Search Documents

By A. J. Van Rensburg, N. B. Strydom, C. H. Van Graan

The design, construction, and use of a practical ice-jacket for miners by N. B. STRYDOM, Ph.D. (Illinois) (Fellow), D. MITCHELL, Ph.D. (Rand) (Member), A. J. VAN RENSBURG, M.Sc (Poteh) (Visitor), and C. H. VAN GRAAN, M.Sc (Pretoria) (Visitor) Microclimate suits have been shown to be very effective in decreasing physiological strain in hot, wet environments, thus enabling men to work without risk in areas that would normally carry a high risk of heat stroke. In this paper, some design considerations in the development of the frozen jacket are described. Water complied with most of the desirable properties required of a coolant material for use In a microclimate suit. The Human Sciences Laboratory has developed a jacket in which ice is used as the coolant and which is designed according to the most acceptable anthropometrical characteristics. The jacket consists of an inner poncho-type waistcoat containing 28 water compartments. Over this is worn an insulating jacket, which minimizes warming of the coolant by the environment. Suitable refrigeration units have been developed to freeze the jackets underground. Laboratory tests have shown that these jackets are effective for about 2,5 hours, Irrespective of the wet-bulb environment, when men are working at a moderate rate. Jackets should, however, be used only in environments in which the wet-bulb temperature is in the range of 32,S0 to 35,S °C.

Jan 9, 1974

By W. E. Wallace, P. S. Raghootama, M. S. Seehra, C. A. Hill, M. J. Keane, P. Mike

"Dipalmitoyl glycerophosphorylcholine (lecithin) dispersed in physiologic saline, a model of the primary component of pulmonary surfactant, is adsorbed by respirable quartz and aluminosilicate dusts. Dust cytotoxicity as measured by erythrocyte hemolysis and pulmonary macrophage enzyme release is suppressed by this adsorption. The degree of suppression of hemolytic potential versus specific adsorption of lecithin from dispersion in saline by respirable quartz, kaolin, and alumina dusts are compared with dusts' BET specific surface areas to interpret the prophylactic effect cf lecithin adsorption. Dust hemolytic potential versus media pH are presented. Fourier transform infrared spectroscopy and photoacoustic spectroscopy of lecithin on quartz and of lecithin on kaolin are presented and reviewed with results of studies of the time course of removal of lecithin adsorbed on mineral surfaces by digestion by phospholipase enzyme. Results are discussed in terms of a model of prompt neutralization of respired mineral dusts by pulmonary surfactant, and a gradual re-toxification by digestive processes acting on the adsorbed prophylactic surfactant coating following phagocytosis.Introduction Quarts dust of respirable size is well known to cause fibrotic lung disease, but numerous questions persist in the understanding of the initiation and' progression of this disease. Our approach concentrates on physical and chemical aspects of mineral dusts early-on in their interactions with living organisms, and we have chosen simplified models to investigate that interaction. In the alveolar spaces of the lung, tissue is coated with a surface-active material (pulmonary surfactant), which, sagas other functions, mechanically stabilises the lung from collapse by reducing the surface tension of water in the alveolar sacs.(1) This surfactant is also the material that is first contacted by a mineral particle that is transported to an alveolus and is impacted there. This surfactant material has been studied extensively. The primary components are known to be proteins (about 11% in dog lavage fluid). and phospholipids (about 88%).(2) Fhosphatidyl cholines constitute roughly 80% of the phospholipid fraction; about 70% of the phosphatidyl choline fraction is dipalaitoyl lecithin (DPL).(2) Respirable aluminosilicate particles are capable of adsorbing dipalmitoyl lecithin from dispersion in physiologic saline, a model for a possible initial event occuring upon deposition of a particle in a pulmonary alveolus.(3)"

Jan 1, 1988

By E. Grygiel, J. Haynes, T. McNider

Jim Walter Resources Blue Creek No. 3 Mine was opened in one of the most gassy coal beds in the United States. Although face ventilation requirements exceeded 14,000 cfm (6 .6m3/s) air, continuous miner sections experienced an unacceptable frequency of frictional ignitions. Modifications offered primarily by the U. S. Bureau of Mines such as diffuser fans, water spray fans, and slow speed cutting motors were used with little success. However, laboratory tests conducted at the U. S. Bureau of Mines indicated that an increase in bit attack angle from 50° to 55°-57° significantly reduced the chances of the bit causing a frictional ignition. An experimental miner drum was built using this concept coupled with a new bit designed by the Bureau and manufactured by Hughes Tool Company that better protected the bit steel shank with a carbide cap. It was installed on a continuous miner and placed in an area of the mine prone to ignitions. 50,000 tons (45,500 metric tons) of coal were cut without a frictional ignition. When the miner was withdrawn for rebuild and a machine with an unmodified cutting drum placed in service, two ignitions occurred before 10,000 tons (9,100 metric tons) were mined. Other machines have been rebuilt and are in service, and to date none have been known to cause an ignition.

