Search Documents

By J. A. Organiscak

Enclosed cabs are a primary means of reducing the silica dust exposure of equipment operators at surface mines. The National Institute for Occupational Safety and Health (NIOSH) has investigated various factor effects on enclosed cab air filtration system performance. Factors experimen­tally investigated were intake filter efficiency, intake air leakage, intake filter loading (filter flow resistance), recirculation filter use and wind velocity effects on cab penetra­tion (inside to outside cab concentration ratio). Adding an intake pressurizer fan to the filtration system was also investigated. Results indicate that the intake filter efficiency and recirculation filter were the two most influential factors on cab penetration. Use of a recirculation filter significantly reduced cab penetration over the intake air filter by itself due to the multiplicable filtration of the cab interior air. Cab penetration was also affected to a lesser extent by intake filter loading and air leakage. Adding an intake pressurizer fan notably increased intake airflow and cab pressure while providing only minor changes to cab penetration.

Jan 1, 2008

By M. J. Kovalik, D. E. Wolfson, F. Fischler

Plastometric tests were made to determine the maximum thickness of the plastic layer for different U.S. coals . The effect of test variables on the maximum thickness of the plastic layer was studied . The values for the maximum thickness of the plastic layer were found to be related to the Gieseler maximum fluidity , plastic temperature range , free swelling index , and other plastic properties of coals . Only a general relationship was observed between the plastometric parameters obtained in these tests and the coking properties of coal .

Jan 1, 1964

By C. W. Huggins

The primary objective of this Bureau of Mines research was to measure the size distribution of respirable quartz collected at metal mines, nonmetal mines, and processing plants to select the best reference standard for use in quantifying quartz in mine and plant dust samples. The secondary objective was to size all the nonquartz particles collected at the same sites. Particle size measurements were made on 29 samples using a scanning electron microscope in the backscatter mode of operation, interfaced with an image analysis system. The Mine Safety and Health Administration, Denver, CO, provided the 29 samples, which were collected at mines and processing plants in 19 states. The accumulated particle size measurements indicate that NBS 1878, minus 5-f.lm Hin-U-Sil, and minus 5-f.lm Supersil would be preferred over Silver Bond B as reference standards for most quantitative determinations by X-ray diffraction and infrared spectrometry. The respirable dust samples collected at sand plants, however, would be better served by a new reference standard having a quartz particle size distribution of approximately 2.2 um, as none of the four existing reference standards matched closely with them. Commercially available NBS 1878 and minus 5-um Hin-U-Sil CQuid be used as reference standards for 28 of the 29 samples studied in this investigation.

Jan 1, 1986

By Jeffery L. Kohler

The research and development of a pattern recognition system which can predict incipient failures and safety hazards in the mine power network is described. An examination of mine electrical safety hazards revealed they are often related to the electrical equipment down-time experienced on mine sections. Based on this, a method is proposed that can improve both production and safety, without compromising either. Equipment failure modes are examined to illustrate how the ultimate failure can be predicted for enough in advance to allow a convenient and safe repair, followed by a discussion of actual monitoring system performance. Finally, the paper is concluded by projections of the system's utility to industry.

