Search Documents

By A. E. Raddatz

In an attempt to develop technology to use domestic resources in place of imported bauxita, the Bureau of Mines investigated sulfurous acid leaching to extract alumina from kaolin. The process consists of leaching the calcined kaolin with a 30 wt-pct S02 solution at 60° C and 160 psig for 17 hours, fil¬tering the leach slurry, precipitating monobasic aluminum sulfite from the filtrate at 110° C and 60 psig, a& decomposing the sulfite in the spent liq¬uor at 150° C and 55 psig to produce crude alumina. Purification of the crude alumina was accomplished using a modified Bayer process. Results from closed-circuit tests employing the sulfurous acid process showed that overall extraction of alumina from kaolin was 67 pct. Production of 1 ton of alumina would require 3.6 tons of calcined kaolin, 0.7 ton of sul¬fur dioxide, and 8.4 tons of water. After purification by a modified Bayer process, the alumina product contained the following; impurities, expressed in weight-percent: Fa203, 0.009; S, 3.6; Si02, 0.07; Ti02, 0.002; K20, 0.017; and P205, 0.03.

Jan 1, 1981

By L. A. Wilson, N. H. Harrison, R. R. Clay, R. L. Reed. D. W. Reed

Experiments have been performed in a linear near-adiabatic system for the purpose of extending data on reverse and forward combustion from atmospheric pressure to 1,000 psig. Results obtained from reverse combustion appear to conform qualitatively with the existing description of the process when reaction kinetics are suitably modified to account for the increase in pressure, i.e., increasing tbe pressure decreases the peak temperature and increases the combustion zone velocity. Forward combustion appears to be a fuel dominated process wherein peak temperature and combustion zone velocity are not very sensitive to changes in pressure. The moderate effects of pressure that do exist at low flux virtually disappear at high flux providing all oxygen is consumed. With this provision. increasing the pressure decreases the frontal velocity and increases the peak temperature. Results me shown graphicaIIy which demonstrate the effects of presswe on peak temperature, rate of advance, oil recovery, air/oil ratio, carbon oxides produced and temperature distributions. INTRODUCTION Numerous field tests of oil recovery using the technique of underground combustion are now in progress. Operating pressures used are always substantially in excess of atmospheric pressure. Nevertheless, the literature contains no laboratory data pertaining to the effects of pressure except for those of Martin, Alexander and Dew.1 Unfortunately, these data appear to reflect heat losses which may have obscured some of the effects of increased pressure. The underground combustion processes are exceedingly complex, and general concepts relating to them have necessarily been described in relatively simple terms. Particularly with regard to forward combustion, the interaction between multiphase fluid flow, heat transport and various rate mechanisms is so involved that to date a rigorous treatment is not available. In this paper a linear near-adiabatic system is described which was found capable of operating at pressures up to 1,000 psig and temperatures of at least 1,100 F. Using this equipment, experiments on both forward and reverse combustion were accomplished at elevated pressures and the data presented as a function of air flux or temperature. It will be assumed that the reader is familiar with the papers of Wilson, Wygal, Reed, Gergins and Henderson on forward combustion and that of Reed, Reed and Tracht3 on reverse combustion, so that it is not necessary to repeat the details of the two processes. EQUIPMENT AND PROCEDURE It was decided to study the effects of pressure over the interval 0-1,000 psig using a near-adiabatic system. Since satisfactory operation of such a system requires very thin tubing walls, it proved necessary to insert the entire combustion tube and heater assembly into a high pressure jacket in such a way that the internal tube pressure could be counterbalanced by pressurizing the annulus. This meant that the numerous heater and thermocouple wires had to pass through gas-tight seals that required considerable effort to maintain effective. An unexpected difficulty arose in connection with the nature of the annulus pressuring gas. It turned out that the composition of this gas critically affected the functioning of the adiabatic control system. Operation of the equipment at elevated pressures was not particularly difficult. The problems that did arise were a direct consequence of the large numbers of connections and seals involved. EQUIPMENT The equipment consisted of the combustion tube which fitted within the pressure jacket. This jacket was in turn mounted on a wheeled carriage which facilitated movement and provided for rotation of the

