Search Documents

The importance of the minerals industry to any economy is clearly demonstrable. Its raw materials and products are the foundation of modem society and they have shaped the history of mankind from prehistoric times to the space age of today. However, those in the minerals industry have clearly failed to impress this fact on the consciousness of the public, bureaucrats and politicians. They have also failed to engage their dedicated opponents in a constructive debate. This is mainly because the minerals industry has been unwilling (until recently) to deal with the "soft" issues of civil society, nor understand and operate on a more emotional level. Technical professionals (as well as managers) in the future must be as comfortable in handling community concerns over social, environmental or landowner issues, as they are with logging complex drill core, designing blast patterns and separating one mineral from another. They must become caring, effective communicators and mediators. These are the new skills of a professional in the Third Millennium. These issues are outlined and discussed with some Australian data used to illustrate the point. If there is to be a future for all, then the policy makers within all levels of government (national, regional or local) must not drive essential mineral development offshore. They must address ways to support wealth creation mechanisms, particularly innovation. The minerals industry is a powerful wealth creator for ordinary citizens and an innovator. Politicians and their advisers must not .be allowed to forget this fact. If the ANZAC minerals industries do not win the emotional debate and successfully deal with the "soft" issues as well as they deal with the technical issues, there can be only a dim future ahead.

Jan 1, 2000

Adsorption experiments were conducted at two different solids loadings, to investigate the mechanism of oleate adsorption on apatite. Adsorption density at pH 10 was found to be dependent on solids loading in an oleate concentration region where surface precipitation could occur. Analysis of adsorption isotherms indicated three distinct regions of adsorption. In the region I (below the region of calcium oleate precipitation), molecular adsorption was observed. Simultaneous molecular adsorption and surface precipitation occurred in region II, while surface precipitation was predominant in region III along with some bulk precipitation. Correlation between flotation of apatite with sodium oleate and the mode of oleate interaction with the surface is established.

Jan 1, 1986

By C. Daniel Kealy

Dissolved and suspended solids are present in the free water of tailings ponds. This Bureau of Mines study was designed to identify the influences of the slime zone in preventing these solids from reaching the environment outside the tailings pond. The finite-element method was used to determine the rate of discharge of subsurface water from the Van Stone tailings pond in northern Washington. The slime zone was sampled and tested for the first time, and results were interpreted and incorporated into the mathematical model. Computer results were verified by installing and monitoring piezometers in the field and by a simulated (16- by 1/2- by 3 foot) laboratory model. Output from the numerical model defined critical seepage zones and revealed that proper pond design and maintenance can reduce pond seepage losses to a minimum. Minimization of seepage requires maintaining the pond water level over the slime zone. Sufficient physical, chemical, and limnological data were collected and analyzed to conclude that the only realistic reflection of synergistic effects is obtained by study of the indigenous biota in combination with quantitative chemical and physical data. Proper planning and management of the milling and waste disposal operations are the key to minimal pollution.

Jan 1, 1974

By W. L. Price

Since first introduced in the United States in 1964, rail mounted bucket wheel stacker-reclaimers have gained wide acceptance by users. The coal burning power plant group has adopted this new storage tool most quickly. The actual history is traced in this area in some detail. Installations in phosphate and steel mill ore storage and a listing of present users are included.

Jan 1, 1969

By W. A. Wood, W. H. Reimann, Maria Ronay

The basic mechanism of fatigue is studied in annealed a brass subjectecl to alternating torsion at room temperature, 100°, 200°, 300°, and 400°C, and in air. It is shown that the slip-zone micro-cracking which characterizes fatigue damage produced by small amplitudes at room temperature is progressively replaced by grain boundary cracking at elevated temperatures, replacement being complete at 400°C. Replacement occurs not because slip activity decreases hut because slip movements at elevated temperatures cease to concentrate in narrow zones and instead disperse. Decrease of amplitude at 400°C through permitting longer lives of specimens before fracture actually causes in- MOST studies of fatigue at elevated temperature have been concerned with data for design. Observations on the basic mechanism of fatigue have been largely incidental, though they have led to the interesting inference that this mechanism has features in common with that of creep.' This paper is concerned primarily with the mechanism itself. Advantage has been taken of mater- crease in pain boundary damage, an anomaly attributed to the greater difficulty at elevated tempwature of starting and propagating a crack. Surface corrosion was most pronounced along slip bands but since at elevated temperatures the slip hands showed no cracking the surface corrosion did not appear to influence onset and early spread of fatigue damage. Similarly the type of fatigue damage produced at room temperature by cyclic strain at large amplitudes, characterized by irregular mi-crocracks at zones between disoriented regions in a grain, was also replaced by mainly grain boundary cracking at elevated temperature, though not so completely. ials and procedures known to show readily how fatigue affects the microstructure of a metal at room temperature, so that direct comparison might be made with what the same procedures show when the material is subjected to fatigue deformation at higher temperatures. 1) MATERIAL This was 70/30 a brass, used extensively in previous studies at room temperature.' Specimens were turned from extruded rod to have parallel test portions 1-1/4 in. long and 7/32 in. diameter, annealed to a grain size -1/10 mm, and electro-

