Search Documents

By C. S. Compton, T. E. Marshall, D. R. Dolinar, R. Grau, L. J. Prosser, A. T. Iannacchione, D. C. Oyler

Unrecognized roof beam failures resulted in 69% of the falls of ground injuries occurring in underground U.S. stone mines from 1990 to 1996. Field investigations at 45 underground stone mines suggest that excessive beam sag or deflection is the principal unstable roof behavior characteristics associated with miner injuries. Laminated roof structures, common in most underground stone mines, allow the immediate roof to separate into distinct beams. The timely determination of roof beam deflection could provide stone miners with advanced knowledge of potentially hazardous roof. Existing methods to assess roof conditions consist of observational and monitoring techniques. Observational techniques include open drillholes, sounding, wedging, and borescopes. Monitoring techniques include scratch tools, extensometers, telltales, Miners Helpers, and Guardian Angels1. Miners have difficulty utilizing these techniques because roof beams are located an average of 8 m(26.5 ft) above the miner’s head in environments that are dark, dusty and noisy and these deflections are measured in millimeters of movement. To help mitigate the potential for falls of ground injuries to underground stone miners, the National Institute for Occupational Safety and Health (NIOSH) has developed the Roof Monitoring Safety System (RMSS) to aid in monitoring dangerous levels of roof beam deflection. If enough site-specific information is collected and placed on highly visible maps, individual mining operations could establish general guidelines for responding to specific roofbeam deflection occurrences. This would help in implementing a pro-active, comprehensive roof control plan for reducing falls of ground injuries.

Jan 1, 1999

By H. G. Turner

The coals mined in the area known as the anthracite fields of Pennsylvania have always been recognized commercially as anthracites. In the literature, however, some of these anthracites have been called semi-anthracites by various writers. The coals mined in Sullivan County, especially those from the Bernice field, have been recognized commercially both as anthracites and semi-anthracites. In the literature they have almost always been referred to as typical semianthracites, although Franklin Platt,1 in his report to the Pennsylvania Geological Survey, uses the terms semibituminous, semianthracite, and anthracite in describing them. The purpose of this paper is to endeavor to dispel the confusion of names used to describe these coals and to supply further information that will permit a logical and definite classification. Most of the confusion of the past has been due to the impossibility of securing enough fresh face samples from which to draw sound conclusions; some of it was due, no doubt, to lack of standard methods of analysis, and of course, to the ever-present lack of definition of boundaries from the standpoint of classification. Map Showing Lines of Equal Volatile Matter and Lines of Equal Specific Gravity As a foundation for this work the writer constructed a map showing lines of equal volatile matter and lines of equal specific gravity throughout the anthracite and semianthracite regions. The points on these lines were determined from a study of analyses of 214 face samples from 28 mines and composite analyses from 18 different breakers. These samples were collected through the joint efforts of the U. S. Bureau of Mines and the Anthracite Institute. The Bureau of Mines standard method of sampling was used in all cases. All analyses were made by the Bureau of Mines and are used here with its permission. The

