Search Documents

By William A. Hockings

Methods for the measurement of liberation of finely ground iron ores are described. The general method consists of separating a sample of the ground ore into a number of size fractions, followed by measuring the liberation of each fraction. The size separation has been done using electro-formed screens of 20-, 10-and 5-micrometer apertures, and also by air elutriation. Liberation (i.e., the distribution of compositions of individual particles) has been measured by optical microscopy. A computer pro-gram was used to adjust the raw count data so that it agrees with the chemical analyses of the size fractions. Various ways of presenting the results are given, and Some applications of the results to flotation processing are discussed.

Jan 1, 1981

By George A. Burrell, G. W. Jones, Frank M. Seibert

In this bulletin, the style of Bulletin 42 has been closely followed. Much of the material is reprinted on the following pages in its original form, and changes have been made only where manifestly neces- St,ry. Laboratory methods have been brought up to date. Some types of apparatus described in Bulletin 42 have now become obsolete and newer designs are described instead. The authors hope that this bulletin will be of as much service as was Bulletin 42.

Jan 1, 1926

The intent of this manual is to provide guidelines for inspectors of drilled shaft construction otherwise referred to as drilled piers, caissons or bored piles. It should also be helpful to train beginning geotechnical engineers with limited first hand experience or for geotechnical engineers who are training inspectors. It is expected that the general guidelines and procedures described here will be supplemented by local geotechnical engineers working in a particular region based on local practice and experience. Since drilled shaft construction procedures vary widely based on local geology and size of project, an all-inclusive manual is not considered practical. This manual focuses on traditional topside inspection for routine drilled shaft construction. Other inspection and evaluation methods that rely on electronic equipment are available, but these methods require extensive training and experience in the interpretation of results. These more sophisticated methods of drilled shaft inspection and evaluation are common in construction, but they are usually provided by specialty subconsultants. The subconsultant will typically submit a report for each shaft, which will be reviewed by the geotechnical engineer. Other manuals are available to describe the electronic methods of drilled shaft inspection.

Jan 1, 2004

By Robert T. Mann

This paper is one of a series being prepared for and published by the United States Bureau of Mines on the quarrying, crushing, and grinding of limestone for cement manufacture. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total coats. It is recognized that publication of total costs might in many instances cause embarrassment to individual producers, as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. ACKNOWLEDGMENTS The author wishes to acknowledge the assistance of J. B. Thoenen, mining engineer of the Bureau of Mines, in the preparation of this paper.

Jan 1, 1933

By L Scheunis, A Van den Bulck, E Jak, K Verbeken, M Shevchenko, R Starykh, I Bellemans, P-J Boeykens

As a result of the globally increasing consumer use of electronic devices, it is expected that pressure will increase on the supply chain of precious metals. Hence, recycling of these electronics becomes increasingly important, as well as optimising the current processes. One major issue in metallurgical processes is the amount of metal that is lost into the slag. This metal loss is inherent to the production process and therefore, additional processing steps such as slag cleaning may be required. Slag cleaning can be done in electrical resistance furnaces where heat is produced using the Joule effect, making the slag’s electrical conductivity an important operating parameter. Since slags are ionic liquids, the electrical conduction happens via the movement of ions which is called ionic conductivity. However, within the presence of transition metal oxides, a second mechanism of conductivity occurs as electrons are able to hop from one transition state to another, which is known as electronic conductivity. As ‘FeO’ is a common slag component in the non-ferrous pyrometallurgical industry, both mechanisms are present, but their proportions vary with the respective amounts of the two forms of the multi-valent ions and hence, with the oxygen partial pressure. The goal of the present study is to develop an experimental set-up and methodology for measuring the electrical conductivity of synthetic SiO2 – CaO – AlO1.5 – ‘FeO’ slags at various oxygen partial pressures.