Jan 1, 1987

By Brian Lewis, Reinhold Daykin Schnell

Blasting is the primary and most effective method for breaking and moving material at most mine sites. The blast design is often adjusted in efforts to optimize the effectiveness of the blasts’ explosive energy while minimizing costs. When adjusting blast design parameters, it is important to adjust one parameter at a time, observing and analyzing the potential effects of the change on the overall blast performance.

Feb 6, 2023

By S. G. McDowell

Automation techniques are used during the design stage of continuous miners to decrease the time required and ensure the accuracy of the design. This is followed by automated manufacturing processes to reduce manufacturing time and improve the quality and consistency of parts. Combined, the result is a more reliable machine that can provide ongoing production capability. With the use of automation to enhance operator effectiveness and monitor machine condition, the productivity of machines is also improved. Productivity of continuous miners doubled over a 10-year span (Fig. 1). Although this article focuses on the continuous miner, it should be recognized that production increases of the continuous miner would not be realized without increased capabilities throughout the rest of the mining system. There are several aspects of automation that have played a role in providing increased continuous miner productivity. Though some are considered indirect, they still had significant influence on the overall result. Basically, productivity increases are obtained by cutting, loading and transporting the coal at a maximum rate. In addition, these tasks must be consistent, with minimal downtime. Therefore, the miner had to improve in operational capability and reliability. Automation techniques used during machine design, manufacturing and operation have all played significant roles in achieving higher productivity.

Jan 1, 1991

By R. Stanevich

Studies by the National Institute for Occupational Safety and Health (NIOSH) and the Bureau of Mines (BOM) have demonstrated that: (1) 90% of diesel particulate is less than one (1) micrometer in aerodynamic diameter; (2) more than 90% of the respirable mass in electric coal mines was greater than one (1) micrometer in aerodynamic diameter; and (3) in coal mines using diesel equipment, average diesel concentrations can represent up to 53% of the MRE respirable coal dust standard. For mines approaching the 2 mg/m3 standard, compliance may be easier to attain by controls directed at diesel exhaust particulate as opposed to coal dust control. First, however, a Simple instrument is needed to measure diesel exhaust particulate concentrations. This paper describes such a sampler, its construction, and use. While results from this sampler are primarily utilized to identify control areas, NIOSH is also using the sampler for estimating worker exposures in epidemiologic studies.

Jan 1, 1988

By L. C. Brichta

The Tri-State zinc-lead catalog, compilation of which was initiated by the Bureau of Mines in August 1949, is designed to provide a continuing record of avail-able drill-hole logs and maps of mine developments in the zinc-lead district in southwestern Missouri, southeastern Kansas, and northeastern Oklahoma. The maps and data thus preserved constitute a reservoir of factual information readily available to individuals and firms interested in planning mineral explorations, to Government agencies for formulating estimates or ore reserves, and to the mining industry in the district for general uses. The areas to be included in the catalog embrace the explored and mined tracts within 760,000 acres of the more active western part of the district. The consensus among local mine operators, geologists, and mining engineers is that over 100,000 boles, costing more than $30,000,000, have been drilled in the district. Records of some of the early drilling and mine developments are destroyed or lost, but the Bureau of Mines has copies of about 47,500 drill-hole logs and is accumulating and recording on microfilm those that are currently available. As of May 1, 1954, the logs of approximately 28,000 drill holes had been microfilmed and are available for inspection at the Bureau of Mines office, Joplin, Mo.

Jan 1, 1955

By John W. Fredland

Many accidents occur in the mining industry as a result of the instability of material during handling and processing operations. Accidents due to dump point instability at stockpiles, and at spoil or waste piles, for example, occur with alarming frequency. Miners must be trained to be better aware of these hazards. Information on safe working procedures at stockpiles and surge piles is provided. Mine operators must review their training and operating procedures regularly to ensure that hazardous conditions are avoided.

