Search Documents

By Jérôme Boutin, Rémy Oddo, Sylvain Ouellette, Paul-Émile Boileau, Gilles LeBlanc, Pierre Marcotte

ackleg rock drills are widely used in the mining industry and are known to generate high levels of hand-arm vibration which contribute to the development of the hand-arm vibration syndrome for exposed miners.1-3 To reduce the vibration levels, a prototype of an antivibration handle was developed as part of a previous study.4 To provide some bench marking for this handle prototype and to follow the evolution of its performance over time, a test bench was developed to characterize the vibration emission values of jackleg drills under controlled operating conditions. As the current ISO 8662 series of standards could not apply directly to this type of tool, there was a need to design and validate a test bench to evaluate the vibration emission values of jackleg drills, while taking into account the conditions specific to the operation of this type of tool. Methods A test bench including an energy absorber, was developed for testing jackleg drills based on the ISO 8662-3 standard 5. The energy absorber was bolted to a 3300 kg concrete block to ensure tool stability. A pictorial view of the device is given in Figure 1. For validation purposes, acceleration measurements at the handle of a conventional jackleg drill were taken simultaneously along the three axes (xh, yh and zh) in an underground rock drilling operation as well as on the test bench. The handle accelerations were measured for three different jackleg angles (13º, 28º and 43º) determined with respect to the floor. Moreover, each measurement was repeated at least three times to asses the data repeatability. [ ] Results As a preliminary validation of the test bench, Figure 2 provides a comparison of the frequency weighted rms acceleration spectrum measured along the zh-axis, for both underground drilling and operation on the test bench (28º jackleg angle in both cases). It is shown that the vibration measured on the handle of a jackleg drill operating on the test bench is representative of that recorded during typical rock drilling operations, despite the fact that some harmonics of the percussion frequencies are generated with a higher amplitude on the test bench. Table 1 provides

Jan 6, 2006

By Young Hyun Paik, Hyung Sup Choi, Yeun Sik Kim

The basic studies on the surface properties and flotation characteristics of ilmenite were made by electrophoretic, adsorption, contact-angle and floatability measurements. The isoelectric point of ilmenite is found to be at pH 5.6. By combining the results of electrokinetic studies and adsorption measurements, a clearer picture of the ilmenite-solution interface was observed. These findings were correlated with the floatability of ilmenite obtained by Hallimond tube tests. The general flotation characteristics of ilmenite are compared with those obtained for magnetite and rutile. It is indicated that the above three minerals, namely, ilmenite, magnetite and rutile, have very similar surface properties and flotation characteristics. Therefore, it is difficult to make an effective separation of these minerals by flotation. However, it is found that sodium orthophosphate acts as a selective depressant for magnetite in anionic flotation. Therefore, close pH control of the pulp in the presence of the phosphate ion enhances the possibility for a successful separation of these minerals.

Jan 1, 1967

By Anderson Dana

THIS PAPER describing methods and costs of mining and preparing gravel and sand for market at the Port Jefferson plant of the Seaboard Sand and Gravel Corporation, is one of a series of articles on gravel and sand mining, prepared for and published by the U. S. Bureau of Mines, which is designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs, It is recognized that publication of total costs might in many instances cause embarrassment to individual producers, as well as to the industry as a whole. On the other hand, operating costs are essential to the technical [ ]

Jan 1, 1932

By Edward D. Thimons

The Bureau of Mines conducted a state-of-the-art study of techniques currently employed to close large openings in underground mines. A large opening was considered to be any opening over 10 feet high and having a cross section of at least 200 square feet. Five salt mines and one limestone mine were visited to observe various methods of sealing large openings. Because of the variations in conditions from mine to mine, no definite conclusions could be drawn as to which is the best method. In mines where waste material is available, stoppings built by piling waste material are efficient and economical. Where waste material is not available properly constructed brattice cloth stoppings are superior to those built from wood, concrete block, or urethane foams.

