Search Documents

Plant-Based Trials of Monitoring of Coal Flotation Systems Using Electrical Impedance Spectrum Technique

Sep 13, 2010

By Charles C. Boley

Using bench-and pilot-scale coking facilities, the Bureau of Mines produced experimental coke from blends of char with Sunnyside coal (high-volatile A bituminous) from Carbon County, Utah. At bench scale, additions of char made from lignite improved resultant cokes when concentrations of up to 60 pct were used in the blends. At pilot scale (500-pound movable-wall oven), four chars made by entrained-bed carbonization techniques from the parent Sunnyside coal and from a North Dakota lignite were used in two-component blends with the Sunnsyide coal. Chars from Sunnyside coal had volatile matter contents of 5.8, 9.8, and 16.0 pct, moisture-free basis; the char from the lignite had 16.6 pct. In twenty-five 500-pound tests, improvement in coke quality was observed from all blends at char concentrations to 17.5 pct. The best coke, produced from a concentration of 12.5 to 15 pct of S.8-pct volatile char, exhibited physical properties approaching those of an industrial coke produced from Sunnyside coal blended with three higher rank blending coals. Studies were also made of the effects on coke quality of char source, of particle size, of comparative use of char and of a blending coal, and of prolonged coal storage.

Jan 1, 1973

By Shu-cai Zhou

"To understand the solidification behavior of austenitic heat-resistant stainless steel (TP34 7) in rotary electromagnetic-field, the influence of electromagnetic stirring in mold (M-EMS) on solidification structure of TP34 7 heat resistant steel in a round billet continuous casting was investigated based on industrial experiments. The results indicate that the excellent billet solidification structure of TP34 7 heat resistant steel can be obtained with appropriate electromagnetic stirring parameters. The solidification structure of TP34 7 heat resistant steel can be remarkably refmed, central porosity and shrinkage cavity can be remarkably decreased and equiaxed grains zone widens was enlarged. The industrial trials verify that the stirring intensity of TP34 7 heat resistant austenitic stainless steel should be higher comparing with plain carbon steel. Due to a higher viscosity, rotating speed of molten stainless steel was 20-30% lower than that of molten carbon steel in the same magnetic flux density.IntroductionIn recent years, the development of ultra super critical (USC) plants is accelerated by the demands of environment protection and energy saving, and USC plants with steam temperature and pressure conditions in excess of 593°C and 24.lMPa respectively were constructed. To achieve the goal, it is important to develop new materials with excellent high temperature strength, superior resistance to oxidation and corrosion at high temperature. Besides, their cost must be low enough to meet the requirement of plants [ 1]. TP34 7H steel is promising austenitic heat-resistant steel, which is used as superheater/reheater tube material and is extensively used for high temperature components and fossil-fired power plants, and suitable to be used in USC boilers plant. This kind steel contains with about 0. 7%Nb and it keeps higher allowable stress and creep rupture strength than TP304 and TP321H [1-2]. TP347H has conventionally been produced by ingot casting followed by forging and rolling. Recently, in order to decrease the production cost, challenging trials to produce these types of alloys by a continuous casting (CC) process have been attempted. However, the solidification structure of austenitic stainless steel is one of the key issues that attract more attention. Due to the low thermal conductivity of TP347H heat resistant stainless steel (much smaller than that of plain carbon steel), pronounced defects during continuous casting of austenitic heat-resistant steel such as coarse columnar, center porosity and coarse bridging, greatly influence mechanical properties of fmished products.A widely used technique in metallurgy is the inductive drive of molten metals using rotational or traveling magnetic fields. Recently, rotary electromagnetic stirring (EMS) has been applied to reducing various defects and improving increase the solidification structure of the metals in the continuous casting of steel, Al-based alloys and Mg-based alloys [3-8]. Electromagnetic stirring of plain carbon and low alloy steel in the continuous casting bloom and slab is well established for improving the quality of cast products [9-11] and is widely used in industry. However, very few literatures on electromagnetic casting of heat resistant stainless steel have reported. In this work, an industrial plant trial was performed to clarify the effect ofM-EMS on the macroscopic quality ofTP347heat resistant steel billet, in which the regularity and mechanism of the influence of EMS on solidification casting billet were discussed."