Jan 1, 1934

By J. W. Klokow, K. L. Riemer, R. I. L. Ferreira

As a result of the increased depth of mining in the South African gold mining industry mining induced seismicity is a severe problem. One of the strategies within the industry to contain the problem is to incorporate a system of regularly spaced stabilising pillars into mine layouts. At the Driefontein Gold Mine a system of closely spaced dip pillars is used to contain seismic energy emissions. Comparisons of seismic data for several mining clusters initially indicated a possible measure of success in the containment and occurrence of larger events. A detailed analysis of data over a 5-year period since the start of mining however, has revealed a delayed seismic response to the increasing strike spans. Significant changes marked by an increase in certain seismic variables have been observed at mining spans of between 100 to 120 meters and could be of significance to pillar spacing in the design of deep level mining layouts. La sismicité occasionnée par l’exploitation minière est un problème grave dans les mines profondes de l’industrie minière aurifère en Afrique du Sud. Une des stratégies utilisées dans l’industrie a été de maîtriser le problème en incorporant un système de piliers de stabilisation régulièrement espacés dans la disposition des mines. A la Driefontein Gold Mine, un système de piliers de pendage proches les uns des autres est utilisé pour contenir les émissions d’énergie sismique. Au début, des comparaisons de donnés sismiques pour plusieurs groupes d’extraction ont indiqué un succès possible dans la limitation et l’occurrence d’évènements sismiques. Cependant, une analyse détaillée des données sur une période de 5 années a révélé un délai entre la progression de l’extraction et une réponse sismique accrue. Des changements considérables dans les variables sismiques ont été observés dans des intervalles d’extraction entre 100 et 120 mètres, ce qui pourrait être significatif pour l’espacement des piliers dans la conception de la disposition des mines de fond. Resultierend aus den zunehmenden Tiefen des Bergbaus in der südafrikanischer Goldbergbauindustrie stellt sich die vom Bergbau hervorgerufene Seismizität als bedrohliches Problem dar. Es war eine der Strategien innerhalb der Industrie, das Problem dadurch einzudämmen, daß regelmäßig plazierte Stabilisierungspfeiler in den Bergbaulayouts inkorporiert wurden. In der Driefontein Gold Mine wird ein System von knapp aneinandergesetzten im Abfallbereich befindliche Pfeiler benutzt, um seismische Energieemissionen einzudämmen. Vergleiche der seismischen Daten für mehrere Bergbaugruppen zeigten anfangs ein mögliches Maß von Erfolg in der Eindämmung und im Auftreten von größeren Fällen an. Eine ausführliche Analyse von Daten über einen 5jährigen Zeitraum hat jedoch ergeben, daß eine Verzögerung zwischen der Progression des Bergbaus und einer erhöhten seismischen Reaktion besteht. Bedeutende Änderungen in den seismischen Variablen wurden an Bergbauspannen von 100 bis 120 Metern beobachtet und könnten für Abstandsbemessung von Pfeilern im Design des Tiefbergbaulayouts von Bedeutung sein.

Jan 1, 2003

Refractory copper ores (CROs) in central Africa contain copper minerals that are locked up in a micacious solid matrix or associated with carbonate, sulfide and phosphate minerals. Several researchers have reported that the recovery of copper from CRO material by an acid-leaching process is not economically feasible, due to the presence of excess gangue-acid-consuming minerals such as calcites, dolomite, asbolane and iron oxides. Since the proportion of acid-insoluble copper (CuS) is about 28% of total copper and total free sulfur is extremely small, sulfide flotation was considered unfavorable. Consequently, hundreds of millions of tons of CRO material have been stockpiled specifically at the Nchanga Mine of Zambia. In terms of copper distribution in CRO material, a significant portion of total copper exists as carbonates (39%) and oxides (17%), while 28% of the copper is acidinsoluble (CuS). The rest of the copper is in the form of carbonates (16%) and (hydr) oxides (17%). This means that only about 72% of total copper is recoverable through the non-oxidative acid-leaching process. In this study, batch leach tests were performed on CRO solids (d95 = 95%) to establish the gangue acid consumption values at different feed pH values and to evaluate the leaching characteristics of copper, manganese and iron within the CRO material. Subsequently, continuous leach tests were performed on CRO solids (106 um, 80% passing) using optimum leach conditions derived from batch tests. This paper aims to show that sustainable copper recovery can be achieved by selecting leaching conditions whereby gangue acid consumption (GAC) values become significantly small and the final concentration of manganese and iron in the leach solution are appreciably low.

