Search Documents

By J. L. Gartshore

PRACTICALLY all of Quebec's chrysotile asbestos production derives from twelve mining and milling operations located in the "Eastern Townships" area of the province. The annual output of these twelve operations exceeds one million tons of chrysotile asbestos, valued at over one hundred million dollars, and is shipped to manufacturers spread over all six continental areas of the world. A total of approximately twenty million ton of asbestos ore yearly, or about seventy-five thousand tons a day, is mined. Individually, the operations vary in size from about two thousand tons to thirty thousand tons per day. Removal of waste rock and overburden to develop these ore tonnages varies greatly from one mine to another, but would probably average out at about a one to one ratio.

Jan 1, 1962

By John W. Mentz

Phase I study efforts addressed: 1) acid mine drainage formation theory; 2) effects of inundation in reducing acid mine drainage formation; 3) summary information on the types of acid abatement technology currently available and the problems inherent in each; 4) analysis of two potential means of partially inundating abandoned segments of active underground mines to reduce acid formation. This subsequent Phase II Draft Final Report addresses all of the above, but concentrates on and defines Item 4. Seal construction techniques were taken through five logical steps as follows: A) Location Analysis; B) Coal Barrier Pillar Analysis: C) Ground Water Analysis; D) Design Considerations: E) Economic Analysis. The design details of both low wall dams and section seals were discussed in a series of segments: a) Case Histories; b) Feasibility Analysis; and c) Design (including representative calculations). Study efforts showed that both concepts are feasible only in certain mines where the geologic-hydrologic physical makeup is suitable to contain a mine pool. Low wall dams in particular were found to have extremely limited applicability as a means of pollution reduction. Section seals, while clearly dependent upon site specific conditions, have a some what broader range of utility and are more effective in pollution reduction. The proven dramatic reduction in acid mine drainage attributable to inundation makes this a concept that must be considered.

Jan 1, 1981

By H. Vuthaluru, O. Kavianipour, C. -Z. Li, N. Suresh, D. Sahu

The paper describes a CFD model developed for 76mm Dense Medium Cyclone (DMC) using Ansys Fluent Software to gain insights into the separation of particles according to their size and density. The simulation used in this paper includes the Reynolds stress model to predict the turbulence inside the cyclone body. An Eulerian-Eulerian multiphase CFD model was applied to model a number of physical aspects such as the separation of coal particles and the segregation of magnetite media solids. The experimental results generated in a laboratory scale DMC were used for the validation purpose and the predicted results of CFD have been validated for the flow splits of water, magnetite and coal. The simulation results obtained from the Eulerian-Eulerian multiphase model revealed that the prediction agreed with experimental results, and matched reasonably well in terms of the mass flow rates of water, magnetite and coal. Furthermore, the partition curve of the DMC when mapped for the separation of - 3.0+0.50 mm size also showed to be in agreement with the experimentally obtained curves. The gravity of cut (SG50), also predicted by the Eulerian-Eulerain multiphase CFD model, was found to be in the vicinity of observed experimental value of SG50. Keywords: Dense medium cyclone, Eulerian-Eulerain multi-phase modelling, computational fluid dynamics, cut gravity (SG50)

Jan 1, 2020

By R. E. Phelan

WHILE 1931 was a most important year in the history of Canadian copper smelting and refining, nevertheless, due to the low price of copper and the in- ability of the International Nickel Co. to market its full capacity of nickel. the production of both copper and nickel was considerably less than the total installed capacity for the production of these metals. IIY the nor- mal course of events, 1931 should have seen a great increase in the production. of both copper and nickel in Canada, because the large extensions to both the copper smelting plants and the copper and nickel refinery capacity, which had largely been completed in the year 1930, should be showing their effect.