Jun 19, 2024

By George E. Aikens

Prolonged subzero climatic conditions impose some unique engineering problems for the developer and operator of open-pit mines in the Far North. The remoteness of the job site and the extremely cold, long, dark winters severely tax both man and machine in the quest for the Arctic's rich mineral wealth. Undoubtedly the singular most troublesome problem for the engineer is Permafrost which underlies about 201o of the land area of the world and about 85% of the state of Alaska. Permafrost has its impact on building construction and mine excavation, while posing a more pervasive threat to the-delicate ecologic balance within the Arctic wilderness. Yet the difficulties associated with mining up North may not be as overwhelming as has been previously supposed. For example, the lowest temperature recorded at Point Barrow is -560F, whereas Montana has recorded -69.7° F.. There are no specially designed machines for mining and construction in the Arctic, and efficient equipment utilization is maintained through proper operation and servicing techniques. However, neither equipment or people can be assumed to function normally at -40°F. Special techniques in drilling, blasting, and ripping are being used to yield economically competitive ores. Overall, a fundamental understanding of the nature of Permafrost will allow the engineer to deal expeditiously with an Arctic mining venture and at the same time to deal fairly with Arctic environment.

Jan 1, 1972

By P. G. Claridge, G. P. Holmes, M. A. Redfearn

"IntroductionThe purpose of this chapter is to describe current practices in operation and maintenance of flotation circuits in Canadian mineral processing plants. The chapter consists of five sections covering description of equipment, typical flow diagrams, operating practice, instrumentation and maintenance. The approach to this subject matter is intended to be practical in nature, hence no deeply technical treatment of flotation theory will be included.Flotation is an extremely common method of beneficiation of ores. Reasons are the relatively low cost of flotation compared to many other processes, the wide range of minerals to which flotation may be applied and the high efficiency of separation which can usually be achieved. The flotation process as we know it today has been developed within this century and it has had a major impact on the mining industry. While flotation is commonly considered to be important because it provides a relatively simple method of separating minerals in complex ores, the availability of flotation has also made a multitude of mineral deposits in Canada into economically viable mining operations because it allowed production of a concentrate of valuable minerals from the ore. These concentrates could then be transported from geographically remote locations to centraHzed plants for further processing, although the existence of the remote and perhaps small ore body alone would not have justified installation of metallurgical processing plants on site and the grade of ore would not have justified direct shipment of ore.Some of the more common minerals concentrated by flotation are sulphides of copper, nickel, cobalt, iron, zinc, molybdenum, lead and arsenic, as well as non-sulphides such as sodium chloride, potassium chloride, phosphates, silicates, chromite, fluorite, limestone and coal. Precious metals are also recovered by flotation, generally in association with another sulphide mineral."

Jan 1, 1989

By T. Emery, D. Sweet, J. Bourgeois, M. Gomez, B. Seymour, J. Feiler

For traditional underhand cut-and-fill mining operations, it can be challenging to design a suitable cemented paste backfill (CPB) mix that can meet the necessary strength requirements and yet maintain its ductility. In deep underground metal mines, the CPB must achieve a high enough strength to be competent under high stress conditions while also remaining ductile enough to withstand high strain from squeezing ground as underhand mining continues under backfilled stopes. To eliminate ground falls that result in injuries and fatalities, researchers from the Spokane Mining Research Division (SMRD) of the National Institute for Occupational Safety and Health (NIOSH) have partnered with Aerix Industries, a producer of concrete additives, to study the effects of foaming agents on the strength and ductility of CPB. This laboratory study examines the impact of various amounts of foam additive on the strength and ductility of CPB mix designs, using binder and tailings provided by Hecla Limited from the Lucky Friday Mine