Nov 1, 2011

By N. J. Olson, G. W. Toop

A series of equations previously derived for calculating ternary thermodynamic properties using binary data has been applied to the problem of predicting ternary phase diagrams and quaternary excess free energy. The methods are considered to be rigorous for regular ternary and quaternary systerns and empirical for nonregular systems. The equations have been used to predict ternary phase boundaries in the Pb-Sn-Zn system at 926°K and the Ag-Pd-Cu system at 1000ºK. Calculated quaternary excess free-energy values are presented for the Pb-Sn-Cd-Bi system at 773°K. A method for predicting the location of ternary phase boundaries would be a useful supplement to experimental measurements in ternary systems. This has been recognized with the considerable work that has been done to find models to predict or extend thermodynamic properties and phase diagrams in binary and ternary systems1-18 for which direct experimental measurements are limited. With the access to highspeed digital computers and mechanical plotting devices, it is currently rather easy to compare mathematical models with experimental data. The regular-solution model is consistent with systems which exhibit negative heats of mixing, positive heats of mixing, and miscibility gaps, and therefore it is applicable to simple phase diagrams. The purpose of this paper is to illustrate the use of regular-solution equations to predict, empirically, phase equilibria in some types of nonregular ternary systems. Corresponding equations for regular quaternary systems are given and used to calculate empirical quaternary excess free-energy data. METHOD FOR PREDICTING THE LOCATION OF TERNARY PHASE BOUNDARIES USING BINARY DATA Meijerin1,6 has used the regular-solution model to calculate common tangent points to ternary free energy of mixing surfaces and hence to determine phase boundaries in ternary systems involving miscibility gaps. He used the following equation to calculate ternary excess free energy of mixing values: stants characteristic of the binary solutions, and Ni is the mole fraction of component i. An alternate expression which gives for regular solutions as a function of binary values of along composition paths with constant N1/N2, N2lN3, and N1/N3 may also be derived:15 ternary r xs 1 ?c-*n.Ti*.U*. This expression for is more useful for the empirical calculation of ternary excess free-energy values for nonregular systems because actual binary AFXS data may be used in the expression rather than attempting to find suitable constants for Eq. [I]. The results of this feature of Eq. [2] are illustrated in Table I where calculated excess free-energy values for the Ni-Mn-Fe system at 1232°K are compared with experimental data of Smith, Paxton, and McCabe.19 Although regular-solution equations have been shown to give calculated thermodynamic quantities which agree quite well with experiment for single-phase nonregular ternary systems,14,15 care should be exercised in the use of the equations to predict thermo-dynamic properties of multiphase ternary systems in which strong compound formation is suspected. This precaution is consistent with the simple regular-solution model which for negative values of ai_j will indicate a tendency toward compound formation but even for very large negative values of ai-jwill not give multiphase binary or ternary systems involving a distinct stable compound. Hence, calculated ternary free-energy data using Eq. [2] might be expected to vary between being rigorous and poor, in the following order, for ternary systems which are: a) regular solutions, b) nonregular single-phase liquids in which random mixing is nearly realized, c) nonregular single-phase solids, d) nonregular multiphase systems exhibiting miscibility gaps, e) nonregular multiphase systems with binary compounds but no ternary compounds, f) nonregular multiphase systems with highly stable binary and ternary compounds. The calculated data will be expected to be least accurate for the last two cases. The general method adopted in this paper involves two-dimensional plots of ternary activity curves. The principle used is that tie lines indicating two-phase equilibria join conjugate phases a and B for example, for which a1(a) = a1(B), a2(a) = a2(B), and a3(a) = a3(B). Tie lines may be determined by plotting the ternary activities of two components along an isoactivity line for the third component and the unique points where the above equalities hold may be found graphically.

Jan 1, 1970

By Martin Langenderfer, Catherine Johnson, Phillip Mulligan, Kelly Williams

The physical geometry of a charge has a direct correlation to the geometry of the shock wave. This relationship appears strongest within the boundaries of the visible fireball. As the shock wave propagates outward past the limits of the fireball, the theory states that the geometry of the shock wave should even out and become more spherical. This paper investigates pressure vs. time at two distances, one ‘Near Field’ at the extent of the fireball and one ‘Far Field.' The two Fields were instrumented with three free-Field pressure probes from PCB oriented at 0, 45, and 90 degrees to the front face of the charge, in the same horizontal plane as the charge. This orientation allows for the comparison of the shock wave from the face and vertices of the charge. All the pressure sensors were connected to a Data Acquisition System (DAS) recording at 2 million samples per second (2MS/s). Two high-speed cameras, a Phantom and an MREL Ranger II, recorded the detonations for qualitative examination of the fireball, and the shock wave. Three charge geometries were used and compared to the shock propagation of a sphere. The other geometries tested are cylinders, cubes, and tetrahedrons. Charges were made from a PETN based sheet explosive. In the Near Field, a lower pressure is observed along charge vertices with highest pressures from each face. In the Far Field, vertices record a higher pressure, possibly due to the shock waves from the adjacent faces intersecting, indicating that shock pressures do not always even out in the Far Field. This paper will describe the methodology and findings of this experiment and attempt to determine causality for trends in the data gathered.