Jan 1, 1965

By Xiao-hui Fan, Xu-ling Chen, Zhi-yuan Yu1, Guanghui Li, Min Gan, Yun-song Huang, Tao Jiang

Compared with the traditional de-NOx processes by cleaning the waste gas, a new approach for reducing the formation of NOx during sintering process is proposed. Since more than 90vol% of NOx comes from the fuel combustion, the influence of sintering coke breeze pretreated by CO(NH2)2 additive on the NOx emission is researched. As adding CO(NH2)2, the reduction agents (NHi) are generated during the pyrolysis of CO(NH2)2, which reinforce the NOx reduction, And the appropriate content of CO(NH2)2 is 1.0 mass% of coke breeze.

Jan 1, 2015

By C. Chu

An investigation has been made of the radial heat-wave process using a mathematical model in two-dimensional cylindrical coordinates. This model considers combustion, convection and conduction inside the reservoir, but only conduction in the bounding formations. From a study of the general features of the process, an important phenomenon has been revealed, namely, the feedback of heat into the reservoir on the trailing edge of the heat wave. The effects of various process variables on the performance characteristics of the process have also been investigated. It was found that up to the time when the combustion front reaches a given point, the per cent heat loss, provided it is not higher than 40 per cent, is approximately directly proportional to the square root of thermal conductivity arid fuel content, but inversely proportional to the square root of gas-injection rate and oxygen concentration. The effecr of reservoir thickness is more pronounced, since halving the thickness doubles the per cent heat loss. The most decisive factor in determining the center-plane peak temperature is the fuel content of the reservoir. Within the temperature range investigated, doubling the fuel content doubles the peak temperature in the early stage, but the rate of decline of the peak temperature is high. Reservoir thickness is also a very influential factor. The peak temperature is lowered when the thickness is reduced; however, the effect of thickness becomes less pronounced when the thickness is high. Reduction of oxygen concentration increases the peak temperature in the early stage but lowers it afterwards because of the higher rate of decline of the peak temperature. Increase in gas injection rate or decredse in thermal conductivity geives a higher peak temperature which stays high for a longer period. The propagation range of the heat wave is chiefly governed by the fuel content of the reservoir. An increase of 0.2 1b/cu ft in the fuel content increases the propagation range by 100 per cent. The propagation range is more than doubled by doubling the gas injection rate, or reservoir thickness, or by reducing the thermal conductivity by 50 per cent. Comparatively, oxygen concentration has less effect on the propagation range. INTRODUCTION Several investigators have conducted theoretical studies of a radial heat wave. Vogel and Krueger1 studied a system with a moving cylindrical heat source of constant temper- ature, considering conduction in the radial direction only. Ramey2 included conduction in the vertical direction in his studies. Bailey and Larkin2 attacked a more general problem where initial well heating, vertical heat losses and arbitrary frontal velocities were included. In all these studies, however, conduction was considered to be the only means of heat transfer. Bailey and Larkin in a later paper included the effects of convection in a study involving both linear and radial geometries. Vertical heat losses were neglected in the radial case. Katz5 studied a similar problem in a one-dimensional radial model, using a heat-loss coefficient to account for vertical heat losses. Selig and Couch6 mployed a cylindrical model and investigated two limiting cases. In one case they considered no heat loss from the reservoir whereas in the other they assumed a constant temperature at the interface between the reservoir and its bounding formations. Thomas' studied a more general case but assumed a permeable bounding formation so that the convection effect is not confined to the reservoir. In the present work a more realistic and more generalized model is used. It involves a two-dimensional cylindrical system with combustion, convection and conduction inside the reservoir, but only conduction in the bounding formations. The purpose is to establish the temperature distribution both inside and outside the reservoir, to study the general features of the radial heat wave process, and to investigate the effects of various process variables on the performance characteristics of the process. THEORY We fist consider a circular porous reservoir of thickness H extending vertically from y = — H/2 to y = + H/2. The reservoir extends from a well bore radius r, to an external radius re. A stream of oxygen-containing gas is introduced into the reservoir through the wellbore. The oxygen-containing gas reacts with the fuel contained in the reservoir and forms a combustion front wherever the prevailing temperature can support the combustion. It is here assumed that this combustion front constitutes a cylindrical surface source of heat having an infinitesimal thickness in the radial direction and extending vertically throughout the whole thickness H. This is designated as Region I. We next consider a Region II corresponding to the upper and lower formations bounding the reservoir, extending from y = — - to y = — H/2 and from y = + H/2 to y = + m. Since r, is very small, we may assume that the two bounding formations have the same dimensions, symmetric with respect to the center plane of the reservoir. In this way, we may take the upper half of the system alone into consideration. In contrast with

