Search Documents

By Christoph Wels, Michael Royle, Shannon Shaw

Intrinsic remediation is the effect of natural attenuation mechanisms - dilution, dispersion, sorption/precipitation and biodegradation - reducing contaminant concentrations in ground water to specified levels at predetermined compliance points in the aquifer. Current monitoring and modeling for post closure was used to assess the current and long-term potential of intrinsic remediation of contaminated seepage originating from a large reactive (sulfidic) tailings impoundment near Questa, New Mexico. It is concluded that the natural attenuation mechanisms of precipitation within the tailings (as a result of buffering) and dilution/dispersion within the aquifer are currently active and likely sufficient to reduce contaminant concentrations to below state standards in the long-term. Other natural attenuation mechanisms such as sorption and biodegradation within the receiving aquife4s) were not assessed here, but are likely further reducing contaminant concentrations. Active interception and recovery of the seepage water is being maintained until monitoring demonstrates that intrinsic remediation has successfully achieved the level of water quality control required.

Jan 1, 2000

By W. J. Jenner

"Introduction The Saskatchewan Power Corporation is a provincial crown corporation which operates under a mandate to supply all customers within Saskatchewan with electricity and natural gas. The Saskatchewan Power Corporation operates two coal mines within the province of Saskatchewan. The Souris Valley Mine is located a few miles south of the city of Estevan and produces approximately 300 000 Mg of lignite per year. The lignite is shipped about four kilometres by truck and burned at the 882 MW Boundary Dam Power Station, also owned by the Saskatchewan Power Corporation. The Poplar River Mine is located just south-west of the town of Coronach, Saskatchewan which is some 190 kilo metres west of Estevan. This mine produces approximately 1 675 000 Mg of lignite per year. The lignite is shipped seven miles by rail to the Saskatchewan Power Corporation's Poplar River Power Station. The Poplar River Mine is the sole sup plier of fuel to the Poplar River Power Station, which generates some 300 MW of electrical power. A second 300 MW unit is due to be commissioned at the Poplar River Power Station in mid-1983 and the Poplar River Mine will have doubled its capacity to approximately 3 350 000 Mg per year by that time: Souris Valley Mine Geology The Souris Valley Mine extracts lignite from the Estevan seam of the Ravenscrag Formation. This formation is of Tertiary age and was deposited during the Paleocene Epoch. The Ravenscrag Formation outcrops throughout southern Saskatachewan and all coal mined in the province occurs in this formation. Ravenscrag sediments are deltaic in origin and are composed of a series of fine sands, silts, clay and lignite deposits."

Jan 1, 1985

By Richter, E. Charikinya

"Mineral processing unit models require information on particulate properties such as particle size, solids flowrate and mineralogical composition to model their operations. Process models that describe the separation process can be classified based on the level of information required from the ore, i.e. the feed stream to the separating unit. The most comprehensive level of mineral processing models is the particle-based modelling approach. Particle based modelling describes a modelling approach where mineral composition, mineral liberation and textural information of particles making up the process streams is used in modelling. The advantage of this approach is that all model streams carry particle level information (size, liberation, shape). This information is obtained by applying automated mineralogy techniques such as Quantitative Evaluation of Minerals by Scanning Electron Microscopy (QEMSCAN) analysis which provide accurate and detailed information on process stream particle properties. Currently the use of liberation information in modelling and simulation is rare, due to the limited number of separation models that liberation data as input. The objective of this study is to develop a particle based model for a dry magnetic separator, where mineralogical information is used directly to simulate a dry magnetic separator operation. Magnetic separation tests were carried out on high, medium and low grade magnetite ores using a laboratory magnetic separator. Streams from the separator were sampled and sized for chemical and liberation analyses. A sized mass and elemental balance around the magnetic separator was carried out. The elemental assays of each stream were converted to mineral quantities and a sized mineral balance was done. QEMSCAN measured liberation data was reconciled to the mineral balance based on mineral quantities obtained from chemical assays. This was followed by the development of a particle based model that calculates the trajectory of a single particle based on its mineral composition and textural properties. The model was tested on experimental data and was able to predict the effect of variation in process feed stream mineralogical attributes (liberation, grade, particle size) on magnetic separation performance. Results of this study highlight the benefits of the particle based modelling approach. INTRODUCTION The extraction of mineral values from ore requires liberation of the value minerals from the gangue followed by their separation. Liberation is achieved by size reduction operations (Desmond, 2008; Fuerstenau and Abouzeid, 2002). Separation of gangue material from value mineral takes place in various mineral upgrading stages such as classification, magnetic separation and flotation. In these concentration stages value minerals are separated from gangue minerals based on the physical properties of the ore particles making up the feed such as size, liberation, volume of magnetic material and density. The success of separation is related to the liberation of the feed particles, the performance of the separation technology applied, as well as the inherent characteristics of the feed material (Leißner et al., 2013)."