Jan 1, 2018

By S. J. Lui

Sodium oleate was an effective diaspore collector, whereas chelate collector OL2 showed certain collecting power over diaspore and nonionic surfactant OL3 showed little collecting ability. Then experiments were carried out using sodium oleate as the main collector with the addition of OL2,OL3 to study the influences on diaspore flotation, it could be seen from the experiments that accelerants had a marked influence on the recovery of diaspore, which could be raised by 10%, and the addition sequence also affected the flotation behavior: the best results could be gained when the accelerants were mixed thoroughly before adding and the best ratio of collector OL1 and accelerant OL2, OL3 stood at 30:2:1. Based on the calculation of the ingredients in the sodium oleate solution, sodium oleate reacted with surface of the mineral and formed the acid-soap polymer [HOl?Ol-] when pH was about 9. Zeta potential test showed the accelerant promoted the absorption of collector on the mineral surface, which lowered zeta potential. As could be seen from surface tension experi-ments, the addition of accelerant OL3 lowered the CMC value of OL1 solution, which was equiva-lent to raise the power of the agents. Further Infrared Ray experiments showed the co-absorption of OL1 and OL2 make aluminum oleate on the mineral surface more stable. Up till now, the mixed reagents with sodium oleate as the main collector, combined with other two accelerants had been used in the Zhongzhou concentration plant, which is the first diaspore flotation plant in China.

Jan 1, 2014

By Hiroaki Kawamura, Takeshi Yoshikawa, Kazuki Morita, Yutaka Yanaba

"To develop an alternative metallurgical process for phosphorus removal in the production of solar-grade silicon (SOG-Si), slag treatment of metallurgical-grade silicon (MG-Si) was conducted, followed by acid leaching. Phosphorus-doped silicon alloy or MG-Si containing certain amounts of phosphorus and calcium was reacted at 1723 K and 1773 K with CaO--CaF2 of several compositions. Phosphorus removal from the molten silicon into the slag phase was confirmed by reduction to phosphide ions, P3-, and phosphate ions, P3-. These ions were separately determined using a wet chemical analysis method developed by ourselves. The highest phosphorus distribution ratio obtained was 2. 7 after reaction for 18 h with 17.5 mass% CaO--CaF2 slag. We then conducted acid leaching of the silicon and achieved removal of a large fraction (over 90 % ) of the phosphorus, which was much higher than that obtained by ordinary oxidizing slag treatment.IntroductionIn recent years, the production of solar cells has been increasing rapidly. Because of this, the demand for solar-grade silicon (SOG-Si) has also been growing rapidly. The development of lower-cost mass production processes is therefore needed to provide silicon feedstock. Phosphorus is one of the impurities in metallurgical-grade silicon (MG-Si). Because of its large segregation coefficient (kp = 0.35) [l ], it is difficult to remove phosphorus using a solidification refining process. Vacuum melting is considered to be a promising method for removing phosphorous from MG-Si [2], but the issues of high cost and large energy consumption have still to be resolved.Slag treatment is often used to remove impurity elements by oxidizing reactions during general oxidation refining processes. For example, phosphorus in molten steel is removed into a slag phase as phosphate ions, PO4 3-l-, by the following reaction:"

