Search Documents

By Balesh W. Konda, Andrew B. Cecala

Face ignitions occurring during longwall mining are increasing each year and are expected to continue to increase as deeper and gassier seams are mined. Effective methane monitoring strategies are needed to supplement techniques developed either to control the ignition sources or to dilute the gas to an acceptable concentration. Present monitoring strategies do not always detect dangerous concentrations as rapidly as they should. In a number of instances, dangerous concentrations have been observed at the shearer, but are diluted to acceptable levels when measured at the tailgate monitoring location. To effectively monitor and control methane concentrations, methane liberation and emission patterns must be identified. This need has led to a joint research effort between the Canada Centre for Mineral and Energy Technology and the United States Bureau of Mines. By combining the knowledge and experience of both organizations, the methane hazard facing underground longwall operations can be addressed more effectively. A comprehensive plan was developed to monitor methane levels throughout the panel and for an entire longwall mining cycle. In June-July 1986, a case study was performed at the Cape Breton Development Corporation's Lingan colliery in Sydney, Nova Scotia. This initial study was performed on two advancing longwall panels. Methane concentrations and flow patterns from this study are described in this report. A similar study is planned on a retreating longwall panel.

Jan 1, 1987

By A Harris, L Balzan

Accurate measurements of the moisture content of iron ore have increasing importance in modern mining operations. Knowledge of the moisture content allows process control actions to be carried out to ensure that the moisture is within prescribed limits, whether this is ensuring sufficient moisture to be above the dust extinction limit or that the moisture level is below the transportable moisture limit for sea shipments. Additionally, controlling moisture within desired limits can allow for greater throughput of iron ore by limiting the amount of water transported. There are a range of options available for operators wishing to obtain moisture data, though there are few demonstrated and proven devices that are able to provide real-time analysis of the full bed-depth of material. Scantech’s through-belt moisture systems are able to accurately analyse the full bed-depth of conveyed iron ore in real time using its unique microwave transmission technology, providing valuable data for operators. Recent advances in these systems have overcome errors associated with the highly attenuating nature of iron ore, particularly for large conveyor belts and deep ore. Furthermore, analysis of different ore mineralogy and its effect on the accuracy of moisture analysis has been examined and quantified. This paper discusses some of these recent results, demonstrating achievable accuracies in spite of changing ore mineralogy. Scope for future work is also briefly discussed, concluding the paper.CITATION:Balzan, L and Harris, A, 2015. Real-time through-belt moisture analysis for iron ore, in Proceedings Iron Ore 2015, pp 539–542 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By F. V. Lenel