Jan 1, 1993

By P. W. Udo Graefe

"An interactive computer model of a dragline, windrow and spoil pile has been developed for modelling oil sands mining operations. The model is to be used in conj unction with models of other oil sands mining equipment, such as bucket-wheel excavators and reclaimers, conveyors, hoppers, bins, trucks and shovels, to study mining operations on a minute-by-minute basis. From the orebody description and mining selectivity, layers of ore and reject are determined and mined by the dragline. Reject is dumped on the pit floor; ore is either dumped on a windrow for later removal by a bucket-wheel reclaimer or directly dumped into a hopper feeding a conveyor. The model allows for the presence of pads as a dragline base, key cuts and a number of interruptions to the mining operation such as shift changes, boom checks, engineering services, repairs, delays, preventative maintenance, etc. A CRT display keeps the model operator informed about equipment status and performance. The model operator can direct the course of the simulation by issuing commands to the model at any time during the simulation.IntroductionThis paper describes an interactive computer model of a dragline, windrow and spoil pile. The model was designed by the author based on information and specifications provided by Canstar Oil Sands Ltd. The model design was implemented and tested on Petro-Canda's IBM computer system by DMR and Associates Ltd. of Calgary, Alberta.The model was designed to form three components of an oil sands mining operations model, described in reference I. Figure 1 shows the interaction of those components with the remainder of the oil sands mining model.An ""Ore/Waste Body"" data base provides information to the dragline model about the location and composition of or e and waste in the mine. The dragline model is used to simulate mining this ore/waste body, to build up spoil piles for center reject (waste) and to dump ore onto windrows or hoppers (situated over conveyors) to deliver the ore to the extraction plant. The windrow model component provides a data base which will be used by a model of a bucket-wheel reclaimer which simulates the loading of ore from the windrow on to a conveyor via a bridge."

Jan 1, 1982

By William Pitman

Ground instability and subsequent rock falls are a major concern in underground mines. As a result, several mining companies are conducting risk assessments of the ground support installed in their mines. Risk assessment is now commonly used to provide mine operators with a systematic process to assess the strategic risks that could lead to injury to personnel or loss of production, and evaluate possible risk control measures. Risk assessments can be carried out to identify major hazards, assess the likelihood of occurrence and consequences of each hazard and estimate the level of risk. This process allows assessment of possible remediation actions to minimize the risk and likelihood of occurrence or mitigation of the consequences to a level that is reasonable and practical. This paper presents two practical mine applications of qualitative risk assessment of ground support to highlight the benefits of this process. Yearly or bi-yearly risk assessment of mine excavations can assist mine operators in prioritizing resources and areas that require support remediation. In addition, it provides a mechanism for proactive response to reduce potential risks associated with personnel safety, equipment safety and environmental impact. It also provides a baseline against which changes in ground condition can be compared and quantified.

May 1, 2004

By M. Ito

The authors have developed the RETAC jig (a modified TACUB jig) and have reported that the RETAC jig can separate relatively low density particles such as plastics. To further improve the separation ability, a hybrid jig (a RETAC jig with an air bubbler under the particle bed), which can separate plastics having similar specific gravities by the differences in the wettabilities of the particles was developed. Surface modification of plastics with similar wettability enabling separation in the hybrid jig and the effects of wettability control of the plastics using reagents are reported.

Sep 1, 2012

By Thomas M. Barczak, David P. Conover

Longwall shields provide essential ground control in longwall mining, yet a high percentage of shields are operating at less than peak capacity and many at well below the rated support capacity due to defective hydraulic cylinders or malfunctions in other hydraulic components. Leg pressure data are currently collected on state-of-the-art longwall shields, but typically are not analyzed to evaluate shield performance. The National Institute for Occupational Safety and Health (NIOSH) Shield Hydraulics Inspection and Evaluation of Leg Data (SHIELD) program is a Visual Basic software system that is designed to analyze leg pressure data and identify shields that are not performing to rated specifications. The program analysis is configured to detect the following conditions: (1) loss of leg pressure, (2) imbalance in leg pressure, (3) low set pressure, (4) low yield pressure, and (5) full extension of the bottom stage. Other performance assessment measures include the percentage of the support capacity utilized (ratio of peak load to yield load), the percent of time that a shield operates at yield load, the ratio of the set load to the yield load, and the amount of support capacity that is lost due to leaking cylinders. Historical record keeping will allow the user to select a particular shield and review the performance record as developed by the program for that shield. In addition to these performance assessment measures, the software will include an animated description of shield hydraulic systems that will describe the operation and significance of each hydraulic component and the impact of component failures on the shield’s capability to provide the required roof support. A general overview of the SHIELD program is provided in the paper together with an example analysis of a 2.5-year-old Australian longwall face.

