X 10"5 torr or better. The aluminum tube was then warmed and pinched off with a cold-welding tool. The pinched-off weld was also fusion-welded as an additional precaution against leakage of air into the evacuated assembly. The assembly was immediately heated for 30 min in a 250°C furnace and reduced in thickness by being passed through a rolling mill with rolls heated to 200°C. The rolling schedule (four passes of 100 mils each with a 10-min reheat after two passes) reduced the thickness of the assembly to 100 mils. The rolled assembly was allowed to cool normally in air. The rolled assembly was sheared at the edges and the aluminum peeled from the composite plutonium sheet. The elliptical sheet was about 0.060 in. thick and usually three 0.383-in.-diam disks could be punched from its central portion. The sheet was heated on a hot plate to the ductile low 0 range (140°C as measured by temperature-indicating pellets) before each disk was quickly punched. The quality of the bond in the disks was evaluated by metallographic examination of the scrap sheet adjoining the hole left by the punch. Only well-bonded specimens without oxide in the interface (as indicated by metallography) were considered satisfactory for further use. More than half of the specimens so examined contained sufficient oxide in the interface to be rejected. Diffusion Anneal. Each disk to be diffusion-annealed was wrapped in 1-mil-thick tantalum foil and sealed within a Pyrex capsule evacuated to 1 x 10~5 torr or better. This capsule was then sealed within another Pyrex capsule at a similar pressure. The diffusion anneals were carried out at temperatures between 350" and 440°C in Marshall furnaces adjusted to have a temperature gradient of not more than *1/2"C over a 5-in. length. This gradient was then further smoothed by using a nickel tube as a liner in the furnace. The liner was divided into three longitudinal cavities by a septum of nickel sheet to which two calibrated Chromel-Alumel thermocouples were attached. One thermocouple was used for controlling the furnace temperature by means of a Brown Pyrovane controller equipped with a Capaciline anticipation circuit; the second thermocouple was monitored twice daily with a Leeds and Northrup K-2 precision potentiometer.

Jan 1, 1964

By Jennifer S. Riefenberg

The U.S. Bureau of Mines conducts basic and applied research related to predicting, eliminating, and/or controlling rock bursts in underground hard-rock mines and coal bumps in underground coal mines. An important element in this research is the development of a reliable and efficient microseismic source location technique. This report presents the results of a Bureau study to develop and evaluate a new algorithm to locate microseismic events based on the Simplex method, a powerful linear programming technique. The technique was tested on both field data and simulated data. Microseismic event source locations obtained with this new Simplex-based algorithm were shown to have less error than those locations obtained using a least squares method. It was concluded that the Simplex approach to source location of microseismic events can be used effectively in microseismic monitoring.

Jan 1, 1989

By Clarence Balke

SMALL buttons of fused tantalum have been produced by are fusion in a vacuum, by drawing an arc between sticks of pressed tantalum and a tantalum-faced water-cooled copper block. However, ingots of appreci-able size can be produced only by the heat-treatment of bars pressed from powder. The following outline covering the production of finished bars of tantalum by the methods of powder metallurgy is also used for the production of columbium, taking into account the difference in the melting points of these two metals. PRESSING THE POWDER With possibly a few exceptions, a pressing operation is one of the essential steps in the practice of powder metallurgy. In fact, the author's experience with a number of high-melting-point metals and with numer-ous types of hard carbide compositions has led him to believe that this operation is often one of the most important in the- entire process, and frequently one of the most difficult to carry out in a satisfactory manner. Defects clue to improper pressing can readily lead to a defective finished product. It is the author's opinion that rarely is a bar or other article pressed from metal powder in such a way that all parts of the piece are uniformly pressed. The nearest approach to uniformity of pressing is possibly attained when the powder is contained in a flexible receptacle, such as rubber, and is pressed under a liquid by hydrostatic pressure. However, this method is not generally applicable. Hydraulic pressing in steel dies where one or two punches are forced into the die must usually be resorted to. As the pressure in such a die is built up, the powder begins to cling to the walls of the die with a tenacity dependent upon the nature of the powder, and this results in a bridging action, so that the layers of powder adjacent to the moving punch are pressed more heavily than those further removed in the mass. Frequently, as the pressure is carried higher, there may be a mass slippage of the powder upon itself, with the result that slip cracks are formed within the pressed

