Search Documents

US 4,190,436 - In the cyanide leaching of gold ore in tailing or ore dump piles, or gold ore in vats or on pads, the ore is agitated and oxygenated by introducing timed bursts of air, along with cyanide in a cyclic or regulated manner. The leach liquor is drained from the material by providing a continuous flow of air. Fines are homogenously mixed, thereby reducing channelling In the ore bed. Yield is improved and cyanide consumption lessened. R M. Hughes Feb. 26, 1980. 7 pp. (75-105). Filed. 12-20-77 (862,335).

Jan 1, 1982

By Lee Hillard Meltzer, Ralph E. Davis

INTRODUCTION During the past few years emphasis has been placed upon methods of estimating the future expectancy of gas production from natural gas fields. Before technical methods were applied, the production expectancy over future years was based upon the knowledge of gas well behavior, learned through long experience and embedded in the "know-how" of men long in the gas producing business. It is doubtful that a technical study of future expectancy of a gas field or a group of fields was ever prepared for the preliminary planning of a natural gas pipe line system built prior to about five years ago. The decline in well production capacity was naturally recognized by all familiar with the business since its earliest beginnings more than 75 years ago. In 1953, the Bureau of Mines published Monograph Number 7, "Back-Pressure Data on Natural Gas Wells and Their Application to Production Practices," which gave to the industry the first technical analysis of the decline in production of individual gas wells. This method affords a means of estimating the future production in relation to decline in reservoir pressure. The demand for technical determination of expectancy of future gas productivity from fields or a group of fields led technical men to the application of the knowledge of well behavior to the problems. The decline in a well's ability to produce as pressures declined could be estimated by the use of the curve known as the "back-pressure potential curve" as developed by the Bureau of Mines. A field containing few, or even numerous, wells could be analyzed on the basis of the sum of potentials of all wells. In most studies of this nature, the problem is to estimate the rate of production that can be expected, not only from present wells but also, from wells that will in the future have to be drilled into the reservoir being studied. The "back-pressure potential" method requires that the following data be known or estimated: (1) Proved gas reserves. (2) Current shut-in pressures and rate at which shut-in pressures change with production. (3) Back pressure potential data on wells in the source of supply. (4) Ultimate number of wells which will supply gas, and their potential. (5) Limitations on productivity such as line pressures against which the wells will produce, friction drop in the producing string, and so forth. It is evident that the resulting estimate of gas available in each year for a future of say, 20 years, contains many uncertainties. While the method may have considerable merit for a field that is fully developed, it cannot be completely dependable in fields that are only partially developed. In such cases, some of the data upon which it is based can only be estimated or assumed. In the study of this problem during the past few years, a method has been developed which we believe has great merit, especially when applied to fields subject to substantial future drilling, and when applied to the study of fields which, on the average, appear to have characteristics similar, in general, to the average of the fields used in the development of the "yardstick" outlined herein. From an analysis of the production history of 49 reservoirs which are depleted, or nearly depleted, a curve has been constructed which shows the average performance of the reservoirs during the declining stages of production. When properly applied, this "average performance curve" can be used to determine the stage of depletion at which a reservoir or group of reservoirs will no longer be able to yield a given percentage of the original reserves. "AVAILABILITY" AND "AVAILABILITY STUDIES" The rate at which. a reservoir will yield its gas depends basically upon physical factors, such as the thickness and permeability of the sand, the effect of water drive, if any, and other conditions, and upon economic factors, such as the number of wells drilled. Within the ranges set by the physical conditions, a rate of delivery tends finally to become established. The rate (or range of rates) represents a balance between the interests of the operator, who desires the maximum return from his property and of the pipe line owner, who desires to maintain a firm supply for his market. This balance, which is influenced by the terms of the contract, determines the capacity which will be developed by the operator, and the time and rate at which the decline in production is permitted to occur. Thus the "availability" of gas