By Armin Iravani, Changping Yi, Matthias Wimmer, Daniel Johansson, Santiago Gómez, Håkan Schunnesson

Sublevel caving (SLC) is a mass mining method based upon the utilization of gravity flow of blasted ore and caved waste rock. Drilling and blasting are the initial and the major impact on primary fragmentation and later material flow characteristics. The heterogeneity of rock mass has a great impact on materials’ mechanical properties and plays a significant role in rock fragmentation by blasting. In this work, a numerical model for sublevel caving based on 3D Voronoi tessellations was developed to section rock mass into arbitrarily shaped regions for modelling the heterogeneous rock mass. A coupled finite element and discrete element method was employed to investigate both the fragmentation due to blasting and the gravity flow of ore in a heterogeneous orebody. In the coupled model, the caved waste rock was modelled with loose discrete particles while the orebody to be blasted was simulated with bonded particles. The detonation of explosives was described with a particle blast method and a finite element model was used to model the remaining orebody. The results indicated that the fragmentation at the upper part of the ring is coarse while it is fine at the lower part of the ring. The heterogeneity of rock mass induced some boulders after blasting.

Feb 6, 2023

By H. H. Schrenk, Carlton E. Brown

"INTRODUCTION The angle at which a hole is drilled has long been thought to affect the amount of dust disseminated into the air during wet drilling. The amount disseminated has been reported as increasing rapidly with the approach of the angle of the hole to the vertical (up) position. 4/ This has been explained commonly as being caused by a decrease in contact of water with the face of the drill hole; increase in amount of sludge dropping through the air; and increase in amount of sludge running down the drill steel and being thrown into the air by the rotation of the drill steel and by leakage of air from the front head of the drill.The steep up angles of the holes drilled are responsible, at least partly, for the higher dust concentrations found in such places as raises, compared with those at level faces, where most of the holes are drilled at angles farther from the vertical (up) position. The mining industry is coming to realize more and more the importance of the angle of the drill hole as a contributing cause of the high dust concentrations found in some raises. Much work is being done to counteract the effect of the angle of the drill hole on dust dissemination. The rate of rater flow through drill steels is being increased by the use of water tubes of larger diameter or by higher water pressures to obtain better contact between water and the face of the drill hole. Traps are being developed to catch the sludge from the drill hole and allow it to drain down through a special pipe before it drops through the air or runs down the drill steel. Drills that permit little or no air to leak from the front head along the drill steel are being designed and used. Care is being taken to prevent the exhaust from the drill dispersing the sludge into the air."

Feb 1, 1938

By Emanuel Trotz

As the long-felt need of a reliable and easily-managed pyrometer has now been fully supplied, by the latest form of Professor Wiborgh's pyrometer, an account of this instrument will, per-

