Search Documents

By C. Hartford, T. Holmes

Bulk-solids handling systems are often the most over-looked component and thereby weakest links in a processing plant’s value chain. Since their performance can dictate that of the entire operation, they actually deserve special attention. When designing a liquid handling plant, density and viscosity are well known and commonly used as design parameters. Bulk solids however, differ. While the design process is similar, the relevant parameters in handling bulk solids are instead friction, cohesive strength, compressibility, and permeability. These then vary depending on the mineralogy, particle size distribution and shape, moisture content, storage time-at-rest, temperature, and consolidation pressure. With so many variables, it becomes important to characterize each individual bulk solid across the full range of representative process conditions within the handling system, plant wide – or if you are not very lucky, suffer the consequences of poor material flow. Measuring flow properties and applying them correctly in bulk solid handling system design reduces project risk, saves significant capital, and drastically increases throughput, especially when done in the early stages of a project. Keywords: Flow Properties, Bulk Solids, Process Conditions, System Design

Jan 1, 2020

By Raju S. Sagi

This paper deals primarily with the different types of drilling methods used by the Iron. Ore Company of Canada for sampling the soft and friable hematite-limonite (secondary) iron ore deposits found in the Scheferville area. The problems associated with drilling, sampling, sample handling and sample preparation. for chemical analysis of these ores are discussed. Systematic evaluation of the various drilling methods led to the selection of an integrated drilling system. This system consists of a rotary dual- tube - reverse-circulation drill, with tricone bit, polymer mud and mechanical sample splitter, The historic al development of this drilling system is described in detail, as are the equipment , sample flow and quality control checks carried out to obtain representative samples. This integrated drilling and sampling system has been used satisfactorily on a routine basis for determining the grade and tonnage of ore for the various deposits for the last five years (1972-76) in the Schefferville area.

Jan 1, 1977

By Andrea Pezza

The paper describes the recent new installation and start-up of the second RH (Recirculation Degasser) in Rio de Janeiro plant of thyssenkrupp CSA Siderúrgica do Atlântico. The new plant is installed as part of the existing RH, the twin solution increases the overall melt shop production in the area of quality plates especially for deep drawing grades. With this new equipment, CSA is able to increase degassed grades production with a state of art asset that has the ultimate technology in operation, safety and automation. The description of the main components parts and the operational concept gives an overview of the latest experience in RH plant engineering combined with best operational practice of world class steel producer.

Oct 30, 2017

By Rolando Campos

Until 1970, the Caletones Smelter of CODELCO-CHILE, División El Teniente, operated under the conventional pyrometallurgical process used by most of copper smelters. The annual copper production varied around 165.000 tons. The failure in the commissioning of the "oxygen smelting" technology in Peirce- Smith converters (1970-1972), forced further introduction of transcendental changes in the Caletones smelter operating scheme. Implemented technological innovations were based on wide studies and research works performed by División El Teniente. This paper presents a summary of technological modifications introduced, their impact on production and energetic performances, and short and medium terms improvement plans.

Jan 1, 1993

By J. Pepin

When using alternating current submerged arc welding (SAW) to produce pipes from microalloyed linepipe steels, it is critical to balance penetration depth and deposition rates, in order to minimize the number of weld passes while still maintaining good heat affected zone (HAZ) microstructures and properties. A series of bead-on-plate (BOP) submerged arc welds were performed on X70 steel, using different waveform variable settings (i.e., balance, offset and frequency). Weld bead cross-section profile deposition and penetration areas were measured, and both Vickers hardness and Charpy V-notch impact testing were performed. Both single electrode and tandem electrode welds were evaluated.