Jan 1, 1953

By Zhen Zhang, Jiang Diao, Tao Zhang, Yi Ren, Lu Jiang, Xiao-Man Yan, Bing Xie

The precipitation behavior of phosphorus enrichment phase was investigated by slag modification with Al2O3. The mineral phase of the original slag and modified slags were measured by mineral phase microscope, SEM+EDS and XRD. The mechanism of Al2O3 modification was discussed according to the thermodynamic theory analysis software (Factsage version 6.3). The results show that the high phosphorus solid solution (nˊ2CaO·SiO2-3CaO·P2O5) was generated by the continuous reaction of nC2S-C3P (nˊ＜n) solid solution and Al2O3 under 1350℃. The amount of initially precipitated solid solution (nC2S-C3P) was reduced and even disappeared with the increasing of Al2O3. If the addition of Al2O3 is enough in the slag, the high phosphorus solid solution (nˊC2S-C3P) that generated by the above mentioned reaction will continue to react with Al2O3 to produce Ca2Al2SiO7 and even C3P, which was demonstrated that the addition of Al2O3 has a positive influence on the precipitation of phosphorus enrichment phase.

Jan 1, 2015

By Louis V. Bender, R. E. H. Pomeroy, David H. Browne

E. P. Mathewson, Anaconda, Mont.—After hearing about the success of D. H. Browne with his furnaces, we in Anaconda decided we might venture into the field of pulverized coal for reverberatory smelting. We sent a delegation of investigators to see Mr. Browne and his work, and they returned, filled with enthusiasm, and said they would recommend it strongly.. We thereupon asked for an appropriation, and after some delay obtained the same and fitted up one furnace to use pulverized coal. We copied Mr. Browne's practice and his selection of machinery for drying and pulverizing coal; and we also copied the burner he used, which was a standard article on the market. We got an expert coal-dust machinery man to design our plant, and were very glad we did so as we avoided some of the unpleasantness that had been experienced at other plants through fires and minor explosions. I want to say, before describing our apparatus a little in detail, that we were quite familiar with the work of Mr. SÖrensen, the pioneer in the use of pulverized coal for copper smelting. Our attention had been called to it by Mr. Klepetko early in the game. And afterward we were familiar with the work done at Cananea by Mr. Shelby. We sent an expert to investigate the question 10 years ago. He examined the work of Mr. SÖrensen; and then went to the cement men and examined their work, and reported at great length that coal dust was the ideal fuel for them, as they took the ash from the coal and sold it as cement. He reported that coal-dust firing could not be made economical in reverberatory copper smelting, and his reasons were that a blanket of nonconducting material would cover the charge in a short time and insufficient heat would reach the charge proper, and we would have floaters over all our furnaces. The flues would be stopped by the dust that did not settle on the charge. We accepted that until our Irish friend got busy and showed us how to do it. Then we built a furnace which we thought was a slight improvement over Mr. Browne's. We put railroad tracks over our furnaces to draw the charge to the furnace. We had

Jan 1, 1915

By Yuanbo Zhang, Guanghui Li, Zhenyu Fan, Tao Jiang, Xiaohui Fan

"Iron ore sintering process is the main source of SO2 generated in the steel industry, of which the discharge amount of SO2 emission accounts for about 60% of the total. Aiming at the features of sintering flue gases and existing problems during the flue gas desulphurization, a technical route of flue gas circulation sintering (FGCS) for iron ores has been put forward. Under the simulated experimental conditions, effects of FGCS process on the main output and quality indexes and SO2 emission rule are researched using simulating flue gases. Compared the novel FGCS with conventional sintering process, SO2 in the final sintering flue gas is obviously enriched and the total exhaust gases can be reduced evidently. The decreasing of oxygen content in circulating gases has bad effect on the sintering indexes. Increasing the oxygen potential is beneficial to obtain high quality sinters. This investigation shows that the FGCS process is promising.IntroductionSteel is a kind of essential material for modern society, but steel-making process is characterized by high energy-consumption and emission as well as heavy environmental pollution. Chinese steel industry has developed rapidly in the last decade, and the environmental problem caused by ironmaking and steelmaking have also aroused the greatest concern, especially the atmospheric pollution caused by SO2, CO2, etc. Iron ore sintering process is the main source of SO2 generated in the steel industry, of which the discharge amount of SO2 emission accounts for about 60 % of the total. The development of the desulfurization process for sintering flue gases to reduce SO2 emission in sintering process is not only the requirements of sustainable development but also the most important environmental tasks for steel industry [1-5]."