Resistance sintering under pressure is a method of hot pressing in which a powder compact is subjected to pressure and simultaneously heated by passing a low voltage high amperage current through it. Equipment for this process is described. Its basic characteristics such as resistance requirements for powders and compacts, temperature distribution in compacts, and gas reactions during resistance sintering are discussed. Examples of the sintering process in compacts made of a single metal or an alloy powder and in compacts made of mixtures of powders are presented. Potential commercial applications of the process are evaluated. THE usual sequence of operations in commercial powder metallurgy is to compact metal powders in a die at room temperature and sinter the compact subsequently without applying pressure while the compact is in the sintering furnaces. In hot pressing, on the other hand, the compacting and the sintering are combined. The loose powder, or in many cases a cold formed compact, is inserted into the die which is held at the hot pressing temperature, the compact is left in the die until it attains its temperature, and then pressure is applied and maintained for a given length of time. The die may be heated by surrounding it with a suitable furnace, by high frequency induction heating, or by passing current through the die. In hot pressing, compacts of high density and good mechanical properties can be produced in a relatively short time. One of the principal difficulties in hot pressing is the lack of suitable die materials which will have adequate strength at the hot pressing temperature. This difficulty can be overcome at least partially by heating only the material to be hot pressed without heating the die directly. This can be done by passing a low voltage high amperage current through the material and simultaneously subjecting it to pressure. Either loose powders or compacts can be hot pressed by this method in which the desired temperature is produced by the power dissipated in the metal powder. This method of hot pressing has been termed "electrical resistance sintering under pressure." The most significant differences between this operation and conventional hot pressing are: 1—The sintering times are very short, usually a fraction of a second and at most a few seconds. 2—The powder and die are initially cold. 3—Heat is generated within the powder itself and not conducted in from the die. 4— The pressure used is high. 5—Cooling following sintering is rapid, amounting to a quench. Resistance sintering of metal powders under pressure has been suggested repeatedly. In 1933, G. F. Taylor' proposed an apparatus which consisted of an insulating tube made of glass, or a ceramic filled with the powder to be pressed, and plungers above and below the powder. The powder was to be heated by passing an electric current through it and pressure was then applied. The apparatus was intended principally for hot pressing cemented carbides. Although the principle of resistance sintering under pressure is clearly shown in this patent, few details are given. A sintering period of a second or a fraction of a second, which is terminated by the operation of an inertia switch, is mentioned but no values for current density are mentioned. Low pressures, such as atmospheric pressure or a somewhat higher pressure exerted through a lever, are suggested. W. D. Jones' discussed electrical resistance sintering under pressure and proposed using resistance welding apparatus for this purpose. In a patent issued in 1944, G. D. Cremera described a method of electrical resistance sintering under pressure using resistance welding apparatus which was to be applied mostly to nonferrous metals such as copper, brass, bronze, and aluminum. Current densities of 400,000 amp per sq in., sintering times of 1 and 2 cycles of 60 cycle current, and pressures of 5 to 10 tsi are proposed. Cremer suggested using an

Jan 1, 1956

By Robert Mehl

THE Widmanstätten figures found in the steels have been long recog-nized and in some aspects carefully studied,1 especially as they occur in cast hypoeutectoid alloys. Aside.from the practical importance of the structures obtained in the steels by various heat treatments, a study of the characteristics of these figures is interesting because of the rich opportunity the system affords, to, obtain new data on the mechanism of segregation from solid solutions. This opportunity is twofold: first, by changing composition within the austenite range the proeutectoid precipitate may be changed from that of ferrite to that of cementite, thus offering the same opportunity for changing the type of precipitate while maintaining the same basic lattice as that afforded by the Cu-Zn alloys;2 and second, the eutectoid inversion leads upon drastic quenching to the formation of martensite, a Widman-stätten figure of unique interest from ;the crystallographic viewpoint, particularly in comparison with those formed on-slow cooling.3 We have, therefore, two types of structure to study: that formed on slow cooling of hypoeutectoid and hypereutectoid alloys, and that formed on quenching hypoeutectoid, eutectoid, and hypereutectoid alloys. For each of these types of structure we require the crystallographic plane in the mother austenite along which the precipitate forms (we shall see that the precipitates in these alloys are invariably platelike in form), and also the orientation of the precipitate upon this plane. Some of these

Jan 1, 1933

By J. L. Gent

Compressed air distribution networks are essential for powering equipment in many mines even though some mines are replacing them with electrical power for hydraulic drills. Compressed air can be costly especially if the system is poorly designed and maintained. This paper outlines a technique for proper compressed air system design that will help mine managers reduce compressed air power costs; an important topic in today's highly competitive international minerals market. Compressed air system design is complex. It requires specifying: 1) air quantity and pressure in all branches of a large network, 2) proper location and types of valves and fittings, 3) the network solution that determines compressor requirements, 4) optimal hose and pipe, diameters, 5) receiver and compressor accessories, and 6) required capital and operating costs.

