Search Documents

By J. R. Martson

The arrangement of the larger furnace at the United Verde smelter, together with the boiler layout and connecting flues, is shown in Fig. 1. The important dimensions are given in the figure, and cross-sectional areas of combustion space, flues, etc., are recorded. The location and extent of the baffling in the boilers also are shown because of their importance in the interpretation of the data. Two boilers serve each reverberatory furnace. They are of the class M-26 Stirling type (rated at 713 boiler hp. each). Steam is generated at 178-lb. gage pressure at a total temperature of 528" F., from feed water at a temperature of 113" F. The feed water is condensate from turbogenerators plus make-up softened by the lime-soda process. The make-up is rather large in amount as it must match the amount of steam consumed in reciprocating blowing engines and the like, which are not served by surface condensers. As a result the boiler feed water has a hardness of 1.5 to 3.0 grains per gallon, but this results in the formation, during six months to one year of boiler operation, of scale only of "eggshell " thickness or less. The boilers are set at the same elevation as the tapping floor of the furnace, which results in the introduction of the waste-heat gases at the top of the front bank of tubes and necessitates the inversion of the usual baffling arrangements. The boilers are equipped with valve-in-the-head soot blowers, which keep most of the dust blown off the surface of the tubes, but it is necessary to supplement the soot blowers by high-pressure air lances, inserted by an attendant through side doors in the boiler setting. Deposits of coal ash and of dust from the furnace charge accumulate in the flues between the reverberatory furnaces and the boilers and this necessitates cleaning of these connecting flues by hand during the greater part of one of the three 8-hr. shifts during each 24 hr. This cleaning operation requires the opening of clean-out doors, which, of course, has some effect on the yield of steam. Revebberatory Furnace Practice The United Verde furnaces are fired with pulverized coal of sub-bituminous type of which the screen and chemical analyses are given in Table 1.

Jan 1, 1934

Sixteen papers concerned with the technology and utilization of low-rank fossil fuels are presented as the proceedings of the 1973 lignite symposium. This symposium, the seventh in a series of biennial meetings, was cosponsored by the Bureau of Mines and the University of North Dakota.

Jan 1, 1974

Jan 1, 1910

By Emil B. Milosavljevic

The photochemical reactions of cyanide ion induced by light were investigated in the presence or absence of a titanium(IV) oxide semiconductor photocatalyst. The light sources employed were the sun and arrays of either mercury or fluorescent (cool white) lamps. The results obtained verify that cyanide decomposes much faster when TiO2 is present in the solution and that it is first oxidized to cyanate. However, contrary to the previous studies, it is established that cyanide is subsequently further oxidized via nitrite all the way to nitrate irrespective of the light source. As expected, the rates of the oxidation processes decrease with the illumination source utilized in the following order: Hg-lamps > sunlight > fluorescent lamps. As nitrate is a significantly less hazardous contaminant than cyanide, complete photocatalytic oxidation of cyanide to nitrate may be a viable method for decontamination of cyanide wastes. Contrary to previous claims, we find that cyanide is slowly photochemically decomposed even in the absence of TiO2. For example, with the mercury lamps as the light source, in two hours, cyanide concentration decreases to essentially zero; up to 7% was converted to cyanate and the remainder to unidentified products.