Jan 1, 2011

By Patrick J. Hannigan, Frank Rausche, Rozbeh B. Moghaddam

The Top-Loaded Bi-Directional Test (“TLBT”) is a new method to apply bi-directional loads to a deep foundation element with the loading source located above the foundation head. In the TLBT reusable load assembly, loads are applied to the foundation using the R-System which consists of two stacked steel plates located at the geotechnical resistance balance point or at the foundation base connected to the load assembly via vertical elements. The top plate or the Shaft Bearing Plate (“SBP”) will transfer loads to the foundation upper portion, and the bottom plate or the Base Bearing Plate (“BBP”) will transfer loads to the foundation lower portion as well as the foundation base. At the surface, above the foundation head, a hydraulic jack is located between a Top Load Assembly (“TLA”), and the Bottom Load Assembly (“BLA”). The TLA and BLA are connected to vertical elements which are consequently connected to the R-system. As the jack is pressurized and expanded at the surface, the R-System plates are separated, and the foundation is bidirectionally loaded. This paper presents a brief description of the conventional Bi-Directional Load Test (“BDLT”) including benefits and limitations followed by the TLBT method introduction including its benefits and advantages over other testing methods.

Sep 8, 2021

By W. Irwin

Global warming hitherto viewed as a distant threat to the environment, is now the subject of fierce goo-political debate. The debate centres around the time frame required to achieve environmental compliance, and the cost implications of meeting that objective. Since coal is the fuel of choice for power generation, the priority objective of energy producers is the pursuit of environmental protection measures that allow coal to be burned without any attendant negative impact on the environment. From an environmental point of view, public attention is today firmly focused on the impact that all industrial activity has on the environment, and coal is singled out from other fossil fuels as being the product of an inefficient smokestack industry. Despite coal's poor public image it is unrealistic to suggest as some do, that use of this fossil fuel as a primary energy source should be drastically curtailed. Coal which already generates about 35% of the world's electricity is continuing to increase its share of this rapidly expanding market, and to argue against its use is flying in the face of reality. However, changes are required in the way coal is used in some of the new clean coal technologies, since many include advanced methods of combustion. Indeed changes in the way coal is used is a vital link to the future of coal as a primary source of energy, and increased coal utilization will be directly linked to changes in its use. Discussion of various issues that affect coal utilization are the focus of this paper.

Jan 1, 1998

By C. A. Mehring

[This paper, which describes the milling practice at the San Guillermo concentrator of the Compania Industrial "M Potosi", S.A., located at Chihuahua, Chihuahua, Mexico, is one of a series of similar papers being prepared by the United States Bureau of Mines. The concentrator treats lead-zinc-silver ore at the rata of 2,300-2,400 tons of dry material daily and produces lead concentrate and zinc concentrate by selective flotation methods. The lead concentrate is smelted at the Chihuahua plant of the American Smelting & Refining Co., and the zinc concentrate is shipped to various European smelters.]

Jan 1, 1933

By M Gwynne

McArthur River Mine is located approximately 50 km south-east of the NT township of Borroloola and approximately 120 km from the Gulf of Carpentaria. The mine hosts a series of layered shallow dipping tabular orebodies, with current reserves of approximately 22 Mt, grading 13.6 per cent zinc, 6.3 per cent lead and 65 g/t silver. Owing to economic considerations, the lower most orebody (No 2 orebody) has been selected for initial mine production. Following the completion of the No 2 orebody, mining will transfer to the lower grade and metallurgically more complex No 4 orebody. The mine employs a total of 235 people throughout the underground and surface areas. The majority of the workforce work a fly-in/fly-out, seven-day- on/seven- day- off roster with 12-hour shifts. Presently, a further 18 contractors are involved in trial mining areas. An apparent dip room and pillar technique has been selected as the primary mining method. Officially opened in September 1995, the current production rate of 1.2 Mt per annum will eventually escalate to 1.5 Mt per annum. Though most production is achieved through the use of conventional loaders, trucks and jumbos, the recent development of methods utilising scrapers, hand held machines and modified jumbos has produced encouraging results in steeper dipping areas of the mine. Initial production has been hindered by several factors including extensive and largely unpredictable faulting, worse than expected ground conditions and difficulties with some mining equipment. Compounded by the relatively thin 3 m ore seam, initial mining resulted in high dilution and poor production. This paper describes the development of unique planning and production systems that were evolved in order to overcome these problems and achieve the targeted production rates and head grade.