Jan 1, 1989

By M. J. Blackburn

The ordering reaction and its effect on dislocation awangements in alloys based on Mg3Cd has been studied by transmission electron microscopy. Ordering occurs by the growth of ordered domains until they impinge, thus producing an antiphase domain boundary (APB) network. In the disordered alloy, slip is confined to the basal plane while in the ordered condition slip occurs on the basal, prism, and pyramidal planes. Superdislocations have been identuied on these planes and their origin and expected spacings are discussed and compared with the observations. The APBs between the dislocation pairs have been resolved and have proved useful in the identification of superdislocations. Observed slip structures are related to the changes in mechanical properties produced by ordering. At high temperatures magnesium and cadmium form a continuous series of disordered hexagonal solid solutions. At lower temperatures three ordering reactions occur; two based on the compositions Mg3Cd and MgCd3 are transformations to DO19-type superlattices while alloys based on the composition MgCd transform to a B19 lattice. The ordering process in alloys near the composition Mg3Cd has been studied by several workers'-4 and it has been shown to be a first-order type transformation. The variation of mechanical properties with the degree of order and temperature have been reported in some detail by Stoloff and Davies.5 It was shown that the disordered alloy was stronger and less ductile than the ordered alloy, the differences being attributed to changes in the number of active slip planes and to the presence of short-range order in the disordered alloy. In this investigation the ordering reaction has been qualitatively followed by transmission electron microscopy. The effect of this ordering transformation on the dislocation arrangements in deformed specimens has been studied in some detail. EXPERIMENTAL Alloys were melted in a stainless-steel crucible under a flux and chill cast; both melting and casting were performed in an argon atmosphere. The ingots were hot-rolled and tensile specimens cut from the resultant strips. Some large-grained specimens were grown by the strain-anneal method. Heat treatment was carried out in inert atmosphere furnaces and in oil baths at the lower temperatures. Thin foils for transmission electron microscopy were produced by electropolishing in a cooled solution (temp = -40°C) containing 50 cu cm of nitric acid and 180 cu cm of methanol at a potential of 10 v. The ordering reaction was followed by transmission electron microscopy, X-ray, and electrical resistivity measurements but this paper will be concerned chiefly with the electron-microscopy results. Much of the work described in this paper was performed on an alloy containing 26.10 at. pct Cd although two of the micrographs are taken from work on a 25.55 at. pct Cd alloy. RESULTS i) The Quenched Solid Solution. Specimens which were quenched from above the critical temperature showed diffuse superlattice reflections. sark-field analysis on these reflections failed to reveal the presence of ordered domains and thus the superlattice reflections were assumed to arise from regions of short-range order. Quenching from temperatures of 400" to 450°C results in the formation of dislocation loops and helical dislocations. Such defects have been observed and analyzed in detail in several hexagonal metals6-' and as the crystallography and interactions of such loops appear similar in this alloy they will not be reported in detail. Fig. 1 shows a high density of loops

Jan 1, 1968

By J. Kretschmann, R. Amiri

"The Sangan iron ore mines (SIOM) in Iran are located in a remote area near the Afghanistan border. The SIOM deposit contains a geological resource of 1.1 Gt (1.2 billion st) of mostly magnetite with an iron (Fe) grade ranging from 27 to 61 percent. The Iranian government plans a stepwise development of SIOM in cooperation with private companies to satisfy the growing demand of the Iranian steel industry. Sustainable development is an influential ethical concept in mining all around the world. However, a successful realization of a sustainable development plan is not possible without a foundation on the core values and regarding the specific circumstances of the individual mining country. This paper introduces SIOM and describes sustainable development activities undertaken during its development. From the early stages, these activities have been realized to secure the acceptance of the stakeholders in the region. To evaluate their effects, indicators were filtered to the ones with the highest priority for the stakeholders. Moreover, Islamic values and Iranian regulations and their influences on SIOM were analyzed.Mining industry in Iran The Islamic Republic of Iran holds 68 types of minerals, including salt, sand and gravel, gypsum, chrome, lead, zinc, copper, coal, gold, iron, etc., with 33.5 Gt (37 billion st) of proven reserves and more than 51.7 Gt (57 billion st) of potential resources. Iran is ranked among the 15 major mineral rich countries (1). In accordance with the statistics published by Statistical Center of Iran (SCI), there were 5,316 active mines and 84,922 employees in the whole country in 2012-2013 (2) and, according to the statistics published by Central Bank of Iran (CBI) in 2011, the share of this sector in the gross domestic product (GDP) of the country was 1.2 percent (3)."