Jan 1, 2011

By Gifford E. White

Explanations of the basic procedure for making earth-conductivity studies by the Eltran method have already appeared in several placeS. 1,2,3 In its essentials, this method consists of applying step functions of voltage to one pair of earth grounds and measuring the transient potential resulting at a separate pair of ground points. As previously pointed out,' the transient potential resulting from a suddenly applied steady voltage is the indicia1 transfer function of Carson1 6 which has been extensively studied in network theory. The discussion here, with one special exception, will ignore the problem of how the physical configuration of the earth affects the transient response voltage; it appears that this phase of the problem has been solved in only a few special cases having any direct bearing on the prospecting problem. Entirely distinct from the potential-theory aspect of the conductivity problem is the interesting material that can be had from studying the well-known network relations between cause and effect in linear circuits, and thus deducing criteria for the application of the several experimental methods available. To do this, only one assumption need be made about the nature of the earth. The earth is to be considered a linear conductor within the tolerance of ordinary measurements. The discussion will be restricted to collinear electrode configuration like that of Fig. I, since this is the only type of spread practical for use with driving currents that vary with time. Here one pair of grounds carries the driving current, and in line with these and external to them is a RECORDING Fair of potential probes. The problem will be to consider the relation between the different voltages appearing between the potential circuit terminals when various types of driving voltage sources are inserted in the current circuit. Suppose that the grounding points G, and G2 make good contact with the earth, and that a battery of sufficient voltage to produce one ampere of direct current is introduced into the current circuit by the closing of a switch. The potential transient response to such a voltage can be measured by taking an oscillogram at the potential Directors terminals, giving the time function that has been called A(l).4 This time function has been solved for analytically in the case of a homogeneous earth,"' and the

Jan 1, 1946

By Gifford E. White

Explanations of the basic procedure for making earth-conductivity studies by the Eltran method have already appeared in several placeS. 1,2,3 In its essentials, this method consists of applying step functions of voltage to one pair of earth grounds and measuring the transient potential resulting at a separate pair of ground points. As previously pointed out,' the transient potential resulting from a suddenly applied steady voltage is the indicia1 transfer function of Carson1 6 which has been extensively studied in network theory. The discussion here, with one special exception, will ignore the problem of how the physical configuration of the earth affects the transient response voltage; it appears that this phase of the problem has been solved in only a few special cases having any direct bearing on the prospecting problem. Entirely distinct from the potential-theory aspect of the conductivity problem is the interesting material that can be had from studying the well-known network relations between cause and effect in linear circuits, and thus deducing criteria for the application of the several experimental methods available. To do this, only one assumption need be made about the nature of the earth. The earth is to be considered a linear conductor within the tolerance of ordinary measurements. The discussion will be restricted to collinear electrode configuration like that of Fig. I, since this is the only type of spread practical for use with driving currents that vary with time. Here one pair of grounds carries the driving current, and in line with these and external to them is a RECORDING Fair of potential probes. The problem will be to consider the relation between the different voltages appearing between the potential circuit terminals when various types of driving voltage sources are inserted in the current circuit. Suppose that the grounding points G, and G2 make good contact with the earth, and that a battery of sufficient voltage to produce one ampere of direct current is introduced into the current circuit by the closing of a switch. The potential transient response to such a voltage can be measured by taking an oscillogram at the potential Directors terminals, giving the time function that has been called A(l).4 This time function has been solved for analytically in the case of a homogeneous earth,"' and the

Jan 1, 1946

By Timo Niitti, Antti Rinne, Janne Turunen, Klaus Schommarz, Sami Grönstrand

This paper captures the essential steps employed in developing Outotec?s new FloatForceTM mechanism. The development of a flotation mechanism essentially revolves around the efficient transfer of installed power, or capital cost, to optimum flotation performance. Optimum flotation performance will be achieved if a balance between metallurgical results, operating and capital costs is maintained. The development of the FloatForceTM mechanism was done by careful evaluation of each of these three areas. This paper focuses on how experience, CFD and laboratory equipment, pilot and plant tests are used to test and evaluate a new flotation mechanism. Validated variables include mixing profile, power draw and local air hold-up. Metallurgical and mechanical design considerations are not covered in this paper. Besides using the FloatForceTM mechanism in new flotation equipment, the FloatForceTM mechanism can be used in existing flotation cell installations, thus enabling improvements in the mixing profiles, solids suspension and metallurgical performance of operating flotation circuits. Results of several tests carried out in existing plant operations are presented.