Jan 1, 1938

By D. KEYS, D. E. Gemmell

The portion of the earth's surface covered by peatlands has been conservatively estimated at over 420 million ha (Kivinen and Pakarinen 1980). It is estimated that there are about 170 million ha of peatland in Canada. New Brunswick contains about 140,000 ha. Harvesting of peat for horticultural purposes has been carried out in New Brunsiwck since 1942. This industry, and the potential for using peat for energy purposes, indicated the need for an accurate assessment of the resource. In 1975, therefore, the New Brunswick Department of Natural Resources began a detailed peatland inventory. Assistance from the Canada Department of Regional Economic Expansion permitted acceleration of this program and field work was completed in 1982. Information gathered by the program will form the basis for a management plan for future use of the resource.

Jan 1, 1984

By Clarence W. Balke

Small buttons of fused tantalum have been produced by are fusion in a vacuum, by drawing an arc between sticks of pressed tantalum and a tantalum-faced water-cooled copper block. However, ingots of appreciable size can be produced only by the heat-treatment of bars pressed from powder. The following outline covering the production of finished bars of tantalum by the methods of powder metallurgy is also used for the production of columbium, taking into account the difference in the melting points of these two metals. Pressing the Powder With possibly a few exceptions, a pressing operation is one of the essential steps in the practice of powder metallurgy. In fact, the author's experience with a number of high-melting-point metals and with numerous types of hard carbide compositions has led him to believe that this operation is often one of the most important in the entire process, and frequently one of the most difficult to carry out in a satisfactory manner. Defects due to improper pressing can readily lead to a defective finished product. It is the author's opinion that rarely is a bar or other article pressed from metal powder in such a way that all parts of the piece are uniformly pressed. The nearest approach to uniformity of pressing is possibly attained when the powder is contained in a flexible receptacle, such as rubber, and is pressed under a liquid by hydrostatic pressure. However, this method is not generally applicable. Hydraulic pressing in steel dies where one or two punches are forced into the die must usually be resorted to. As the pressure in such a die is built up, the powder begins to cling to the walls of the die with a tenacity dependent upon the nature of the powder, and this results in a bridging action, so that the layers of powder adjacent to the moving punch are pressed more heavily than those further removed in the mass. Frequently, as the pressure is carried higher, there may be a mass slippage of the powder upon itself, with the result that slip cracks are formed within the pressed

Jan 1, 1938

By Clarence W. Balke

Small buttons of fused tantalum have been produced by are fusion in a vacuum, by drawing an arc between sticks of pressed tantalum and a tantalum-faced water-cooled copper block. However, ingots of appreciable size can be produced only by the heat-treatment of bars pressed from powder. The following outline covering the production of finished bars of tantalum by the methods of powder metallurgy is also used for the production of columbium, taking into account the difference in the melting points of these two metals. Pressing the Powder With possibly a few exceptions, a pressing operation is one of the essential steps in the practice of powder metallurgy. In fact, the author's experience with a number of high-melting-point metals and with numerous types of hard carbide compositions has led him to believe that this operation is often one of the most important in the entire process, and frequently one of the most difficult to carry out in a satisfactory manner. Defects due to improper pressing can readily lead to a defective finished product. It is the author's opinion that rarely is a bar or other article pressed from metal powder in such a way that all parts of the piece are uniformly pressed. The nearest approach to uniformity of pressing is possibly attained when the powder is contained in a flexible receptacle, such as rubber, and is pressed under a liquid by hydrostatic pressure. However, this method is not generally applicable. Hydraulic pressing in steel dies where one or two punches are forced into the die must usually be resorted to. As the pressure in such a die is built up, the powder begins to cling to the walls of the die with a tenacity dependent upon the nature of the powder, and this results in a bridging action, so that the layers of powder adjacent to the moving punch are pressed more heavily than those further removed in the mass. Frequently, as the pressure is carried higher, there may be a mass slippage of the powder upon itself, with the result that slip cracks are formed within the pressed