Jan 1, 1992

By Y Yang, J Skrypniuk

The Jinfeng mine is Sino Gold's flagship project and is the second largest gold mine in China. Sino Gold Limited (SGL) holds 82 per cent equity in the Sino-Foreign joint venture Sino Guizhou Jinfeng Mining Limited (SGJML) with a Chinese partner. Jinfeng is located in a relatively remote site in southwestern Guizhou province. The orebody is considered to be the largest known Carlin type deposit in China. Jinfeng Plant has the world's third largest BIOX« bacterial oxidation facilities (790 t/d), treating highly refractory concentrate generated from crushing, semi-autogenous grinding (SAG) and ball milling and bulk sulfide flotation operations. The Jinfeng Plant construction started in February 2005, commissioning was completed in April 2007, and commercial gold production was achieved in September 2007. This paper describes the successful operations of Jinfeng Plant over the last two years. The key events of the project development are described, from the project background and process design, through to the commissioning and achieving design mill throughput of 3600 t/d resulting 180 000 ounces of gold per year. Process aspects of the BIOX« and carbon-in-leach (CIL) operations over the last two years are discussed which illustrate a very high BIOX« oxidation rate (more that 97 per cent) and excellent CIL recovery (more than 96 per cent). The management of the Jinfeng plant CIL tailings detoxification and filtration is described, and Jinfeng has became the first BIOX« processing plant to have achieved dry stacking of detoxified and pressure filtered CIL tailings. Current efforts to recover cyanide from CIL detoxified solution and the achievement of a zero discharge site water balance are also introduced. Many improvement projects have been made over the last two years which have culminated in a 15 per cent increase in mill throughput over the design and BIOX« CIL recovery increasing from 92.5 per cent to 96 per cent. Significant operating cost reductions from lowered of acid, lime and cyanide usage through process modifications and technical innovations are discussed.

Jan 1, 2009

By David Miller

Longwall gateroad support can be supplied by a variety of methods. The system of support also needs to be flexible as conditions change. This is especially true in the complex geological conditions of the west Kentucky # 13 seam. Methods of gateroad support used in this seam will be presented along with the successes and failures of the systems as conditions changed Lodestar Energy's gateroad support progression through the seven longwall panels retreated to date will provide an insight into planning for future panels

Jan 1, 1998

By Forrest T. Moyer

Injury experience at coal mines and mechanical-cleaning plants (excluding officeworkers ) in 1967 was 222 fatal and 10,115 nonfatal disabling work injuries during an exposure time of 241.8 million man-hours. These injuries occurred at a frequency rate of 42-75 per million man-hours worked; the severity rate was 7,699 days lost or charged per million man-hours. Each of these general measures of injury experience was lower than similar data recorded for 1966. Employment at 6,885 coal mines and 569 mechanical-cleaning plants, excluding officeworkers, averaged 139,312 men in 1967. The average number of days worked was 220. Coal production totaled 560.8 million short tons, at rates of 2.32 tons per man-hour and 18.32 tons per man-day. A total of 2,779 onsite officeworkers at coal mines and mechanical- cleaning plants worked 5.2 million man-hours in 1967 without a disabling work injury.

Jan 1, 1972

By Rosario Bernaola, Alejandra Díaz, Oscar Flores

Este trabajo tiene como objetivo evaluar el efecto del volumen de contenedor, la fertilización y riego en la fase de preacondicionamiento en vivero del Pinus douglasiana, así como su aplicación metodológica en Acacia Saligna, con el fin de incrementar el porcentaje de supervivencia a seis meses de su establecimiento en campo. El preacondicionamiento presentó efectos principales e interacciones entre el volumen de contenedor y la fertilización en las variables de crecimiento, con excepción de la altura y diámetro; mientras que el diámetro y peso radical presentaron una interacción entre el volumen de contenedor y el riego. La fertilización adicional no fue relevante para la absorción de minerales en contenedores de un litro y bajo condiciones de estrés hídrico. Como resultado, las plantas establecidas en contenedores de cinco litros sin fertilización adicional tuvieron mayores porcentajes de sobrevivencia en campo (>80%). Esta investigación está siendo utilizada para el diseño de estrategias de remediación de suelos degradados por la minería peruana, mediante la fitorremediación.