Jan 1, 2007

By Frederick W. Breaks, Andrew G. Tindle, Julie B. Selway

"Abstract - Rare-element pegmatites may host several economic commodities, such as tantalum (Taoxide minerals), tin (cassiterite), lithium (ceramic-grade spodumene and petalite), and cesium (pollucite). Key geological features that are common to pegmatites in the Superior province of Ontario and Manitoba, Canada, and in other large tantalum deposits worldwide, can be used in exploration.An exploration project for rare-element pegmatites should begin with an examination of a regional geology map. Rare-element pegmatites occur along large regional-scale faults in greenschist and amphibolite facies metamorphic terranes. They are typically hosted by mafic metavolcanic or metasedimentary rocks, and are located near peraluminous granite plutons (A/CNK > 1.0). Once a peraluminous granite pluton has been identified, then the next step is to determine if the pluton is barren or fertile. Fertile granites have elevated rare element contents, Mg/Li ratio < 10, and Nb/Ta ratio < 8. They commonly contain blocky K-feldspar and green muscovite. Key fractionation indicators can be plotted on a map of the fertile granite pluton to determine the fractionation direction: presence of tourmaline, beryl, and ferrocolumbite; Mn content in garnet; Rb content in bulk K-feldspar; and Mg/Li and Nb/Ta ratios in bulk granite samples. Pegmatite dikes with the most economic potential for Li-Cs-Ta deposits occur the greatest distance (up to 10 km) from the parent granite.Metasomatized host rocks are an indication of a nearby rare-element pegmatite. Metasomatic aureoles can be identified by their geochemistry: elevated Li, Rb, Cs, B, and F contents; and by their mineralogy: presence of tourmaline, (Rb, Cs)-enriched biotite, holmquistite, muscovite, and rarely garnet.Once a pegmatite dike has been located, the next step is to assess its potential to contain Ta mineralization. Pegmatites with the highest degree of fractionation (and thus the most economic potential for Li-Cs-Ta) contain blocky K-feldspar with >3,000 ppm Rb, K/Rb < 30, and >100 ppm Cs; and coarsegrained green muscovite with >2,000 ppm Li, >10,000 ppm Rb, >500 ppm Cs, and >65 ppm Ta. Pegmatites with Ta mineralization usually contain Li-rich minerals (e.g., spodumene, petalite, lepidolite, elbaite, amblygonite, and lithiophilite) and may contain Cs-rich minerals (e.g., pollucite, Cs-rich beryl). The ore minerals of Ta are commonly manganotantalite, manganocolumbite, wodginite, and microlite; Ta-rich cassiterite is also commonly present. Tantalum mineralization tends to occur in albitic aplite, mica-rich (lepidolite, cleavelandite ± lepidolite), and spodumene/petalite pegmatite zones."

Jan 1, 2005

By G. T. Lineberry, L. Adler

Due to safety-imposed constraints on clearances for mobile bulk handling equipment, it is necessary to optimally select a unit based on speed and size. The unit cannot be both large and fast. Since output is proportional to both size (or capacity) and speed, the combination must be carefully examined to maximize output. A simple graphical procedure and a calculus-based solution are presented to accomplish this. While the procedure applies to all mobile bulk handlers, as an example of the solution technique, attention is focused on shuttle cars. Background Major variables To fully define a bulk handling problem, the conditions, equipment, and activities must be characterized. The conditions and activities, when lumped together, are termed "encumbered space," since they "act to impede motion, as with a burden" (Lineberry, 1979). The insertion of mobile bulk handling equipment into what is already a difficult set of conditions and activities compounds the state of encumbrance, as limited space is competed for by many normal and life support systems. Long (1972) recognized the effects of design criteria, including road width, on haulage vehicle speed and, therefore, on production. Velocity -clearance curves Velocity-clearance curves are either available or can be constructed in the field. A preliminary set of curves for average conditions and activities is shown in Fig. 1, where clearances are only for the side of the vehicle (Lineberry and Adler, 1984). These curves set the safe speed limits for a vehicle operating at given clearances, under given conditions and activities. When feasible, velocity-clearance curves should be constructed through field measurement and observation. Curve construction should also consider haulway roughness, distances, and operator skill, as well as loading and dumping characteristics. It should be noted that haulage capacity determination is a total systems problem, not one just dependent on velocity and clearances. Production requirements and company capabilities also influence capacity determination.