Jan 1, 1932

By Myron W. Mellor

Much has been published concerning the subject of coal preparation as related to electric power generation however it is always a most vital topic for both utilities and coal producers, It also constitutes a field of study that is never finished since new concepts and changing demands continually require altered perspectives. One graphic illustration that has been used to emphasize the rapidity with which times are changing is the fact that during World War I, a station that consumed 1000 tons per day was looked upon as a large central station, while today some single generators require 1500 tons during the same period, For further emphasis, at that time a 20,000 horsepower turbo-generator was a mighty large machine; today, a unit of this size is planned for driving the boiler water feed pump required for a single large main unit. During the past ten years alone, electric utilities have more than doubled their percentage of coal consumed as compared to the total market. They now account for approximately 40% of the United States consumption and one-third of all production including export, Conversely, approximately 70% of all U. S. steam electric generation is by coal and this percentage is expected to increase. It is further predicted that utility consumption will increase from the current 160,000,000 tons per year to between 400 and 500 million tons in 1975 which is approximately equal to todays total production

Jan 1, 1959

By C. J. Pritchard

As productivity improvements reduced the number of continuous miner sections from seven to three while maintaining full productive capacity, a decision was made to test an advancing tailgate ventilation system on the shortwall mining section. Having the shortwall mine its own return air system has freed the third mining section for more productive, less costly mining. The advancing tailgate has provided effective ventilation across the face and gob with acceptable pressure losses. The tailgate development continuous miner section has been since transformed from a low productivity part-time function to a high productivity development/retreat panel and is available for long term mine development duties also.

Jan 1, 1989

By R. A. Garling

INTRODUCTION Since the infancy of in situ uranium mining, a growing number of hydrometallurgical processes have been incorporated into pilot and commercial scale flowsheets. Although initial design efforts were geared toward maximizing uranium recovery and minimizing plant and wellfield flow circuit maintenance, recent emphasis has shifted to improved means of water conservation and aquifer restoration. As mining units approached depletion, evaporation ponds reached minimum freeboard, and state and federal agencies demanded proof of groundwater restoration, processes including mixed bed and conventional ion exchange, reverse osmosis and electrodialysis were adopted by the industry. These units served the additional function of reducing process bleed flows during mining in states where the deep disposal well permitting ice remains unbroken. This report concerns the use of electrodialysis as an alternative to the more conventional processes used in in situ mining. In addition to a brief history and description of the process, a comparison to reverse osmosis and operational data derived from testing an Ionics, Inc. 1.31 x 10-3 m /s (30,000 gallon/day) unit at the Teton-Nedco Leuenberger Research and Development pilot will be presented. HISTORY Commercially practicable electrodialysis was contingent upon the development of synthetic ion exchange membranes in 1940's. In 1952, Ionics Inc. demonstrated that the process was amenable to the treatment of salt and brackish water and, in 1954, made their first commercial sale. The following decade saw several major electrodialysis unit sales which were generally targeted for use on private or municipal potable water treatment. Major increases in membrane desalting unit capacities, facilitated by technological advances in the reserve osmosis industry, were noted during the 1970's. The development of polarity reversing electrodialysis equipment which reduced feed pretreatment requirements, increased water recovery rates, and simplified unit operation, kept Ionics Inc. competetive in the water treatment industry. Engineering advances which incorporated automated equipment, non-corrosive construction materials, and improved ion exchange membranes allowed the electrodialysis process to compete in industrial waste treatment among other commercial markets. PROCESS AND APPARATUS DESCRIPTION The electrodialysis process utilizes direct electrical current passed across a stack of alternating cation and anion selective membranes in order to achieve an electrochemical separation of ionized materials in an aqueous solution. The membrane stack has the appearance of a plate and frame filter press and auxilliary equipment includes solution pumps, electrically actuated valves, filters, piping and a direct current power source. The ion separation membranes are thin sheets of synthetic cation or anion selective resins. Attaching sulfonate or quaternary ammonium groups to the cross linked copolymer structure determines the ion selectivity of the membrane. The membranes are separated from each other in the stack by non-conductive spacers that house flow channels which route the flow tortuously and parallel to the membranes. Direct electrical current passing perpendicularly to the membranes and solution passages attracts cations toward the cathode and anions toward the anode (Figure 1). As the ions from the feed stream pass through the ion selective membranes, they become concentrated in the adjacent brine channel and are retained there by the combined attractive force of the electrode and the repelling force of the next membrane toward the electrode. Limiting factors on the degree of demineralization possible include chemical solubilities in the brine flow and the current density that will produce an unacceptable degree of polarization (Figure 1). Feed or brine solution treatment with complexing agents or acids has been successfully applied to prevent membrane scaling. Polarization can occur when sufficient current density is applied to dissociate water in the ion depleted region of the diluting compartments near the membrane surfaces. Significant polarization is evidenced by large electrical resistances across cell pairs and notable pH differences between diluting and concentrating streams. Limiting current densities have been increased in U.S. manufactured equipment by utilizing tortuous flow paths of relatively high linear velocities thereby promoting continous solution mixing. Energy consumption is due to separating electrolytes and solutions, oxidation and reduction reactions occurring in electrode compartments, overcoming electrical resistance, conversion from AC to DC power, solution pumping and auxiliary equipment actuation. A major improvement to the basic electrodialysis process was applied in 1970 which resulted in frequent, automatic cleaning and descaling of membrane surfaces. The process, polarity reversal, incorporates alternating the cathode and anode on a periodic basis while exchanging product and brine flow channels via electrically actuated values. The reversal reduces the potential of stack plugging with CaCO3 (calcite), CaSO4 (gypsum), and colloidal materials and, in most waters, eliminates feed pre-treatment requirements. For approximately two minutes during and following the reversal, off spec. water is flushed to waste or reintroduced to the feed supply. The usual feed treatment on polarity reversing electro-