Jan 1, 2014

By R. A. Seitz

Although the role of the collector has long been thought to play a predominant role in coal flotation, recent investigations by the authors show that the frother plays an equally important role. These investigations have included extensive testwork in several coal preparation plants and in the laboratory. The factors which were investigated include the absolute level of collector and frother addition, the ratio of frother to collector additions, the type of frother, and the particle size distribution of the feed. Results from this testwork reveal strong interactions between these factors as well as the necessity of considering these factors in order to optimize the reagent regime.

Jan 1, 1987

By Victor E. Archer

INTRODUCTION Man is exposed to many agents which induce mutations in germ cells and/or cancer at work, at play, and at home. In this total mix of mutagenic and carcinogenic agents, how important are radon and its daughters? Before man moved into caves and other permanent dwellings, the principal mutagenic and carcinogenic agent to which he was exposed was natural background radiation--cosmic rays, radium and potassium-40 in his food, plus gamma rays and radon from the soil and rocks. When man moved into caves, captured fire, and began to preserve and store foods, his exposure to carcinogens and mutagens took a quantum leap. Carcinogens and mutagens appear to act in the same way, that is, by altering the DNA or nuclear proteins of cells. Most mutagens are carcinogens, and vice versa, so when I say mutagens from here on, I will be referring to both. The relationship of the two is emphasized by the fact that administration of a carcinogen to a group of animals not only increases cancer rates among the exposed animals, but also among their progeny (Tomatis 1979). Environmental Mutagens Smoke from man's fires, overheated foods, and foods preserved by smoking, resulted in ingestion and inhalation of many polycyclic aromatic hydrocarbons--many of which are mutagens. Caves and houses with tight windows and doors tend to collect the radon which is constantly emanating out of soil, rocks and concrete, so man's exposure to the radon daughter component of background radiation increased several fold. Preserving food by salting or pickling with material that contained nitrites and nitrates led to increased ingestion of nitrosamines, which are potent mutagens. When his grains and other foods were stored in slightly damp rooms, fungi or mold would grow on them. Several of these fungi are now known to produce very potent mutagens. The best known of these is aflatoxin B (Ramachandra 1979). It may seem strange that a living organism would produce a mutagen. One might think that it would scramble its own genetic heritage. The reason it does not is that it produces the mutagen in an inactive form. It can be activated only by an animal's enzyme systems after being eaten. When man moved into cities, the collective smoke from wood and coal fires further increased his exposure. That particular smoke has now mostly disappeared, but has been replaced by smoke from automobiles and industry. When man moved into the age of technology, his exposure to mutagens again increased dramatically. Many mutagenic chemicals, from benzene and beta naphthylamine to a long array of pesticides and tobacco products have been added to our environment. Excess deaths from cancer are now being observed among chemists in most industrialized nations. Mutagens are even found in much of our wine, beer, and whiskey (Keller 1980). Some of the chemical mutagens were widely used in food or in other commercial products before their potential was discovered. Striking examples of this is the original butter coloring agent and the polychlorinated biphenyls that have been widely used in brake fluids and electrical transformers. Large quantities of them have been discarded or disposed of in a careless manner--in such a way that many of them have contaminated our food, our ground water and air (Landrigan 1981). In this nation, with the help of several recent laws, we were just beginning to get control of the industrial chemical mutagens. With the relaxing of these laws that is currently going on, it appears that it will be many more years before we really bring chemical mutagens under control. Many nations have yet to come to grips with this problem. On top of this massive array of chemical mutagens we have now added radiation from many artificial sources. For most of us this means medical X-ray and fallout from nuclear weapons testing. Ionizing radiation is one of the most potent mutagens, so it has caught the public eye, and its contribution cannot be ignored. Fortunately, by the time we started using radioactive materials in quantity with the Manhattan Project, we had experience with radium and X-ray (some of it bad); we knew enough radiobiology and enough about methods of radiation protection so that most nuclear laboratories have had a phenomenal record of radiation safety. Radiation is one new technology with great potential for harm that has not exhibited that potential except for a few isolated situations like that of radium dial painters, uranium miners and atomic bomb victims. Uranium miners slipped into this list almost by accident. We could have protected our uranium miners just as well as we did the workers in nuclear laboratories; but we failed to do so. Why didn't we? The reason is simple. The Atomic Energy Commission was charged with protecting the health of their workers. They did not wait for a pile of bodies before they introduced controls. Congress appropriated the money, and taxpayers were willing to pay for the protection against radiation. Miners unfortunately did not work for the Atomic Energy Commission. Although mine operators were ignorant about radiation, the key item was that in the 1950s nobody was willing to pay the extra costs of adequate ventilation to control the high levels of radon and radon daughters in uranium mines. Control was not achieved until new laws and regulations were passed which made it compulsory. BIRTH DEFECTS AND CANCER

