Search Documents

By Z. T. Bieniawski, R. K. Zipf

"Zipf Jr., R.K. and Bieniawski; Z.T., 1989. A fundamental study of respirable dust generation in coal. Min. Sci. Technol., 9: 87-99Black lung disease in coal miners induced by the formation of fine fragments of coal imposes very high human and direct costs. A fundamental understanding of the fracture processes leading to fine-fragment formation in coal by applying principles of fracture mechanics is presented. A four-step hypothesis is proposed which sequentially describes the mechanics of fine-fragment formation during a generic coal material—coal cutting tool interaction. These steps include: (1) development of a crush zone under the tool tip, (2) macrocrack propagation. (3) shear movement along macrocracks, and (4) additional fragmentation from shear. This model contains two sources of fine fragments, namely crushing under the tool tip and shearing along the macrocrack surfaces. Three critical assumptions are made that require experimentation. First, the coal material must contain flaws of sufficient density and sufficiently small size to liberate fine fragments by crushing. The following conceptual relationships are proposed between flaw size, spacing and fragmentation: first, the active flaw size must be less than the desired particle size and second, the spacing (or density) must be in the order of the particle size. The second major assumption is that a mixed mode fracture theory will describe the initiation and crack growth direction for the microscopic inherent flaws. The third assumption is that some degree of roughness damage, and interlocking exist along the newly formed macrocrack surfaces such that a small amount of shear movement along that surface leads to additional particle formation at a microscopic scale. Preliminary analysis of the mechanical regime under a cutting tool tip places order of magnitude bounds on the stresses strains, cycle time, stress rates and strain rates. Even though the tool moves and loads the coal material with considerable speed, a quasi-static stress analysis is applicable in this region.Introduction.The generation of fine fragments (respirable dust) during various coal mining processes may lead to the incidence of coal workers pneumoconiosis (black lung disease). The human and direct cost of dust-induced illnesses in coal miners is very large. By several. accounts [1,2] the Federal Government paid out about $12 billion to almost 500,000 coal miners and their beneficiaries between 1970 and 1980. In addition, several states and many coal operators have established their own compensation programs at costs ranging from a few cents to several dollars per ton of coal mined [2]. Since 1980, 'the present liability of the Federal disability trust fund has approached $20 billion and the benefit payments exceed $1 billion per year. There .are also hidden costs due to dust, in the form of increased equipment wear and decreased operator productivity, both of which are due to the poor operating environment. Quantifying these costs may be difficult; however, they may be in the same range as the present pneumoconiosis costs. These high human and direct dollar costs may be prevented or reduced through long term research efforts directed at understanding the generation and control of respirable dust and the incidence of black lung disease."

Jan 1, 1989

By D Jensen, L Riffo, S Yu, F Traczyk, D Meadows

With the steady increase of molybdenum demand worldwide and the favorable molybdenum market, many technological innovations on both process and equipment have been developed and applied in many modern molybdenum plants around the world. This paper introduces the most commonly used molybdenum flotation flowsheet, together with the introduction of the flotation chemistry. Many different types of flotation cells are used in modern moly plants, and each type of flotation cell has its own unique advantages suited for particular ore and process conditions. This paper tries to provide some insight and guidelines in flowsheet development and flotation cell selection in the molybdenum plants.CITATION:Meadows, D, Jensen, D, Traczyk, F, Yu, S and Riffo, L, 2013. Molybdenum flotation circuit and flotation cells, in Proceedings MetPlant 2013 , pp 387-398 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Sebastien Flament

More and more Hot Strip Mills are facing defects on their products that lead to a rejection of complete product batches by their customers. Several of those defects are induced by excessive work roll degradation. This paper is focussed on the understanding of work roll corrosion and oxidation mechanisms in a hot strip mill. Several laboratory trials (Hot rolling simulator, cyclic oxidation) have highlighted important factors influencing corrosion of work rolls as well as helping the understandings of oxidation of a work roll in the roll bite and along the roll circumference in a stand. The attention is focussed on several elements present in water used in HSM for direct roll cooling (e.g. chloride, bactericides, sulphates, phosphates) and their effect on roll surface degradation. The second part of this paper is focused on the understanding of work roll oxidation along the roll circumference. The effects of roll composition, roll temperature, water composition and water temperature have been studied in order to understand the oxidation/corrosion mechanisms in a HSM.