By John C. Stankus

Jennmar Corporation. in an effort to improve mine roof control, has conducted extensive study and research comparing tensioned point anchor resin systems versus the use of non-tensioned fully grouted rehar. Preliminary indications are showing that in thinly laminated, weak strata, tensioned point anchor resin systems are providing more effective roof control than the non-tensioned fully grouted rehar. In this paper two case studies are presented in which tensioned point anchor resin systems were utilized to stabilize and control the mine roof in two different mines. Both mines are alike in many ways, but yet very different in other aspects. However, the mines do share one main common factor. and that being the non-effectiveness of the non-tensioned fully grouted rebar in controlling the thinly lamininated strata in each respective mine.

Jan 1, 1990

By Tripathy A. K, Satapathy B. K, Nayak B, Mohanty J. N, Dey D. N

The paper deals with the metallographic tudy of heat treated chromite and chromite-coke composite briquettes. The briquettes, prepared from chromite concentrate of Orissa Mines using molasses-lime, dextrinelime and tamarind seed as binders, were subjected to different temperatures and examined metallographically. The change of phase with temperature was analysed by X-ray diffraction.

Jan 1, 1987

By Daniel Brutto

"Environmental considerations are a key driver within marine mining consenting processes across different national and international legislative regimes and are critical in shaping the global public perception of the industry. As a result, it is vital that mining companies seeking to operate within marine environments establish a robust understanding of the sensitivities of the seabed environments in which they are active, the impacts of their activities and the ability of the environment to recover from these impacts. The significant risks of failing to do so include an inability to either obtain or maintain operating permits. At the individual project level, the environmental effects of any given development project are typically defined within the scope of an Environmental Impact Assessment (EIA). For well-established industries operating in well-studied environments this approach typically works well. However, where emerging industries or existing industries that are operating within new environments are concerned, there may be significant knowledge gaps pertaining to our understanding of how specific anthropogenic practices or activities interact with the marine environment. These knowledge gaps can cause significant uncertainties pertaining to the likely significant effects of a project. Such uncertainties may result in barriers to industry and economic progress, increased consenting risks, increased project costs to be borne by individual project developers through the acquisition of additional environmental data during the pre-consent or post-consent project phases, project delays and/or significant increases in environmental monitoring burdens with corresponding increases in project costs."

Sep 1, 2014

By Juan Roldán

El presente trabajo refiere la política de creación, formación y futuro de la Escuela de Minas de Recuay en el ámbito de la minería nacional e internacional. Para ello, se revisa los fundamentos del proyecto, antecedentes, organización, formación y perfeccionamiento del personal, métodos de enseñanza y conclusiones.

Nov 1, 1976

By Paulo Sérgio Moreira, Geraldo Lúcio de Faria, Rhelman Rossano Urzêdo Queiróz, Amanda Aparecida Fátima Arruda, Ana Cecília de Carvalho

O objetivo deste trabalho foi avaliar o desempenho em desgaste de camadas espessas de óxidos formadas na superfície do aço inoxidável ferrítico 410D após a sua submissão a tratamentos isotérmicos em atmosfera oxidante. O aço em questão foi estudado no estado de entrega e tratado isotermicamente nas temperaturas de 900°C e 1000°C por diferentes intervalos de tempo. O método de avaliação empregado foi o teste de desgaste micro-abrasivo do tipo esfera presa em placa. Com o desenvolvimento do estudo, foi possível executar análises qualitativas e quantitativas a respeito do comportamento em desgaste do aço inoxidável 410D em função de sua condição superficial, como oxidada ou não. Alterações microestruturais também foram consideradas na discussão dos resultados. Concluiu-se que a camada superficial de óxidos desenvolvida após os tratamentos isotérmicos possui boa aderência e tem potencial para aplicação como camada protetora do aço em aplicações onde a sua resistência ao desgaste seja requerida.