By Jinsheng Chen, S. S. Peng

The relationship between support performance parameters and parameters representative of mining and roof conditions is characterised by uncertainty, non-linearity and dependence, so the theory of artificial neural networks was selected as a basis for shield design. A computer program based on a back-propagation training algorithm was written to derive the weighting factors between inputs and outputs from field data; once these had been established two mathematical models were developed to describe the relationship. Back-calculation of field data indicates that the results generated from the neural network models are much more accurate than those derived by traditional methods and can be used with a higher level of confidence. The support density, possible yield frequency of face supports and interval of periodic roof weighting under specific mining and roof conditions can be determined by application of the models

Jun 21, 1905

By Gerald Verbeek, Erick Baziw

Stone columns are used in geotechnical site remediation to increase load-bearing capacity and reduce settlement of foundations. Stone columns also improve slope stability and increase the shear strength of a soil. A very challenging problem is to characterize the in-situ shear wave velocities from data acquired from Downhole Seismic Testing (DST) after the insertion of stone columns. DST is an important geotechnical testing tool for site characterization that provides low strain (<10-5) in-situ interval compression and shear wave velocity estimates, but the postanalysis of seismic data acquired from DST in the presence of stone columns is very challenging due to the resulting complicated in-situ soil conditions. To obtain the right results it is necessary to use an algorithm that incorporates source wave raypath refraction. Starting with the Normal Moveout Seismic Cone Tomographic Testing (NMO-SCTT) algorithm developed some years ago, this paper outlines the modifications and additions made to this NMO-SCTT algorithm to facilitate stone column site characterization. To dramatically reduce the optimal solution space for the estimated interval velocities the paper also described a priori conditions that are applied based on the unique nature of the stone column site conditions.

James DouGlas, New York, N. Y. (communication to the Secretary*):—In my paper on the Conservation of Natural Resources, I referred to the slow replacement of bee-hive ovens by the by-product ovens as a most notable instance of waste. And I quoted from Mr. Parker&apos;s report for 1906 an explanation given by him in accounting for the small production of by-product coke. It was that the market for the by-products of the coke-ovens was so limited that some of the ovens constructed were out of operation. His report on the manufacture of coke in 1908&apos; does not record an improvement, and attributes the strange fact that we alone, of all the industrial peoples, delay the adoption of this cardinal improvement from the continuance of the same almost inexplicable cause. To quote again from his report, he says (p. 241): "The year 1908 was not marked by any notable gain in the construction of byproduct coking plants, though some new work was done. There was a net increase

Jan 1, 1910

By Junya Tokita

In Japan, packaged explosives have traditionally been used as the most common explosive for tunneling. Recently, some blasting systems such as ANFO with a kettle loader and emulsion explosives with a pump loader have been trialed in order to improve safety and efficiency of the charging process. There are issues with these systems relative to the Japanese market. ANFO dissolves in water easily, and generates ammonia gas when it contacts with concrete. Emulsion explosives need costly pump ing unit s, and there is a need to control residuals in the pump unit. Additionally, there are obstacles by Japanese law to site mixing of emulsion explosives.

