Search Documents

By W. C. Clarke

An empirical study of the nature of the embrittle-ment which occurs in martensitic and semiaustenitic precipitation hardening stainless steels upon exposure at temperatures of from about 550" to 875°F has been undertaken. This work was aimed at determining cazusation and means of controlling this phenomenon. A commercial copper bearing precipitation hardening alloy was used as a basic material for study. The effect of heat treatment variables was studied as was the effect of variations in analysis. It is concluded from the evidence that martensitic and semiaustenitic precipitation hardening stainless steels are subject to 885°F ernbrittlement similar to that observed in the straight chromium stainless steels. A characteristic of precipitation hardening stainless steels which has limited their use in certain applications is that they embrittle when held at temperatures in the range of from about 550" to 900°F. This is true to a more or less degree in all currently available alloys, either the basically martensitic type or the semiaustenitic type. The rate of embrittlement varies markedly with exposure temperature, being low at 550" to 600°F and in-creasing as the temperature increases. In spite of this embrittlement, these alloys with their unique combination of high mechanical strength, reasonable toughness, and good corrosion resistance are used in many hundreds of applications. Nevertheless, there are potential applications where the embrittle-ment described is a limiting factor. The purpose of this investigation was to study the embrittlement of these alloys and to find a way to control or eliminate it. GUIDELINES USED IN PRESENT WORK The work reported in this paper is based on a study of 17-4 PH*, a very widely used alloy. It has been used *Trademark of Armco Steel Corp., licensor. in pressurized water and boiling water atomic reactors operating at about 550°F for a number of years. As the life of such equipment is extended or operating temperatures are raised, the possibility of embrit-tlement becomes of increasing concern to materials engineers. Much investigation work was done with respect to the use of 17-4 PH at 550°F. K. C. Antony' states "Such estimation" (of an activation energy for the diffusion of chromium in iron) "would indicate W. C. CLARKE, Jr. is Senior Research Engineer, Advanced Materials Division, Armco Steel Corp., Baltimore. Md. This manuscript is based on a talk presented at the symposium on New Developments in Stainless Steel, sponsored by the IMD Corrosion Resistant Metals Committee, Detroit, Mich., October 14-15, 1968. significant secondary aging is improbable at temperatures less than 700°F within normal component service life". This statement is modified however by the recognition of the accelerating tendencies of applied stress and internal stress as well as the possible effect of irradiation. In this investigation of 17-4 PH, the H 1100 (1900°F-1 hr oil quench or air cool + 1100°F-4 hr-air cool) condition was used, partly because this condition is normally used in atomic reactors. As shown later, the precipitation hardening temperature has no real bearing on the rate of embrittlement. An exposure temperature of 800°F was selected since embrittlement at 800°F is rapid, permitting development of relative data in time periods of 400 to 500 hr. For those not familiar, a nominal present day analysis of 17-4 PH is: C Mn P S SiCrNiCuCbN 0.04 0.30 0.015 0.015 0.60 16.00 4.30 3.25 0.23 0.030 TYPICAL BEHAVIOR OF 17-4 PH Figs. 1 and 2 show the behavior of a commercial heat of 17-4 PH under the conditions defined. Characteristically, 800°F exposure causes a rapid drop in Charpy V-notch impact strength. Tensile and yield strengths gradually increase and a gradual loss of elongation and reduction of area occur, accompanied by an increase in hardness. Notched tensile strength increases to 125 hr exposure and then sharply decreases after exposure for 500 hr. The notched vs un-notched tensile ratio remains virtually constant to exposure for 125 hr (1.67 to 1.56) but drops to 1.15 after 500 hr. Tensile ductility is not alarmingly affected even after much longer exposure times than these. For example, samples aged at 1100°F for 1 hr exposed at 800°F for 4000 hr showed a drop in elonga-tion of from 13 to 11 pct and in reduction of area of from 58 to 37 pct. Notched impact is the property SmIgth KSI 3JJ[/__________^UTS-Nrteh 260 ;/- 240 —^ 200 UTS-Smooth________._, o ioo mo Sob" m Too Hours Exposure Fig. 1—Effect of exposure at 800°F for various times on notched tensile strength and smooth tensile and 0.2 pct yield strength of 17-4 PH in the H 1100 condition.