Jun 1, 2016

By D. Harrington

Seldom, if ever, has any mining hazard presented itself that some method has not been devised to control it to some extent; the degree of success of such control depends largely upon the intensity of desire to prevent suffering, injury, and death. The economic saving to be realized and the more definitely this is realized by all concerned, the more quickly and effectively will the hazards be handled is an important incentive to prevention of accidents. Preventing coal-mine explosions is by no means a complex problem; all that is necessary is sensible, conscientious, sustained effort. The fact that explosions can be prevented has been well-demonstrated by the record of the post few years; the average annual death toll from explosions for the 5 years 1906-1910 was 438, and for the 20 years prior to 1929 it was 265: during the past 4 years an average of only 32 deaths per year resulted from this cause, although the annual production during that time varied but slightly from that of 1906-10. This is a truly remarkable reduction, and if other types of mine accidents had been reduced in the same ratio only about 300 would be killed annually in our mines instead of the nearly '1,300 killed in 1936 and the approximately 2,000 killed annually for many years. Although frequency of occurrence of explosions has not lessened greatly during the last decade, their severity decreased markedly, which would indicate that effective means are being taken to prevent the spread of explosions, even though ignitions and their causes are not being handled nearly as effectively as they might or should be handled. Several large coal-producing States, which in the past have experienced numerous disastrous explosions, have been free from such disasters for continuous periods as long as 8 years in the relatively recent past. The application of rock dust to underground surfaces has been an important factor in preventing widespread explosions; some of the mast dangerous mines have been rock-dusted fairly adequately, and this has been amply repaid in the reduced severity of explosions, as heretofore indicated; however, many have applied rock dust apparently without giving much consideration to the amount required to prevent

Jan 1, 1938

By A. Cullaj

Several industrial sites suffer from the contamination of soils from heavy metals, which are emitted among others by anthropogenic mining and metallurgical activities. Effective and economic physicochemical technologies for remediation of these sites remain complicated and costly. A new alternative remediation technique is the so-called phytoremediation. This is based on the ability of some plants to accumulate very high concentrations of metals from soils and thus providing the basis for a remediation of the contaminated sites. This technique as an emerging branch of natural biotechnology, has several advantages compared to the sophisticated physicochemical techniques of soil remediation. It is not only environmentally friendly but also its costs are quite low since it is solar driven. Furthermore plants can accumulate metals to such levels that the mineral recovery maybe feasible even in conventional Ni refinery or smelting operations. In this work, thc potential of many plants to accumulate nickel has been investigated in order to identify the species which offer the best phytoremedial potential for nickel contaminated soils in Albania. Field surveys have been made in five nickel-containing sites in order to identify the nickel tolerant species that have spontaneously grown in contaminated soils. Atomic Absorption Spectrometry measurements were carried out on 145 different plants collected. 16 of them were identified as having an hyper ability to accumulate nickel since they contained more than 10 000 mg Ni per kg (DW). Seven taxa are of Alyssum genus and one of Bornmuellera genus of Cruciferae. The highest accumulation of nickel was present in aerial parts of Alyssum murale var. chlorocarpum Hausskn (25 500 mglkg or 2.5%) and Alyssum markgrafli O.E. Schulz (23 700 mg/kg or 2.37%). The seeds germinated are more evidenced at A.m.var. chlorocarpum, about 63%. These plants are suggested as the most promising species to be used for phytoremediation purposes in nickel contaminated soils and phytoextraction of nickel.