Sep 20, 2019

By G. W. Grove, E. E. Quenon

"INTRODUCTION During September, October, and November 1946 the Safety Division of the Bureau of Mines, off' the United States Department of the Interior, Pittsburgh, Pa., tested four new types of self-contained breathing apparatus and approved them in accordance with Schedule 13C. Approval was granted with the proviso that certain specifications outlined on the approval plate be made fully effective, and with the understanding that established safe practices in training in the care and use of self-contained breathing apparatus are of major importance.The excellent records made during the past 30 years in the safe use of self-contained breathing apparatus, some of which required the almost continuous wearing of apparatus during several hours daily for days, weeks, or months, may be attributed largely to the Bureau's system of rescue organizations, selection of physically fit rescue workers, effective training, and educational work done in rescue and recovery operations during fires or following disasters and in the care and use of self-contained breathing apparatus. Loss of life during wearing of breathing apparatus was due almost invariably to poorly assembled or otherwise defective apparatus, poor physical condition of the wearer, or insufficient training or some incorrect procedure.The newly developed breathing apparatus are of much simpler design than the conventional type used for the past several years; however, it is just as important to select rescue crews carefully and to train them properly in the care, use, and limitations of the new types of apparatus as for the older long-established types, if anything like safety is to be achieved in using them. The Bureau of Mines considers that 1/2-hour and 3/4-hour self-contained breathing apparatus should be used only as auxiliary equipment in mine rescue and recovery work, and their capabilities and limitations should be well understood by those who wear them."

Jul 1, 1947

By L. D. Smith

"Those who submit competing proposals for projects seek to present senior management with complete and fully supported material that will not fail under questioning. Hopefully, misleading notions and omissions will have been minimized and there will have been testing of the assumptions regarding the economic, social and political environments. A capital project evaluation team can do management and itself a service by including a sound approach to the impact of inflation (and its twin problem, interest) on a project and a great disservice with an inappropriate approach to inflation.InflationHandled deftly, inflation can alter a project evaluation to show almost any result the handler desires. It must be a constant source of frustration for design people and cost estimators to spend weeks perfecting the technical aspects of a project in order to minimize costs, only to have all of their efforts set awash in a sea of financial and economic assumptions that submerge all of the detail. In all of this, inflation is perhaps the largest offender, with inflation criteria often being brought to bear at the last minute, almost as an afterthought. Perhaps this tardiness reflects the difficulty of the subject and the belief that senior management will take its own approach to the problems of inflation. Such a belief is unfair to senior management, for it is entitled to not being misled by omission. It is entitled to the full use of the skills of the evaluating team, including respectable assumptions of the impact of inflation.Working in a consulting context, one has the opportunity to participate in the evaluation of a large number of projects. Reflecting the observation of a wide range of views regarding the subject of inflation, this paper will-address the impact of five different approaches to inflation on the evaluation of a single Canadian mining project."

Jan 1, 1987

By J. L. Wyatt

THE smelting of ilmenite to produce a slag rich in titanium, with pig-iron as a byproduct, introduces new concepts in electric smelting metallurgy. Titanium slags are characterized by low electrical resistance, thereby requiring a different type of electric furnace operation, and power supply sources substantially different from those encountered in normal steel melting and siliceous ore smelting furnaces. This paper describes special apparatus for determining specific electrical resistivity of titanium slags, and reports the values obtained on slags encountered in the process of smelting ilmenite ores. In an induction furnace under conditions approximating normal furnacing operation, 25 general heats and 6 special standardization and comparison heats were run. Results indicate relatively low resistivity. Resistivity depends primarily on slag composition, and, to a lesser degree, on temperature. During the summer of 1947 a cooperative project between the National Lead Co. and the Bureau of Mines was conducted at Boulder City, Nevada, in the Electrometallurgical Laboratories of the Bureau. The project involved smelting of ilmenite ores in electric furnaces, and has been reported in detail.' The author participated as a member of the staff of the National Lead Co. during the entire campaign. One outstanding characteristic of the titaniferous slags, their apparently excellent and variable electrical conductivity, was considered sufficiently important to warrant further study. Although little electric smelting of iron ores has been done in the United States, a certain amount of information is available for comparative purposes. Personal experience in smelting siliceous iron ores in electric furnaces furnished further information for comparison. In general, silicate slags are relatively poor conductors of electricity. Current flow during smelting operations may be maintained through a floating layer of coke on top of the slag bath, or through a bath of molten iron, beneath the slag. Silicate slags are not sufficiently conductive to furnish a path for current passage when normal furnace voltages are used. Experimental smelting of a silicate iron ore was undertaken for comparative purposes. A fluid melt was not obtained until the FeO content was reduced to 15 pct. The resistivity increased as the FeO content decreased, FeO compounds being the most conductive of the various oxides in such a normal slag system. The converse appears to be true in slags containing large percentages of TiO2. It has been found that titanium slags become molten with FeO percentages in excess of 30 pct, and that the conductivity becomes generally better as the FeO con-tent of the slag diminishes. This phenomenon was demonstrated in the furnacing operations at Boulder City. During the initial smelting period furnace electrodes could be held immersed several inches in the slag, with tap selectors set for a no-load voltage of 70 v. As the FeO content decreased, the furnace electrodes would "walk up," until at one point in the process the tips would break the surface and arc on top of the slag. This was undesirable since direct arcing caused losses of important flux additions. The slag compositions under study at that time were such that losses due to surface arcing sometimes caused viscous slags to be formed. Forcing the electrodes into the slag bath by manual control to prevent surface arcing resulted in excessive power input and lack of control. Suitable low voltages were not available. Measurement of the electrical resistivity of titanium slags at various operating temperatures and slag compositions was undertaken. It was believed that this information would be of use in the design of electric furnaces suitable for smelting ilmenite, with voltages, electrode sizes, and electrode spacing adapted specifically to titanium slags.