Aug 16, 2017

By S Taylor, B Lumsden, G Long

Statistical metallurgical plant trials are becoming more widespread, as a valuable tool for increasing plant profitability. Generally, a single parameter like metal recovery varies under the trial condition while all other variables such as average metal feed grade or average metal concentrate grade are equal for the two test conditions during the period of the test. Metal recovery is usually the measured variable because concentrate grade is fixed by smelter terms, and plants operate to maximise recovery at the required concentrate grade. However, in all flotation plants there is a relationship between concentrate grade and metal recovery, and under the same conditions increasing one results in a decrease in the other. At MMGÆs Rosebery Mine the zinc concentrate produced is generally above smelter specifications, so zinc concentrate grade can vary during a test. During trialling of magnetic conditioning in the Rosebery zinc circuit, the difference in both zinc recovery and zinc concentrate grade were analysed. The analysis of changes in zinc grade and recovery during the trial raised some interesting questions about the relationship between concentrate grade and recovery. A paired statistical method was developed and tested to combine in each pair the change in concentrate grade and recovery in a single result that could be analysed by a paired t test. This method was found to be very sensitive to combined, varying changes in concentrate grade and/or metal recovery. It was also evaluated on plant test results from another flotation plant to verify its applicability in other plants. CITATION:Long, G, Taylor, S and Lumsden, B, 2012. Statistical plant trials - Efficiently combining concentrate grade and metal recovery results, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 355-362 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By Stephen C. Tadolini

The U.S. Bureau of Mines has developed ultrasonic measurement instrumentation capable of measuring strains and elongations on tensioned and untensioned mine roof bolting systems. This report evaluates the pulsed-phase-lock-loop and pulse-echo systems. The pulse-echo systems measure time of flight of a signal through the bolt. The ultrasonic instrument converts the measurement into elongations or stress. The most recent Bureau instrument development converts travel-time measurements directly into elongation, load, stress, and torque by simple data manipulation from the keyboard. Bolt preparation and instrument calibration are described in detail.

Jan 1, 1990

By F. Djahanguiri

The U.S. Bureau of Mines is conducting research on underground stope leaching of metalliferous ores to minimize the environmental impact of ore processing on the surface and to maximize minable reserves. An aspect of this research is to minimize pregnant solution losses and/or groundwater contamination by leach solutions. Bulkhead design and construction are important issues for solution control and stope leaching economics. A reinforced concrete bulkhead was designed, constructed, and tested for solution control in an underground mine near Idaho Springs, CO. This paper presents the bulkhead design methodology and construction procedure.

Jan 1, 1995

By S Hayton

While coal seam gas is considered to be an unconventional gas, the proliferation of areas under exploration and development mean that it is rapidly becoming main stream. The potential of New Zealand's coals to produce coal seam gas has been recognised for some time. However, key market drivers have not been suitable for the progression of this potential into reality. Kenham Holdings Ltd and CRL Energy Ltd, recognising the potential for the gas in New Zealand have initiated what is the largest ever assessment of New Zealand's coal seam gas potential. The premature demise of the giant Maui field has raised the focus of new gas developments and has increased interest in what we are doing. Over the past couple of years Kenham Holdings Ltd and CRL Energy Ltd have approached the assessment of the coal seam gas potential in a staged programme. Preliminary assessment of the data on the permit areas indicates that the potential resource may be up to 500 PJ. To date, preliminary appraisals have been completed or are underway on a significant number of fields. Exploratory drilling has been completed or initiated on several of those fields, with results from this work being fed into the preliminary modelling as it has become available. Given that in many of these areas there is no pre-existing information concerning their gas potential and world wide experience with lignite is practically nonexistent, it has been a steep learning curve with many surprises. However, initial gas content results and preliminary gas flow models have been on the whole, rather pleasing, with the commerciality of some developments already apparent.