Jan 10, 1985

By Ozdemir. O.

Magnesium additions to aluminum enhance strength and hardness, lowering density, and improving corrosion resistance. However, during melting and casting processes, significant amounts of magnesium are lost due to selective oxidation. Preventing these losses would reduce the production cost and improve the quality of the final product. The effects of strontium addition on the oxidation behaviour of aluminum-0.5% and 1% magnesium alloys were investigated by monitoring sample weight gains with time with a thermogravimetric balance at 750°C. Sample cross sections have been examined using Field Emission Gun Scanning Electron Microscope.

Jan 1, 2004

By Frank Gómez, Solange Ríos, Jean Valencia

La eficiencia y evolución de las actividades de perforación y voladura son de gran relevancia en la actualidad debido al impacto que causa en los procesos posteriores dentro de las operaciones mineras. Sin embargo, esta actividad unitaria experimenta numerosos problemas operativos debido a la mala elección de la malla de perforación y del explosivo, lo cual causa sobre-excavación, mala fragmentación, dilución y pérdida de mineral, entre otros. El objetivo de este trabajo técnico es optimizar las actividades de perforación y voladura de la Unidad Minera San Rafael aplicando los modelos de rotura y predicción de cavidades.

Sep 30, 2022

THE primary interest in the subject of this chapter lies in the fact that various heats of steel made to the same chemical specification do not always-have the same properties. The properties considered here, of course, are those inherent in the ingot immediately after solidification and not qualities imparted by variations in subsequent mechanical or thermal treatment. The expression "made to the same chemical specification" is used because some of the variations in properties are due to variations in chemical analysis within the specified ranges of those elements commonly specified and determined. Other variations in properties are due to variations in those constituents of steel (elements or compounds) that are not ordinarily included among the elements specified, thus not a part of the specified "composition." The term "constitution" is used to include not only the specified composition but also the nature and distribution of every element or compound contained in the steel entering the ingot mold; also included are items such as aluminum oxides and nitrides, presence of soluble gases, and dispersion of nonmetallic particles. When it is considered that the constitution of steel is determined by the addition or absorption into the bath of all such constituents from whatever source, it follows that constitution is of necessity the final result of steelmaking practice. It is the agency through which steelmaking practice operates to control the properties of the steel. The term steelmaking practice is here used in the broad sense, meaning the control of all the materials entering the steel and of the conditions under which the process is carried out. Steelmaking practice, thus defined, establishes the chemical system within which the reactions between components must proceed in obedience to the laws of chemistry. Thus the chemical constitution of the steel is established and, through constitution, the properties of the metal are established. In the preceding chapters it has been shown how the constitu-

Jan 1, 1951

By Rusty Mchenry, Craig Dickerson, Robin L. Oldham

"It has been proven that longwall faces can be moved safely and efficiently. However, abutment pressures and poor ground control conditions can halt operations and be hazardous to coal miners. Recently at a mine in Southwestern Pennsylvania, roof material collapsed above shields that created two large voids and caused major challenges for shield recovery. A unique, engineering solution was developed that utilized a modified concrete material to fill the voids, creating stability in the affected area. The many phases of this project included the construction phase, void pumping, cutting out, and bolting of the concrete material. This project eliminated the hazards associated with bolting the recovery face and removing shields in adverse conditions, making it possible for the mine operator to safely complete the longwall move.INTRODUCTIONFrequently in the mining process, especially during the recovery phase, voids above the longwall supports have occurred. These voids are simply roof cavities caused by falling rock strata above the longwall face. Most often, this condition slows down or halts mining operations and creates hazardous work conditions for coal miners. Numerous methods of supporting void areas on longwall faces have been attempted and utilized throughout the mining industry since the advent of the longwall mining system. These methods have utilized many different materials and processes and have included the installation of steel or wooden beams, crib blocks, and various types of roof bolts. However, these methods can be dangerous due to exposure of personnel to the mine voids, falling roof material, and the necessity to handle large amounts of heavy support materials.This paper describes a unique case study in Southwestern Pennsylvania where longwall recovery methods, through two void fills, were successfully completed, eliminating exposure of coal miners to the rock voids above. At the start of this endeavor, normal recovery operations were halted, and hazardous conditions became a concern when the voids were encountered. However, in the interest of safety, the decision was made to try a unique method to completely fill the void from the bottom of the coal seam to the top of the void with a cementitious material and then mine through it. This is in contrast to traditional methods where beams and support materials are used to stabilize the area above and in front of the mine shields, which can expose miners to the void above."