Jan 1, 1975

By D. J. Burkhardt

Newer copper SX/EW facilities often incorporate hot water heating for the cell feed electrolyte to obtain the necessary plating temperatures of 40 to 50°C. Heating is most necessary in oxide heap leaching, however it may also be required in bioleaching of secondary sulphides in colder climates or higher altitudes where most of the heat gain in the heap is lost to the environment. Given that the solution flows in the leach, organic circuit and electrolyte circuit are circular in nature, and the fact that the hot lean electrolyte is often exchanged with cooler rich electrolyte, it can be difficult to access the heating requirement for the cell feed. There are energy losses in piping, tankage, raffinate, and energy gains through the PLS and electrowinning process itself; some of these are significant and others are not. This paper discusses the overall heat balance, the relative significance of the various energy gains and losses, and describes a methodology to develop a heat balance to assist the engineer in sizing the heating equipment.

Jan 1, 2003

By K. E. Robinson

This study is the extension of an investigation of reclamation of floodplain areas in the Coeur d'Alene Mining District, Idaho, that are unuseable in their natural condition, by construction of landfills with mill tailings. The study develops a valley-wide tailings disposal plan to utilize 20 potential landfill sites on floodplain areas and presents measures for reclaiming the sites for subsequent productive use. Field and laboratory testing on a test section and two abandoned impoundments support the use of hydraulically deposited tailings for landfill construction. Hydrological testing has shown that controlled discharge from tailings impoundments results in contaminant levels in the discharge below regulated standards. Additional testing indicated that compacted soil liners and pond management provide adequate contaminant abatement where acid-generating tailings are encountered. Mechanical compaction, including surcharge loading, upgrades foundation support capacity so that construction on the surface of tailings deposits is feasible. On completion of the testing program, the test sections were abandoned and rehabilitated. Details concerning potential landfill sites have been refined. At recent production rates, the 20 sites would result in 680 acres of reclaimed land, while providing a minimum of 40 years of tailings storage capacity. A general design has been developed for the retention dikes. Aspects of embankment stability, including liquefaction are discussed, and are shown to provide an adequate factor of safety under the anticipated range of operating conditions.

Jan 1, 1983

By R. R. Sayers

TWO serious hazards from coal dust confront the bituminous-coal miner- -a physical or safety hazard and a physiological or health hazard. The first threatens the miner with loss of life from coal-dint explosions, and the second with loss of health and earning capacity from inhaling large quantities of the dust. Studies by the Bureau of Mines have shown that coal dust, except some grades of anthracite dust, is capable of initiating an explosion when no explosive gas is present and that its property of extending or propagating an explosion has been responsible for nearly all the widespread explosions that have occurred in bituminous mines in the United States in the present century. For years many mining people believed that low-volatile coal dust was not explosive but not only is it explosive but if the source of ignition is intense, it is as explosive as the dust of many high-volatile coals because the war is creating increased pressure for greater coal production and because of the trend toward greater mechanization in mines, explosion and health hazards from coal dust are likely !n increase considerably.

Jan 1, 1943

By ANTON GRAY

In considering the possibilities and costs of discovering minerals by exploration. mineral occurrences may be classified roughly according to the size of the target they offer to the various methods that have been used to search them out. This classification is advantageous because the methods of search which might be expected to give results in one case may be totally inapplicable in others. Mineral deposits for the most part have been found in groups, or districts, in which the individual deposits occur under the same general geological conditions and usually contain more or less the same metals. There are, also, what are apparently isolated de- posits, although if the truth were fully known many of these probably would not be isolated. These districts, such as the Belgian Congo copper fields, the California Mother Lode, and the Linares lead district of Spain, form the first division of my classification. The second division is formed of the individual deposits of these districts, for example, Kambove mine in the Congo, the Kennedy-Argonaut vein in California, and the Cruz vein at Linares. The third division consists of the separate ore bodies that make up the deposits