Jan 1, 1977

By M. A. Trevits, G. W. Luxbacher, L. D. Patts

"It is almost a given that post-disaster mine conditions will have compromised the mine ventilation system, resulting in a hazardous atmosphere in portions of the mine, and often complicated travel through debris fields and roof falls. Robotic technologies provide the opportunity to gather valuable information to assist decision making or lessen exposure to dangerous conditions. MSHA's Mine Emergency Operations Division (MEO) has utilized a fully permissible mine robot, the V2, for a number of years, constantly updating the unit as new technologies became available. The National Institute for Occupational Safety and Health, as part of the MINER Act Extramural Contract Program, examined the need for additional robotic units and ultimately funded three different types of prototype technologies: two robots, the Snake Robot and the Gemini-Scout, and a mine rescue robotic assist vehicle known as the ""Mule"". The Snake Robot is designed to be lowered through a borehole and to conduct surveillance (gas monitoring, video and audio) in the immediate vicinity, while the Gemini-Scout, designed to be deployed in the mine opening, serves as a more mobile and agile exploratory tool as compared to the MSHA V2 robot. The Mule was developed in response to needs expressed by mine rescue teams for a versatile remotely operated support vehicle and it will move from prototype to MEO utilization in the near future. This paper describes the development of the robot prototypes and discusses their limitations in the prototype stage, possible enhancements and potential applications, as well as the utilization of the Mule. INTRODUCTION The conditions in a coal mine may be dramatically altered after a mine fire or explosion. For example, the ventilation system may not be functioning correctly as control devices may be compromised or damaged beyond repair. The visibility in the mine opening may be limited due to accumulated smoke and dust. Roof support systems may be damaged or no longer functional. Equipment and materials may be strewn about the mine opening. Debris fields, blocked openings, roof falls, flooded areas, gas accumulations and active burning make it very difficult or impossible for those managing the post-event emergency to permit mine rescue teams to enter the mine to conduct search and rescue operations. With the evolution of robots and robotic assist technology there has been a proliferation of purpose-built units for the military, police and law enforcement agencies, urban search and rescue and those contending with hazardous environmental conditions. In each case, the technology used is designed to limit human exposure to the unsafe conditions or to provide access to areas under difficult conditions. For example, a specially-designed marine robot has been deployed into the damaged core of the Japan’s Fukushima Daiichi Nuclear Power Plant to assess the conditions of the containment vessels, where melted fuel is believed to have accumulated. Human access to the area is prohibited due to dangerously elevated levels of radioactivity [1]. Multiple robots were deployed in Amatrice, Italy, to assist in the response after the 6.2-magnitude earthquake devastated the town. The robots were used to explore two medieval churches that were severely damaged and deemed too dangerous for human entry [2]. Tactical robots are regularly used by police and law enforcement agencies when the conditions of the emergency place intervening officers directly in harm's way [3]."

Jan 1, 2018

By G. J. Birnie

Introduction The preparation of the following paper has been undertaken in the belief that a description of the development methods and equipment used at Lake Shore, at the present time, will prove of general ? interest. Working depths of nearly a mile and a half in shaft sinking and of more than one mile for stoping operations have imposed problems not encountered at shallower horizons. Among the problems contributing to the difficulty of mining at extreme depths might be mentioned: Rock pressures Ventilation Hoisting Shorter work period at the face Geological considerations In the main, the effects of these factors add to the difficulty of mining at depth, but it is not entirely true to say that each must necessarily become more pronounced as mining operations proceed to greater depths. Corrective measures may, in some cases, retard the effect and in others may even relieve some of the difficulty. It is proposed here to discuss these features in the light of the experience at Lake Shore, and to present, in some detail, the current practice in shaft sinking and in driving ore and waste passes, raises, drifts and cross-cuts.

Jan 1, 1950

By M. Barsky, E. Barsky

It is generally accepted that the optimal flow velocity for gravity classification is the final particle settling velocity or, which is the same, the particle spin velocity. However, we have found differences between the settling velocities and the spin velocities of the very same particles. Here we present the results of experiments in a cascading gravitational classifier comprising eleven stages. The feed material was introduced at each stage successively, from the first to the eleventh. The optimal flow velocity was determined for each case. From these experiments it follows that the value of the optimal flow velocity depends to a greater extent on the point of introduction of the feed (i.e., on the design of the device) than it does on the interaction between the solid phase and the flow.

Jan 1, 2003

By W. D. Mcmillan

Kaolin, or china clay, is the term applied to a group of hydrous aluminum silicates. Because of its purity, light color, and refractory properties, kaolin is used extensively in the manufacture of high-grade ceramic wares and as a filler by the rubber and paper industries. Although there are numerous pottery and enamelware plants in Texas, and large rubber and paper industries; all of the kaolin used in these plants is from other States, There are two known occurrences of kaolin in Texas, namely, the Leakey deposit in Real County and the several deposits of the Medley district in southern Jeff Davis County. An investigation of the Mueller kaolin deposit in the Medley district was undertaken by the Bureau of Mines. Following an examination of this deposit by W. D. McMillan, engineer in charge of the Texas field office of the Bureau of Mines, a proposal was made to investigate the deposit by diamond core drilling.