Jan 1, 2013

Calcium carbonate has three polymorphs: calcite, aragonite, and vaterite. Needlelike aragonite CaCO3 with a high ratio of length to diameter (aspect ratio) is widely used in plastics, rubber and ceramics as a filler and in pigments and paints as a carrier. This paper investigated the influence of H3PO4 dosage, reaction temperature, CO2 flow rate, and initial Ca(OH)2 concentration on formation of needlelike aragonite CaCO3. It was found that the presence of H3PO4 in Ca(OH)2 suspension resulted in rapid formation of (Ca5(PO4)3(OH)) crystal nuclei, which facilitated nucleation and growth of aragonite CaCO3 on the formed (Ca5(PO4)3(OH)) crystal surfaces. The results revealed that H3PO4 addition of P/Ca of 0. 2~0. 3, high temperature of 75~85 °C, low CO2 flow rate and initial Ca(OH)2 solid concentration of 1. 5 %~5. 6 % are beneficial to formation of aragonite. Well crystallized needlelike aragonite CaCO3 whiskers with length > 20 µm and aspect ratio > 15 were directly synthesized.

Jan 1, 2014

By R. W. Drier

THE conductivity of copper wire is of prime importance to the electrical industry and consequently to the copper refiner and wire manufacturer. Annealed copper wire has a higher conductivity than hard-drawn wire, but, on the other hand, its tensile strength is lower. In an attempt to explain the reasons for these changes in property or at least to study the conditions existing in these two types of copper wire, the experiments described here were carried on in the Department of Metallurgy of the Michigan College of Mining and Technology. This is only a partial and preliminary report on some of the work done to date on a research program of which the object is an intensive study of copper. It is offered with the hope that, though it is not an exposition of the most rigorous of conclusions, the general trend of inferences which may be drawn will be of value and interest.

Jan 1, 1929

By H. M. Howe

Page 1. Introduction............................514 2. Definitions.............................517 3. Brevity of the Heating........................517 I. THE HARDENING OF THE BORE..............517 4. The Hardening of the Bore.....................517 5. The Thickness of the Hardened Layer.................517 6. Martensitization..........................518 7. The Hardening Repetitive ......................519 8. The Temperature Cycle.......................519 9. The Hardened Layer is the Merged Layer............... 521 10. The Progressiveness of Merging....................521 11. The Progressive Thickening of the Hardened Layer from Round to Round. 523 12. Merging and Hardening are Cumulative................523 13. Three Additional Causes of the Progressive Thickening of the Hardened Layer 525 14. Progressive Roughening of the Bore..................525 15. Avoidance of an Endothermic Transformation.............525 16. Asymptotic Retardation of the Thickening of the Hardened Layer.....527 17. The Troostitic Layer........................ 529 18. The Usual Lack of Martensitic Markings................529 19. The Thickness of the Hardened Layer Should Increase with the Quantity of Heat Taken up by the Walls of the Bore.................530 20. The Decrease of the Thickness of the Hardened Layer from Breech to Muzsle 531 21. Phstic Deformation as a Contributory aCause of Hardening........531 22. In What Way May Plastic Deformation Hasten Hardening?....... 535 23. Possible Need of Coarsening.....................535 24. Carburization as a Cause of Hardening..........:.....536 25. Does Hardening Increase Erosion?..................-538 11. THE CRACKING OF THE BORE ...............539 26. Appearance of the Bore and Cracks in Elevation............539 27. The Cracks in Elevation in the Rear Ring...............539 28. The Cracks in Elevation in the Forward Ring.............540 29. The Copper Network in the Grooves.................540 30. The Cracking of the Lands......................541

Jan 1, 1918

By D. F. Malan, J. C. Esterhuyse

In this study we explore the use of a novel numerical modelling approach to study the effect of pillar reinforcement on pillar stability. Case studies in the literature indicate that tendons, strapping of the pillars, and shotcrete or thin spray-on liners are commonly used to reinforce pillars. No clear methodology exists to select the type of support or to design the capacity of the support required, however. This has led to ongoing collapses in some mines in spite of heavy support being used to reinforce unstable pillars. A limit equilibrium model with confinement on the edge of the pillar was used to simulate the interaction of the support with the failing pillar. The model correctly predicts that an increase in confinement will lead to a decrease in the extent of pillar failure. As the displacement discontinuity boundary element method allows for the efficient solution of largescale bord-and-pillar layouts, the effect of pillar confinement can now be studied on a mine-wide scale. Accurate calibration of the limit equilibrium model is, however, required before this method can be used for the design of effective pillar support.