Jan 1, 1893

By G. Song

"SynopsisAccording to the overlying rock strength and thickness of 10 shallow coal seams in China, the strata are classified into four types: weak and laminated strata (hereinafter referred to as WL), weak and massive strata (WM), strong and laminated strata (SL), and strong and massive strata (SM). The four types of strata, together with longwall panel height (M), panel length (L), and seam depth (H) are factors that influence the loads on hydraulic power supports. Principal component analysis was used to study the seven influencing factors. It turns out that seam depth (H) is multicollinear with WL, WM, SL, and SM. Thus the enumerated seven factors are divided into two models. In Model 1, six factors; panel height, panel length, and layer thickness of the four type strata are involved. In Model 2, three factors; panel height, panel length, and seam depth are included. Using multivariate regression analysis, two equations to calculate loads on supports are obtained for each model. The equations were applied to shallow coal seams. The equation of Model 1 is more accurate than that of Model 2, but Model 2 could be further used in deep coal seams. The equations were coded through VB programming to simplify the calculation.IntroductionTo ensure coal production in the long term, the focus of coal mining has been gradually shifted to the western areas of China in recent years due to rich coal resources in this region. Most of the coal seams in this area are shallow but the support loads are abnormally high. In these circumstances, the chock loads estimating methods used in the past do not work. If the rated working resistance of a support is larger than needed, the shield is unable to fully perform, while a lower working resistance would lead to accidents like shield crushing or even casualties. This problem is frequently found in shallow coal seams such as Shenfu-Dongsheng, Yulin, Tuha, Lingwu etc. (Zhang, 2011). Thus, to ensure safety and efficiency during mining, the estimation of support loads and selection of supports are of great significance."

Jan 1, 2015

By SAIMM SAIMM

To the members of The South African Institute of Mining and Metallurgy We have audited the annual financial statements of The South African Institute of Mining and Metallurgy set out on pages 575 to 586 for the year ended 30 June 2005. These financial statements are the responsibility of the Institute?s Council. Our responsibility is to express an opinion on these financial statements based on our audit. Scope We have conducted our audit in accordance with International Standards on Auditing. Those standards require that we plan and perform the audit to obtain reasonable assurance about whether the financial statements are free of material misstatement. An audit includes: examining, on a test basis, evidence supporting the amounts and disclosures in the financial statements, assessing the accounting principles used and significant estimates made by management, and evaluating the overall financial statement presentation. We believe that our audit provides a reasonable basis for our opinion. Audit opinion In our opinion, the financial statements fairly present, in all material respects, the financial position of the Institute at 30 June 2005 and the results of its operations and cash flows for the year then ended in accordance with South African Statements of Generally Accepted Accounting Practice.

Jan 1, 2005

By A. C. Apling, N. B. Barrett

Roadstone production requires the generation of non-flaky material, as outlined in British Standard 812 section 105.1; with respect to this criterion, a mathematical model of a cone crusher must be able to predict the flakiness index of a particular size range as determined by the relationship between thickness and nominal size. The Whiten cone crusher model utilises breakage and classification functions to predict a product particle size distribution only, so a shape function has been proposed that is based on a phenomenological approach, taking into account the transfer between flaky and non-flaky material at each stage of breakage. The results of laboratory tests to determine material breakage characteristics and of examination of pilot-scale test products illustrate the method's potential

Apr 1, 1995

By James P. Rider, Robert P. Vinson, Fred N. Kissell, Jon C. Volkwein, Gregory J. Chekan, Jay F. Colinet

The Thermo-MIE personal DataRAM dust monitor (pDR) is a light-scattering instrument approved for use in gassy underground mines by the U.S. Mine Safety and Health Administration (MSHA). However, the use of lightscattering monitors has been inhibited by concerns about inaccurate readings resulting from changes in dust size distribution and composition, as well as concerns about the impact of moisture in the mine air. Because of this concern, the National Institute for Occupational Safety and Health (NIOSH) has evaluated the pDR using available data from laboratory tests and mine surveys. The data show that accuracy can vary widely from test to test and mine to mine. In most cases, the results can be improved by using a companion gravimetric measurement to adjust the pDR data.

Jan 1, 2005

By E. Scott Bair

Renewed interest in the vast reserves of anthracite coal in eastern Pennsylvania led to the use of a numerical model for simulating the hydrologic effects of constructing an open-pit anthracite mine. The proposed mine would be approximately 1800-m (5900-ft) long, 1000-m (3300-ft) wide, and 300-m (1000-ft) deep. A two-dimensional, finite-difference, ground-water flow model was used to calculate ground-water seepage rates into the proposed mine, to evaluate the effectiveness of various deep-well dewatering systems, to calculate drawdown in adjacent wells and properties, and to estimate the capacity of the water-treatment plant. Site-specific values of pertinent hydrogeologic parameters were used in the simulations.

Jan 1, 1980

By Joaquim Luiz Monteiro de Barros, Fabiana Moreira Costa

Este trabalho tem como objetivo principal apresentar de forma didática e através de exemplo prático, os processos de limpeza de gases de exaustão durante a produção de ferro e aço para atendimento as normas ambientais e a possibilidade da recuperação de energia térmica desses gases captados para aumento da eficiência energética das plantas siderúrgicas.