Jan 1, 2003

By D. A. Karvonen

In 1970, the Government of Saskatchewan instituted a program aimed at resolving the dilemma of excess productive capacity over the market demand which existed for potash produced in Saskatchewan. The two primary elements of the program were prorationing of potash production to market demand and a minimum selling price. The paper reviews the factors, both local and international in nature that led to the introduction of the program. The licensing mechanics and the operation of the program, along with the changes that have been introduced in two and one-half years of operation, are discussed. Attention is given to the results of the controls as they affect the industry and the province. Also discussed is the outlook for Saskatchewan potash in world markets.

Jan 1, 1973

By V. Brabie, S. Jansson, L. Bohlin

The rate of dissolution of solid MgO-C and doloma into liquid in CaO-Al2O3-SiO2-MgO slag at different temperatures was studied under conditions of forced convection by rotating cylindrical refractory specimens in a stationary crucible containing the molten slag. The corrosion rate was calculated from the change in diameter of the cylindrical specimens. Refractory specimens were 13 mm in diameter and 70 mm long. The specimens were rotated for15 to 120 minutes at speeds of 100 to 400 rpm in the molten slag. The rate of corrosion increased with temperature and with the rotating speed of the rod, and decreased when the slag was nearly saturated with MgO. The experimental results confirm the assumption that the diffusion of magnesium oxide through the slag phase boundary layer controls the corrosion process. The corrosion mechanism seems to be the dissolution of the refractory materials into the slag, followed by penetration of pores and grain boundaries and dispersion of the grains in the slag. Keywords: MgO-C refractory, doloma refractory, molten slag, corrosion rate, corrosion mechanism

Jan 1, 2004

By David C. Byrne

From an engineering perspective an ideal industrial noise control solution focuses directly on the actual source of the poise. Eliminating the noise-generating mechanism altogether obviates the need for other noise contra l treatments or hearing protection devices. However, in cases where attenuating the source is not feasible engineering controls must be oriented toward blocking the path that the sound waves travel toward employees. Acoustical enclosures are commonly used as sound path treatments to contain the noise from a machine: alternatively a control room/booth or equipment operator's cab may be used to isolate the worker from the noise. Anyone who has successfully used acoustical enclosures knows that the design procurement, and installation process is deceptively simple. Alt too often First-time efforts fait to account for many of the constraints that can render the enclosure essentially useless. Things that cannot be overlooked include: providing convenient worker access (physical and visual): allowing for proper machine operation/product flow; and supplying fresh air or preventing undue heat or contaminate build-up inside the enclosure. All of these factors must be given careful consideration, otherwise the enclosure will not perform adequately.

By Becerra J. O

HYL developed a direct reduction process (DR) that does not require a reformer; it is called self-reforming process. Typically, direct reduction processes based on natural gas utilise a reformer unit to transform the natural gas into reducing agents (hydrogen and carbon monoxide). The reforming reactions are: CH4+H20-?3H2+CO CH4 + CO2 - 2H2 + 2CO These reforming units require a catalyst agent to promote the kinetics of the reforming reactions. The catalyst for these reactions is typically a metallic element such as nickel in a ceramic matrix; iron is also an excellent catalyst for the reforming reactions.

Jan 1, 1999

By E. D. Gardner

This paper discusses small-scale lade gold mining and milling. It is abstracted from a bulletin being prepared by the United States Bureau of Mines entitled "Equipping, Developing, and Operating Small Gold Mines." Gold is widely distributed in the mountainous regions of the United States; relatively few deposits, however, can be profitably worked on a large scale. Because of the high intrinsic value of gold, ores containing this metal may be very rich; hence it is possible to mine profitably smaller bodies of gold ore than of the more common metals.