Jan 1, 1970

By Sean Hillacre, Arthur Lieu

NexGen’s approach to uranium processing design including the crushing/grinding and leaching of raw ore through to yellowcake precipitation and tailings management focuses on minimizing surface footprint, freshwater consumption, and human radiation exposure. Applying the concept of best available technologies economically achievable (“BATEA”), NexGen continues to research, evaluate, test and validate various advanced technologies that can be incorporated into the Project design, including distinctive tailings storage techniques. Additionally, NexGen is proposing that tailings generated from the mill processes be used as cemented paste backfill of stopes, as well as stored in a purpose-built, Underground Tailings Management Facility (“UGTMF”) comprised of several dedicated chambers. The paste backfill method of tailings storage is used globally, however, constructing purpose-built tailings chambers in waste rock is a new concept in uranium mining, which would typically be cost prohibitive for most projects given the expense to develop non-economic material for the sole purpose of storing tailings. The Rook I Project is uniquely positioned to implement the UGTMF due to robust Project economics and favourable technical setting which provides NexGen with the opportunity to set an elite standard for tailings management. When compared to conventional surface tailings management facilities, storing tailings underground as cemented paste reduces geotechnical, geochemical, environmental, and human health risks associated with tailings management. Additionally, the UGTMF vastly reduces the area of surface disturbance and allows for progressive decommissioning during the life of mine operations.

Jan 1, 2020

By John G. Ayttes

"The following is a review of the advance of raise boring and its current position. The viewpoint presented is that the mining industry, through its worldwide acceptance of raise boring, has acknowledged the success of the method in general. Acceptance, however, does not imply complete satisfaction with either the equipment or current operating costs. Therefore, a brief review of how boring costs are being r educed is presented, citing examples. Recent raise borer applications of special interest are presented to show adaptability of current equipment, and some special projects in the planning stage are highlighted."

Jan 1, 1972

By S. G. Sawyer

The Pittsburgh Safety and Health Technology Center (PSHTC) of the Mine Safety and Health Administration (MSHA) provides engineering and scientific support to the inspectorate personnel of MSHA. One of the Center's myriad roles is to assist in the investigation of mining accidents, especially those involving fatalities. Center personnel utilize forensics to help uncover the causes of accidents and to make technical recommendations on the prevention of future similar mishaps. To exemplify a typical forensic investigation, this paper documents the methodology used in determining the reasons for a boat sinking, which resulted in a double fatality on a mine company pond.

Jan 1, 1997

By Juan Mori Arellano

El presente texto describe la evolución de la tecnología con sus limitaciones iniciales en su aplicación, el cambio cultural de una empresa en cuanto a sus necesidades de conocimientos, la globalización de los mercados y el alto nivel competitivo que ha permitido adoptar diferentes esquemas de mantenimiento con el fin de aumentar la eficiencia en equipos de carguío superficial.

Mar 1, 2017

By David C. Oyler

The U.S. Bureau of Mines studied the interaction of longwall shield supports and adjacent strata at the Meigs No. 31 Mine in southeastern Ohio. Twenty-three legs of twenty shields at midface were instrumented with pressure transducers and monitored for 11 weeks. During the project, leg setting pressures were reduced twice to determine the effect of setting pressure on shield-strata interaction. No correlation was observed between setting pressure and leg loading rates. The shield loading profiles were consistent with a model in which the roof consists of two zones, a thin immediate roof loading the shields well below the typical setting force and a main roof zone essentially supported by the coal and gob and loading shields through its convergence. This model was used to develop an equation for estimating average loading rates at the site. The only variable of the equation is time, and the equation consists of an exponential term to account for the immediate roof loading and a linear term to account for main roof loading. The equation gave good correlation with average loading rates, but the variation in loading from cycle to cycle was too great for the equation to give good predictions of individual cycle loading rates.

Jan 1, 2010

By Singleton T

Increasing world competition puts pressure on sales volumes and prices. This in turn reduces potential profit margins. This in turn increases the focus on costs.Increasing demands on quality and service puts pressure on delivery performance - the right product at the right time. This in turn reduces the scope for errors and delays - and this in turn increases focus on equipment reliability. In the mining industry, both costs and equipment reliability have one significant thing in common - they are driven substantially by maintenance.