Aug 1, 2019

By Jay C. Hanson

Various electrical and electromagnetic (EM) geophysical techniques are currently being evaluated by the U.S. Bureau of Mines for their effectiveness in the detection and monitoring of electrically conductive (1 to 5 S/m) lixiviant (leach solution) to depths of 600 m, either above or below the water table. These techniques include magnetotellurics (MT) , controlled source audiofrequency magnetotellurics (CSAMT), resistivity and focused resistivity, ground-penetrating radar (GPR), frequency-domain electromagnetics (FEM), and time-domain electromagnetics (TEM). Of these techniques, TEM may be the most effective, but CSAMT and focused resistivity also hold promise. Geophysical computer modeling of the borehole TEM technique was conducted based on an idealized geoelectric section (layered earth) with characteristics based on the Santa Cruz porphyry copper deposit near Cas a Grande, AZ. Layer resistivities and thicknesses were obtained from geophysical data and geologic logs available from the site. Modeling of borehole TEM in both preleach and during leach situations was conducted. Simulating the TEM method using computer modeling proved to be encouraging since there were substantial differences between leached and nonleached responses. The modeling does not prove the effectiveness of TEM in the field, but does indicate that detection of deep lixiviant zones is theoretically possible.

Jan 1, 1992

By H. Meseck

Dynamic pile test methods to establish the bearing capacity of driven piles were developed in the USA more than 20 years ago. In the Federal Republic of Germany, the first dynamic pile tests were carried out at the end of the 70's. Today dynamic pile tests are successfully used to establish the integrity and bearing capacity of driven and bored piles. The Institute of Foundation Engineering and Soil Mechanics at the Technical University of Braunschweig has developed its own method of measuring and evaluation for the execution of dynamic pile tests. The principles of the dynamic pile tests, the measuring and evaluation plant as well as the experience gained with it in the examination of cast-in-place piles are presented in this contribution.

Jan 1, 2010

By D. C. Torre

The coal mining industry has long recognized the need for a system capable of hauling mined coal from the face in a continuous flow. More than 30 years ago, successfully operating continuous haulage systems were first placed in the field. There were a few individually successful applications. However, the truly successful use of such systems really only began in the early seventies. Today, a variety of systems are available from a number of manufacturers. Even so, continuous haulage has not achieved the acceptance and application it would seem to have earned. There is a need for more productive, cost-effective, and safer methods of hauling coal from the face. There is also a need to speed up development for longwall operations. And continuous mining is not really "continuous" unless it is supported by a reliable continuous haulage system. Despite all this, most of the coal producers have failed to exploit the successful continuous haulage systems offered by several manufacturers. In the 1970s, many of the top coal producers tried a continuous haulage system but gave up on it and on the concept. In some cases, major coal companies had systems operating successfully in one mine, or even one division. But their use did not spread to others of their mines or divisions. Frequently, their use was eventually abandoned, even in mines where it had been successful.

Jan 1, 1990

By Oliver Bowles

Slate possesses many admirable qualities, not only as a roofing material, but for blackboards, electrical switch boards, and for various structural uses such as stair trends, floor tile, baseboards, and sanitary enclosures. The American slate industry was established manor years ago, and has made remarkable progress, particularly during the past five years. One of the chief drawbacks to more rapid expansion is the high percentage of waste which reaches 75 to 94 per cent of gross production. Much of this waste is duo to rock imperfections over which man has no control, but a careful study of tae industry by the Bureau of Mines over a period of years indicates that an undesirably large percentage of the marketable slate is wasted in the processes of quarrying and manufacture. The initial step in quarrying slate is to separate from the solid ledge masses of a size that ray be conveniently removed from the quarry. This first step entails a greater waste of material than any subsequent process, and, therefore, invites the most earnest effort toward waste reduction. Attention has consequently been directed toward possible improvements in methods of making primary cuts in the quarry floor. A study of European practice with the wire saw, together with theoretical consideration of its advantages, convinced the writer that it possessed sufficient merit to justify its use as a primary slate cutter in American quarries. No practical conclusion in this matter could be reached except by experiment. Therefore, the desirability of obtaining equipment and trying it out under actual conditions of operation was urged upon operators. While no doubt the equipment could be readily manufactured in America, it had already been developed to the point of practical use in Europe; therefore the writer urged the desirability of purchasing one completely equipped wire saw in Europe, and determining through tests whether it gave sufficient promise of success to warrant its manufacture in America.

Jan 1, 1927