Jan 1, 1982

At an early stage of the examination of most prospects, samples are taken; and the sample values obtained play an important part in determining the subsequent history of the prospect. It is, therefore, important that. eveJJy effort should be made to interpret asfully as possible the meaning of the observed results. In this connection, it is suggested that examination of the assay values of mine samples by simple statistical methods may bring to light information of considerable value, which might otherwise be missed.Although expert statisticians may derive more information from the available data, those who are, like the writer, less proficient mathematically, may also benefit by applying quite simple statistical methods. At least they will develop a useful habit of thought bywhich they become aware at all times that sampling results only provide estimates of the truth, but that an assessment of the precision of such results may be possible. The object of this paper is to provide some evidence of. the truth of these statements, by theuse of a few very elementary statistical calculations.General.The idea that any mine sample is subject to error from a variety of causes is a very familiar one. Doubt always exists with regard to the representativeness of a perfectly cut sample, and other errors may arise through imperfections of sample cutting, crushing, splitting and assaying. Some causes of error may give rise to "constant" errors, others may cause variable but one-sided "systematic" errors, and others again may bring about variable results without any tendency toward bias on the average. In statistical language, mine sample values are subject to errors which may have either assignable causes or chance causes. The former are those which can be isolated, or should be capable of isolation, while the latter are those remaining when all assignable causes have been removed. A single constant assignable cause brings about bias in all results, and one or more than one variable assignable cause brings about variation between individual results and perhaps an overall bias. The system of chance causes that would remain if all assignable causes were removed would cause variation between individual results but no overall bias. There is no sharp practical line of distinction between the two types of cause) of error; nor is it ever possible by any method of statistical analysis to be certain that there are no assign...

Jan 1, 1950

By Otis M. Clarke

Although most bauxite mined is used to make metallic alu¬minum, more than a million tons of bauxite is used annually in the United States in the manufacture of refractories, chemicals, abrasives, and cement. Raw material requirements are becoming increasingly difficult to meet because high-grade bauxite, required for some uses, is limited. The supply of raw material for high-alumina refractories is most critical because a low-iron bauxite is needed. Although there are substantial bauxite reserves in the world, bauxite suitable for use in refractories is limited to a few districts.