Jan 1, 1949

By P. G. Semple

"In January 1985, Equity Silver Mines Limited began operation of a cyanidation circuit to scavenge precious metals from the flotation tailings. At present, this process is treating 270,000 tonnes of tailings per month and is recovering in excess of 0.20 grams of gold per tonne. To obtain these results Equity is operating a carbon-in-leach circuit that utilizes pressure stripping, zinc precipitation acid washing and thermal reactivation. A cyanide destruction circuit is also required to minimize the deleterious effects on reclaim water in the flotation stage. This paper describes the existing scavenger plant, and details the start-up problems encountered and the modifications made to correct these problems.INTRODUCTIONEquity Silver Mines Limited , a 68% owned subsidiary of Placer Development Limited , is located 38 km southeast of Houston in north central British Columbia. The geographic location of Equity Silver Mines is shown in figure #1. In September 1980, production first began with the ore being supplied from the Southern Tail open pit. In March 1984, the Southern Tail deposit had reached its economic pit depth, and since then ore has been supplied by the Main Zone pit the gold mineralization in the Main Zone is less refractory than the Southern Tail and cyanidation of the flotation tailing appeared to be a viable alternative.An extensive test program was undertaken and the results confirmed that considerable gold and silver values were amenable to cyanide leaching. A feasibility study showed that these values could be economically recovered and the detailed engineering work began."

Jan 1, 1987

By S. M. Spottiswoode

Much as one hopes to predict whether damaging seismicity might occur somewhere in the next shift, this is not possible at present. Recently, an analysis of seismicity at two mines has shown that a small increase in seismicity occasionally occurs before both large and small events. This analysis is extended here to five mines, with the same results. Earthquake seismologists forecast hazard in terms of the average incidence of earthquakes over the last 50 years, adjusted on an hourly basis according to the possibility of aftershocks of events that have happened. The rate of seismicity in any area remains approximately constant when expressed as seismicity per area mined, or better still, per unit of elastic strain energy released. It is suggested that seismic hazard in mines be estimated using historical seismicity and forward modelling, adjusted according to the possibility of aftershocks. In summary, medium-term forecasting of seismicity is viable; short-term prediction of large events is not.

Jan 1, 2010

By Ana Pereira, Naomi Norris, Donald Bruggers

The city of Christchurch, New Zealand is predominantly founded on alluvial sediments consisting of interbedded layers of loose to medium dense sand, soft to stiff silt and clay mixtures, and pockets of organics. These soil deposits have high liquefaction potential. Following the 2010/2011 Canterbury Earthquake Sequence several ground improvement trials were undertaken within Christchurch to understand the effectiveness of different types of ground improvement in these silty sand geological conditions. This paper presents a discussion of a stone column ground improvement trial undertaken at a Christchurch site with high fines content soils. Stone columns were installed using two types of installation methods and a range of Area Replacement Ratios (ARR) to assess the effectiveness of these ground improvement methods in high fines content soils as well as the influence on the type of installation method. Pre- and post-column installation CPTs, seismic Dilatometer Tests (sDMTs), cross-hole shear wave velocity tests, and plate load tests have been undertaken to assess the effectiveness of the ground improvement. Results of the testing are presented in this paper. INTRODUCTION This paper presents the results of a stone column ground improvement trial undertaken in Christchurch, New Zealand (Fig.1). In 2010 and 2011, four large earthquakes (greater than magnitude 5.9) and thousands of smaller aftershocks occurred in the greater Christchurch region. These events are referred to as the Canterbury Earthquake Sequence (CES). Liquefaction occurred across large portions of the city during the stronger earthquakes, particularly the February 2011 event. Following the CES a large amount of data was collected across the city including the location and volume of sand boils, and the location and magnitude of ground cracks. Additionally, data from thousands of ground investigations have been uploaded into a public database. As a result, there is clear evidence that silt and silty sands liquefy in addition clean sands. The CES and resulting liquefaction motivated a series of studies and trials from different organisations aiming to better understand the available technologies for liquefaction mitigation. The subject of this paper is a ground improvement trial undertaken by a local contractor specialising in deep foundations and ground improvement. They were interested in understanding the effectiveness of stone column ground improvement in high fines content (silty) soils using two different installation techniques, vibratory and non-vibratory. Different arrays and Area Replacement Ratios (ARRs) were used for each of the two methods of columns installation.

Jan 1, 2019

By H. D. B. Wilson

THIS PAPER has resulted from a preliminary draft of a background paper prepared anonymously for the Science Council's Special Study of the Solid-Earth Sciences in Canada. The draft was circulated to eighty-four Canadian geologists; forty-eight of these responded with criticisms of the draft. All critical re-marks were considered carefully and most have been incorporated in the final paper in an attempt to balance the author's bias, although this bias undoubtedly still appears. Indications of support for a particular statement or section were also helpful, because many of these contradicted criticisms and enabled the author to judge the consensus. Thus, all criticism could not be incorporated because the referees did not agree. It is interesting that some remarks were con-sidered overstatements by some and too bland by others. The most perplexing critical comment was one which suggested a new author was needed, and went on to name the existing author as the most likely candidate.