Jan 1, 1981

By Michael P. Moore, Christopher J. Rise

"Over the past twenty years, there have been numerous studies which have attempted to correlate the prevalence of Coal Workers' Pneumoconiosis (CWP) with different characteristics of the coal seam. Some investigators have tried to find a relationship, or the lack of a relationship, between the rank of coal seams and the incidence of CWP. Others have attempted to show that there is a positive correlation between the mean mass of respirable dust in the mine atmosphere and the prevalence of CWP. Still others have tried to determine the influence of the quartz content of respirable dust on the incidence of CWP. Unfortunately, many of these different investigations have conflicting conclusions.One area of research with conflicting conclusions deals with the relationship between the rank of the coal and the incidence of CWP. For example, an inves¬tigation conducted in Pennsylvania and West Virginia coal mines concluded that the prevalence of CWP increases with an increase in coal rank (1). A study in Great Britain also observed a close relationship between the rank of coal and the prevalence of CWP (2). However, another study involving 312 Appalachian coal miners concluded that the association between coal rank and CWP might be fortuitous and that other factors may be more important (3). In addition, an investigation involving 2,600 miners during a period of twenty years in Great Britain established that there is only a weak correlation between the prevalence of CWP and the rank of the coal (4). Consequently, it appears that there is still uncertainty as to whether or not the rank of the coal seam has an influence on the development of CWP.Another area of investigation concerns the relationship between the mean mass of respirable dust present in the mine atmosphere and the prevalence of CWP. A study involving 4,122 miners over a period of ten years in Great Britain noted a high correlation between the mean mass of respirable dust and the incidence of CWP (5). Another investigation involving 3,154 British face workers con¬cluded that the overall mass of respirable dust is the factor most closely related to the ten-year attack rate of CWP (6). However, a study conducted in thirty-one mines in the United States concluded that it is doubtful that the quantity of respirable dust alone is responsible for the difference in the prevalence of CWP (7). Even though there are conflicting conclusions, there are many more investigators who confirm, rather than deny, the relationship between the mean mass of respirable dust and the development of CWP.The third subject of investigation is the role of quartz in the incidence of CWP. For example, two studies in Great Britain concluded that the quartz content in coal mine dust has no relationship to the prevalence of CWP (8,9). But a study involving 312 Appalachian coal miners revealed that the level of exposure to free silica plays an important role in the development of CWP (10). Once again, the conclusions reached by different researchers are conflicting.Probably the most important factor in the discrepancy among the studies is the variability among different coal mines. A mine operating in an inherently ""dusty"" seam may have a low concentration of respirable dust while a mine operating in a less dusty seam may have a high concentration of respirable dust. This discrepancy is a result of variables such as the effectiveness of ventilation or the efficiency of the water sprays. Consequently, it is very difficult to compare the dustiness of different coal seams by in-mine measurements of the respirable dust concentration. A laboratory test would more accurately characterize a coal seam according to its respirable dust production."

Jan 1, 1988

By Manchao He, Xiaoding Xu, Yubing Gao

Based on the geological conditions of the 15,600 working face in Pingba Mine, this paper establishes the mechanical model of the stress distribution in the pre-working face under the influence of mining pressure based on a hemispherical stress distribution theory. The analytical formula for the stress distribution is determined. A numerical model for the mining pressure under the influence of key layer is also constructed, and dynamic stress interruptions under various roof-cutting relief schemes in different horizontal positions are simulated. The stress distribution of the stope under different pressure relief schemes is analyzed and compared with the theoretical results. Results show that blasting roof cutting blocks the transmission of the abutment pressure to the working surface to the coal and rock mass in front of the working face, reducing the significant working face mining pressure influence range, which decreases as blasting pressure relief position moves toward the working face. Stress accumulation in the coal in front of the working face also increases as the blasting pressure relief position moves toward the working surface. Engineering practice results show that blasting cutting can effectively block the propagation of mining pressure, and the stress impact range is shortened by approximately 1/3.