Jan 1, 1938

By H. L. Barwood

Luminescence excited by electron bombardment, or cathodoluminescence (CL), is a very useful tool in petrographic examination of rocks, minerals and ores. Differences in luminescence colors and intensities allow detection and delineation of mineral species and composition zones difficult to separate visually by normal polarized light microscopy. The cold cathode CL chamber at Indiana University is used with a binocular microscope that has interchangeable attachments for a normal film camera, a digital camera and a fiber optic spectrometer. This allows imaging of the specimens as well as limited spectrographic analysis of the emitted luminescence. The chamber on this CL unit is large enough to accommodate several thin sections, polished mounts, grain mounts or rock slices at one time. Luminescence petrographic techniques were used to study alkali syenites and carbonatites from the Arkansas. Alkali feldspars in the syenites reveal a history of growth, fenitization and replacement through color and intensity differences. Primary orthoclase luminesces bright blue and is often zoned with a duller blue overgrowth of microcline. Fenitization of the feldspars is demonstrated by dull to bright red luminescence and replacement veins of albite often have a bright yellow green luminescence. Late microcline and perthites from the syenite pegmatites have a dull yellow to orange luminescence. Easily visible on this background of feldspars are grains of apatite (yellow), fluorite (violet), zircon (greenish), sodalite (orange) and mosandrite (green). Complex pseudoleucite syenites from Magnet Cove, Arkansas show similar minerals but also include xenolithic quartz (violet), manganwollastonite (bright orange), benitoite (intense blue) and lorenzenite (green). Carbonatites from Arkansas contain a wide variety of calcite textures and intensities of luminescence. Grains of carbonatite in well cuttings are easily distinguished from sedimentary calcites by their complex “flame” luminescence and the frequent presence of euhedral apatite grains (yellow). Apatite crystals separated from the Arkansas River Valley carbonatites by acid digestion show complex zoning. The cores of these apatites are yellow luminescing due to CL activation by Mn enrichment while the rims are violet luminescing due to REE enrichment. Complex zonation between the cores and rims is easily visible using CL.

Jan 1, 2001

By L. F. Bishop

THE ore bodies of the Butte district1 are found in many different vein systems having many different structural characteristics; some are narrow with self-supporting ore but with weak walls; some are wide with weak or strong ore and weak walls; some of the veins dip steeply and others do not; some have well defined walls, and others, in the "horsetail" area, are mined to sample limits. Consequently, many types of stoping methods are used in mining these ores. The stoping methods used in the Anaconda Copper Mining Company's properties are the square-set and cut-and-fill. The square-set method is the principal stoping method used because, generally speaking, the ore and walls are weak, the ore is high grade, and good extraction is required. These square-set stopes may be classified as conventional, vertical slice, slot, timber rill, and Mitchell slice types. The conventional type square-sets are those of various shapes and sizes, mined by horizontal slicing to the boundaries of the stopes. The rock is slid to the chute and the filling is moved by gravity. The ore and waste may be handled with a scraper when local conditions require it. The vertical-slice square-set system is the type used in narrow veins that are mined in vertical panels. The slot stopes are stopes in wide veins that employ a slot across the vein instead of a con- ventional chute to handle the ore. The timber rill fs a type of square set in which the ore is mined as in inclined cut and fill but the square-set timber is used. The Mitchell slice is the type used for some broken or heavy ore blocks, or for pillar extraction between two converging slot stopes. The cut-and-fill method is used where the ore will stand without much support although the walls may be weak. The principal type of this method is the horizontal cut-and-fill, with mechanical scraping. The inclined cut-and-fill, or rill, stopes are used in some veins too narrow for scraping. The production from the various meth: ods in use for the second six months of 1944 are shown in Table I. [ ] This paper deals mainly with the vertical slice and slot types of square-set stoping, because of their effect on production locally and their potential possibilities here and in other districts, with sufficient reference to conventional square-setting for comparison.

Jan 1, 1945

By R. Parada

A real-time dynamic simulation model has been developed to characterise the flash furnace operation at the Chagres smelter. This model permits the operators to plan the process to meet the Peirce Smith converters' schedules and feed the acid plant with gases that satisfy its best operating efficiency range. Essential control parameters for the furnace (process air enrichment, oxygen coefficient and supplementary heat) are calculated to satisfy process targets such as matte grade, slag silica and matte/slag temperatures. These calculations are carried out with a real-time simulation. Flash furnace control and operational stability permits setting up control strategies that streamline the flow of copper to converters and of sulphur to the acid plant.