Jan 1, 1949

By Ross W. Smith

Microorganisms are increasingly finding use in mineral processing and hydrometallurgy both for the enhancement of mineral engineering operations and for the remediation of mineral industry wastes. Some of the applications, such as biologically assisted leaching of sulfide ores and biooxidation of refractory sulfide gold ores, are established commercial processes. Others, such as the use of organisms for the removal of heavy metal ions from dilute aqueous streams, are nearing commercial application. Other uses of microorganisms are potentially possible. These include use of microorganisms in leaching non-sulfide ores, the flocculation or flotation of minerals and remediation of toxic chemicals discharged from mineral engineering operations.

Jan 1, 1993

By J. M. Whatley

"IntroductionIN UNDERGROUND mining operations, the mine hoist has become one of the most important and one of the most expensive single pieces of equipment. As the means of transporting men and materials to the face, broken ore to the mill, and waste to the dump, it is often the very lifeline of a mine and must operate with dependability and efficiency or the whole operation will suffer. The mine hoist has become synonymous with safety. In few other types of mechanical equipment do so many men so frequently and completely place their lives. In Canada, more has probably been done to assure safe hoisting than in most other countries, but, unfortunately, this has resulted, in many cases, in the mines having to pay a high price for equipment. Hoist manufacturers have carried out much research in recent years in the endeavour to keep down these costs and at the same time maintain or improve the efficiency and safety of their products. Broadly classified, the bases for design research are dependability, efficiency, safety, and first cost.Probably the greatest single factor influencing the design of mine hoists was the introduction of electric motor drives. It was not until about 1905 that an effective start was made in the development of electric mine hoists, and then only with machines of small size. From that time on, however, progress was rapid, as may be gauged from the fact that by 1910 one large group of mines in Johannesburg had in use, or on order, fifty-four three-phase hoists and four Ward-Leonard. type hoists."

Jan 1, 1953

By Patrick McElhinney, Jacob Carr, Bruce Whisner, Cory DeGennaro, Jingcheng Li

Since 2016, electromagnetic interference (EMI) of personal dust monitors (PDMs) with magnetic proximity detection systems (PDSs) has been observed in underground coal mines. The EMI causes the magnetic field measurements of a PDS to change, which, in turn, alters the calculated location of the miner relative to the machine. Any altered location calculation can potentially cause the PDS to fail to warn a worker who is at an unsafe distance from the machine, arousing a serious concern on safety hazard caused by EMI in underground mines. The search for EMI mitigation strategies led to the development and use of large shielding pouches and boxes to hold the entire PDM to reduce its magnetic emission. Research on these pouches and boxes found that although they were able to reduce the emitted radiation from the PDM, they also disturbed the magnetic field of the PDS, affecting its performance. Researchers from the National Institute for Occupational Safety and Health (NIOSH) have focused on shielding internal PDM components rather than shielding the entire PDM. The PDM air pump motor is one of the PDM components that has been identified as a major source of electromagnetic radiation and has been selected for further study and tests. The measurements show that a small copper or aluminum foil enclosure can effectively reduce the magnetic emission of the motor by between 50 and 85% at 73 kHz. This study compares the test results of the air pump motor with various cost-effective shielding materials. The data provided in this paper can serve as a reference for shielding enclosure design of the PDM air pump motor to reduce its electromagnetic emission as one form of EMI mitigation strategy.

By Rodney Hundermark, July Ndlovu, Lloyd Nelson, Phillimon Mukumbe, Paul van Manen, Whitey Seyanund, Bart Pieterse, Bertus de Villiers, Diale Mokwena

The 2003 redoubling in power to 68MW on the Polokwane Smelter furnace represented a significant intensification in platinum group metal (PGM) smelting. Combined with onerous ‘green’ PGM concentrate smelting requirements, this yielded conditions unusually corrosive to copper coolers and refractories. This presented unexpected operational and design challenges to reliable crucible operation and maintenance. Combined with specific operational control intervention, development of protective coatings has led to the life of water-cooled copper components improving from 9 to 40 months. The furnace matte endwall was extended in 2010 to address accelerated wear of refractories and the potential risk for contact of copper components by superheated matte. An 18 month planned endwall rebuild cycle has been demonstrated (versus catastrophic failure within 9 months). Finally, benefits including lower energy consumption, improved metal recoveries and higher productivity resulting from operational and in-house design developments will be described, that justify “Celebrating the Mega-scale” in PGM smelting.