Jul 31, 2021

By Tácio Ferreira, Liz Diaz

Capstone Copper’s Pinto Valley Mine faced challenges in recovering rock and ore on final walls because of geotechnical constraints that require restrictions on methods for loading blastholes adjacent to the pit boundaries to preserve wall stability. The operation had been using the same drill-and-blast designs for years. With changing geology, such as harder rock, as mining progressed, material was being left unmined in final walls because of poor breakage. The amount of unrecovered, unprocessed ore was estimated at 345 kt/a (380,000 stpy) generated from an average of 60 final wall blasts performed annually. The engineering team from Capstone and Dyno Nobel engaged to minimize the amount of material left on the final pit walls. This article presents how data were collected and design standards reviewed, and the opportunities that were found to improve ore recovery from pit final walls without increasing drilling and blasting costs. The results collected from implementing the new design on two benches showed the potential for extra revenue of approximately $3.6 million generated annually from reducing final wall unrecoverable underbreak by nearly 71 percent on the mine’s highwalls.

Aug 1, 2025

By D. W. Levinson, L. F. Mondolfo, N. A. Gjostein

MANY investigations are reported in the literature on the age hardening of Al-Mg-Zn alloys but most of them are concerned mainly with mechanical property changes. The present investigation was started to determine the structural changes in an AlMgZn alloy. The alloy composition was chosen in the existing phase diagram" so as to lie on the quasi-binary section Al-(AlZn)Mg Actually, it was found that the diagram as published was inexact at the lower temperatures and that the phase in equilibrium with aluminum at the lower temperatures is not the ternary compound. Technique The alloy used for the investigation was prepared from high purity materials and the resulting composition as determined by chemical and spectro-graphic analysis was: Zn, 6.17 pct; Mg, 2.13 pct; CU, 0.03 pct; Si, 0.009 pct; Fe, 0.005 pct; and the remainder, aluminum. An ingot -in. thick was cast, homogenized, hot and cold-rolled to strip 0.064-in. thick for dilato-metric and powder work, and to foil 0.005-in. thick for single crystal work. Solution treatment temperature for all specimens was 475°±5°C for periods of at least 1 hr, either in air furnaces or lead baths. Aging was done in oil or Pb-Bi baths controlled to within ±3°C. The aging was investigated at the following temperatures: room (30°), 130°, ZOO0, 260°, and 300°C. For the dilatometric study, the length changes were measured continuously, at temperature, using strips of alloy 10 in. long, shaped as channels to eliminate undesirable deflection due to bending. To compensate for thermal expansion and contraction due to the variations in the temperature of the aging baths, the dilatometers were built of the same alloy as the one being tested, with the same shape and size, but with material fully annealed. Gages on which 0.0005 in. could be read and 0.0001 in. estimated were used to measure the dilation. Length changes were also measured at room temperature. Strips approximately 10 in. long were solution-treated, quenched, and measured in a supermicrome-ter in which 0.0001 in. could be read and 0.00001 in. estimated. The specimens were immediately aged for a given time, remeasured, and then the cycle was repeated, including the solution treatment. The error of measurement with this technique was somewhat larger, but the results confirmed those obtained by continuous measurements. The sheet used for the dilatometric work was checked to determine grain orientation. Both X-rays and etching methods revealed a rather coarse grain size but only a negligible amount of preferred orientation. Thus, volume changes calculated from length changes are not invalidated by preferential orientation effects. Pieces of the sheet used for the dilatometric work were also used for the metal -lographic work. Filings for the powder X-ray study were produced from a homogenized piece of sheet. These filings were magnetically purged of iron, screened to 200 mesh, sealed in a Pyrex tube containing an argon atmosphere, and solution-treated. When quenching, the glass tube was broken, so that the powder dropped directly into cold water. After drying with alcohol, the powder was sealed into capillary tubes containing an argon atmosphere and then aged for the required times. In spite of all these precautions the three strongest lines of a( Al2o) appeared in all patterns, and were used as internal standards. By the use of these standards, accurate corrections for film shrinkage were obtained. For the back reflection patterns, annealed nickel powder was mixed with the specimen to act as internal standard. A preliminary investigation was made in small (57.3 mm diam) powder cameras. From these patterns the changes which took place in the solid-

Jan 1, 1957

By Liz Diaz, Tacio Ferreira

Capstone Copper’s Pinto Valley Mine faced challenges in recovering rock and ore on final walls because of geotechnical constraints that require restrictions on methods for loading blastholes adjacent to the pit boundaries to preserve wall stability. The operation had been using the same drill and blast designs for years. With changing geology, such as harder rock, as mining progressed, material was being left unmined in final walls because of poor breakage. The amount of unrecovered, unprocessed ore was estimated at approximately 380,000 tons a year generated from an average of 60 final wall blasts performed annually. The engineering team from Capstone and Dyno Nobel engaged to minimize the amount of material left on the final pit walls. This paper presents how we collected data, reviewed design standards, and found opportunities to improve ore recovery from pit final walls without increasing drilling and blasting costs. The results collected from implementing the new design on two benches showed the potential for extra revenue of approximately $3.6 million generated annually from reducing final wall unrecoverable underbreak by nearly 71% on the mine’s highwalls.