Jan 1, 1977

By P. A. Tucker, C. R. Hudgens, D. E. Etter, D. L. Roesch, D. B. Martin

The equilibrium phase diagram of the Pu-Cd system is presented based on data obtained by differential thermal analysis, metallography, and electron-microprobe X-ray analysis. Liquidus temperatures range from 320° to 934°C. The system contains one congruently melting compound, PuCd, (945°C), and three incongruently melting compounds, PuCd, (800°C), PuCd, (730°C), and PuCd11 (410°C). A liquid-miscibility gap extends from 2 to 60 at. pet Cd with the monotectic reaction isotherm at 910°C. INTEREST in the potential use of plutonium alloys as reactor-fuel materials has prompted investigation of the phase equilibria in plutonium binary systems. A cursory investigation of the phase equilibria in the Pu-Cd binary system was conducted by differential thermal analysis (DTA), metallography, and electron-microprobe X-ray analysis (EMX). Extensive solid solubility of cadmium in both e and 6 plutonium was predicted1 based on atomic radii and electronegativities. Liquid immiscibility between these two elements was also predicted based on Mott's extension of Hildebrand's method. In the only previous investigation of the Pu-Cd system,2 two intermetallic compounds, PuCd11 (incon-gruent melting point 406°C) and PuCd8, were identified. EXPERIMENTAL The plutonium metal used in this work had a total impurity content of 500 ppm; the major impurities were: carbon (215 pprn), silicon (75 ppm), iron (60 ppm), nickel (40 ppm), and aluminum (25 ppm). The cadmium was reagent grade with a purity of 99.99 pet. The DTA technique for the study of plutonium alloys was previously described in detail.3 The alloys to be studied were prepared in tantalum DTA specimen capsules which were sealed by inert-gas welding. The alloys were homogenized in the liquid state in these sealed capsules which prevented the loss of cadmium by vaporization. Only the thermal arrests in the DTA heating curves were used to define the transformation temperatures of the system since supercooling affected many of the results during cooling. After the alloys were analyzed by DTA, the same alloys were used for the metallographic studies. Metallographic examinations were conducted in the manner described for plutonium alloys., No reaction was detected between the alloys and the tantalum capsules. Alloys for EMX analysis were placed in metallographic mounts together with specimens of unalloyed plutonium and cadmium which served as standards. The samples were highly polished but unetched. No protective coatings were applied to the surfaces of these radioactive specimens. Such coatings are detrimental to the excitation conditions and have been found to be unnecessary for the control of radioactive contamination. RESULTS The results of the DTA studies are presented in Table I. The phase diagram, constructed from these data plus the metallographic and EMX results, is presented in Fig. 1. The congruently melting compound, PuCd2, was identified by the occurrence of a maximum melting point (945°C) at 33.3 at. pet Pu-66.7 at. pet Cd and by the presence of a single phase in this composition.

Jan 1, 1965

By A. W. Khair

This paper presents an engineering approach to solve a complex ground control problem at reduced cost, allowing the mine to be operated safely and economically. The mine has experienced serious and complicated cutter roof problem in the entries. This cutler roof problem has delayed the advance of the entry development considerably and cost of these entries is very high due to the requirement of very heavy artificial supports. The analysis includes assessment of the cause of cutter roof and step by step action taken to improve the entry condition through appropriate longwall panel entry design and roof support system. The approach for solving the problem was two-fold: 1) to apply yield pillar concept in order to reduce the effects of in-situ horizontal stress in the roof strata and 2) to find an effective way to reinforce the roof strata and to support the fractured roof and avoid caving.

Jan 1, 1990

By G. A. Grandy, P. F. Thomas, C. D. Danecki

When considering the mill drive system for a grinding application, a large number of questions must be answered. Depending on the mill size and type, the mill can be driven by several configurations of drive systems: a single low-speed motor connected to a pinion driving a ring gear, two low-speed motors connected to two pinions and driving a ring gear, or a gearless motor mounted directly. In addition, a gear drive system can have a reducer placed between a high-speed motor(s) and pinion(s) or a power path splitting pinion stand. In some designs the reducer is integral with the pinion stand driven by a high-speed motor. The technical and commercial implications of several mill drive options are presented. Initial cost, cost of installation, cost of commissioning, and cost of operation and maintenance are presented for each drive option considered. The impact of each drive system on the design, cost and operation of the overall plant electrical system is discussed. Also, consideration is given to mill drive availability, and the potential cost resulting from delays in plant production.