Jan 1, 2003

By Reda M. Bakeer

"Measurements obtained during load testing of two steel H-piles driven at a site in Northeastern Mississippi are discussed. The general site conditions, equipment used, testing procedures and results of the pile load tests are presented. Both piles were tested in compression and one of the piles was subsequently tested in tension. The piles were instrumented with strain gauges and extensometers to measure the mobilized soil resistance and pile movement. Three different “zero strain” conditions were used to determine the mobilized soil resistance and residual loads due to driving or a load cycle. It was concluded that the effect of residual loads on driven piles could be significant. Driving residual loads influenced the magnitude and distribution of the load transfer curves more than those due to a load cycle. Results of the tension test were impacted by the residual loads from the previous compression test performed on the same pile.INTRODUCTIONSeveral factors affect the performance of a deep foundation system including the subsoil conditions, loading settings, pile type and installation method. Residual stresses develop in piles particularly due to pile driving, but they are typically not accounted for in the analysis (Fellenius 2002). Siegel and McGillivray (2009) presented an assessment of residual loads measured during load testing of instrumented auger-cast-in-place (ACIP) piles. The magnitude and distribution of residual stresses along the pile shaft and toe depend on the pile installation method, previous load cycles and time effects. Poulos (1987) reported that residual load due to driving at the pile toe is independent of pile driving equipment and may significantly affect the results of a pile load test. Hunter and Davisson (1969) reported results of pile load tests performed in compression on fully instrumented piles driven in cohesionless soils along with a discussion of the effects of residual loads. Tension loads of about 445 kN (100 kips) were measured at the pile toe after driving. Unloading residual compression load at the toe was detected as “apparent” tension since the instrumentation was zeroed prior to the test. The researchers suggested a graphical approach to obtain the “corrected” load distribution curves considering that residual load will dissipate following the tension test. Holloway et al. (1975) conducted a study on the effect of residual stresses due to pile driving and developed a computer software that accounts for residual loads. Briaud and Tucker (1984) suggested a method to account for residual loads based on the results of 33 pile load tests performed in mostly cohesionless soils."

Jan 1, 2017

By Sydney H., Ball

ONE of the important mineral discoveries of the eighteenth century was , that of the Minas Geraes, Brazil; diamond fields. The production of this and of .other diamond discoveries in neighboring states made Brazil the premier producer of diamonds, succeeding India; its 140 years of supremacy finally passed to- South Africa- 60 years ago. Three times have diamonds contributed heavily to Portugal's somewhat checkered financial history; first in the sixteenth and seventeenth- centuries when the diamond trade of India was controlled by its citizens residing in ,Goa, later in the late eighteenth and the first 75 years of the nineteenth century when the Brazilian fields were the world's source of diamonds, and now, when the Angola diamond mines are the principal source of revenue of its colony, Portuguese West Africa. Certain phases in the history of the administration of the Brazilian field are sufficiently curious to warrant description.

Jan 1, 1929

By A. Cullaj

Several industrial sites suffer from the contamination of soils from heavy metals, which are emitted among others by anthropogenic mining and metallurgical activities. Effective and economic physicochemical technologies for remediation of these sites remain complicated and costly. A new alternative remediation technique is the so-called phytoremediation. This is based on the ability of some plants to accumulate very high concentrations of metals from soils and thus providing the basis for a remediation of the contaminated sites. This technique as an emerging branch of natural biotechnology, has several advantages compared to the sophisticated physicochemical techniques of soil remediation. It is not only environmentally friendly but also its costs are quite low since it is solar driven. Furthermore plants can accumulate metals to such levels that the mineral recovery maybe feasible even in conventional Ni refinery or smelting operations. n this work, the potential of many plants to accumulate nickel has been investigated in order to identify the species which offer the best phytoremedial potential for nickel contaminated soils in Albania. Field surveys have been made in five nickel-containing sites in order to identify the nickel tolerant species that have spontaneously grown in contaminated soils. Atomic Absorption Spectrometry measurements were carried out on 145 different plants collected. 16 of them were identified as having an hyper ability to accumulate nickel since they contained more than 10 000 mg Ni per kg (OW). Seven taxa are of Alyssum genus and one of BornmueIIera genus of Cruciferae. The highest accumulation of nickel was present in aerial parts of Alyssum murale var. chlorocarpum Hausskn (25 500 mg/kg or 2.5%) and Alyssum markgrafii O.E. Schulz (23 700 mg/kg or 2.37%). The seeds germinated are more evidenced at A.m.var. chlorocarpum, about 63%. These plants are suggested as the most promising species to be used for phytoremediation purposes in nickel contaminated soils and phytoextraction of nickel.