Jan 1, 2014

By JAMES QATLEY

THE atmosphere, which plays such an important part in the manufacture of iron and steel, is the most variable element involved in its several processes; and particularly is this true of the blast-furnace process, which consumes air in large quantities. At no time since the blast-furnace became an important and widely used apparatus-even when it was operated in the most crude manner-have the variations in composition of the raw materials used been as frequent and as great as the variations in humility of the atmosphere. Important, improvements have been made in the blast furnace and its accessories, such as the hot-blast stoves, the increase in size and change in the shape of the furnace, more efficient blowing engines, the increased protection given to the bosh walls, and the careful preparation of' the raw material, all of which have exerted a pronounced influence on the furnace-operations from a metallurgical standpoint. But during the past eight years little advance has been made in this direction; the fuel-consumption has not diminished, nor has there been any material increase in production. Within that period, however, there has been witnessed the greatest development in appliances for the economical handling of material. So complete has been the work in this direction, that, except in isolated cases, in this country at least., a further extension does not hold out much promise of a satisfactory return on the investment required. It seemed that, with the exception of the gas-engine, we had about reached the limit, for like a strong wall, the atmosphere, with its humility as variable to-clay as when first blown into a primitive blast-furnace, appeared to stand as a Barrier to

Jan 1, 1905

By AIME AIME

THE Petroleum Division will hold two meetings this fall, one on the Coast at Los Angeles, Sept. 29, with the technical sessions in the assembly room of the California Oil and Gas Association and a banquet Friday evening at the Richfield Cafe atop the Richfield building; the other in the Southwest, at Dallas, Texas, Oct. 6 and 7, with the Baker Hotel as headquarters. Dr. Frederick M. Becket, President of the Institute, and A. B. Parsons, Secretary, will attend both meetings. Arrangements for the meetings are not yet complete but the respective local committees, working in close touch with the officials of the Division are rapidly shaping up the programs and other detail.

Jan 1, 1933

By D Chalmers

"There is a tendency to treat mine roadways with fan installations as leak proof systems. Morecomplex ventilation arrangements are being installed in coal mines out of necessity or designand these can introduce additional hazards. This paper explores the leakage paths that can existaround fans and in particular the hazards these leakage paths may generate around undergroundfan installations. The behaviour or these leakage paths in the event of a fan failure has also beenexplored. Early detection of spontaneous combustion is essential, so understanding the leakage behaviour around fans especially boosters or main fans installed underground will assist in sett ing up monitoring locations in the correct places. If this behaviour is not fully understood then monitoring may be placed incorrectly, or trends may not be picked up until it is too late."