Jan 1, 2005

By R. G. Garlick, H. B. Probst

Tungsten single-crystal specimens of various orientations were deformed in tension at room temperature. Slip traces indicated both (112)(111) and (110) (111) slip; however, about 10 pct plastic dejormation was required bejore these traces could he seen. Resolzled shear-stress considerations indicated that at least some of the particular systems observed were not those on which slip initiated hut were secondary systems. This is highly probable, considering the high plastic strains involved. Analysis of the stress data with respect to possible slip systems indicated that slip must have been initiated at stresses below the proportional-limit stresses measured. ALTHOUGH there is general agreement that slip deformation in fcc and hep metals takes place on the plane of close packing and in the direction of close packing, there is no such agreement for slip in bcc metals. It is generally agreed that the close-packed direction (111) is the slip direction, but investigations have led to conflicting descriptions of the slip plane. As Hoke and Maddin1 point out, there are essentially four points of view. 1) Deformation in bcc metals is composite shear on (112) and (110) planes or on nonparallel (110) planes, and any apparent slip on other planes can be accounted for completely by slip on these planes. Chen and Maddin have reported this to be the possible case for molybdenum." 2) Slip occurs in the (111) direction and is limited to {110), {112), and (123) planes (the three closest packed planes of the lattice). 3) Slip occurs in a (111) direction, but not necessarily on planes of close packing (banal slip). 4) Slip occurs in those directions and on those planes for which ß, the ratio of Burgers vector to interplanar spacing, is a minimum. The slip systems of the bcc metal tungsten have never been fully determined, although several investigators have reported pertinent results.3"7 The present work was initiated to determine the active slip systems in tungsten at room temperature, the critical resolved shear stresses associ- ated with these systems, and the orientation dependency of operative systems. These features of tungsten deformation at room temperature have never been reported in the literature. The authors find this somewhat surprising, particularly in view of the availability of tungsten single crystals since the advent of electron-beam zone-melting techniques and the widespread interest in refractory metals. It would seem apparent that such work has been attempted but the results have not been reported, possibly due to the conflict with deformation theory. The results of the present work conflict with any straightforward description of deformation based on the proposed explanations of slip in bcc metals. Although these conflicts have not been resolved, a presentation of the problem seems in order and should be of value to others working in this field. MATERIALS AND PROCEDURE Single-crystal tungsten rods of 1/8-in. diameter were grown from undoped commercial rod by one-pass electron-beam zone melting in apparatus previously described by witzke.8 Representative analyses of the rod before and after melting are given in Table I. There was no detectable zoning of impurities during melting. Buttonhead tensile specimens, as shown in Fig. 1, were machined from single crystals. Two flats 90 deg apart were ground in the gage length of each specimen. These flat surfaces facilitated the analysis of slip traces. No attempt was made to position these flats with respect to the crystal orientation. The worked surface layer of the machined specimens was removed by electrolytic polishing in a NaOH solution. Tensile-axis orientations were determined by standard Laue back-reflection techniques. The sharpness of the Laue spots indicated that the crystals were free of strain.

Jan 1, 1964

By Thomas A. Gwynn

"A beautiful America will require the effort of government at every level, of business, and of private groups. Above all it will require the concern and action of individual citizens, alert to danger, determined to improve the quality of their surroundings, resisting blight, demanding and building beauty for themselves and their children." "Improvement of our environment" has become a cause much like "motherhood". The increased awareness of the public concerning this subject makes it most unpopular for anyone to be involved in anything that seemingly is detrimental to our environment. And this awarement goes far beyond our biggest pollution problem in America - the distribution of paper, abandoned automobiles, beer cans and other garbage by our enlightened society along every city, highway, trout stream, river and mountain in America. In fact, the greatest awarement comes because of the "sensational" reporting and writing in our various national communication media, wherein the same voting citizens who so generously distribute their refuse about the countryside are emotionally aroused and duped into transferring what is truly a national problem onto the shoulders of a few industries - notably and particularly the mineral extraction industry. Certainly mankind is more and more stumbling over his own garbage daily, a fact that is easier to sell a citizen of one of our large cities than a resident of the wide open spaces of the west. Yet even in the Rocky Mountain states, the "Land of Sky Blue Waters", the "Big Sky Country", and particularly in Salt Lake valley smog is not unknown. Pollution and littering have become problems that need to be faced squarely. In North Dakota alone it has been estimated that one section of farm land each year flows down the mighty Missouri and the greatest producer of sediment is now reported to be the highway department.

Jan 1, 1969

Amongst representative men directing alluvial mining of erations in Victoria, some difference of opinion exists as to the best system of working the deep leads. The developmental operations of shaft-sinding, extending a reef drive, partially watering and rising up into the wash dirt are practically the same on all fields but subsequent mining is continued either on the Chiltern and Rulberglen or Ballarat systems, the latter being referred to by the Chiltern and Rutherglen miners as the &quot;down country&quot; system. In the former, the leading wash and cross drives are lept from 300 to 500 feet ahead of the reef drive, and in the latter the reverse method keeping the reef drive well ahead of all wash workingsis adopted.In the majority of alluvial mines in the southern and western fields, the initial work of defining the course of the lead is costly, owing to the thick superincumbent layers of hard basalt, to bore which costs from 9/- to 15/&#183; per foot. Unfortunately large sums of money have been wasted in this work, owing to a want of care and knowledge in the selection of bore sites, and improper recording of the strata pierced, thus handicapping alluvial mining and bringing boring operations...