Oct 9, 2019

By R. Ghomashchi

Wear, fatigue and corrosion are the most widely encountered modes of failure in materials used in engineering applications, including aero-gas turbines. Although wear is distinctly classified as adhesive, abrasive, erosive, fretting and so on, there are usually more than one wear mechanism involved in the failure of components in service because there are many systems and materials variables active in materials wear that makes it more difficult to study. This is further complicated by the discrepancies between the results of laboratory tests and field data. The present investigation was set up to examine the wear characteristics of M50 and T1 high-speed steels at both room and elevated temperatures to draw a thorough understanding of the wear behavior of this class of high-speed steels. This article focuses on the mechanical and microstructural characterization of wear for T1 and M50 high-speed steels using a pin-on-disk wear machine.

Jan 1, 2005

By L. W. Emery

Undergrorlnd combustion operations were initiated in a 60-acre Bartlesville sand "shoe-string" reservoir in Allen Connty, Kans., in 1956. Tests in separate patterns were conducted using various co~nbinations of air and recycle gas to propagate combustion fronts from the injection toward the producing wells. These patterns were made up of 6 injection and 20 prodrrcing wells Gas and liquid prorluctiorz from each pattern was measured on an individual-well basis, and comparisons were made between the three patterns to ascertain the relative effects of injected gas composition on production behavior. Breakthrough of the combustion front at a well was characterized by an increase in water production from the well followed by an increase in bottomhole temperatrrre to approximately 250" F. After burning fronts had broken through at five producing wells, operations were terminated in 1960. From the total project approximately 79,000 bbl of oil were produced during thermal operations at a cumulative produced GOR of 23 Mcf/bbl. No appreciable change in the character of the produced crude was observed. Combustion in the reservoir was maintained with injected gas compositions ranging fronz 6 per cent oxygen in recycle gas to 100 per cent air. lnjectiotz of large quantities of recycle gas resulted in higher producing GOR's from offset wells than were measured from a pattern into ~vhich straight air ~vas injected. The air required to move the combustion front through I acre-ft of reservoir was computed to be 20 MMscf. This valrre was found to be relatively independent of the quantities of recycle gas injected. The recovery efficiency from the swept area was esti~izated to be about 59 per cent. Areas swept were similar in shape to tlzose obtained with a laboratory potentiometric model. Samples of sund taken from behind the burning front by coring indicated almost total oil removal from the sand. Petrographic analysis of the core samples indicated that the sand had been heated to peuk temperature of rlbout 1,200" F. No rignificant difference in peak temperature was forrnd in two areas where compositions of injected gas were quite different. Compression costs for thermal recovery were estimated to be $1,20/bhl of produced oil. INTRODUCTION The use of the "forward combustion" process as an oil recovery method has received a great deal of attention. This method involves ignition of the formation in an injection well, followed by propagation of a combustion front through the reservoir. Combustion is maintained by the injection of an oxygen-containing gas to react with reservoir hydrocarbons. As the flame front progresses through the reservoir, oil and formation water are vaporized, driven forward in the gaseous phase and recondensed in the cooler part of the formation. In turn, the condensed fluids push oil into the producing wellbores. Completed field tests of the process were first reported by Kuhn and Koch,' and by Grant and Szasz.' Results from other tests have since been reported by Walter,3 by Moss, White and McNeil,' and by Gates and Ramey." ach of these tests essentially utilized a single injection well surrounded by four or more producing wells. Sinclair Research, Inc., elected to do field experimental work using a number of test patterns in a single field in order that comparisons between various operating schemes could be made. The site selected and purchased in 1955 for this experimental work was a 60-acre Bartlesville sand reservoir located in Allen County, Kans. Combustion operations were initiated in mid-1956. Between that time and termination of the project in mid-1960, combustion fronts were propagated from injection wells to producers in three separate well patterns, using different mixtures of air and recycle gas. The test was terminated before sweep of the three patterns was complete so that information about the effect of combustion on the swept areas could be obtained by coring. Results from the test in the form of injection and producing well performance have been carefully recorded, and these form the general basis for this paper. DESCRIPTION OF RESERVOIR The reservoir in which the combustion tests were conducted is a Bartlesville sand "shoe-string", typical of a number of small reservoirs in Southeastern Kansas. Average reservoir characteristics are shown in Table 1. Fig. 1 is an isopachous map of the producing sand showing the reservoir to be approximately 400-ft wide and 2,500-ft long. Maximum net productive sand thickness is 21 ft. Fig. 2 shows a typical core analysis obtained by coring with water-base mud. The reservoir has no appreciable dip and is closed on the sides by degradation of sand into shale. The main body of sand is heavily laminated with shale stringers, which are not continuous between wells. The main reservoir is overlain by 30 to 40 ft of laminated low-permeability sand and shale streaks. No information is available on the original properties of