Jan 1, 1998

Blasts should be designed so as to maximise the percentage of charges which shoot to a free face (Le, to a pronounced rock/air interface).Free faces should be rough, parallel and reasonably near to blastholes and, very importantly, concavely·biplanar relative to the charges (see Fig. 6b). The presence of biplanar free faces requires that each charge fragments and detaches its quota of the burden rock before the detonation of:1. later-firing adjacent charges in single-row blasts, and2. dependent charges in multi-row blasts.In multi-row blasts, biplanar faces are best achieved:1. by drilling blastholes on equilateral triangular grids,2. by selecting a VI, V2 or V3 initiation sequence, and3. by using down-the-hole delays.Biplanar faces start to be created only when the conventional value of effective blasthole spacing/effective burden distance (Se/Be) increases beyond about 2.4. Values of Se/Be less than about 2.4 result in planar free faces. Where biplanar faces are created, conventional values of Se/Be are invalid and appreciably greater than real values of Se/Be.

Jan 1, 1986

By A. V. Kuznetsov, R. I. Kamkin, V. M. Paretskiy, A. Y. Mamaev, V. P. Bystrov, A. S. Vernigora

"Vanukov furnace technology is an efficient, proven pyrometallurgical injection technology, used extensively in Russia and Kazakhstan for a number of different applications. The technology was most widely adopted for processing copper sulfide concentrates for matte in smelters in Norilsk, Revda (Russia) and Balkhash (Kazakhstan). The following applications also were developed and tested at industrial scale: treatment of sulfide lead and lead-zinc concentrates, laterite nickel ore, production of cast iron, treatment of antimony gold-containing ores, and municipal solid waste. In this paper, current experience of Vanukov furnace application to these technologies is described with a number of general development trends and new areas of application.IntroductionAt the present time, the Vanukov process, developed at the Moscow State Institute of Steel and Alloys at the Department of metallurgy of non-ferrous, rare and noble metals with collaboration with other research organizations, is a highly efficient technological solution for processing different kinds of raw materials. The process was invented by Professor Andrey Vladimirovich Vanukov, whose research work began in 1949. From 1956 to 1975 test runs of the technology were carried out at the smelters in Norilsk and Balkhash. In 1976 a pilot Vanukov furnace was built in Ryazan. Furnace designs was modified to suit the various test programs. A major objective of each experiment was the determination of optimal working conditions for processing different types of raw materials such as copper, copper-nickel, copper-zinc, lead or pyrite concentrates, and materials containing secondary lead and zinc. After the death of Andrey Vladimirovich Vanukov in 1986, this technology and furnaces based on the technology were named after him: “Vanukov process” and “Vanukov furnace”. Today, the following furnaces based on Vanukov technology are either working or were tested at semi-industrial scale: three in Norilsk, two in Revda (Russia) and two in Balkhash (Kazakhstan) for treatment of copper sulfide concentrates for matte, one in Orsk (Russia) for processing laterite nickel ore, one in the Buruktal plant (Russia) for antimony gold-containing ores for antimony oxide sublimates and gold-containing metallic antimony, and one in China for processing sulfide lead and lead-zinc concentrates for production of black lead and zinc-containing sublimates."

Jan 1, 2011

By P. Taskinen, D. Lindberg, H. Viitala

The formation of copper chlorides in flue dust or deposits in heat recovery boiler of copper smelters or waste-fired boilers may lead to formation of corrosive partially molten deposits on walls and heat exchangers of the boilers. These deposits can contain various other metals, such as alkalis, Fe, Zn, Pb together with oxides and sulfates. In the present study, a thermodynamic model for copper-containing binary and ternary metal chloride systems within multicomponent CuCl-CuCl2-FeCl2-FeCl3- PbCl2-ZnCl2 system has been assessed and optimized based on own experimental phase equilibrium data, as well as literature data. The thermodynamic properties of the liquid phase was modelled using the quasichemical quadruplet model and a thermodynamic database was optimized to predict all available experimental data within the experimental error limits. The thermodynamic database allows for more accurate predictions of potential corrosion-related issues in various heat recovery boilers and waste-fired boilers due to formation of copper chlorides. INTRODUCTION In the copper flash smelting, flue dust can cause severe problems in the gas train, used for separating dust from the SO2-rich off gas, by forming corroding accretions on the walls of the heat recovery boiler. Formation of dust build-ups in the boiler need to be cleaned regularly and potential corrosion damage checked, requiring costly and unscheduled shutdowns of the flash smelting process. Compounds of copper and zinc among other elements having high vapour pressures may volatilize during the smelting of the copper concentrate, forming dust when the process gas cools down. Also, particles of solid or liquid iron oxides originating from the ore get transported with process gas to the heat recovery boiler as a result of entrainment in the flue gas (Miettinen, 2008) The dust deposit build-ups on the boiler walls are formed partly by direct impact of particles and partly by vapour condensation on the boiler walls. The initial deposition takes place by the condensation of vapours that contain zinc, lead, arsenic and other metals having high vapour pressures. Also, low melting point eutectic components of alkali salts such as chlorides and sulphates can act as sticky cohesive particles attaching to the boiler walls. The fine particles landing on the surface of the porous dust deposit layer react in the SO2-rich atmosphere of the boiler to sulphates. The process gas within the boiler contains SO2, O2, SO3, H2O and N2 that diffuse into the porous accretions to form a stagnant gas layer within the dust deposit structure. The composition of this gas layer may differ greatly from the composition of the process gas that is flowing on the surface of the accretion layer. Locally HCl and H2SO4 are formed and even a reducing atmosphere may exist within the dust deposit layer, allowing new reactions to take place. The local micro-atmosphere may enable metal sulphates to be reduced to secondary sulphides and even metallic components. Within the accretion layer, components may be formed that would not be stable in the gas atmosphere inside the boiler (Miettinen, 2008). This may be the mechanism by which for instance chlorides of Cu, Fe and Zn are formed within the deposit layer.