Jan 1, 1951

By R. C. Gilmore, A. Juganda, Jr. Bogin, S. Saki, S. A. Lolon, J. F. Brune, Jr. Zipf, J. W. Grubb

"Methane-air mixtures form explosive gas zones (EGZs) in underground longwall coal mine gob ventilation systems. Such EGZs have caused a number of fatal mine explosions, including the 2010 disaster at the Upper Big Branch mine, where 29 miners lost their lives. Researchers at the Colorado School of Mines use Computational Fluid Dynamics (CFD) modeling to predict EGZ locations. In this paper, a model of a bleeder-ventilated gob system includes two adjacent panels, an active longwall and a mined-out gob. Boundary conditions for the simulations match statutory ventilation conditions for methane concentrations and air flow rates at common measurement points throughout the mine. The modeling results predict the persistence of EGZs in the gob that may compromise the effectiveness of the bleeder ventilation system. INTRODUCTION Mine operators must maintain statutory air flow and air quality requirements at various locations throughout the mine ventilation network. U.S. regulations generally require mine operators to establish bleeder ventilation systems surrounding longwall gob areas (30 CFR §75.334.) Gilmore et al. (2015) documented that explosive gas zones (EGZs) exist within bleeder-ventilated gobs and may extend into the bleeder entries that must be examined weekly, presenting an immediate fire and explosion hazard to mine examiners. In a project funded by the National Institute for Occupational Safety and Health (NIOSH) under contract 200-2009-31409, researchers at Colorado School of Mines have developed a tool for modeling gob air quality using Computational Fluid Dynamics (CFD). This CFD model is capable of examining a wide range of longwall mine ventilation systems. Marts et al. (2014a, 2015) studied progressively sealed gobs with U-type ventilation and using a back return. Saki et al. (2015) examined the impact of gob ventilation boreholes and face air quantity effects on tailgate methane concentrations. Gilmore et al. (2014) modeled bleeder-ventilated gobs and Gilmore et al. (2015) studied the effects of bleeder regulator settings on EGZ volume and locations in the gob. CFD studies for progressively sealed gobs were generally carried out using 5000 ft (1500 m) panels because the gob atmosphere remains largely unchanged from about 500 m (1,500 ft) inby the face. A modular meshing methodology (Gilmore, 2015) permitted researchers to extend bleeder models to 10,000 ft (3050 m) to include the full extent of bleeder entries. This paper further expands the bleeder CFD model to study the gob atmospheres of two adjacent longwall panels, each 10,200 ft (3100 m) in length, with the active face located 6,700 ft (2040 m) from the startup room."

Jan 1, 2016

By W. R. Bull

This paper examines water-only cyclone performance for the cleaning of fine coal, and the effects of changes in feed flow rate, feed pulp density, and vortex finder diameter. A model is presented for performance simulation which can be used to predict products obtained based on feed washability data.