Feb 1, 2025

"Bay d'Espoir is in the approximate center of the south coast of Newfoundland. The geology of the area can most conveniently be considered in terms of three units: (1) an Ordovician or older polydeformed terrain termed the Little Passage Gneisses; (2) a Lower-Middle Ordovician volcano-sedimentary sequence assigned to the Baie d'Espoir Group; and (3) granitoid intrusive rocks of mid-Paleozoic age. Mineralizing events accompanied the formation of the latter two units.The Baie d'Espoir Group comprises a dominantly sedimentary sequence of pre-Middle Ordovician shelf and distal turbidite sediments deposited on the eastern margin of Iapetus. A significant volcanic component is, however, present in the Isle Galet Formation, consisting of up to 30% felsic volcanic rocks interbedded with sedimentary and epiclastic rocks. The Isle Galet Formation hosts several disseminated to thinly bedded Pb-Zn-Ag occurrences associated with altered felsic tuff and graphitic shale. They occasionally grade laterally into pyrite iron formation and appear to have been deposited in a very distal volcanic environment. The Isle Galet Formation is a time equivalent of the mineralized pre-Caradocian island-arc sequences of central Newfoundland, but differs from them both in style of volcanism and in the nature of the associated mineral deposits. It is, however, comparable in many respects to mineralized volcanic sequences in the La Poile Bay area of southwestern Newfoundland.Mineralization associated with granitoid rocks in Bay d'Espoir is best developed around the southeast margin of the North Bay Granite, where two-mica leucogranite forms a marginal phase. Numerous minor base metal showings occupy quartz, quartz-carbonate and barite veins in the adjacent sedimentary rocks. Collectively, the showings exhibit a well-developed, zonal pattern around the granite margin; molybdenite (±py, cpy) predominates near the contact, giving way outward to galena (±sph, py, asp, cpy) and eventually to stibnite (±asp, py) at the periphery. Mineralization associated with granites in similar settings elsewhere in southern Newfoundland includes tungsten in the Grey River and Granite Lake areas and molybdenite in the Rencontre Lake area."

Jan 1, 1982

By Winton Gale

"The aim of this paper is to summarise the results and conclusions of Australian Coal Association Research Project (ACARP) Report Cl3013 which relate to water inflows into a mine which occur through the overburden above and adjacent to longwall panels. The study assessed available data of inflows into underground coal mines and utilised computer simulation of water flow through fracture networks. The study concluded that flow into mines is typically via an interconnected network of pre-existing and mining induced fractures. The height above the coal seam that mining induced fractures extend is typically related to the width of the panel. However the potential for those fractures to form a connected network which can facilitate flow, is related to the amount of subsidence and the depth of mining. The study compares model simulations with measured data and provides guidelines to estimate the average hydraulic conductivity of the overburden above extracted longwall panels in Australia.INTRODUCTIONWater inflow into coal mines has been a design issue for many years. Guidelines as to the potential for water inflow have been developed in many countries based on local experience and the form of mining being undertaken. In most instances, the guidelines relate to inflows which would endanger underground personnel and operations.In more recent times, water inflow criteria for mines has been widened to include lesser inflows which may not impact on mine safety or operations, but have the potential to reduce water flow within streams and surface aquifers. For the purpose of this paper the larger inflows which are readily measured in a mine or may impact on mining safety are defined as mine inflow and the lesser inflow relating to aquifer water loss as environmental inflow.The water losses referred to are those which enter the mine from the surface or from near surface aquifers.The empirical relationships developed as mine design guidelines or regulations typically relate to high flow (mine inflow) situations and in this paper, these have been reviewed as to their application to environmental inflow. In many cases environmental inflows were unlikely to have been noted or recorded in many mining operations in the past."