Jun 1, 2012

By A. Gakwaya, K. Ba, M. Guillot, J. Levesque

"In the aerospace industry, parts requiring tight dimensional tolerances and high mechanical properties are often produced by forging. This forming process allows for an optimal use of the material and can produce high quality parts at a reasonable cost. Thanks to CAD techniques, it is now easier to predict flow profiles and in-process defects occurrence as well as wear of the forging dies. However, in order to determine the properties of the forged part with computer simulation methods, a good material constitutive law is a prerequisite. This paper presents a virtual manufacturing process modeling for the closed die forging of a workpiece performed with Abaqus. The hot closed die forging is a regular process applied to manufacture metallic components used in aerospace industry. In this forming process, the material flow and final properties depend on the microstructure evolution during the process that is why it is important to include the microstructure effects in the material model. Based on the stress-strain data measured experimentally, the material parameters of the standard (classical) Johnson-Cook constitutive model and of a modified Johnson-Cook constitutive law including the microstructure effects have been determined. The obtained simulation results are compared with the experimental results for validation.INTRODUCTIONDue to their good physical and mechanical properties such as ductility, fatigue strength, corrosion resistance and rupture, aluminium alloys are often used in the aeronautic and the automobile industries. In this work, we present the forging of an Al-Zn-Mg-Cu alloy, a high strength aerospace alloy recognized for his good combination of physical and mechanical properties. The forging process is simulated in Abaqus Explicit using both the standard Johnson-Cook law (Johnson & Cook, 1983; Hor, 2011; Lin et al., 2012), and its modified version as proposed by Andrade et al., (1994). The Johnson-Cook law offers the advantage of considering the coupled effect of the plastic strain, the plastic strain rate, the temperature of forging and the hardening effect. However, it is a phenomenological model which does not account for the effect of the microstructure evolution. In this work, a modified Johnson-Cook model implemented in a user subroutine is used. It includes the effect of the dynamic recrystallization phenomenon during the hot deformation. The dynamic recrystallization has a noticeable influence on the microstructure and on the properties of the material. The term dynamic means that the process starts and acts during the deformation and this is different from the static mechanism of recrystallization which occurs during an annealing and after cold or hot deformation. Since properties of the alloy used in this work are not readily available in the literature then characterization tests have been done at various temperatures and strain rates, in order to determine the thermomechanical properties and the material behavior during the process of hot forming, more precisely during the hot forging process."

Jan 1, 2016

By M. W. Von Bernewitz

The Bureau of Mines receives frequent requests for information on the treatment of mercury ores, but as its own and almost all other publications on mercury are out of print, the Bureau has prepared this circular on the metal for the prospector and operator of small mines and plants. Mercury, commonly though improperly termed ?quicksilver?, is the only common metal that is liquid at ordinary temperatures. Mercury is used in the amalgamation of gold and silver, in power boilers, explosives, friction-less bearings, laboratory apparatus, lamps, medicine, paint, rectifiers, and for ?silvering.? The last mentioned is being superseded by silvering with silver. The use of mercury boilers may increase when they are thoroughly understood, but amalgamation is -being replaced to some extent by the use of corduroy and other collecting mediums, such as jigs and flotation cells.

Jan 1, 1937

By G. G. Huggins

A demonstration project has been completed to reduce the operator sound level of an underground service vehicle, a personnel dispatch wagon, to go dB(A) or less. The program objective was to implement quieting recommendations made on an earlier study for the USBM n diesel-powered mine equipment. The manufacturer and mine to which the vehicle was going actively participated in the program to ensure a product that was not only quiet, but useful. The key element of the quieting package is an engine part a1 enclosure, which, with several complementary noise control components, reduced the operator sound level 14 dB, from 101 dB(A) to 87 dB(A). The vehicle underwent a 4-month trial period, with no degradation in the quieting package. Mine personnel reported no maintenance difficulties, and were enthusiastic about the dispatch.

Jan 1, 1975

By M. C. Irani

This study is a survey of supply and demand for minerals, metals, alloys, and compounds used by the chemical industries in the Ohio River Basin (ORB) area of Ohio, Pennsylvania, and West Virginia during 1967. Data for the study were obtained from completed questionnaires received from chemical manufacturers and from interviews with officials of chemical companies and mineral producers and distributors. The information includes kind, quality, quantity, values, sources, specifications, uses, and methods of transportation. Results of the study show that of the total value of mineral materials consumed by the chemical industry, manufacture of inorganic chemicals consumed 46 percent; fertilizers, 22 percent; and soaps and detergents, 19 percent. Fifteen commodities accounted for 91 percent of the total value of mineral materials consumed. Five of these--phosphates, potash, salt, sulfur, and titanium dioxide--accounted for 59 percent of the total.

Jan 1, 1970

"Qatar, crude petroleum, production, annualdata MY 1949-51Quality mine, Ark., coal, carbonizing properties TP 667washabilty study RI 496N. Dak., lignite, grindabilty as function ofmoisture, tests, results RI 5167"

Jan 1, 1960