Mar 2, 2022

By K. Bommer

"In today’s fast paced, globally competitive world, reliability and machine uptime are of the utmost importance to a successful operation. Along with these targets more emphasis is being put on cost reduction and decreasing the environmental impact of the overall system. To achieve these goals, automatic lubricators and lubrication systems have been used in many industries for years and are now becoming a common tool in the mining industry as well. These systems are able to provide proper lubrication amounts at the proper times autonomously, helping to keep the machines running smoothly while minimizing the physical support required. Copper mines in the southwest have begun utilizing auto lubrication to avoid mistakes and unplanned shut downs on critical equipment. This paper will describe the engineering behind these products and review case histories where these tools have been successfully utilized in the mining industry. INTRODUCTION In a dirty, dusty, wet environment, where machine uptime is imperative, proper lubrication of bearings is the only way to survive. With the push for cost reduction and mines striving to lower their environmental impact and increase worker safety according to MSHA guidelines, the old lubrication practices have come under scrutiny. It is no longer encouraged or cost effective to have maintenance personal walk from point to point throughout the entire mine pumping a shot of grease into each bearing once per shift. Automatic lubricators and lubrication systems have been on the market for years but recently, as the market focus has changed and technology has developed, the use of these systems has begun to rise in the mining industry. Automatic lubrication systems can be as simple as a single point lubricator lubricating one (1) bearing or a more complex system lubricating numerous bearings. With system design, the automatic lubricator provides a preset amount of grease to a bearing at regular, predetermined intervals. The systems designed to lubricate more than one bearing contain grease pumps of some design and possibly PLC controllers which can be used to remotely adjust and monitor the system. As can be seen in Figure 1, the right amount of lubrication can be achieved much more reliably with automatic lubricators. Depending on application needs, the market now has products to fit almost every wish list. This paper is going to focus on the single point systems that are lower in cost but are still being effective."

Jan 1, 2015

By JIACHENG XIE, XUEWEN WANG, QINGBAO BAO, ZEWEN YAN

The general application of memory cutting technology to shearers is improving the intelligence of the working face, but it has its limitations. It is only suitable for conditions where the environment of coal seam is changing slowly. It compensates for the cutting height by changing the fuselage attitude, and frequently adjusts the height to control the learning cutting trajectory, but due to the problems of shearer control and height adjustment accuracy, it cannot adapt to and compensate for the change of cutting height in a timely manner, resulting in poor cutting accuracy. This study puts forward a virtual memory cutting method based on prediction of the shape of the armored face conveyor (AFC). The integrated key technologies include generation of virtual teaching cutting curve, height adjustment strategy of front and rear drums, cutting

By R. H. Roberts

The Environment Weipa is located at 12° south latitude on the west coast of Cape York Peninsula, North Queensland, Australia. The climate is tropical with most of the 1 600 mm. average annual rainfall falling between November and March. During the short winter months (May/ August) the weather is clear and pleasant, with temperatures seldom exceeding 27°C.Throughout the remainder of the year, conditions are frequently oppressive due to consistent high ambient temperatures accompanied by high humidity. The terrain is of low relief, and generally not more than 6 to 10m. above mean sea level adjacent to the coast. The coastline features numerous short estuaries which discharge run-off from the heavy rains collected by creeks and rivers. The whole area is covered by an open forest, the predominant species of which is Eucalyptus tetradonta. These eucalypts have only limited commercial value and are heavily infested with termites. Despite the fact that Weipa is close to the location of the first reported sighting of the Australian coastline by a European (William Janz - 1606), it remains very isolated. There is no developed road or rail connection to centres of population, so that transport of practically all products, personnel and materials to and from Weipa is by sea and air. Cairns (population 49 000) is 580 km. by air and 670 nautical miles by sea; Brisbane, the

Jan 1, 1977

By D. N. Thurston

Luscar Stereo commenced construction of the mine at Coal Valley, Alberta, in August, 1976. It is designed to produce approximately 2.5 million clean short tons of steam coal annually - 2.0 million tons per year being committed to Ontario Hydro and 0.5 million tons per year being committed to Neptune Terminals for sale on the export market. The project involves constructing a heavy-media coal preparation plant, erecting a 42-cubic-yard dragline, constructing a shop/office complex, and developing three surface mining zones and associated facilities. As there were no existing facilities in the Coal Valley area, it was necessary to establish access roads, an airstrip, temporary utilities, fuel supplies, a construction camp, rail upgrading and communication services.

Jan 1, 1978

By William R. Yernberg

The 2003 Rapid Excavation and Tunneling Conference (RETC) was held at the New Orleans Marriott, New Orleans, LA, June 15-18. The New Orleans conference was the 16th since the RETC was formed in 1971. This year’s conference was sponsored by the Society for Mining, Metallurgy, and Exploration, Inc.(SME), with co-sponsorship of the Construction Institute of ASCE. Attendance at the meeting was 1,178, a conference record. This was up significantly from the771 attendees at the 2001 meeting in San Diego, CA. The RETC was formed to “advance the engineering and scientific knowledge of rapid underground excavation and tunneling through interdisciplinary meetings, publications, technical-educational exhibitions and encouragement of research.” The RETC conferences are now held every other year. They provide an opportunity for individuals to meet with designers, contractors and manufacturers associated with the tunneling industry to share experiences in all phases of tunnel design and construction.