Jan 1, 2003

By J. A. Botín

In modern mining, the core of mine planning and design is the block model, a simplified representation wherein the ore deposit is divided in a number of virtual rock cubes, each characterized by technical and economics parameters. Mining engineers use this model to design the mine and develop production schedules. Traditionally, sustainability issues are not considered in the mine design, planning and engineering processes but rather are incorporated in the later stages of the feasibility evaluation as necessary expenditures and operating costs. This paper describes the results of a research project aiming to develop a methodology to incorporate sustainability parameters directly into the block model, so that they become an integral part of the design, planning and scheduling processes. It is considered that the incorporation of sustainable parameters into the block model would yield a more responsible mine design and improve mining projects sustainability performance

Feb 27, 2013

By Kun Li, Alex Simkovich

The rate of dissolution of alumina in carbon-saturated liquid iron has been studied experimentally in a system where alumina was in the form of a cylindrical rod immersed in an iron bath contained in a graphite crucible. Data obtained consisted of the concentrations of aluminum in the melt as a function of time. In the case of static experiments, the data are shown to agree with theoretical prdictions based on the diffusion of aluminum.. The rate of dissolution was greatly increased by the rotation of the alumina rod. It is concluded that the diffusion of aluminum from the alumina/metal interface is the rate-controlling step. In the past, thermodynamic investigations of systems encountered in ferrous process metallurgy have received widespread attention. More recently, considerable work has been devoted to the study of kinetics associated with these systems in an effort to determine their rate controlling mechanisms. The alumina-iron system is of great importance in ferrous metallurgy. Yet information concerning kinetics of reaction in this system is seriously limited. The present study was made in order to establish the rate-controlling step for dissolution of solid alumina in liquid iron. LITERATURE REVIEW A number of papers concerning dissolution of solid metals in liquid metals have been reported in the literat~re. Generally, for these simple systems, dissolution is controlled by mass transfer of the dissolving species. Complex systems involving dissolution of solid metal carbides and oxides in liquid metals and slags have been studied to a much lesser extent. Skolnick5,6 reported on the reaction between liquid cobalt and poly-crystalline cylinders of tungsten carbide, in which the cylinders were dissolved while being rotated about their longitudinal axes at various speeds and temperatures. As a result of unexpected preferential grain boundary attack by the liquid cobalt, large errors in the measured dissolution rates occurred because of loss of tungsten carbide grains to the liquid cobalt. Nevertheless, it was possible to establish that the liquid Co-W carbide reaction was not controlled by mass transfer. In a similar approach, cooper7 was able to show that artificial sapphire rods, (alumina single crystals) dissolving in lime-alumina-silica slags obeyed a mechanism of mass transfer control. Here, again, the rods were rotated at various speeds and temperatures, and the process was followed as a function of these variables. Forster and Knacke8 took a practical approach to reaction between slags and refractories. By blowing argon through refractory cylinders of silica, silli-manite, or dolomite and directing the gas to rise along the slag-refractory interface, it was possible to increase the rate of mass transfer. Although the method was admittedly crude, it nevertheless permitted an evaluation of the relative stabilities of refractories with respect to slag attack. Data were interpreted on the basis of mass transfer control. EXPERIMENTAL TECHNIQUE Apparatus. An illustration of the apparatus used in this study is shown in Fig. 1. The furnace consisted of a Morganite recrystallized alumina tube wound with a molybdenum coil. A secondary molybdenum heater was mounted around the upper half of the primary coil to aid in controlling the thermal gradient within the furnace. The primary heater tube was 3 in. in ID and 30 in. long. A reducing mixture of 95 pct N and 5 pct H was maintained around the heating elements. Thermal insulation was provided by alumina powder. The chamber within the primary combustion tube contained a boron nitride block near the top to assist in controlling the thermal gradient to the furnace and also to provide a bearing surface for the rotating graphite shaft. The outside diameter of the graphite shaft was $ in. A separate threaded graphite specimen holder was screwed into the end of the shaft. The holder contained a tapered hole drilled into the end to guide the oxide specimens as they were pressed into it for mounting. Additional guidance for the rotating graphite shaft was furnished by a water-cooled bronze bushing attached to the top of the furnace. A steel clamp was fastened to the upper end of the graphite shaft and rested on a thrust bearing; the shaft and clamp were driven by a dc motor through a set of gears. Two O-rings located immediately above the bronze bushing maintained a gas-tight seal about the graphite shaft. The lower half of the alumina tube housed the crucible and charge, which were placed on a 3/4-in. diam movable alumina support tube. With this arrangement, charges could be inserted into or removed from the furnace while the hot zone was maintained at or above 1000°C. To control the temperature of the furnace, the thermocouple was mounted inside the support tube and in contact with the crucible bottom. Stray electric fields in the furnace were of sufficient intensity to cause erratic indications by the thermocouple. By enclosing the thermocouple protection tube in a molybdenum sheath and grounding this shield, the problem was eliminated. Output of the thermocouple went to an automatic continuous balance controller. Procedure. A typical run was as follows. First, electrolytic iron was premelted in graphite crucibles and cast into graphite molds with the same configura-