Jan 1, 2019

By W. G. Brissenden

"ALTHOUGH I SHOULD FIRST REVIEW the state of the mining art as it is today, because of the shortness of time I will confine myself to a re-view of the more important advances in that art which have been made in the past two to three decades. Then, a look at the opportunities and the challenges which now present themselves will be more meaningfulFirst, some of the more impor-tant developments in underground mining:(1) The recognition that good ventilation, visibility and working conditions are essential preliminaries to efficient production has resulted in their incorporation as a matter of practice in modern mine planning. (2) The introduction of the car-bide bit and the re-introduction of the airleg drill, and the resulting sharp rise in productivity, were early postwar developments. (3) The recovery of the coarser fraction of mill tailings for use as mine backfill also is an important cost-reducing development of recent years -and this has led to cemented backfill, which, al-though more expensive, meets certain specific needs and has tremendous potential. (4) Great strides have been made in improving explosives' materials and explosives' accessories. Millisecond-delay electric blasting caps, which improve fragmentation and reduce the seismic effect of blasting, and the development and •application for underground use of explosives are but two among many such improvements. (5) Trackless mining methods, using quarry-type equipment in some instances and specially de-signed low-headroom trucks, loaders and carrier-mounted drills in others have been successfully applied. (6) Dual-purpose load-haul units are now in use loading and hauling from open stope drawpoints, and smaller versions of this type of unit are in use in cut-and-fill and other types of stopes."

Jan 1, 1968

By R. M. Reynolds

Engitec Impianti, S?.p.A. of Milan, Italy has successfully designed, constructed and has in operation state-of-the-art battery breaker systems at two European locations. A third facility i:s partially completed in Toronto, Ontario, Canada. The CX system crushes whole batteries, separates the various components and desulfurizes the battery paste. The system also produces sodium sulfate from the sulfuric acid and lead sulfate contained in the batteries. Actual plant operating data indicates that the desulfurized paste contains less than 0. 6 percent sulfur and less than 0. 5 percent antimony. The CX system utilizes mechanical screening and an up-flow hydrodynamic separator to accomplish the component separation. Sodiwn hydroxide or sodium carbonate is used for desulfurization. The sodium sulfate brine is evaporated and crystallized to produce clean anhydrous sodium sulfate suitable for use by detergent or glass manufacturers. Plant data also indicates that an increase in furnace productivity of about 25 to 30 percent is achieved using feed from the CX system. The desulfurized paste is very suitable for electrolytic processing as an alternative to pyrometallurqical processing.

Jan 1, 1990

By G. Heymann, T. Grobler

Many tailings storage facilities in the Rustenburg region of South Africa’s North-West Province are founded on reworked residual norite derived from the weathering of the Bushveld Igneous Complex. With the implementation of the Global Industry Standard on Tailings Management, increased emphasis is placed on robust material characterisation, but laboratory testing is challenging. The results of Oedometer and undrained triaxial shear testing support a nonlinear failure envelope for effective stresses below the yield stress, transitioning to linear behaviour at higher stresses.