Jan 1, 2003

By K Taylor

Small scale tests have been conducted in blasting vessels in the laboratory, where the effects of explosive composition, charge diameter, explosive confinement as well as additives to the explosive were examined on NO, NO2, CO and CO2 production. Fumes were analyzed continuously using a flue analyzer, providing analysis every 15 seconds. The results were compared to previous work conducted in the laboratory and to literature findings. It was found that the type of the explosive was the most dominant factor with emulsion explosives producing significantly less amounts of toxic gases. ANFO was shown to always produce nitrogen oxides, even when fuel rich. Tests were also conducted by detonating explosives in broken rock, simulating the release of products of detonation during the formation of a muckpile. Products of detonation were affected by the presence of atmospheric air or rock around the charge. Gaseous products of detonation migrated through the rock piles at different rates, resulting in a change of toxicity values over time. In the small scale experiments, CO appeared to travel faster than CO2 while NOX was not identified. Analysis of the gases that were released during digging, several hours after the blast, resulted in high temporary concentrations of toxic fumes.

Jan 1, 2014

By J Player, G Sweby, S Webber, E Jones

Seismic systems are a tool for the monitoring and forecasting the rock mass response to excavation. Common issues encountered at mine site audits and reviews are: how to design an effective seismic system, implementation of the design, interpretation of seismic source results and understanding the reliability of the seismic source. These issues are often a function of several items including: • Experience of site personnel in undertaking seismic system design. • Personnel not envisioning multiple phases of system expansion to understand system robustness issues. • System design/expansion occurring in response to damaging seismic activity rather than planned expansion of a system • The mine access development is often localised in comparison to the total orebody being mined hence, planning sensors in longholes in advance of development rather than in short holes close to development will improve the three-dimensional aspect of the network. • Limited site processing of the seismic event data, hence engineers do not see the uncertainty associated with event location, size, source and system layout. Mine site users require a framework to appreciate the challenges and limitations in locating large events. For example, event locations are given as precise measurements (to the nearest centimetre) whereas the volume of deformation resulting in the event often has dimensions of tens of metres or more (as defined by the source radius). A stronger awareness of the uncertainty of rock mass yield within large seismic sources will assist site users in the interpretation of rock mass damage. The encountered design and implementation errors are reviewed and discussed with a practical set of rules presented to provide a robust seismic system that provides consistent results and increases the user’s understanding of uncertainty in source location and size. The authors’ experience across multiple mine sites, seismic systems and damaging seismic events over a 30 year period has been summarised into practical rules for site personnel of all experience levels.

Nov 29, 2022

By John E. Kelley

Laboratory equipment, which simulates abrasive impacts between steel and minerals that might be present during pneumatic transport of coal, was used by the Bureau of Mines to characterize the potential explosion hazard of such collisions in an atmosphere of fine coal dust, air, and methane. A variety of coal mine rock materials, including sandstone, limestone, and pyrite-bearing limestone, were impacted with specimens of pipeline steel. Tests were con-ducted in atmospheres containing zero to 6.4 vol-pct methane mixed with zero to 300 mg/l coal dust. Coal dust in air alone was not ignited by abrasive impacts, but additions of as little as 1 vol-pct methane to the coal dust and air mixture resulted in ignitions. Steel impacting against sandstone caused ignitions in mixtures of coal dust, air, and methane, and the probability for ignitions increased with an increase in methane. No ignitions occurred with impacts of steel on lime-stone or pyrite-bearing limestone, even when large showers of sparks were produced. Studies of the effect of tangential collision velocity showed that no ignitions of coal dust, air, and methane occurred below 900 fpm (4.57 m/sec). Ignitions in coal-air-methane mixtures were found to be caused by a hot friction-induced smear on the impacted rock at the impact site rather than by sparks. High-speed photography was used to verify this observation.