By A. M. Martinez, L. Melis, R. C. Peláez, L. G. Garcia

Orovalle Minerals S. L. operates a copper/gold mine in the Asturias region of northern Spain, with the operation dating back to December 1997. The feed to the El Valle mill, consisting of oxide/sulphide (skarn) mineralization, is highly variable, even on a shift by shift basis and presents challenges to the mill operating staff on a daily basis. The mineralogical characteristics of the ore are quite complex with copper present as native copper and sulphides as well as copper minerals with deleterious elements. Gold is present as native gold and electrum. The mill circuit includes SAG/ball mill grinding, gravity recovery of native copper and gold, flotation of copper concentrate, carbon-in-leach gold recovery and SO2/air cyanide destruction. The paper will provide a description of the different unit operations and present operating data of the mill operation.

Jan 1, 2019

By C. J. Wilhelm

The disposal of brines produced with crude petroleum and natural gas has been a long-continuing problem to oil and gas operators as well as to farmers and stock-raisers in the vicinity of producing fields. An impartial appraisal of conditions pertaining to the problem of brine disposal leads to the conclusion that study of the technical consideration, with proper weight given to the economic and social factors, is the most desirable approach to this problem. Brine disposal is a problem of such magnitude in certain areas in the State of Kansas that in August 1934 a cooperative agreement was made between the Kansas State Board of Health and the U. S. Bureau of Mines for a cooperative technical study of methods of brine disposal.

Jan 1, 1935

By E. R. Maize

[he scconG rcport of :his st?rI.org 8cdt with o3servatioi:s of conver- gence of roof an4 floor at t!x*re: ?.cc.-.tioris iri til~ ClVucible mine of kke Cru- cib1.o Fuel Co. Data on sl:'ociacnce ?.rd Lztcrcl mwe:~cnt cf the surface were .:lven for two of these areas, a-12 it was mentioned that ~lr~~ilar data were being obtained on a ?art of Pe:sc:rlvtzr.ia Fii~l?trr.y FE:, ~i!lic;l pcser: over the third area. 'I'hie hichw~ :LEO FasseE over t!lc ITenncoli::. :.line of the Bnckeye Coal Co. 9 milcs to ';he so-lth, cnd at P. l~tcr C'..att: ~.nr?r.,cc?r:cntS *.rere mnd.e to make similar observati on3 there. This y: pr mrnmri:.c n Czto obtnino? at those two locetionn,]

Jan 1, 1941

By Honggang Zhong, Xin Cao, Qijie Zhai, Hongmei Song, Congsen Wu, Cheng Zhang, Jingzheng Ye

"The influence of superheat on the solidification structure and ferrite/austenite phase transformation of a novel lean duplex stainless steel (DSS) was investigated on a setup, which designed to thermally simulate the continuous casting process. The results showed that the macrostructure of the samples all exhibited chill zone, columnar zone and equiaxed zone. The distance from chill zone to position of columnar to equiaxed transition (CET) moved from 51.0 mm to 39.8 mm with an decrease of superheat from 70 °C to 10 °C, and that the grains in the chill zone tended to be finer. In equiaxed zone, the fme and uniform grains were observed when superheat higher than 40 °C; while, coarse grains were found in samples poured at low superheat. Generally, the volume fraction of ferrite increased along the dendritic growth direction, and stabilized in equiaxed zone. The high superheat decreased the volume fraction of ferrite in equiaxed zone, while it had indistinctive influence on chill zone and columnar zone.IntroductionDuplex stainless steel with approximately equal volume of ferrite and austenite, offering an attractive combination of corrosion resistance and mechanical properties. [ l]. The production of DSS, worldwide application in structural engineering[2] and petrochemical industry[3], have increase by more than 100% in the latest decade[4]. But due to the sharp prices increase of nickel and chromium, lean duplex stainless steels which have lower contents of alloy elements were developed. They perform well in both mechanical and corrosion resistance[S, 6] and even have TRlP(Transformation Induced Plasticity) effect[?]. Nonetheless , the mechanical properties of DSS was affected greatly by the solidification structure, such as columnar to equiaxed transition (CET), grain size and phase content[8]. So, the solidification behavior of stainless steel was investigated widely"