May 3, 2023

By Bill S. Taylor

Dutch State Mines [D.S.M] introduced the Heavy Medium Cyclone into the United States for cleaning fine coal about three decades ago. Since that time the general industry practice has been to deslime the raw coal at 28 Mesh (0. 59mm) size. The plus 28M material is fed to the Heavy Medium Cyclone for cleaning, and the 28M x 0 fraction is processed by other means (e. g. flotation or hydrocyclones). This approach recognized that 28M was the smallest size particle that could be easily rinsed on vibratory screens without excessive loss of magnetite, and without blinding of sieve bend and vibratory screen decks. Another reason for the 28M de-sliming was to avoid excessive contamination of the media with non-magnetic coal, shale, or clay fines. The most undesirable of these contaminants is the sub-micron size clay particles (2) that greatly increase the viscosity of the media and reduce the numerical maximum level that the media specific gravity can obtain due to the lower specific gravity of clay with respect to magnetite. The higher the fugitive clay content, the more severe the preceding problems become. During the last 30 years, many conventional Heavy Medium Cyclone Plants have been built throughout the world. In the United States, the initial cyclone plants were confined to the production of high quality metallurgical coal where lower gravities of separation were required than could be obtained from the conventional hydraulic or air separation processes. In recent years a large and ever-increasing number of preparation plants producing steam coal have started utilizing Heavy Medium Cyclone technology due to the environmental pressures being encountered to produce low sulphur coal. Due to the inherent characteristic of many coals of having a lower pyritic sulphur content at lower specific gravity fractions, many applications and markets are appearing for separating steam coals at much lower specific gravities than have been historically normal in the United States. Therefore. Heavy Medium Cyclones are being utilized to a much greater degree in this field, due to the flexibility of low separating gravity ability coupled with high efficiency when high percentage of near gravity material is present.

Jan 1, 1978

Physical testing of rock support for rockbursting conditions has been carried out for over 40 years. A review of this testing shows that it has been mostly component?based, rather than actually testing support systems. Further, it is concluded that none of the testing is truly representative of rockburst loading in a similitude sense. Similitude conditions are not achievable, mainly because the real conditions in a rockburst event, such as seismic source location and magnitude, wave frequencies, amplitudes, and interactions, are not all known. Because such information is not available, and because the results of all testing carried out to date have not been able to define, for support design purposes, the capacity of support systems, ongoing physical testing of rockburst support systems is essential. It is essential that the test should simulate, or actually take place in, a supported rock excavation. A rock support system is a combination of individual support components that work together to retain and contain the rock. In doing this, the components are subjected to loading by the rock and to interactive loading between one component and another. It is necessary to prove the capacity of such rockburst support systems by subjecting them to severe loading, as in direct blasting. The direct blasting approach, pioneered more than 40 years ago, probably still provides the greatest validity as a significant test of rockburst support capabilities, even though it does not simulate a rockburst. Direct blast testing of rockburst support systems in a surface environment, such as in a quarry or on exposed rock cutting surfaces, could represent a practical development of the approach, facilitating the execution and monitoring of tests.

Jan 1, 2012

By Jim Richards, Eli Choueiry, Brett Robinson, Amanda Elioff

The Los Angeles Metro Gold Line Eastside Extension (MGLEE) extends Metro’s light rail system to the densely populated and growing East Los Angeles communities. Much of the 6 mile alignment consists of at-grade track, but the project also features a1.7 mile underground segment in cut-and-cover and twin-bored tunnel structures. In light of past experiences with open shield construction, The Metropolitan Transportation Authority (Metro) specified, for the first time, use of Pressure Face Tunnel Boring Machines (TBM’s) to advance tunnels through soft ground. This paper describes the history of the tunnel design, construction management, and construction methods adopted that resulted in successfully completing the tunneling segment.