Jan 1, 2015

By A. Wahab Khair

"This paper deals with the description of the capabilities of a unique rotary coal cutting simulator which has been designed and fabricated at West Virginia University. It operates under the simulated mining conditions with in-situ stresses (horizontal and vertical stresses) being applied to a coal block of 18 in. x 15 in . x 6 in located in a suitably designed confining chamber. Cutting drum rotation can be varied from 1 to 40 rpm with the capability of stopping the drum after a predetermined number of rotations. Tests can be performed with four different bit angles, 15, 30, 45 and 60 degrees . A maximum of seven bits could be used in seven different orbits. Various cutting depths up to a maximum of 4 in. is possible.Monitoring devices constitute, Linear Variable Differential Transformers (LVDTs), pressure transducers, cascade Impactors, flow meters, flow controls and drum cutting speed. LVDTs are used to monitor the displacement of the coal block as well as the depth of cut. Pressure transducers are used to monitor the changes in pressure, both due to the thrust and due, to the intermittent cutting nature of the rotary cutting. Flow controls will be used to run the drum at a set rpm between 1 and 40 and to provide a different rate of advance. All the above mentioned devices can be operated and monitored by a fully automated control system. Six-stage cascade impactors are used to determine the mass distribution of dust along the rotation path of the drum. The fracture size, shape and Intensity can be studied by optical microscopy and the dust entrainment by using high speed photography.This equipment will basically be used to study the fracture mechanism in coal, associated with operating and in-situ parameters and further relate It to dust generation and entrainment In underground coal mines."

Jan 1, 1988

By B Davis, A H. Benzer, A N. Mainza, C M. Evertsson, L M. Tavares, M M. Hilden, M S. Powell, C Rule, G Asbj÷rnsson

The Mogalakwena North Concentrator of Anglo Platinum Operations was built with the capability to allow for future projected expansion. Several research groups, currently working with Anglo American on collaborative research over a range of projects, were brought in to review the existing operation, with a view to releasing some specific bottlenecks and providing specialist design input to the potential plant expansion.Based on a thorough review of the high pressure grinding rolls (HPGR) and crushing circuit, a wide range of de-bottlenecking opportunities were identified. This was followed by a series of surveys to provide performance measurements and to model the circuit in detail. From this effort a full simulation of the plant has been developed, including updated models of the HPGR, crusher, bins and screens. These models have been implemented in the researchersÆ Model Development Kit (MDK) version of JKSimMet, and in a prototype dynamic simulator based on the Matlab Simulink software.The observations, measurements and simulations have provided guidance and quantified the benefits of some proposed circuit modifications. Based on these findings a number of upgrades are being planned, with the aim of ensuring full utilisation of the installed equipment. The circuit demonstrates a potential expansion of over 30 per cent through minor improvements, and a 70 per cent increase in capacity with the addition of some strategic equipment.The HPGR-crushing upgrade project demonstrates the potential benefits of nurturing disparate Research groups into a strong inter-disciplinary technical team capable of supporting operational needs while developing future technology.CITATION:Powell, M S, Hilden, M M, Evertsson, C M, Asbj÷rnsson, G, Benzer, A H, Mainza, A N, Tavares, L M Davis, B, Plint, N and Rule, C, 2012. Optimisation opportunities for high pressure grinding rolls circuits, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 81-94 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By Gregory M. Molinda