Jan 1, 2010

By Mehdi Noori, Atefeh Azizitorghabeh, Fereshteh Rashchi, Ataollah Babakhani, Sarah Mahmoudi

The focus of this research was to evaluate the synergistic effect of bis(2,4,4-trimethylpentyl) phosphinic acid (CYANEX 272) and di-(2-ethylhexyl) phosphoric acid (D2EHPA), diluted in kerosene, on the extraction and separation of Co(II) and Li(I) from synthetic sulfate solution. The results indicated that using a mixture of CYANEX 272 and D2EHPA was efficient in extracting and separating Co(II) from Li(I). The optimum ratio of CYANEX 272/D2EHPA was found to be 5:1, in which the highest separation factor was obtained (5973.23), and ΔpH0.5 was 4.10. Adding tributyl phosphate (TBP) as a modifier and increasing the temperature improved the metals’ separation rate and extraction efficiency. Thermodynamic studies were also carried out, and ΔH, ΔS, and ΔG values were computed, revealing the endothermic nature of Co(II) and Li(I) extraction by CYANEX 272/D2EHPA mixture. The conducted experiments for the McCabe–Thiele diagram showed the possibility of using two stages to extract over 99% of Co(II) and Li(I). Slope analysis and Fourier transform infrared spectroscopy (FT-IR) were employed to comprehend the Co(II) and Li(I) extraction mechanism using a mixture of CYANEX 272 and D2EHPA.

Jan 17, 2022

By J. L. Llanca

The New Level Mine project (NLMP), the planned underground expansion of the El Teniente mine in Rancagua, Chile, is expected to reach a daily extraction rate of 137 to 180 ktpd upon achieving full capacity. Production is planned to start in the year 2017 and the current plan is to meet that target through two development phases, from the year 2012 to 2014 and from the year 2015 to 2017. To achieve the 2012 to 2014 underground development schedule, the ventilation requirements have been estimated in the range of 189 m3/s (400 kcfm), and cannot be made available without significant modifications to the current system of El Teniente. As a result, a certain number of alternatives were explored to find a solution to this shortfall, for example, adding raises to generate parallel airways and installing fans to reinforce the current ventilation system. From the alternatives studied, the installation of a second main fan (system) in parallel to an existing one was identified as the best solution, and selected for implementation, however the location was not ideal and there were concerns as to the operation of both fans once the second fan was installed. This paper presents the study used to estimate the operational points of both the current and the new fan, and to justify the parallel installation of the additional main fan. An additional computational fluid dynamics study was undertaken to validate the operational point, given the particular geometry of the fan?s location and placement, to guarantee a stable operation of the fans. Finally, the protocols arising out of this work for starting the fans, and operating them in parallel to avoid generating a stall condition and damaging the investment are discussed.

Aug 1, 2013

By R. W. Raymond

Recent literary labors have led me to the compilation of the following tables and estimates, which may possess interest for my colleagues in the Institute, and which are here submitted without comment.

By S K. Michelic, N Preisser

For certain applications, steels have to feature a very distinct and well-defined level of cleanness in terms of the number and composition of non-metallic inclusions. Therefore, one crucial aspect of steelmaking is removing and controlling said non-metallic inclusions during the process. Particle removal during ladle refining comprises three stages, namely: 1. Flotation 2. Transport through the steel/slag interface 3. Dissolution of the particle in the slag. Only if all three stages are completed the particle can be considered as fully removed from the steel melt which, in turn, leads to the slag being one of the most influential parameters for inclusion removal and control. Depending on the composition of the particles and the slag, the dissolution can be controlled by different mechanisms. This study focuses on the diffusion-controlled dissolution of solid oxidic particles in slags. For this, a model of particle dissolution has been developed. For modelling diffusion, either the differential equation following Fick’s second law can be solved, or an analytical solution to this equation valid for stationary interfaces can be used. Both approaches allow for calculations of concentration profiles of the dissolving species in surrounding slag. From this, the mass flux can be derived, which finally leads to calculating the boundary layer velocity due to considerations of mass balance. In this work, both methods as well as results of dissolution experiments using High Temperature Confocal Scanning Laser Microscopy are compared. This research aims to provide a framework for diffusion-based dissolution modelling in further expanding the understanding of particle dissolution in secondary metallurgy.