Jan 1, 1976

By S. T. Johansen, B. T. Løvfall, T. Rodriguez Duran, J. Zoric

A methodology for building pragmatic physics-based models is here adapted to predict the erosion of ladle linings in the steel industry, in order to support operators when deciding whether the lining can be used safely for another heat. A defective lining may allow 140 t of molten steel to spill, with disastrous consequences for workers and plant. The adopted work flow for the development, challenges faced, and some model results are presented. One key learning outcome is that model development should allow time for maturing the process understanding, as well as for many iterations by ‘questions-responses and actions’ at various stages in the model development. Good interaction between the development team and industry case owner is an important success factor. Combining or extending the model with the use of machine learning and cognition-related methods, such as knowledge graphs and self-adaptive algorithms, is discussed.

Apr 16, 2024

By Martin Hertzberg

This Bureau of Mines study concerns the use of the tube bundle method as a sensitive and reliable detector of mine fires. The method involves the pneumatic, sequential sampling of many points in a system through branching tube bundles that lead to a single analytic station of high sensitivity, good reliability, and convenient location. Two serious limitations inhibit its use: the relatively slow response times for long lengths of narrow sampling tubes and the wall-diffusion losses for submicrometer smoke particulates. These limitations were quantitatively evaluated by measuring tube transit times and smoke particulate transmissions as a function of tube length, diameter, and pressure drop. The comparison of the data with theory offered the challenge of extending the classical, incompressible flow solutions to the two compressible cases: isothermal and adiabatic. New equations were derived for these cases, and the measured transit time data gave reasonable agreement with calculated solutions in both the laminar and turbulent regimes. The measured transmission losses of smoke particulates from several combustion sources compared favorably with those expected from Brownian diffusion losses to the interior walls of the sampling tubes. Traveltime and smoke transmission graphs are provided and, pump power requirements are estimated.

Jan 1, 1976

By D. A. Larson

The Bureau of Mines conducted research to develop preliminary engineering data necessary if the cobalt-rich manganese crusts that occur in the Exclusive Economic Zone (EEZ) of the Hawaiian Archipelago are to be mined. The research was divided into the following sections: (1) physical, mineralogical, and chemical descriptions; (2) mechanical property testing, such as compressive strength, tensile strength, and a rippability index; and (3) mechanical cutting characteristics, including average and peak cutter forces, the specific energy, and cuttings size distribution. Section 1 utilized microscope, X-ray powder diffractometer, and electron microprobe analyses. Section 2 utilized standard mechanical property testing techniques. Section 3 utilized a converted planer mill with full-size coal cutters to fragment the crust and substrate samples. The manganese crust samples were mainly manganese and iron oxides and hydroxides with an average cobalt content of 1 pct and had a nucleus or substrate of rock or sediment. The significant results shown by the mechanical property and cutting tests are that the crust and all but two types of substrates (basalt and trachyte) are weak materials and easily cut with standard drag cutters. The crusts are generally comparable to medium hard coal in strength and in their resistance to cutting.

Jan 1, 1987

By John K. Alley, Robert C. Johnson

The primary objective of the research was to grow aluminum borate whiskers or fibers and to determine their properties . Molten salt bath and vapor deposition methods were used for synthesis . Whiskers exceeding 25 mm in length were grown . The best results were obtained by vapor deposition and most of the data presented were determined on whiskers produced by this method of synthesis . Three different aluminum borate compositions ( 4.8A1203 B₂03 , 3.8A1203 B203 , and 2.5A120, B203 ) were identified by X- ray and chemical analyses . The aluminum borates 4.8A1203 B20, X- ray diffraction pattern was indexed . Optical data were obtained on the three aluminum borates . In addition the following whisker properties and growth factors were determined : ideal atmospheric dewpoint for vapor deposition method , near 65 ° F ; temperature range of whisker formation , 1,000 ° to 1,400 ° C for the molten bath method of synthesis , > 1,000 ° to < 1,400 ° C for the vapor deposition method ; whisker growth rates by the vapor deposition method , maximum 12 mm per hour ; raw material vaporization , 50 to 60 percent of the fluoride lost in 1 hour ; tensile strength , maximum obtained 174,162 psi ; melting points , ranged from 1,675 ° to 1,795 ° C.

Jan 1, 1965