Jan 1, 2001

By Toshia Ishii, Jun Kubota, Noriko Kubo

"For steel continuous castings, it is essential to control molten steel velocity at the meniscus, since the velocity is closely related to surface defects on the resultant products. Argon gas is supplied with molten steel into the mold through the submerged entry nozzle to prevent nozzle clogging. In this study, to investigate the influence of argon gas on molten steel flow, a numerical simulation was carried out by a two-phase model. Simulation results indicate that as argon gas bubbles ascend near the nozzle by their buoyancy, they induce the molten steel flow with them and resulted a meniscus molten steel flow from the nozzle to the narrow face of the mold. This flow direction is opposite to the case without argon gas. The calculated data are compared with the experimental data. The comparison shows generally good agreement between the measured and the calculated data. IntroductionIn a steelmaking process, molten steel carried by a ladle is first fed into a buffer vessel called tundish. From the tundish, it is then fed into a continuous casting mold. Molten steel solidifies gradually in the mold (the primary cooling zone) forming a solidified shell. As the solidified shell is just thick enough to support the molten steel at the mold exit, it is withdrawn through the mold by pinch rolls. It is progressively thicken as it is further cooled with water sprays in the secondary cooling zone. At the end of guide roll zone, completely solidified steel is cut into desirable lengths. Schematic view of a typical continuous casting is shown in Figure 1."

Jan 1, 1999

By F. D. DeVaney

In the course of the investigation by the U. S. Bureau of Mines and the Missouri School of Mines and Metallurgy at the Mississippi Valley Experiment Station at Rolla, Mo., on the beneficiation of the low-grade manganese ores of the country, some samples from the Cuyuna District, Linn., have been examined. The work was done under the direction of W. H. Coghill, supervising engineer of the Mississippi Valley Experiment Station. Joseph and Kinney in writing about the relative importance of Minnesota deposits of low-grade ore compared to the total reserves say: "***It has been estimated that 26 to 35 million tons of ore contain 5 to 35 per cent of manganese, and the total domestic tonnage is from 75 to 48 million tons. The mean of these values is 30.5 million and 42 million tons, so it is seen that about 75 per cent of the reserves are in Minnesota." The manganese-bearing ores of the Cuyuna district maybe roughly grouped into two classes. The most abundant ore is of the low-silica, low-manganese, and high-phosphorus type called brown are. The other type is the so-called black ore, which is characterized by a higher manganese and silica content and by a lowe phosphorus analysis than the brown ore. As a general rule the brown ore carries less than 10 per cent of manganese while the black ore contains about 15 per cent and sometimes as high as 22 per cent of manganese.

Jan 1, 1930

By Patricia R. Devine

This appendix documents the mathematical approach to deriving the components of change presented in this report. The formulation closely follows that contained in Chapter IV of the documentation for the BEA 1977 Input-Output Tables.' The basic elements for the calculations include the "use" matrix (U), the "make" matrix (M), and any of the ten columns of final demand (generically represented by the symbol y). The use matrix contains information about changes in the technological processes of production, while the make matrix describes the nature of secondary product production in each industry. We adhere to BEA conventions in maintaining careful distinctions between commodity output (c) and industry output (x). The industry-by-industry 1-0 tables supplied by NYU for use in this analysis are square matrices, with the number of commodities and the number of industries both equal to 85. The BLS table for 1982 (commodity by industry) was aggregated and adjusted to be consistent with the earlier tables. The three basic steps for estimating components of change proceed as follows for each column of final demand. 1) Calculate the actual change in output of each commodity for each of the four time periods: 1963-72, 1972-77, 1977-82, and 1963-82.