Aug 21, 2024

By David R. Peterson

This user's manual covers a set of 5 computer codes which were generated during development of a simulation of deep ocean mining operational economics. Table 1.1 provides a summary of these codes, and a more thorough description of each follows, In addition to the descriptions in this user's manual, internal documentation is provided throughout each code, except for the very simple ones, for ease of understanding or possible modification. The two major codes are MINER, which performs the deep ocean mining system operational simulation, and MSWEEP, which calculates the sweep and feed efficiencies for a set of collector paths generated by MINER. The standard operating procedure is to input the system and operating parameters to MINER, which computes a set of collector paths automatically and stores the information in the fife PATH.DAT. MSWEEP subsequently retrieves the collector path data in PATH.DAT, and uses it to calculate sweep and feed efficiency. Separating MINER and MSWEEP allows parmetric execution of MSWEEP without recomputing the collector paths with MINER. PIPEST, RESP, and OBSTCL are special-purpose codes described in more detail in the following documentation.

Jan 1, 1979

By G. S. Rice, Clark H. H.

When mines in the interior coal fields of the United States began the practice of blasting the coal without undercutting, or what is known as…

Jan 1, 1915

By J Masliyah, Z Xu

The largest oil sand deposit in the world is located in Alberta, Canada, with a total proven reserve of 2.5 trillion barrels of oil. The water based extraction process is currently being used in commercial operations to recover bitumen by flotation from oil sand ores. A recognised challenge in bitumen extraction is the reduced bitumen recovery when processing ores containing high fines content or æweatheredÆ oil sand ores, collectively known as poor processing ores. Inspired by demonstrated success of using kerosene as collectors in coal flotation, an innovative idea of using oily bubbles (air bubbles coated with a thin layer of oil or solvent) was tested to improve bitumen flotation recovery from poor processing ores. In this study, dynamic contact angle of air bubbles or oily bubbles on bitumen and induction time of bitumen-oily bubble attachment in water were measured to justify the use of oily bubbles in bitumen recovery from poor processing ores. The type of oil or solvents, including kerosene, toluene and naphtha, used in generating oily bubbles showed a marginal effect on the contact angle values, similar to the values measured with air bubbles. However, the spreading of an air bubble was found to be much slower than that of oily bubbles on a bitumen surface. The induction time for oily bubble-bitumen attachment was found to be much shorter than that for corresponding air bubble-bitumen attachment in the process water from poor processing ores. The reduced induction time for kerosene-coated air bubble-bitumen attachment correlates well with the improved bitumen recovery from poor processing ores using kerosene-coated oily bubble flotation technology.

Jan 1, 2005

This paper is for mine managers. It is about maintenance of mining equipment. This is an extremely broad subject so this paper is given with the caveat that it necessarily contains generalisations, not true in all cases, but broadly correct. The job of mine managers is to be good at making money from the excavation and preliminary treatment of mineral. To do this well, they need to understand the cost and value drivers in the business. This includes understanding the drivers associated with maintenance. Maintenance is often identified as a problem at mine sites. It is frequently listed as the cause of production shortfalls when reporting. The state of maintenance within mining as an industry is generally among the lower end of the range, when compared to manufacturing, petrochemicals, etc. Why is this? Experience and review of many audits and evaluations of maintenance has shown that some patterns are consistent with good performance and some consistent with poor performance. These often centre around the time horizon of the management team and are associated with knowing the sensitivity of the business to certain maintenance drivers and the mechanisms of maintenance and their results. To summarise, some common misunderstandings can be listed as statements that are obvious and extrapolations from those, which are not necessarily correct. For example: High availability of equipment is necessary for production. Incorrect extrapolation:focus on availability will produce high production. Design is often the greatest factor in determining the reliability of a mining machine. Incorrect extrapolation: the newest and biggest machines generally have the lowest cost operations. Operation has an enormous impact on machine productivity and reliability. Incorrect extrapolation: the fastest operators are generally the best from a productive point of view. Some maintenance improves the performance and reliability of machines. Incorrect extrapolation: more maintenance will give you more reliability. Some maintenance depends on disassembly and reassembly of components. Incorrect extrapolation: assembly is basically the reverse process of disassembly. Maintenance improvement in the mining industry in the last 15 years has focused largely on planning and systems improvement. Incorrect extrapolation: most of the problems in maintenance can be traced to a lack of planning. Actions based on flawed extrapolations will steer a business suboptimally. It is therefore important that the mine manager understands these issues so that the improvement effort can be directed to the greatest benefit.

Jan 1, 2006