Jan 1, 1998

By K. Luxbacher, A. Haghighat, B. Lattimer

Mine face ignition due to high levels of methane is one of the most common fire incidents in underground coal mines. In continuous miner headings, depending on the magnitude of the ignition or resulting fire, auxiliary ventilation controls may be damaged or dislodged, affecting the ventilation into the area. A computational study was conducted to investigate the effects of different levels of damage to an exhausting ventilation curtain in a continuous miner heading, and the impact on ventilation to the face. The computational fluid dynamics software Fire Dynamics Simulator (FDS) Version 6.0 was used to predict the conditions that develop due to a 200-kW fire in the face following a methane ignition with different levels of assumed ventilation curtain damage. Smoke layer depth, temperature and mass flow inby the last open crosscut were used to evaluate the impact of no damage to the curtain, partially dislodged curtain, and fully removed curtain. As more of the ventilation curtain was damaged, smoke depth and temperature outby the fire increased. With the full removal of the curtain, the smoke accumulated from the last open crosscut to the face, with the ventilation completely bypassing the continuous miner region.

Jan 1, 2016

By E. R. Cole

One objective of Bureau of Mines recycling research is to devise technology that enables recovery of metals and minerals from wastes. From October 1982 through September 1985, researchers at the Bureau and at the University of Missouri Rolla (contract H0222002) investigated the use of nonferrous flue dust with varying Zn contents (11 to 66 pct) as a source of Zn for electrogalvanizing steel wire. The waste dusts used were from a secondary Cu smelter, a brass smelter, a Pb smelter, and a water treatment plant. The dusts were leached in H2S04, and the leach solutions were treated to make electrolyte for electrogalvanizing steel wire using soluble Zn anodes. Cyclic voltammetry was used in an inno-vative method to evaluate the quality of the electrolytes used for elec-rogalvanizing. After electrogalvanizing, the wire was drawn on a labo-ratory draw bench to simulate industrial practice. Corrosion resistance was measured by a number of electrochemical techniques and by the stan-dard ASTM salt-spray tests. After successful bench-scale tests, the process was demonstrated in an industrial pilot plant. Results indicate that nonferrous flue dusts can be used as a source of Zn for electro-galvanizing if certain impurities are either partially or completely removed from the starting electrolyte.

Jan 1, 1987

By J. T. Dunham

Zirconium has possible use in industry where severe corrosion conditions are encountered because it resists attack from a variety of corrosive environments. However, very little experimental testing has been done to evaluate the corrosion behavior of zirconium when simultaneously subjected to high tensile stresses and exposed to corrosive environments. This investigation was initiated for an evaluation test, but was limited to environments consisting of ferric chloride solutions which were known to attack zirconium and were shown to promote stress-corrosion cracking in preliminary tests. Tests for cracking susceptibility were conducted by the Bureau of Mines to show the effect of stress, solution concentration, air aeration of solution, and the method of mechanical processing. Tensile stress was applied to the specimens by a constant-load method which proved more reliable than a constant-strain method.

Jan 1, 1961

By S. S. Szoke

The concrete masonry industry, represented by the National Concrete Masonry Association has significantly expanded its markets since the industry's inception. The concrete masonry industry has developed and refined concrete masonry units by producing a variety of quality products on automated machines. In the sixties, architectural concrete masonry units gained popularity. In the seventies, the concrete paver market expanded. In the eighties, segmental retaining wall units became popular. The industry continues to research and develop new products and applications for concrete masonry to satisfy the needs of designers, specifiers, installers and owners. Both existing and innovative technologies in the concrete masonry industry are discussed.