Jan 1, 1970

By P. R. Kalischer

IN the production of alloys by powder metallurgical processes it is often necessary or desirable to include one or more components that tend to form very stable oxides Included in this group of metals are aluminum, manganese, magnesium, silicon, and a few others In many cases it is not necessary for the sintered compact to have full density and the other physical characteristics of a cast alloy and in that event no undue precautions need be taken If, however, it s required that the sintered part be entirely homogeneous, and have maximum density and physical properties, some method must be found to reduce the surface films of oxide, which are always present on the metals, and for the metals mentioned above this is always extremely difficult, if not impossible Since the production of high-density alloys is of particular interest to powder metallurgists, some experiments were undertaken to devise methods of reducing the refractory oxides For this work, alloys of iron, nickel, and aluminum were chosen because aluminum oxide is one of the most stable oxides and because these alloys in the right compositions form excellent permanent magnets All of the pertinent properties of the magnets could be accurately and delicately measured by density measurements and magnetic tests of sufficient scope to give a complete demagnetization curve From such a curve the maximum coercive force, residual magnetism, and energy products could be obtained and compared with the same properties for a cast material Any lack of homogeneity, density, or solid diffusion would be immediately apparent as a decrease in the magnetic properties NATURE AND REMOVAL OF SURFACE BARRIERS The early work of the present investigation was based upon published processes In the published information it was claimed that by intimately mixing iron, nickel, and iron-aluminum alloy (50 per cent Fe, 50 per cent Al) powders, compressing such a mixture into the desired shape and size, and then sintering (heating to a temperature below the melting point of the component metals) in hydrogen at 1200ºC or higher, a sound, homogeneous article could be made having the desired physical size, shape, and strength, and good magnetic characteristics However, this early work showed clearly that something in the powder compress was inhibiting diffusion and the process was almost entirely unworkable In the initial phase of the investigation samples of iron powder, nickel powder, and iron-aluminum alloy powder were pressed into separate bars and sintered in hydrogen Both the iron and nickel powders sintered

Jan 1, 1941

By Robert C. Steckley

A study of joints in Marathon County, Wis., was made to determine the orientation of regional paleotectonic stresses and to develop a method of using optical diffraction analysis (ODA) in studying joint orientations and spacings. Standard geologic and petrofabric techniques employing the use of a geologic compass and a Schmidt net were used in gathering, describing, and reducing joint orientation data. Analysis of selected outcrops with ODA indicates that ODA can be applied to study both joint orientations and spacings. ODA is shown to be a rapid method that can be used to complement standard petrofabric techniques, especially in the study of joint spacings.