Apr 8, 2026

By M Bezzina

In 1995 Standards Australia International Limited æSAIÆ published a risk management standard titled AS/NZS 4360 Risk Management. It was the first such standard published by a recognised formal standards body anywhere in the world and it put Australia at the leading edge of the risk management discipline. Many Australian and international organisations have utilised the risk management standard and it is one of SAIÆs most important and popular standards. Since its publication in 1995, the risk management standard has gone through a major revision in 1999 and is currently undergoing another such review, which is due for completion in 2004. This paper will chart the application of the standard within certain key organisations since its inception in 1995. A brief overview of the methodology behind AS/NZS 4360 will be presented as well as an overview of supporting and related standards. It is prudent to base risk management and other management system issues on existing and tested standards rather than creating new proprietary approaches. Examples of areas in which the risk management standard might be applied in the mining industry are given, subject to the specific operations of each company: technical, commercial, environmental, informational, and safety and regulatory.

Jan 1, 2003

By Ivar Eskerud Smith, Ole Jørgen Nydal, Niranjan Reddy Challabotla, Svein Sævik

INTRODUCTION Airlift pumping, utilize compressed air that is injected at the bottom of a vertical pipe submerged in the water, reduces the mixture density inside the pipe and lifts the liquid or mixture of liquid and solids. This type of pumping technology, which is simple and without moving parts submerged in water, which provides several advantages compared to the mechanical pumping. Airlift is used in various difficult pumping applications such as transport of fluids corrosive to metals, explosives, nuclear and toxic materials in chemical industries, diamond mining and coal transport. Application of airlift to deep sea mining conditions was investigated by extensive laboratory experiments [1], theoretical analysis [2], and limited proof of concept field studies [3] starting in 1970’s with the discovery of huge amounts of manganese nodules discovered on the seabed at a depth of ranging from 4000 to 6000 m . Even after extensive investigations over the last five decades, there exists no commercial application of airlift technology for lifting of minerals. The major problems with the application airlift for deep ocean mining was (a) lack of control over the expansion of the injected gas, which increases the velocity in upper part of the riser pipe (b) lower efficiency compared to mechanical pumping [3]. Different flow regimes are encountered in airlift pumping: bubble, slug, churn and annular flow. Annular flow regime is the least efficient in lifting of particles and churn flow has better efficiency [3].

Jan 1, 2018

By D. DeGagne, E. De Souza, J. F. Archibald

This paper describes the potential use of anew agent material for backfill consolidation, ground waste glass, to be used as partial replacement of Portland cement fractions within backfill. Significant fractions of commercial and residential silica glass production is currently utilized as waste landfill and must be disposed of at high cost and with no foreseeable environ-mental benefit. This paper also demonstrates that waste glass materials could be effectively recycled as backfill additives, and that a significant, large and stable source of additive supply, currently land filled, can be developed. This new application will generate added value for such materials, serve to promote positive environ-mental stewardship and satisfy engineering sup-port requirements in mines.

Jan 1, 1997

By K. S. Krishnam, A. G. Guy

VOLUME 6 of the Transactions of the Baikov Institute of Metallurgy, Moscow, is devoted to the subject of "the experimental and theoretical study of the physical characteristics of dilute solid solutions,11 and summarizes work that has been done largely in the years 1958-9. In view of the attention that Soviet investigators have given to this subject, it seemed useful to carry out an independent experimental investigation in an effort to judge the scientific basis and practical significance of this field of study. The present note is a preliminary report of this investigation. The first property studied by the Soviet group was X-ray spectra of solid-solution alloys.' An anomaly observed at low concentrations (--0.05 at. pct) of the alloying element led to the theory that each impurity atom in a transition-metal base alloy is the center of a "block" of affected atoms with a radius of about 10"7 cm. This theory was further developed in a later paper.2 By this time similar anomalies had been found in diffusion coefficients3 and in thermal expansion.4 The entire development up to 1959 was reviewed in a comprehensive paper, and further theoretical ideas were also published at this time. Finally, the volume mentioned above was published in 19607 giving new experimental data on anomalies in optical properties and Hall constant, and a new theoretical treatment also appeared.' Although western scientists have done both theoretical work, summarized recently by Friedel,9 and considerable experimental work on dilute solid solutions, there is little support for the marked anomalies reported in the Soviet papers. Of the physical properties studied by the Soviet investigators, thermal expansion was chosen for the present investigation because of the relative ease of obtaining the necessary precision of measurement. A Leitz dilatometer was used for this purpose, and a special technique involving interchanging of the two specimens being compared permitted a precision of 0.05 x X in average thermal expansion over the range 27° to 600°C. The specimens were heated and cooled in vacuum or in a protective atmosphere at a rate of 50 °C per hr. Ferrovac E iron was used as the comparison specimen and in every case had a coefficient of expansion higher than (or equal to) that of the alloy. Since unintentional impurities are an important factor in studies of dilute alloys, special attention was given to the purity of the iron and the alloys used. The alloys were the same of those used by Abrahamson10 and by Michalak," and their preparation is described in these references. Chemical analyses of the Ferrovac E iron and of typical Fe-W and Fe-Mo alloys are given in Table I. The purity of the iron and alloys is undoubtedly higher than in the