Jan 1, 1988

By S. Z. Pethö

Pillar extraction at shallow depths with small pillars that were not originally intended for secondary extraction can provide a huge benefit to the coal mining industry in those areas where a significant percentage of the remaining coal reserves are locked up in small pillars at shallow depths and where opencast mining methods are simply not as cost-effective and practical to implement. A system considering all of the pertinent geotechnical and mining aspects for the safe and efficient pillar extraction of small pillars at shallow depths at Xstrata Coal South Africa (XCSA) has been further developed and implemented as part of an ongoing improvement process addressing all of the relevant legal and associated risk aspects. This work follows on from the previous pillar extraction work carried out at the ATC, Boschmans, and Spitzkop Collieries. The process involved a number of in-house workshops and sessions arranged with all key personnel from Tavistock Colliery, and also included Professor Nielen van der Merwe of the University of the Witwatersrand, a world renowned authority on pillar extraction, towards reviewing and developing the Modified NEVID pillar extraction system employed previously at Boschmans Colliery. The system is currently being employed at Tavistock Colliery with success and no major accidents, with around 655 000 t of coal having been successfully extracted from the pillar extraction panels.

Jan 1, 2012

By L. D. Ricketts

AN older man looks back, perhaps wistfully, on a long and rather active experience, and possibly a popular and brief glimpse of some contrast between past and present may hold your attention for a few brief moments and prove useful. In the late nineties an engineer was .called on to de- sign and build two copper ore concentrating mills of 400 tons average daily capacity. There were larger mills than this at Washoe and elsewhere, but a 400 ton' mill was a large one as mills went over thirty years ago, and one might say a large mill of those days could crush a ton of copper ore in 216 seconds. In the mills I refer to steel construction and the conveying belts were introduced into the copper industry and rein- forced concrete came shortly after. Since then we in the West have ever been faced with a constantly de- creasing tenor in the grade of our copper ores and a constantly increasing demand for our product, and we have therefore been obliged to call for far larger castings and finished machines than were formerly used. The mechanical engineer has also enabled us to accomplish notable economies in power generation and distribution. Ore handling and crushing have been simplified and through the introduction of reagents to induce physical or chemical reactions, or both, our older methods have been vastly improved or even supplanted by new and better ones and our recoveries greatly improved.

Jan 1, 1929

By J. Drzymala

Particle beneficiation tests are often conducted to determine how the recovery of a key component of a particle mixture varies with overall product yield, i.e., the separation curve. The results can be misleading when an attempt is made to determine the effect of feed grade by comparing separation curves representing different feed grades or key component concentrations. This is a shortcoming of the conventional recovery versus yield diagram, which may not appear to be affected by feed concentration. To overcome this shortcoming, a method is presented for transforming and normalizing the recovery and yield coordinates so that the separation curves representing dif-ferent feed concentrations are directly comparable.

Jan 1, 2007

By Peter R. Sanford

Cyanides are present as a dilute constituent of streams from a variety of metallurgical and mineral-processing operations. In addition, a cyanide concentration in excess of approximately 100ppb is toxic to aquatic life, and consequently these operations require a waste-treatment process to reduce the already dilute cyanide species by several orders of magnitude. Furthermore, the waste streams may have flowrates in excess of a million gallons per day. The paper reports on research conducted with a laboratory?scale electrochemical porous (graphite felt) electrode (anode) flow-reactor, which was conducted in conjunction with a computer-aided simulation of a mathematical model describing the intrinsic rate-phenomena associate with the electrode processes. The laboratory-scale cell, of rectilinear geometry, was found to be capable of reducing a feed-stream anolyte (KCN-KOH and supporting electrolyte of a single salt ? K2SO4) with a cyanide concentration of 10ppm, to less than 100ppb, at current efficiencies in the neighborhood of 50%. The computer simulation of the cell performance based on the mathematical model (and constraints imposed for tractability) was found to provide only for qualitative agreement.

Jan 1, 1998

The sphere of operations of dry crushing has been so much enlarged of late years that the following notes with reference to its advantages and limitations, and also some practical results in connection with the crushing of gold ores will probably be of service to the members of the Institute. Until recently, with one notable exception that of the Mt. Morgan Gold Mine, dry crushing has only been practiced to a very limited extent in Australasia, and elsewhere it might be said to belong to industries other than mining Its sphere of usefulness depends on the fact that the' product is delivered in a dry state without the separation of the finer particles from the coarser to any appreciable extent, thus enabling the following advantages to be achieved with different ores.