Jan 1, 1934

By d&apos, L. Berenbaum, F. Heurle, R. Rosenberg

The structure of aluminum films obtained by evaporation was studied by electron microscopy, mostly by replica techniques and X-ray diffraction. The resistivities and stress conditions of the films were also determined. Film properties were studied as a function of source selection, substrate type, residual pressures of oxygen and water vapor, substrate temperature, and rate of growth. The formation of abnormal localized growths and whiskers resulting from annealing treatment subsequent to deposition was investigated. Films deposited onto single-crystal substrates were found to be epitaxially 0riented; for such films, relative orientations between films and substrates were determined. ALTHOUGH wide use has been made of evaporated aluminum films for the formation of conducting lines on semiconductor devices, relatively little has been reported concerning the structural characteristics of such films.1"9 The purpose of this study was to obtain an overall view of the dependence of these characteristics on film deposition and subsequent annealing conditions, which were similar to those used in silicon planar technology. Accordingly, most of this study was carried out using oxidized and bare silicon wafers as substrates, although some work was also done using alkali halide, magnesium oxide, and mica substrates. However, the main concern remained pragmatic. Emphasis was given to the study of the effects of deposition and annealing conditions on film characteristics such as structure, resistivity, and stress. I) EXPERIMENTAL PROCEDURES The films which were investigated in this study were deposited in 18-in.-diam glass chambers which were connected to the usual type of trapped diffusion pumps filled with silicon oil. Through the use of liquid-nitrogen-cooled Meisner traps and titanium sublimation pumps placed inside the deposition chambers, the pressure could be lowered to the lower portion of the 10- I Torr range and little increase in pressure would occur during the deposition cycle. Unless described otherwise, the substrates were 1-in.-diam p-type silicon wafers having a resistivity of 10 ohm-cm. The wafers were oxidized in wet oxygen at 975°C followed by a short dry-oxygen exposure at the same tempertture to a total oxide thickness of approximately 6000A. The wafers, backed by a layer of gallium, were mounted onto molybdenum discs brazed to a copper block.10 The latter was heated by imbedded commercial cartridge heaters. The substrate temperature could be maintained to within +10°C of a prescribed temperature during film deposition. The search for a satisfactory source for the controlled evaporation of aluminum has led to the use of 1-in.-diam crucibles" machined from rods of a commercially available, refractory composite* of Bn and

Jan 1, 1969

THE nature of the ore deposit of the Broken Hill line of lode is such that it can be broadly divided into two the calcitic and siliceous ore bodies. The principal minerals occurring in these ores are: Galena, sphalerite, pyrite, arsenopyrite, chalcopyrite, pyrrhotite, calcite, rhodonite, garnets, feldspar, fluospar, quartz.Whilst these minerals persist in both classes of ore, the following typical analyses of Broken Hill South Limited ore bodies will give some indication of the disposition with regard to each:

Jan 1, 1928

By G. Sachs, E. J. Riping

All ferrous alloys can be made brittle by straining at sufficiently low temperatures. However, the changes in mechanical properties for different ferrous materials with decreasing testing temperature do not appear to follow any universal law. In particular, complex effects of testing temperature have been observed if cold worked steels were subjected to tensile tests at low temperatures. EFFECTS OF PRESTRAINING AT A TEMPERATURE ABOVE THE TESTING TEMPERATURE ON THE FRACTURE CHARACTERISTICS‡ A considerable amount of data has been presented by a number of investigators on the fracture characteristics of various cold worked steels.' These data usually relate to a two-step procedure first used by Davidenkov,² consisting of stretching by tension to a certain strain or " prestraining" at room temperature and then completing the tensile test, or "testing" at the temperature of liquid air. On the basis of data of this type made available to date, ferrous alloys can be classified into two groups with respect to their fracture characteristics observed on testing at a low temperature after prestraining at room temperature. Very complex phenomena have been observed for all annealed steels. On the other hand, some observations indicate that steels in certain other conditions represent a fundamentally simpler relation. In considering the effect of prestraining at one temperature on the properties obtained at some lower temperature, it should be expected that any cold work reduces the ductility retained in proportion to the magnitude of the cold work. However, the test data presented to date indicate that only heat treated (quenched and tempered) steels appear to conform to this expectation, according to the very limited test data in Fig 1, presented by McAdam, Geil and Mebs. This series of tests, Fig 1, shows that the retained ductility became smaller the larger the prestrain. However, this decrease is less than the amount of prestrain or, in other words, less than the decrease in ductility at the prestraining temperature. These effects of prestraining are fundamentally identical with those observed by Bridgman3 when a steel was prestrained (in tension) under hydrostatic pressure and then subjected to a regular tension test. It appears, therefore, that the basic effect of prestraining under conditions which yield a higher ductility than the (subsequent) testing procedure, consists of gradually increasing the total ductility of the metal from the initial low value of testing to the higher value of prestraining. On the other hand, all annealed steels, if cold worked by tension at room temperature and then tested at a lower temperature, provided that some ductility is retained, showed a far more complex behavior than that discussed above. This relationship is exemplified by Fig 2, for three pearlitic steels.4,5 These particular steels were selected because of the various shapes of their ductility-prestrain curves. All three steels, and any other investigated so far, suffered a rapid decrease in retained (and consequently also in total) ductility when subjected to small pre-strains. Then, after exceeding a certain prestrain it was generally observed that the ductility recovered.* This rather complex behavior of annealed steels may be tentatively correlated with the presence of stretcher strains at small restrains. Heat treated steels do not exhibit stretcher strains. This fact might possibly explain their simpler prestrain-retained ductility relationship. The destructive effect of these stretcher strains may possibly be associated with the presence of triaxiality, which may occur in any highly non-uniform stress and strain state (and which is retained as residual stress after unloading). Even a small degree of triaxiality may then cause a reduction in ductility, or even embrittlement at a sufficiently low testing temperature. The discussion presented above deals with the effects of cold working at a high temperature on the fracturing