Jan 1, 1970

By Zay Jeffries

AMONG the various metals with low specific gravity, two, aluminum and magnesium, are used in the nearly pure state or as bases for light-weight alloys. Although the production of magnesium is only about one-twenty-fifth that of aluminum, a higher percentage of its output is used in the transportation industry than that of any other metal. The per-centage varies from year to year but, on the average, more than three-fourths of the magnesium production has been used for this purpose. In the United States, about 40 per cent of the aluminum production is used for transportation purposes. It seems obvious that equipment demanding repeated movement with need for rapid acceleration and deceleration should be as light in weight as the economics of engineering materials will permit. There are, however, differences of opinion with reference to both the economics and the engineering aspects of this subject. Tables 1 to 7 inclusive relate to the principal light-metal materials currently used in the transportation industry. These, with the accom-panying titles and footnotes, are in the main self-explanatory. Although the variations in mechanical properties can be easily seen from the tables, it should be kept in mind that the values given are for ordinary tempera-tures and that the changes in properties with temperature are not the same for the different alloys. Also, the corrosion properties cannot be deduced accurately either from the compositions or from the physical properties. Again, certain of these alloys are used because they possess desirable combinations of properties not listed in tine tables, including heat conductivity, coefficient of expansion, machinability, ease of casting or working, light reflectivity, anodic coating characteristics, etc. These, together with variations in prices, must be given careful analysis to effec-tively utilize the light alloys. Some of the alloys listed in the tables are new and some are old, but all are standard. Even the older alloys are available in new shapes and larger sizes than heretofore, and all are used in the transportation industry in structures of new design. Certain of the applications of specific alloys will be touched upon in the following brief history of the use of the light metals in transportation.

Jan 1, 1936

By N. Rocco, G. Johnson

Implementation of post-closure draindown estimates for tailings facilities are important predictive tools for reclamation planning and often influence jurisdictional bonding. Simplified estimates of draindown have been proposed in the past but these methods are not able to capture many of the site-specific nuances as well as operational and material parameters that influence robust draindown estimates. This paper discusses an iterative approach that relies on unsaturated flow models to predict draindown rates and associated pond inventory water balances that track inputs into underdrain pond systems, solution storage volumes, implementation of active evaporation, and necessary recirculation of solution back to the tailings facilities. Specific design criteria such as climate, facility geometry, material properties, and initial conditions, as well as active closure operational considerations that can influence draindown estimate will be discussed. Concepts presented will be valuable for operators, designers, and regulators to guide closure planning and predictive analytical analyses that support draindown estimates.

Mar 2, 2022

Site specific geotechnical data, deposit characteristics and method of mining are key factors when assessing an appropriate slope design philosophy. Mining geotechnics should be viewed as an iterative design process linked closely with mine planning, development and operational safety constraints. This case study presents geotechnical investigations for slope design at Macraes Flat Gold Mine using kinematic, probabilistic and economic analyses tempered with knowledge of site specific conditions. The recommended designs not only reduce early waste stripping tonnages but also provide data to optimise final walls.

Jan 1, 1992

By Luiz Bruno de Oliveira Araujo, Luciano Morais Teixeira, Luiz Gustavo Pedrosa de Melo, Altair Lúcio de Souza

The off-line simulation of the metallurgical process in an industrial line brings several benefits such as: evaluation of the influence of the main parameters that affect the results of the process, comparison between different set ups, greater assertiveness in operational adjustments, process optimization and reduction tests for development of new products. With this objective, a software for offline simulation of the hot strip mill process of Gerdau Ouro Branco was developed based on the logic of calculations implemented in the online model. The software results in important process variables such as mill pass scale, load, torque, and power at each pass, temperature and the hot mean flow stress of the simulated material. During rolling mill process the strip presents different temperatures and time between passes for different points along the length, which directly influences the hot strength of the product and consequently in the calculated variables, thus the calculations executed by the software were divided to three points of the strip, head, body and tail bringing the individual results to each of these positions.