Jan 1, 1987

By John Ralston, Jona Addai-Mensah, Patience Mpofu

The flocculation and dewatering behaviour of kaolinite (non swelling) and smectite (swelling) clay dispersions has been investigated using hydrolysable metal ions Mn(II) and Ca(II) and anionic polyacrylamide-acrylate copolymer (PAM) at pH 7.5 and 10.5. A pH-dependent, specific metal ion adsorption behaviour, accompanied by a marked reduction in particle zeta potential and slurry shear yield stress, was observed to have a profound influence on the colloid stability of both types of clays. Due to the differences in the cation exchange capacity, the smectite clay dispersion required a higher amount of metal ions than kaolinite dispersion to produce similar effects. The adsorption density of the anionic PAM at the negatively charged clay particle surfaces correlated well with metal ion hydrolysis and adsorption behaviour, all of which had a strong effect on slurry settling rate and extent of consolidation. At pH 7.5 where Mn(II) ions hydrolyse, metal ion and flocculant adsorption densities were both greater in the presence of Mn(II) than Ca(II) ions. At pH 10.5, however, where Ca(II) ions begins to hydrolyse, higher adsorption densities were observed for Ca(II) ions in comparison with Mn(II) ions, as the latter hydrolysed completely and precipitated. The metal ion mediated flocculant adsorption led to improved hydrogen bond driven particle bridging and facilitated charge neutralisation flocculation mechanisms which significantly enhanced the dewaterability of both clay dispersions.

Jan 1, 2003

By Daniel de la Rosa, Juan Manuel Mayoral, Damián Vital

"This paper presents a numerical study regarding the loads, and the corresponding damage, taken by the primary and secondary lining of a tunnel built in cemented fine-grained stiff soils. This study aims at establishing more rational design criteria that take into account explicity the lining performance. A 3.5 km long tunnel to be built in a densely populated northwest area of Mexico City, was considered as case study. Series of three-dimensional finite difference models, developed with FLAC3D, were used to simulate the tunnel construction, and to compute the ground settlements, internal forces, bending moments, and displacements acting both on the primary and secondary tunnel linings. Interaction diagrams were used to study the lining performance. Several advancement lengths, and tunnel covers were considered to establish their impact on the loads transferred to the tunnel lining. A practice-oriented damage criterion for tunnels was proposed based on the interaction diagram analysis. INTRODUCTION Lining performance during conventional tunnelling, CT, as defined by the International Tunnel Association, ITA (ITA 2009) is strongly affected by the construction procedure. Special attention must be taken in cemented fine-grained materials, such as those found in the northeast portion of Mexico City, due to the potential of fragile failure (i.e. the soil fails suddenly without important deformation) that these soils may exhibit. During CT, it is assumed that the ground strength contributes to the stability of the excavation, as long as the lining is built correctly. It is common practice to consider two structures, which together form the tunnel support: 1) A primary lining, which is a flexible support, which allows excavation walls to deform to mobilize part of its shear strength, and thus contributes to the tunnel self-stability, and 2) A secondary lining. Commonly, the primary lining consists of several layers of shotcrete. In this case the installation method guarantees perfect contact between the lining and the excavation perimeter. The secondary lining, if required, is used to withstand the load conditions in the long term and also has an esthetic function. This paper presents a numerical study aimed at establishing a performance damage criterion for the primary and secondary lining design in cemented fine-grained stiff soils. Due to the lack of data, the strength and deformation parameters were established through empirically-derived relationships. Three-dimensional finite difference models were developed to simulate the tunnel construction, and compute ground settlements, internal forces, bending moments and displacements acting both on the primary and secondary tunnel linings. Interaction diagrams, along with a damage criterion were used to study the lining performance. From the results gathered insight was gained regarding tunnel lining performance during CT."