Jan 1, 1999

By J. Eriksson

Slag from stainless steelmaking is known to disintegrate, which is an environmental problem and prevents the cooled slag from being utilized. This disintegration is due to the transformation from the ßto the ? polymorph of di-calcium silicate. The transformation is accompanied by an increase in volume of about 11% and a total disintegration of the slag. AOD slag from stainless steelmaking was re-melted in a laboratory induction furnace, together with olivine and calcinated dolomite, to investigate the prevention of disintegration by increased MgO content of the slag with small changes in CaO to SiO2ratio. The modified slag was examined with X-ray diffraction and scanning electron microscopy. The trials showed that an increased MgO content can change the mineral composition towards formation of more Merwinite and Bredigite, which prevents disintegration of the slag. Keywords: slag, disintegration, di-calcium silicate

Jan 1, 2004

By H. J. Ramey

As fluids move through a wellbore, there is transfer of heat between fluids and the earth due to the diflerence between fluid and geothermal temperatures. This type of heat transmission is involved in drilling and in all producing operations. In certain cases, quantitative knowledge of wellbore heat transmission is very important. This paper presents an approximate solution to the wellbore heat-transmission problem involved in injection of hot or cold fluids. The solution permits estimation of the temperature of fluids, tubing and casing as a function of depth and time. The result is expressed in simple algebraic form suitable for slide-rule calculation. The solution assumes that heat transfer in the wellbore is steady-state, while heat transfer to the earth will be unsteady radial conduction. Allowance is made for heat resistances in the wellbore. The method used may be applied to derivation of other heat problems such as flow through multiple strings in a wellbore. Comparisons of computed and field results are presented to establish the usefulness of the solution. INTRODUCTION During the past few years, considerable interest has been generated in hot-fluid-injection oil-recovery methods. These methods depend upon application of heat to a reservoir by means of a heat-transfer medium heated at the surface. Clearly, heat losses between the surface and the injection interval could be extremely important to this process. Not quite so obvious is the fact that every injection and production operation is accompanied by transmission of heal between wellbore fluids and the earth. Previously, the interpretation of temperature logs',' has been the main purpose of wellbore heat studies. The only papers dealing specifically with long-time injection operations are those of Moss and White3 and Lesem, et al.' The purpose of the present study is to investigate wellbore heat transmission to provide engineering methods useful in both production and injection operations, and basic techniques useful in all wellbore heat-transmission problems. The approach is similar to that of Moss and White:' DEVELOPMENT The transient heat-transmission problem under consideration is as follows. Let us consider the injection of a fluid down the tubing in a well which is cased to the top of the injection interval. Assuming fluid is injected at known rates and surface temperatures, determine the temperature of the injected fluid as a function of depth anti time. Consideration of the heat transferred from the injected fluid to the formation leads to the following equations. For liquid, Eqs. 1, 1A and 2 are developed in the Appendix. These equations were developed under the assumption that physical and thermal properties of the earth and wellbore fluids do not vary with temperature, that heat will transfer radially in the earth and that heat transmission in the wellbore is rapid compared to heat flow in the formation and. thus, can be represented by steady-state solutions. Special cases of this development have been presented by Nowakl and Moss and White.3 Both references are recommended for excellent background material. Nowak' presents very useful information concerning the effect of a shut-in period on subsequent temperatures. Since one purpose of this paper is to present methods which may be used to derive approximate solutions for heat-transmission problems associated to those specifically considered here, a brief discussion of associated heat problems is also presented in the Appendix. Analysis of the derivation presented in the Appendix will indicate that many terms can be re-defined to modify the solution for application to other problems. Before Eqs. 1, 1A and 2 can be used, it is necessary to consider the significance of the over-all heat-transfer coefficient U and the time function f(t). Thorough discussions of the concept of the over-all heat-transfer coefficient may be found in many references on heat transmission. See McAdams5 or Jakob," for example. Briefly, the over-all coefficient U considers the net- resistance to heat flow offered by fluid inside the tubing, the tubing wall, fluids or solids in the annulus, and the casing wall. The effect of radiant heat transfer from the tubing to the casing and resistance to heat flow caused by scale or wax on the tubing or casing may also be included in the over-all coefficient. According to McAdams, on page 136 of Ref. 5>