Jan 1, 2014

By Ramanathan C, Prasad P. V. S. R

The most critical challenge for any large size storage structures to be constructed on soft compressible soils is bearing capacity and consolidation settlements. Consolidation is the time dependent phenomena, as expulsion of water from soil voids on application of external load will take longer period. It is mainly influenced by soil consistency, permeability, thickness of compressible stratum and presence of free draining layers. This study deals with the foundation solution of a large size Mounded Storage Vessel (MSV) to be constructed on thick compressible stratum whose loading intensity is around 155 kPa and the estimated settlements are greater than 400 mm. Hence, the foundation solution using vibro stone columns is adopted as an effective technique to address the challenges of excess settlements and inadequate bearing capacity. Further to keep settlements within the permissible limit of 50 mm, preloading technique with 60% of actual loading intensity will be utilized. The consolidation analysis of stone column reinforced foundations is carried based on the method given by Han and Ye (2001). The quality of the stone columns is ensured by real time quality control measures and the performance of the stone columns shall be ensured by vertical load tests. Ground settlements was closely monitored with proper instrumentations and the actual degree of consolidation has been verified by Asaoka’s (1978) method.

Sep 1, 2022

Design and test a high-production coal mining machine that generates less respirable dust. Background Current coal cutting systems generate excessive amounts of airborne respirable dust and fines during the mining process. Dust control technologies, including dust dilution by ventilation and suppression by water sprays, are not always able to reduce dust levels sufficiently. The U.S. Bureau of Mines (USBM) has designed a cutting system that reduces respirable dust generated by the cutting action of the drum. This cutting system, based on geometric principles developed in the 1500's, makes use of a constant depth, linear cut to remove coal at deeper cut depths and at lower rotary speeds than a conventional rotary drum. A comparison of the linear and rotary cut paths is shown in figure 1. Approach A full-scale prototype of the linear cutting concept was valuated under laboratory conditions to determine its performance relative to standard rotary drums. Results of these evaluations show production of fewer fines, or more uniform product size, a significant reduction in the amount of airborne dust, and reduced torque and power requirements (figure 2). On the basis of these results, a contract effort was undertaken by McCracken and Associates of Bristol, TN, to design a linear cutting head for underground testing.

Jan 1, 1995

By Ellis S. Hertzog

The material published in this report is part of a special study of some of the chemical and physical properties of Alabama coals. The complete study included friability and grindability determinations, high and low temperature assay distillation tests, and ash fusion-temperature determinations. Proximate and ultimate analyses and. calorific values of the coal samples also were obtained. This paper is concerned only with grindabilities, although proximate analyses have been included to give a better picture of the problem as a whole. The growing interest in grindabilities of coals is a result of the increase in use of pulverized fuel in REscent years. The tenative ball-mill grindability method D409-35T4/was used in making all the determinations. The method of sampling and the technic of the testing procedure is described in Considerable detail in this report because the procedure was established quite recently. The ball-Mill grindability index is a measure of the ease with which coal may be ground, which may be an important factor in estimating pulverizing costs. Up to the present time few data on the grindability of Alabama coals have been published. The data in this paper show that the Warrior and Cahaba fields exhibit a wide range of grindability in their coals. The mines tested are well distributed throughout the productive areas of these fields, and it is possible to make rough estimates of the grindabilities of coals not listed in this report from the data given for mines situated in the same vicinity. ACKNOWLEDGMENTS This study was conducted at the Southern Experiment Station of the Bureau of Mines in cooperation with the University of Alabama. The Alabama liming Institute was of great assistance in furthering the investigation, and the work was undertaken largely as a result of its request that the Bureau of Mines should make certain studies of Alabama coals. Grateful acknowledgments