Jan 1, 1950

By Wesley T. Holmes

This report describes the second phase of an investigation aimed at obtaining a wider knowledge of the problems involved in smelting titaniferous magnetites. Liquidus temperature measurements were made on selected synthetic slag compositions in the Ti02 -A1203 -FeO-Si02 -CaO-MgO system. Both the hot-stage microscope and the strip furnace (melting-holding-quenching technique) were used during test procedure to determine the effects of CaO, MgO, and SiO2 on the liquidus temperature of slags. The liquidus temperatures of slags studied ranged from 1,241° to 1,900° C. The lowest liquidus temperature for each Ti02 plus A1203 plus FeO weight-percent generally occurred when the difference between CaO plus MgO and Si02 was less than 12 weight-percent. In this investigation substitution of either CaO or MgO for SiO2 and MgO for CaO raised the liquidus temperature of more than 50 percent of the reported base slags when Ti02, A1203, and FeO contents were held constant. The results of this investigation may serve as guidelines for determining flux requirements in smelting a wide variety of titaniferous magnetite concentrates or ores.

Jan 1, 1968

There is an alternative theory of the high grade orebodies of the Middleback Group, based on the primary nature of the high grade ores in an area of carbonate deposition, with lesser amounts of siliceous and aluminous sediments. The environment is thought to have been unstable, possibly volcanic, and to have been a subsiding basin, substantially isolated from the open sea.Jaspilites, iron bearing talc rocks and iron bearing carbonate rocks were derived from the primary sediments by metasomatic alteration after metamorphism.The metasomatic agents were carbon dioxide and water vapour which were mobilized from the primary dolomite and reacted with a metamorphically produced group of iron bearing and iron free amphiboles, forming talc and progressively releasing silica and iron oxides from the iron amphiboles.The talc rocks in turn released silica which reconstituted jaspilites into their present 200 ft thick crust or zone.The theory accounts for the present disposition of a jaspilite zone over a talc zone which in turn overlies a carbonate zone, and accounts for the down dip changes found in bores which penetrate these zones.INTRODUCTIONIron Duke (Fig. 1) lies some 34 miles south west of WhyalIa in South Australia, and is the most southerly ore body in the Middleback Ranges.The Middleback Ranges are divided into a northern range and a southern range meridionally disposed and separated by an erosion gap called Kimba Gap.The South Middleback Range contains four orebodies;Iron Duke at the southern extremity, Iron Duchess north of Iron Duke and on the same ridge, Iron Knight also on the same ridge, which has been breached by erosion between theDuchess and Knight orebodies, and north east of Iron Knight, the Iron Chieftain.Cook's Range is the eastern range of the South Middleback Range and no large orebodies are known to occur there.