By E Selvapandian, R Barr

Arrium (previously OneSteel) initiated a desktop study into the performance of its hematite ore beneficiation plant in early 2010. The beneficiation plant utilises jig concentrators and spirals to upgrade low-grade hematite recovered during mining at the Iron Duke (ID) mine site located 60 km south-west of Whyalla. The study, conducted in conjunction with Mineral Technologies, identified a number of opportunities for improvement, which were validated by a series of sampling campaigns and a pilot plant trial. One of the major recommendations was to upgrade the ultra-fines processing circuit from a single-stage spiral circuit to a three-stage circuit. The upgrade of the ultra-fines circuit was estimated to provide a significant increase in fines production and grade.In order to capitalise on the strong iron price at the time of the project, Arrium decided to utilise a fast-tracked approach to design, construct and commission the processing equipment required to achieve the improvements identified. This decision introduced the risk of missing critical steps in the project development process, which could have potentially resulted in major issues in latter stages of the project. In addition to the challenges introduced due to the expedited time line for project completion, this project presented unique challenges due to its brownfield nature. One such challenge faced was the integration of the new equipment and control system software.Furthermore, the importance of the ID ore beneficiation plant (OBP) contribution to the companyÆs export commitments meant the upgrade work had to occur while minimising disruption to normal operation. This decision presented a set of new challenges to an already complex project. One such challenge was the need to build and commission the new spiral circuit in isolation from the operating plant.The aim of this paper will be to highlight some of the challenges faced in a complex brownfield project such as the ID OBP upgrade and discuss how they were managed to enable the successful commissioning of the process in early 2012.CITATION:Selvapandian E and Barr, R, 2013. Managing challenges faced in the brownfield commissioning of an ultra-fine hematite processing circuit at ArriumÆs Iron Duke ore beneficiation plant, in Proceedings Iron Ore 2013 , pp 533-538 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

To identify the most successful methods now in use for controlling respirable dust in longwall mines using double-drum shearers. Approach Conduct dust surveys at six longwall mining sections that use double-drum shearers and are regularly in compliance with the Federal Respirable Dust Standard, to identify effective dust control techniques. The selection of mine sites was based on recommendations provided by the Mine Safety and Health Administration. Instantaneous and short-term gravimetric instrumentation make it possible to isolate longwall dust sources and to determine the effectiveness of dust control techniques. (These procedures were developed by the Bureau of Mines, and are described in detail in Technology News Bulletins 134 and 135.) Production levels, and seam heights at each of the six longwall sections were: 53", 700 tps; 60", 800 tps; 72", 1000 tps; 79", 1500 tps; 84", 2000 tps; 96", 1500 tps. Survey Results Three effective dust control techniques were identified. 1. Shearer Operators on Intake Side of Lead Drum-At all mines surveyed, an important factor in controlling dust exposures at the shearer is the use of a cut ting sequence that allows the shearer operators to work most of the time on the intake air side of the lead drum. Dust profiles, like those plotted from data at two mines (see the graphs), show the large gradient in dust concentrations that can

Jan 1, 1982

By Jiakai Zhang

Many postconsumer electrical and electronic equipment wastes contain a considerable amount of rare earth elements (REEs); however, the current level of REE recycling from them is limited (<1%). Neodymium–iron–boron (NdFeB) magnets, used at both small- and large-scale, from computer hard disk drives and small tools to wind turbines and cars, are a good example of such waste materials that contain high content of neodymium (Nd) and dysprosium (Dy). These elements are considered critical metals because they are the main building block of emerging green technologies that will allow for GHG emission reductions. Because demand for these green products is increasing around the world, the demand for REEs is increasing quickly, putting their supply at risk in the near future. Thus, it is critical to develop efficient, robust, and cost-effective processes to recycle these elements from this class of electronic waste materials. Here, we performed a thorough characterization of a N52–NdFeB magnet to identify its composition, crystal structure, and morphology. Furthermore, we developed an efficient hydrometallurgical process to extract Nd and Dy with high efficiency (more than 95%).

By Franz Ramstorfer

No lingotamento contínuo de placas, rompimentos de veio pelo colamento e problemas de qualidade de superfície, como trincas longitudinais, são frequentemente relacionadas à lubrificação insuficiente no molde de lingotamento contínuo devido ao pó fluxante ou a prática de oscilação inadequados. Para detectar, com vistas a prevenir, este tipo de problema de processo, um método para avaliar em tempo real o coeficiente de atrito entre o veio e as placas do molde foi desenvolvido, utilizando-se a medição da força que atua nas placas laterais do molde e as forças de oscilação. Observou-se que o coeficiente de atrito do molde é um parâmetro confiável para auxiliar no desenvolvimento de pó fluxante, na otimização de parâmetros de oscilação e no monitoramento online do desempenho de pó fluxante.

Aug 16, 2017