Jan 1, 1938

By Y. S. Sun, P. Gao

Compared with conventional roasting and magnetic separation processes, higher reduction temperatures and stronger reducing atmospheres are used in reduction technologies to reduce iron oxides to metallic iron, which is often liberated during reduction and amenable to magnetic separation. Reduction and magnetic separation of an Australian refractory iron ore was therefore studied as a function of reduction temperature, time, coal addition, feed thickness and size of Australia iron ore. It was found that during reduction, the particle size of the reduced iron increased with reduction temperature and time. Subsequent magnetic separation tests were further conducted on the reduction products. A reduced iron powder with a Fe grade of 85.67% was obtained at a Fe recovery of 87.82% under optimum reduction conditions where a metallization rate of 85.82% was achieved. The mechanism involved in reduction is discussed based on XRD and SEM examinations. And the results indicated that theiron minerals such as hematite and limonite in the Australian iron ore were reduced as follows: Fe2O3?Fe3O4?FeO?Fe. Furthermore, the metallic iron particles produced by reduction increased in size with longer reduction times.

Jan 1, 2014

By N. Jayaraman, V. Srikant, A. Radhakrishna

Addition of a 500 MW unit to the existing units at Ramagundum Thermal Power Station requires blasting of large volumes of rock very close to sensitive installations like Turbo generator, Generator transformer and Power cycle equipments. Levelling of the areas and excavations for footings are, therefore, to be carried out cautiously. The existing sensitive installations should be protected against ground vibrations and flyrock. The paper describes the details of a few of the many blasts carried out successfully wherein the ground vibrations were restricted and flyrock was avoided.

Jan 1, 2003

By A. J. Maselli, E. C. Cemak

Hartford Steel Technologies (HST) has a pyrometallurgical and hydrometaliurgical process capable of reclaiming valuable metals from a hazardous waste· stream such as EAF Dust. The HST Process effectively addresses the growing environmental concerns surrounding the increasing production of EAF Dust without producing any hazardous waste material as byproducts. Currently EAF Dust production levels are exceeding the 1,000,000 metric tons per year mark. The HST Process is designed to separate iron, zinc, lead, cadmium, copper, and silver metals using a two-phased process. The Pyrometallurgical side of the Process utilizes a Rotary Hearth Furnace to separate the iron metal from the remaining metals. These remaining metals are further separated, using a Hydrometallurgical Process, in a series of digestion tanks. The individual metals are then collected in saleable form.

Jan 1, 2000

By John C. Machisak

THIS CHAPTER of the Minerals Yearbook (Volume III) contains overall injury experience for coal mines, both anthracite and bituminous, coke plants, petroleum and natural gas, peat, and asphalt and related bitumens (native); metal mines, their metallurgical plants, including ore-dressing plants and primary nonferrous reduction plants and refineries; nonmetal mines; nonmetal mills; sand and gravel operations; slag (iron blast-furnace) plaints; and stone quarries and their related pants. Volume I of the yearbook contains a chapter showing injury experience and employment data treated separately by metal mines, nonmetal mines, quarries and their related plants, metallurgical plants (ore-dressing plants and primary nonferrous reduction plants and refineries are shown separately), nonmetal mills, sand and gravel plants, and iron blast-furnace slag plants. Volume II contains injury and employment experience in the fuel industries (coal, coke, petroleum and natural gas, asphalt and related bitumens (native), and peat. Injury and employment data are submitted voluntarily for the mineral operations through an industry canvass made by the Bureau of Mines, except for the coal industry, whose reports are mandatory. Information published in this chapter is the result of this canvass. Figures presented in this chapter for 1961 are preliminary except for anthracite, peat, coke, petroleum and natural gas, asphalt and related bitumens, and slag. These preliminary data, with the exception of bituminous coal, are a summation of reports received by May 31, 1962, from the operators showing their injury and employment experience. Estimations of injury and employment experience are not included in these preliminary data.

Jan 1, 1962