Jan 1, 1963

By A. B. Young

T HE smelting industry in Utah is represented by four plants: The Midvale of the United States Smelting, Refining & Mini.ng Co., the Murray of the American Smelting and Refining Co., the Garfield of the same company and the Tooele of the Inter- na.tiona1 Smelting Co. The first two are lead smelters, the Garfield plant is a copper smelter while the last named embraces both a lead and copper smelter. A total daily smelting capacity of over 10,000 tons is represented, of which 4000 tons is lead smelting capacity. With the exception of Tooele, forty miles distant, all of these smelters are within twenty miles of Salt Lake City. Pyrometallurgical operations in this district are con- fined entirely to the production of unrefined bullion, which is shipped east to the various refineries of the respective companies. The smelting industry in this state had its beginning away back in the latter days of the Civil War, many years before the completion of the trans-continental railroad. Ox teams were still bringing their companies of better fixed Mormon emigrants across the plains to the valley of the Great Salt Lake and those in lesser circumstances were still pushing their hand- carts over the same roads to the temporary abode

Jan 1, 1925

By G. E. McElroy

THOUGH air jets occupy only a minor role in the ventilation of mines and other enclosures, their importance in this respect is greater than is commonly recognized and may be considerably increased as our conception of their modes of operation becomes clearer. The object of this paper is to discuss some of the ways in which air jets are involved in mine ventilation and some possible applications to the ventilation of mines and other enclosed spaces. The mention of air jets ordinarily suggests the use of some form of an air injector, such as the Venturi blower occasionally used for auxiliary ventilation in mines, or the Saccardo (injector) system used to a limited extent for ventilating railroad tunnels. Actually, the term covers such common phenomena as the discharge of air from fan pipes and coal-mine line brattices, and even from smoke stacks and fans. A knowledge of the general mode of air entrainment by jets also helps to explain certain phenomena-some mine-gas explosions, for instance-that otherwise would remain obscure. Jet action has been involved in three recent series of Bureau of Mines experiments in which the author has participated: experiments on fan-pipe discharge, on the dilution of gases discharged from a stack and on the ventilation of a ship's hold. Available data on the discharge of jets into large openings and on the design and performance of air injectors have been analyzed in considerable detail and supplementary experiments are planned for after the war. The results of the fan-pipe experiments have been combined with the analyses of data on jet discharge into large spaces, and have been published.1 The results of the stack-gas dilution tests, which refer to a jet discharged into a crosswind, have also been published2 and a paper on the design and performance of injectors has been prepared for publication.3 These technical experiments and analyses form the background and the documented evidence for the following nontechnical discussion of the use of air jets in mine ventilation. JET CHARACTERISTICS The jets commonly encountered are those in which the air is in turbulent-as opposed to laminar, or streamline-motion. The characteristics under discussion apply only to such turbulent jets and have their basis in theories of the mixing of turbulent air currents. Such jets have basic characteristics that are present, though variable in form, regardless of whether the jet expands freely in space, whether the expansion is limited by adjacent walls, or whether the jet propels air through a flow circuit. They expand at definite angles and entrain the surrounding air, even though the entrained air must be obtained by recirculation of their own air streams. As the quantity of air in motion in the mixed stream increases, the average velocity of the stream decreases. In the case of entrainment in the free

Jan 1, 1945

Owing to circumstances which are entirely unavoidable, the cost of rendering to Institute Members the services which they have been ac-customed to expect from the Institute has increased enormously, especi-ally during the past year. The cost of printing has increased 20 per cent. and another 30 per cent. is expected. There is no recourse; the Institute must pay this or cease publishing. The increase for supplies and office force will be very great. Justice to our employees, whose cost for living expenses has risen by leaps and bounds, demands an increase in. wages, wholly aside from the fact that the employees need not and will not stay. The Institute is, therefore, faced with the alternative of greatly re-ducing its service to the members or else of asking from them a small increase in clues. An amendment to the Constitution has been offered by the members increasing the clues to $15 per year, which cannot become effective until 1921. This still leaves us as the engineering society with the lowest annual clues, except only one, whose dues are $15 per year. To help meet the immediate emergency, the Directors have exercised the authority vested in them by the Constitution and By-Laws and requested the members to pay $3.00 for the Transactions to be issued during the year 1920, which is very much less than the cost of publication. It is the opinion of the Board that the members will prefer to pay this slightly additional expense rather than to have the Institute take a backward step in respect to the services which it is rendering, and which has been increasing constantly in amount, as well as in unit cost, during the past seven or eight years.

Jan 12, 1919