Extremely difficult ground conditions were encountered in the main belt entry in a room and pillar mine in West Virginia. Several generations of supplemental support, including cable bolts, cribbing, and Heintzmann jacks and beams failed to halt roof falls that threatened workers safety and the life of the mine. Polyurethane (PUR) was injected into 27 intersections in the roof and the results were monitored by borehole video camera. The mine had averaged 2-3 falls in the beltway per year and, since the roof injection, no roof falls have occurred. Pre- and post injection monitoring of test holes showed that stability can be achieved without filling all of the existing void spaces. Video logging showed that the project goal of building a beam from 2-6 ft into the roof was successful. Pre-injection monitoring of roof fractures uphole can delineate the zones to target for reinforcement, and avoid pumping PUR into large voids to little effect. Multiple-injection zones can be identified, and the entire intersection drill hole array can be optimized based on knowledge of the fractured zones. In addition, pre-monitoring can prevent excessive hydrofracturing in solid zones. Polyurethane injection is a proven method of rock stabilization in even the weakest, most broken ground. Optimization of the injection design by pre-injection video diagnostics can greatly contribute to the successful and efficient roof stabilization.

By F. Garacia, J. Cervik

Gob holes are routinely used by the mining industry to vent methane from gobs and to prevent it from entering the mine ventilation system. In some cases, flows from gob holes are measured by centering an anemometer on the end of a discharge pipe. These measurements are erroneous and tend to be high by as much as 30 pct. The Bureau of Mines deter- mined method factors (correction factors) for anemometer measurements taken in this manner. Method factors for 4-, 6-, and 8-in (10.2-, 15.2-, and 20.3-cm) ID pipe are 0.68, 0.71, and 0.78, respectively. Comparisons between horizontal and vertical flows indicated no significant change in method factors. Consequently, the method factors for horizontal pipe flows can be applied to vertical upward flows.

Jan 1, 1987

By William J. Campbell

This report describes a Bureau of Mines study undertaken to determine the applications and limitations of solution techniques as a general method of fluorescent X-ray spectrographic analysis. Systematic errors due to variations in particle size, surface preparation, and sample inhomogeneity are eliminated by the use of solutions. The range of applicability of fluorescent X-ray spectrography is increased in two ways: (1) Samples in the form of wire, filings, turnings, etc., can be analyzed as solutions, and (2) samples submitted as solutions can be analyzed as received 0 The lower limit of detectability varies from 0.14 gram per liter for sulfur, atomic number 16, to 0.0015 gram per liter for strontium, atomic number 38. Most elements have limits of detectability between 0.02 and 0.002 gram per liter.

Jan 1, 1959

By Qi Wang, Zengzhu Kang, Jianguo Liu, Guanglei Liu

"Due to the increase of automotive vehicles, available parking spaces become a new type of limited resource in central cities of China, especially in those old districts without visionary urban planning. Additional mechanical parking in underground space is an efficient solution to provide parking spaces under the situation where the urban space is constrained. Shichahai district is an old protected zone in Beijing which is close to the Forbidden City and there are many Hutong (alleyway) and Quadrangles (courtyard house). No spaces are available for car parking on the ground and all vehicles are parking in Hutong without order currently. The local government plan to do renovation work for this district and improve the residential environment. Several innovative solutions are studied including parking in deep shafts, parking under existing buildings by under-pinned method, parking under buildings by covered excavation method, parking under roads built together with utility tunnel etc. 5000 difference types underground parking spaces are planned to be constructed in the following three years. Project examples are also introduced in this paper. INTRODUCTIONCar parking resources are very limited in central cities, especially in old districts without planning for increasing automotive vehicle volume. Traffic get worse when cars park on the side of the roads or move slowly to find parking spaces. Investigation shows the normal (parking space/ automotive vehicle volume) ratio is about 1.2 in most big cities such as New York, Tokyo and Hong Kong, while this ratio is only 0.5 in Beijing. One solution is to move cars out of central cities. But there are still huge parking requirements for the citizens living in central cities. Shichahai district is an historic protected zone in Beijing which is close to the Forbidden City and there are many Hutong and Quadrangles (refer to Figure 1 for project location). No spaces are available for car parking on ground and all vehicles are parked in Hutong without order currently. The local government had a plan to do renovation work of this district and improve the residence environment. 5000 different types of underground parking spaces are planned to be constructed in the following three years. One project designed and to be constructed by Zhongyan Technology will be introduced in this paper. Other innovative solutions will be introduced briefly as well."

Jan 1, 2017