Jan 1, 1962

By J. van der Merwe, C. Phetolo, V. Matjeke

The mechanical properties and microstructure of AlSi10Mg alloy samples that were printed by selective laser melting (SLM) were studied to determine the effect of processing parameters and building orientation. After printing, the alloy was stress relieved at 250°C for 2 hours. The microstructures were analysed by optical microscopy and scanning electron microscopy (SEM) to determine the alloy phases and distribution. Phase transformation characteristics of the material were evaluated using differential scanning calorimetry (DSC). Mechanical properties were determined by subjecting the XY- and Z-built samples to tensile and nano-indentation testing. The samples from the tensile tests were then used to perform fractographic analysis by SEM. The microstructural properties in each orientation revealed a non-homogeneous microstructure which was characterized by a semi-elliptical tract and fine silicon precipitates, which were found to be softer along the fusion zone. The DSC thermograms revealed that the material underwent two phase transformations during the first heating cycle. The mechanical properties revealed a higher UTS, higher yield strength, and a lower percentage elongation in the Z orientation than in the XY orientation. Fractographic analysis showed that crack initiation in both orientations started from the surface in a brittle manner due to surface flows, and then propagated via microvoid coalescence.

Jul 1, 2021

By Robin Schott

The blast furnace process is the most important process to produce pig iron. The necessary process energy is mainly covered by coke. But the production of coke is connected with CO2-emissions and high costs. A significant measure to reduce the coke rate and with it the CO2-emissions plus costs is pulverized coal injection (PCI) through the tuyeres into the blast furnace. A further increase to substitute coke by coal can be achieved by using the Oxycoal+ technology. This article compares and shows the cost effectiveness and the decrease of CO2-emissions with the help of simplified energy balances for the only coke operation of the blast furnace, the operation using pulverized coal injection and the operation using the Oxycoal+ technology.

Aug 17, 2017

By Sastry Putcha, Santosh Mummaneni, Swamy Avasarala, Vamshi Vemula

"This paper presents the results from a case study on the comparison of two strain acquisition instrumentation technologies, Geokon rebar strainmeters and Embedded Data Collectors (EDC) for the DC Water Main Pump Station project, in Washington D.C. These two instrumentation systems were installed by AVER in a single 18-inch (0.45 m) diameter augercast pile (with one-1.25 inch (3.175 cm) dywidag bar) at critical locations to determine the load transfer mechanism and establish a comparison between strain/load measured with these two systems along the pile. A quick static load test was performed on the test pile as per ASTM D1143 standard.Prior to the installation of the pile, a 24-inch (0.6 m) diameter outer casing was installed to the proposed cutoff elevation of -22.5 feet (-6.85 m) to discount the frictional resitance within the upper overburden zone. The pile was then drilled through the outer casing to the tip elevation of -65.02 feet (-19.8 m) with inner casing within the overburden zone. Strainmeters along with EDC were installed on dywidag bar at various locations and then wet set into the concrete following auger retrieval. The loads measured with EDC and Geokon sensors were within 15% percent of each other.PROJECT BACKGROUNDProject Background & Requirements:Like any other foundation piles, augercast piles are extensively used in the public and private sector structures in the United States for many years. It is a common practice to perform static compression (ASTM D1143), tension (ASTM D3689), and lateral load tests (ASTM D3966) depending on the project requirements. In recent years, embedded strain sensors, manufactured by Smart Structures, USA has gained prominence for its use to collect both static and dynamic measurements for driven piles. In addition, AVER has successfully used EDC for collecting long term static measurements for an abutment drilled shafts for I-95 Hotlanes project in Virginia, USA.Geokon sisterbar strain gages are widely used in the foundation industry to monitor the load transfer mechanism within pile foundations throughout the world. As the Geokon strainmeters are vibrating wire and are welded to a sister bar, there is often a debate within the engineering community with regards to what modulus to use when converting measured strains to loads. EDC sensors, unlike Geokon strain gages are embedded directly into the concrete and therefore do not have the same concern."

Jan 1, 1900