Jan 1, 1972

By Andrew F. McKown, Robert A. McClure

This paper will describe a trench blasting case history in close proximity to several adjacent structures, including a bridge abutment, railroad tracks, and utility pipes. Some design considerations involved in close-in blasting will be discussed, including allowable peak particle velocities and prevention of rock block movement. The importance of several trench blast round design factors is pointed out, including choice of explo sive to prevent propagation, maintaining a sufficiently high powder factor, and mucking out for maximum relief after every round. Vibration monitoring and good record keeping are shown to be important in order to evaluate blast problems and make modifications to round designs.

Jan 1, 1988

By Clinton Birch

The multiple-criteria decision analysis is a technique that helps to find an optimal solution by evaluating conflicting criteria. In this study, an approach to perform multiple-criteria decision analysis for cut-off grade optimization, which considers the diverse stakeholder groups prevalent in the mining industry, is presented. The optimization model developed in this approach links the resource block model to the financial model, enabling the process to either maximize profit, net present value, revenue to the State, or extend the mine's life. To identify the optimal cut-off grade in each case, the Excel Solver function is utilized. Although it has limitations, the Solver function can still be modified to handle models with thousands of block values for determining input variables based on the target value. Following stakeholder engagement and dialogue, a single weighted average cut-off grade can then be determined. This approach is demonstrated for nine South African Witwatersrand gold mines.

Jun 25, 2023

By D. R. Tesarik

To ensure the stability ofa tailings pond embankment, the height of the phreatic surface must be kept at or below a safe level. In this investigation, the Bureau of Mines analyzed various horizontal drain designs for tailings embankments to determine their effects on location of the phreatic surface. This report describes the investigation, and it includes 21 dimensionless graphs that can be used to estimate the drain spacing and length dimensions necessary to ensure the stability of embankments of various configurations. Analyses were based on the use of two computer codes, a three-dimensional finite-element code and a two-dimensional finite-difference code. The computer-generated results were compared with results obtained from a laboratory embankment model, other laboratory test results, and piezomet-ric data from two actual tailings embankments. Nearly the same phreatic surface locations were predicted using either of the computer codes. For one of the actual embankments studied, the predicted phreatic surface location was slightly higher than the measured location; for the other, the predicted location closely followed the actual surface trend. Phreatic surfaces of the laboratory model were slightly higher than the code-gener-ated locations, and the differences grew larger as drain length increased or drain spacing decreased.

Jan 1, 1984

By P To, A Sharp-Paul, S Jones, C Monahan

A key environmental management issue associated with mining projects is tailing disposal. In high rainfall environments this is particularly challenging and generally requires the discharge of excess water from a tailing dam to adjacent streams or coastal waters. Such discharges can potentially have adverse impacts on downstream water quality and the environmental values associated with these waters, such as providing a drinking water supply for local villagers, maintaining a fisheries resource or protecting a fish species of high conservation significance. An alternative to the construction and operation of a conventional tailing dam is Deep Sea Tailing Placement (DSTP). The key features of such a system are:Discharge of the tailing slurry at considerable depth (approximately 120 - 150 m) below the oceanÆs surface. This requires a pipeline to be laid from the process plant to a mix tank, where the tailing is mixed with seawater and entrained air released. The pipeline then continues down the ocean floor to the required discharge depth, which is below the surface mixed layer and the euphotic zone. After discharge, formation of a density current which continues to descend along the ocean floor as long as the slope is sufficiently steep. Final deposition of the tailing in an area where the slope of the ocean floor is insufficient to maintain the density current. This typically occurs at depths of more than 800 m. Water quality issues associated with DSTP include: Impacts on the oceanic water column due to the formation of subsurface plumes which break away from the descending density current. The occurrence of elevated concentrations of contaminants in the interstitial waters of the deposited tailing solids. Fluxes of contaminants from the tailing deposits into the overlying oceanic water column. This paper discusses the water quality aspects of DSTP with particular reference to a case study in Papua New Guinea. The evaluations undertaken as part of the DSTP impact assessment included consideration of both the short- and long-term chemical behaviour of contaminants and bioassays, within the appropriate water quality assessment framework.

Jan 1, 1999