Jan 1, 1902

By J. Waldman, M. B. Bever, A. K. Jena

The heats of formation at 273°K of 6 silver-rich Ag-Cd solid solutions and the heat of formation at 78°K of one solid solution have been measured by tin solution calorimetry. The heats of formation are analyzed in terms of the quasichemical theory. If the enthalpy diffel-ence between a hypothetical fcc form and the hcp form of cadmium is taken into account, this analysis does not lead to the conclusion put forth in the literature that electronic effects make significant contributions to the heats of formation of silver-rich Ag-Cd solid solutions. The temperature dependence of the heats of formation is appreciable and negative near 78ºK, but decreases gradually to nearly zero abore 400°K. The relative partial enthalpies per grarn -atom of silver at 541°K and cadmium at 532" and 541°K in tin have also been determined. THE composition range of the silver-rich Ag-Cd solid solutions stable at room temperature extends to about 40 at. pct Cd. Heats of formation of these solid solutions at 308" and 723°K have been measured by solution calorimetry.1,2 Heats of formation for an average temperature of 800°K have also been calculated from vapor pressures.2,3 The heats of formation deviate from the values predicted by the quasichemical theory above about 30 at. pct Cd. This deviation has been attributed to electronic effects at the Brillouin zone boundaries.2 The heats of formation of Ag-Cd alloys are essentially the same at 308", 723", and 800°K; consequently the temperature dependence of the heat of formation d?H/dT = ?Cp is vanishingly small, although from the exothermic heats of formation a negative value would have been expected. In the investigation reported here the heats of formation at 273°K of 6 silver-rich Ag-Cd solid solutions and the heat of formation at 78°K of 1 solid solution have been measured by tin solution calorimetry. The results are analyzed in terms of the quasichemical theory and the dependence of the heats of formation on temperature is discussed. The relative partial enthalpies per gram-atom of silver in tin at 541" and cadmium in tin at 532" and 541°K were obtained in the course of this investigation. The values of the temperature dependence of the relative partial enthalpies per gram-atom of silver in tin derived from the data reported by various investigators2,4-9 are contradictory. The literature contains only a value for 517°K of the relative partial enthalpy per gram-atom of solid cadmium in tin.2 EXPERIMENTAL PROCEDURES Samples of Ag-Cd solid solutions were prepared by melting weighed amounts of silver (99.99 pct pure) and cadmium (99.95 pct pure) in graphite crucibles under a flux of molten potassium chloride.10 The solidified ingots were sealed in evacuated Vycor tubes and annealed at 775°K for 10 days. The ingots were swaged and drawn into wires. The wires, sealed in evacuated Pyrex tubes, were held at 725°K for 5 hr and cooled to 365°K at an average rate of 2.5ºK per hr, followed by furnace cooling to room temperature. Chemical analysis of samples taken from different parts of each ingot gave no indication of segregation. Metallographic examination showed the samples to be homogeneous. Samples of the solid solutions or of the component elements were added to tin-rich baths in a calorimeter." At the start of a run the bath consisted of pure tin. Silver was used in the form of wire of 0.01-in. diam as supplied and cadmium in the form of lumps. Gold (99.999 pct pure) was added with the samples in order to reduce the endothermic heat effect of additions of Ag-Cd solid solutions. Samples of only one composition were added in a run and the ratio of the weight of alloy to that of gold was the same in all additions of a given run. In each run several calibrating additions of tin were made from 273°K. The heat contents of tin were calculated from the following equation, which is based on published data:12 (HTºK- H279º) = 6.70 T - 72,300/T + 20 cal/gram-atom; 505°K < T < 650°K The heat effect of each addition was plotted against the average of the sum of the atom fractions of solutes in the solution before and after that addition. The total concentration of solutes at the end of a run was less than 2 at. pct. In this range the heat effect was a linear function of the atom fraction of the solutes. The heat effect at infinite dilution and the composition dependence of the heat effect were obtained from the plots. RESULTS AND DISCUSSION Evaluation of Data. The linear dependence on composition of the heat effects of additions suggests that in the dilute range the enthalpy interaction coefficients other than the first-order coefficients of silver, cadmium, and gold are negligible, as shown in a concurrent publication.13 The heat effects at infinite dilution and the values of the composition dependence of the heat effects are listed in Table I.

Jan 1, 1970