Jan 1, 2007

By T. Chmielewski

Unique mineralogical and petrological properties of black shale in the copper ore deposit of the Foresudetic Monocline (SW Poland) resulting from three lithological layers have been described in terms of its unfavorable behavior in the ore processing circuits. A concept of processing of a part of the black shale fraction from the flotation circuit of the concentrating plant by separating a by-product enriched in the shale matter was presented. This by-product represents the tailings of the first cleaning flotation and, as a hard-to-treat circulating middlings, overload the cleaning operation in the flotation circuit. It was found that the investigated by-product cannot be effectively up-graded using standard xanthate flotation. This is due to a fine dissemination of sulfide minerals in the dolomitic and clay shale particles significantly enriched in organic carbon. The content of the organic carbon is similar to that in the petrographically "pure" black shales. After a comprehensive examination of the shale by-product it was recognized that the investigated middlings can be regarded as a specific shale concentrate for individual processing. The effect of non-oxidative leaching of middlings with sulfuric acid on their further flotation was presented. It was shown that non-oxidative leaching is a selective process, in which calcium and magnesium carbonates decomposition leads to effective liberation of sulfide minerals which were finely disseminated in the hydrophilic carbonate gangue. Leaching of the flotation feed with sulfuric acid selectively decomposes carbonate minerals and consequently enhances flotation results. Saturation of leaching slurry with gaseous carbon dioxide favorably creates non-oxidative conditions and leads to a great decrease of the electrochemical potential of sulfide particles as well as hinders their solubilization. Partial carbonates leaching from middlings resulted in evident liberation of valuable minerals. Consequently, it resulted in an increase of both recovery and grade of concentrates obtained by flotation of shale by-product after non-oxidative leaching.

Jan 1, 2014

By R. Menge, N. Basin, M. Sibony, J. Lecadet, S. Schmidt

In 1996, Metaleurop replaced its conventional sintering and blast furnace lead smelting activity in Nordenham, Germany by Sirosmelt/Ausmelt technology. Following some alterations to the process and the equipment, the bath smelting plant reached its design capacity for the treatment of lead concentrates, lead sulphate paste from spent batteries, secondaries and internal by-products. A reliable metallurgical process has been established, and thus higher process stability has been achieved, increasing simultaneously the refractory life. Nevertheless, improvements are needed to control the process with a better automation system and reliable expert-systems, because of the intensity of the smelting process. The introduction of the Sirosmelt process for the pyrometallurgical production of lead instead of the prior conventional process has also demonstrated the following advantages: reduced emissions of heavy metals and gaseous compounds, reduction of the specific energy consumption, minimization of residues and a reduction of staff and maintenance costs. The environmental performance of the plant meets the requirements of the German regulations.

Jan 1, 2000

By John Durkin

A system based on seismic techniques has been developed to detect and locate men trapped underground following a mine disaster. Both theoretical and field studies have been used to generate models to predict the performance of the system. For a strong source, it is almost certain that the miner's signal will be detected if the geophone array can be positioned over a likely area of entrapment. After signal processing, it is highly likely that the location of the miner can be determined within an accuracy of 100 ft (30.5 m). The system is presently operational in a state of readiness in the event of a mine disaster.

Jan 1, 1980

By Gordon R. Sima

This contract is concerned with the construction of a Time Resolved Audio Dosimeter System consisting of one readout unit and several dosimeter units. The Time Resolved Audio Dosimeter System was designed and developed by the Bureau of Mines with the purpose of this contract aimed at obtaining additional units for further field testing and evaluation. All construction was in accordance with the Bureau of Mines design and/or Bureau approved drawings produced during the course of this contract. This report contains a summary of the construction efforts, problems encountered, recommendations and all drawings produced under this contract.

Jan 1, 1977

By David L. Kuck

Siderophyle platinum-group metals and sane gold are a thousand times more abundant in metal and chondritic meteorites than in terrestrial or lunar rocks. Type I and II carbonaceous chondrites contain granules of the high boiling point metals W, Re, Mo, Ir and Os. Metal meteorites and the metal fractions of other chondrites contain siderophyle Pt, Pd, Ru, Rh, Os, Ir and Au. Spectra of sunlight reflected from asteroids, when compared with those of meteorites and specific minerals, provide a rough classification and guide to sources of precious platin-group metals.

Jan 1, 1982