Oct 1, 2019

By Theodore H. Budd, Douglas J. Heinz

This report concerns the successful construction of Contract No. 287 of the Northeast Side Relief Sewer System for the Metropolitan Sewerage District of the County of Milwaukee. The contract involved the construction of approximately 3316 meters (10,880 feet) of tunnel concrete lined to 1.83 meters (72 inch) internal diameter; 30.48 meters (100 feet) of 1.83 meters (72 inch) reinforced concrete pipe jacked-in-place; a river crossing of approximately 107 meters (350 feet); 197 meters (647 feet) of 1.83 meters (72 inch) reinforced concrete pipe in open-cut; several diversion and flow monitoring structures; and miscellaneous manholes and appurtenances. The contract proposal, which was extremely prescriptive, did allow alternative methods of primary support consisting of precast reinforced concrete segments, steel liner plates, steel ribs with wood lagging, and combinations thereof in designated areas. The specifications required the contractor to designate which support scheme it intended to use. The specifications also required compressed air as a means of ground water control for approximately 2316 meters (7600 feet) of tunnel. The alternative selected in the bid proposal was the support method consisting of steel ribs and wood lagging for 2263 meters (7425 feet) of tunnel and steel liner plates for the remaining section. Shaft supports, by specification, were designed to be steel liner plate with steel ribs varying in size from 4.27 meters to 6.10 meters (14 foot O.D. to 20 foot O.D. ).

Jan 1, 1983

By Milne J. Schmid

A program has been conducted to determine the feasibility of providing a borehole liner for Kelly Bar drilled boreholes in Southern Florida. The concept was to drill the borehole with the Kelly Bar and with it still in the borehole insert a tube which would remain in the unstable ground after withdrawl of the bar. The tube then will provide an unobstructed borehole for the charging of explosives upon completion of the drilling the shot pattern.

Jan 1, 1977

By E. G. Joe

"This paper summarizes the main conclusions derived from twenty-two technical presentations made at the 1973 meeting of the Canadian Mineral Processors. Results of two surveys with response from over seventy mines were reported on Canadian milling practice for water re-use and on elimination of cyanide from mill effluents. Water and solution recycle in Canadian mills were detailed for copper, copper-zinc, lead-zinc-copper, nickel-copper, iron and gold mines. Cyanide elimination from mill effluents was reported under current practice and under requirements for further treatment by various other processes. Three recent process equipment entries into Canadian mills have been the on-stream particle analyzer, the new gravity concentration tables for recovery of fine tin and other heavy minerals, and solution-jet slurry equipment for reclaiming ground ore from storage. The principles of operation of this equipment were described along with the practical limitations that were found in their application to mineral processing. Capital costs and milling cost reductions were shown in some operations. Computer control of flotation mill processing was a major item on the program. Four major mining companies outlined their mill process control strategy, computer programs and on-stream analysis equipment. Some capital costs and personnel changes were presented, together with gains in concentrate grade and mill recovery. Recent development work has shown the effect of the type of grinding and of aeration on the recovery of sulphide minerals in flotation. One mining company reported a significant depressing effect on copper sulphide flotation while floating ore ground with mild-steel balls; also, pyrite appeared to be activated in the subsequent zinc flotation step. One company with extensive experience in the application of aeration to copper sulphide flotation showed significant improvement to copper recovery by pre-aeration. Both the effects of grinding and aeration were subject to the constraints of the chemical condition of the ore pulp. The metallurgy of silver recovery by combination grinding - gravity treatment and of gold recovery from a complex gold-sulphide ore were reviewed in two papers on precious metals. The latter paper further described the recovery of gold from the Cottrell collectors and the final disposal of arsenic from the dust collectors."

Jan 1, 1973

By Lewis Stansfield

A rotary displacement method was used to install permanent steel casings for bored piles through an asbestos tip. This method was chosen in preference to alternative driven systems because it was quieter and more versatile if obstructions were encountered. New equipment was designed and made specifically for the project, and stringent health and safety regulations had to be observed.

Jan 1, 2000