Jan 1, 1993

By Y. G. Yaroshenko, V. Y. Baldin, Y. M. Gordon

The manufacture of sulphuric acid from the off-gas of pyrometallurgical processes in the production of heavy metals is one of the common methods of effective recycling of sulfuric anhydrite. The new Impact-Inertial Devices with the rectangular contact channels (IIRCh) and the internal circulation of liquid allow the injection of an absorber into the phase's interactive cell by utilizing the gas stream energy and by this way increasing the sulphuric acid yield and reducing the power consumption. These devices have the following advantages: simplicity of design, smaller size, low capital expenses, absence of irrigating system, high operational reliability, simultaneous cleaning of solid, gaseous and liquid impurities and also cooling of gases etc. The IIRCh efficiency is almost 18 % higher and they require 1.3-2 times lower energy when compared with Venturi Absorbers. Also the elevation of spraying nozzles or injectors is 1.5 times lower in the IIRCh case.

Jan 1, 2004

By Douglas W. Fuerstenau, Pradip Pradip

The design and development of selective flotation collectors has been the key to the remarkable success of flotation in beneficiating complex, difficult-to-process ores. Sustained research efforts in the field over the past hundred years have led to delineating the scientific basis of selective mineral flotation in terms of the crystal chemistry and the surface and colloid chemistry of minerals including their solubility, and the aqueous solution chemistry of added reagents. It is now well-established that the electrical double layer theory (EDL) is the most powerful means of quantifying the relative strength of mineral-reagent interactions in the case of nonsulfide minerals. We illustrate the utility and the power of the EDL in delineating the science underlying selective mineral flotation with the help of a few examples taken from our own work, in particular on the selective flotation of rare-earth minerals (bastnaesite) from associated semisoluble minerals (barite and calcite) using alkyl hydroxamate collectors and the flotation separation of lithium-containing minerals (spodumene) from associated alumino-silicate minerals with oleate (fatty acids). Both of these mineral separation systems are of contemporary research interest and of immense value to the industry today. Recent advances in utilizing molecular modeling computations, particularly in the context of quantifying the effect of crystal chemistry and the relative distribution of adsorption sites available on mineral cleavage planes, are also reviewed.

By Raj Thamburaj

"Over the last few decades, the emphasis on affordability and reduced cost of ownership has necessitated the development of innovative processes to carry out repairs in aero engine components. Conventional weld and braze repairs have evolved into advanced, sophisticated processes using state of the art knowledge in lasers, robotics and materials technology. This paper illustrates past and present scenarios in an attempt to illustrate progress that has been made in this area. The problems encountered in the past have been detailed along with the solutions that have been developed and commercially implemented to address these issues. Apart from technical progress, this presentation also addresses the progress made in business approaches and in Certification/Regulatory issues surrounding aero engine repair. Progress in Technology Repair technologies have also been the embryo from which new and revolutionary manufacturing technologies have evolved as well. Electron Beam Free Forming and LENS are examples of how a completely new manufacturing concept can evolve what was originally only a process to join metals. The current and future potential of these spin offs is discussed providing examples of application. While several problems have been solved over time with the implementation of advanced repair technologies, the demands of the industry have created new challenges. The paper describes these issues, outlines potential solutions and discusses the future of repair technologies in terms of the far reaching influence it is sure to have in design, manufacturing, maintenance management and life extension. Progress in Business Trends.Business approaches to repair and maintenance have also gone through considerable change with the introduction of ""Power by the Hour"" and other similar arrangements between the companies responsible for engine overhaul and the end-users. Program Based Logistics (PBL) is yet another innovation to provide a win-win situation for the repair service provider and the end user. This paper traces the development of these business initiatives and highlights successful applications. Progress in Repair Certification, Regulatory Issues.Understanding of the issues surrounding certification of repairs has also evolved with time and regulatory issues have been clarified considerably. Procedures for analysis and testing are much clearer and ""Check Lists"" are being drafted for certifying repairs on various engine components. The PMA phenomenon has added yet another dimension to the issues regarding certification and these are discussed as well."