Jan 1, 2016

By P. L. Sibrell

Electrorefining of Ti in nonaqueous solvents has been studied by the U.S. Bureau of mines as a method for recycling impure scrap Ti. Electrochemical behavior of Ti species was investigated using cyclic voltammetry. Research results showed that Ti metal can be dissolved in polar solvents such as dimethylformamide or dimethyl sulfoxide. However, deposition of Ti from these solvents was not successful. Several solvent systems were investigated for electrodeposition of Ti but no deposits were obtained. Reduction of Ti4+ complexes to Ti3+ proved to be straightforward, but reduction to lower oxidation states could not be confirmed. In dimethylformamide solutions, cyclic voltammetry results demonstrated the reduction of Ti to an oxidation state of less than three, but no Ti metal was identified. In dimethyl sulfoxide solutions containing LiCl, it was possible to deposit Li metal. After adding Ti salts to the solution, electrolysis quickly passivated the electrode. Deposition of Ti was also investigated in solutions of dimethoxyethane and propylene carbonate but, again, no reduction of Ti to oxidation states of less than three occurred. Therefore, the prospects for a nonaqueous electrorefining system for Ti metal do not appear promising.

Jan 1, 2010

By D F. S Natusch, R J. Hooper

Recent lignite investigations indicate their potential as a strategic long-term fuel resource. This potential however would be determined not only by lignite quantity and quality, but also by economic, physical and social resources required to support it. The following discussion uses the example of a typical lignite mining operation to review the major resource requirements. While recognising that the implications of supplying those resources may be as important as their actual existence, this paper has purposely omitted such discussion as this will be one of the main target areas for the next phase of investigations.

Jan 1, 1983

By F. Brost

In 1976, a decision was made to install a conveying system to transport ore 10.3 km (6.4 miles) from the new Eisenhower Partnership Mine to Twin Buttes. The system, supplied and installed by Cable Belt Limited, of England, represents a radical departure from conventional conveyor systems. The driving tension is applied through two endless wire ropes while the belt acts only as the carrying medium. Features of the system are a single 2240 kw (3000 hp) drive and a 60° angle bend. Construction was completed in two years. Full production was attained after several months' operation.

Jan 1, 1979

Author's Note: Since the paper on "All-Flotation at North Broken Hill Limited" was read and discussed, the metallurgical results obtained have conclusively justified the adoption of the All-Flotation treatment.At present the shipping grades of lead concentrate produced from North mine ore range between 74% and 75% Pb, carrying approximately 43 oz. Ag and 4.5%-5% Zn. The lead recovery in lead concentrate is recording 95%-96% of the lead content of crude ore, and the milling and treatment cost on 6400 tons crude ore perweek of 96 hours has dropped to 6s. 3.6d. per ton on ore. With an increased ore tonnage, and with a new mill, considerable further reduction in costs is certain.New flotation machines, with 30 in. vertical depth of overflow (instead of 42 in. depth), are now being tried for the secondary granular treatment, with advantageous results. The treatment to-day is practically the same as that outlined in the paper, excepting that additional concentrate is returned for retreatment in the existing units.(Signed) A. LOWRY.Mr. T. A. READ: The author states (page 356 of Proceedings, No. 79), "The sulphide ore itself was then comparatively coarsegrained, a fact which permitted ready concentration of the galena contents by means of jigs, tables, vanners, etc."

Jan 1, 1931

By Swati Mohanty

Spiral concentrator, which works on the principle of gravity separation, is widely used in the mineral industries for separation of solid particles based on the size and density. In the present study, CFD simulation of the flow profile on a laboratory scale spiral concentrator of height 2.29 m, pitch 0.435 m and width 0.17m was carried out. A single computational domain covering the entire spiral was considered. Volume-of-Fluid algorithm was used to track the interface and predict the flow profile. In the present study the Donor-Acceptor method was used for the calculation of volume fraction in the cell. Simulation results show that the velocity increases as the water flows down due to the convective force and gravitational force, but the viscous force acting in the opposite direction retards the flow. Thus the maximum velocity is attained at turn three at which the viscous force overpowers the other forces and further down the velocity decreases. Measured water depths along the radius of the spiral at various heights were compared with simulated depths, which were in good agreement. The simulated liquid phase velocity profile was used to carry out preliminary studies on the flow profile of solid particles of size 500 micron and densities 2600kg/m3 and 5100kg/m3, based on the Lagrangian model taking into consideration fluid-particle interaction.

Sep 1, 2012