Jan 1, 2010

By A. Z. Lang, D. A. Hall

After a brief description of the causes of spontaneous heating and of general preventative methods, a detailed account is given of occurrences of spontaneous heating in the Main Seam (locally known as the 5/4 Seam) at Westoe Colliery. This seam is about 12 feet thick consisting of hands of coal and shale, but only 4 feet 6 inches is worked because of the thickness os strata in water-bearing rocks and the worked section is selected on quality considerations. An advancing longwall face in this seam (2nd South) began to heat after working for six months and ultimately had to be abandoned. By adopting retreating methods and mining narrow panels it has been possible to extract this coal at an excellent rate of productivity. The system of goaf ventilation is important, because the use of a bleed road would have given rise to dangerous conditions in a goaf which of necessity would have contained fallen coal. Preparatory seals were prepared at selected sites so that, if necessary, a panel could be sealed off quickly; these seals are completed as soon as possible (within three weeks) of finishing a panel. A gas sampling system has been instituted which includes daily sampling on the face and in the goaf, and weekly sampling at the stoppings of all completed panels. The coal has now been extracted from this seam for three years without any further difficulties from spontaneous heating.

May 23, 1905

By F. N. Smith

The carbon steel casings of Heat Recovery Steam Generators (HRSGs) in a co¬generation plant were found to have developed cracks that originated on the inside surfaces. The HRSGs receive hot exhaust gases from the primary Gas Turbines (GTs), which are fuelled with pipeline natural gas. The GTs was initially operating without any suppression of nitrogen oxides (NOx). After being in service for about two years, some of the cracks were found to have penetrated right through the 1/4 in. thick casings. The casings are fitted with insulation on the inside (hot gas side). Examination of steel samples cut from the casing walls revealed (i) fine cracks propagating through the steel from the inside surfaces, and (ii) the presence of relatively large amounts of nitrate ion on the inside surfaces. It was concluded that the nitrate ions originated from nitric acid that was condensing on the relatively cool walls of the casings behind the insulation. Nitric acid was formed in the GT exhaust gases by the combination of water vapour (formed from combustion of the hydrocarbon fuel and from moisture in the combustion air) and nitrogen oxides (formed from nitrogen and oxygen in the combustion air).

Jan 1, 2005

By G. W. Reimers

Conditions in the underground mine environment can cause self-heating of sulfide ores as a result of exothermic oxidation reactions, which may result in mine fires. This Bureau of Mines report describes thermal analyses of finely ground chalcopyrite, chalcocite, galena, pyrrhotite, marcasite, and arsenopyrite, to characterize their responses under oxidizing conditions. Thermal gravimetric analysis (TGA) and differential thermal analysis (DTA) were used, in the temperature range 1000 to 5000 C. Chalcopyrite showed an initial weight gain, due to formation of sul-fates, a weight loss, caused by ignition of iron sulfide to iron oxide, and a final weight gain, indicating the conversion of copper sulfide to sulfate. Chalcocite did not ignite in the temperature range studied but exhibited a rapid weight gain, because of the rapid conversion of copper sulfide to sulfate. Likewise, galena failed to ignite but underwent a steady weight gain when oxidized in a moist atmosphere, showing conver-sion of lead sulfide to sulfate below the ignition point. Marcasite underwent a rapid weight loss, indicating ignition, at 2000 C. Moisture in the oxidizing atmosphere lowered the ignition point of marcasite and arsenopyrite but not that of pyrrhotite. All the sulfides exhibited exothermic behavior at temperatures below the ignition point.

Jan 1, 1987

By Manfred Krutein

Ocean mining has a number of problems which are critical to its development: ? Political hurdles on national and international stages ? The worldwide economic situation, with the possibliity of a recession ? Financial difficulties in funding further work ? Technical problems for the development of ocean mining and transport subsystems ? Demands for technology transfer This paper touches the last two points and provides some thoughts for discussion and creative objectification. The many technical problems of ocean mining will be identified and some proposed solutions will be investigated relative to the state-of-the-art technology of ocean mining and nodule transport. An outlook into the future attempts identification of the steps necessary to eventually develop components for workable systems that are not only technically but also economically feasible.

Jan 1, 1978