Jan 1, 2018

By Jr. Abel

Subsidence is controlled by a complex combination of mining and geologic factors. For example, a world-wide compilation of data shows that, as the percentage of shale in the overying rock mass decreases and the amount of sandstone increases, the angle of draw (and the area affected by subsidence) decreases. Limestone in the overburden appears to cause as much as a three-fold decrease in the angle of draw compared to a like amount of sandstone. Increased amounts of sandstone were accompanied by a greater surface subsidence relative to the mining height. The total thickness of overburden did not appear to influence the subsidence magnitude above super-critical panels. The greater the thickness extracted the smaller percentage of that thickness that shows up at the surface as subsidence. The greater the percent of the seam extracted, the greater the subsidence reaching the surface. The maximum subsidence above room and pillar panels is dependent on the pillar height and minimum width as well as the other factors listed.

Jan 1, 1980

By F. S. Hoseinian, B. Rezai, E. Kowsari, M. Safari

In order to remove heavy metal ions from a large volume of wastewater with a low ion concentration, ion flotation appears to be promisingly effective. In the ion flotation process, because of the high ion removal percentage, the amount of water recovery percentage is a very important factor which determines the process efficiency. However, ion flotation suffers from relatively high collector concentration to achieve the high removal percentage to the desired limit, which subsequently increases the water recovery. In this study, functionalised graphene oxide (FGO) was synthesised, using a chemical method in the ion flotation process, applied as a collector for increasing process efficiency by reducing the collector consumption and water recovery. The high ion removal was achieved with both collectors of sodium dodecyl sulfate (SDS) and FGO, while the water recovery with a collector of SDS was 3.4% higher than that with a collector of FGO. The results indicated that the FGO could be effectively used for high ion removal and low water recovery in the ion flotation process. Keywords: Ion flotation, synthesised collector, ion removal, wastewater, water recovery

Jan 1, 2020

By D. H. Diering

Definition of mineral resources and reserves forms the basis for effective mine planning and reliable public reporting of mineral assets. Historically the mineral resource and reserves declaration process has been the domain of the geology and surveying disciplines, with the declaration of the reserves by the surveyor being based on the application of modifying factors to the declared resources available for mining. As part of an ongoing process to improve efficiency, reliability, and reproducibility of results, this approach has been revised and enhanced through the introduction of a revised process and reconciliation tools. The revised approach to reserve definition is based on the definition of scheduled resources, at an appropriate confidence estimate in the context of an approved business plan, over the anticipated life of the mineral asset being applied to define reserves. This planning and scheduling is developed, during the annual business planning process, by the mine planning department using tools such as CADSMine?. The scheduled area together with the application of revised modifying factors is tabulated in the BME (basic mine equation) and reflects the mine production plan over time. Simplification of the modifying factors to dilution and losses underpins the simple yet robust approach to improved definition of reserves in this process and in the basic resource to reserve equation (BR2RE). Dilution intrinsically affects grade but not metal content, whereas the losses reflect both the efficiency of mining and planning and are reflected in metal losses, area losses, or both. Reconciliation of the derived ?resource converted to reserve? area, (which is based on the business plan from CADSMine?), versus the ?resource available for mining?, (which is derived from Datamine?), underpins the robustness and auditability of the reserves declaration. This R&R accounting and reconciliation approach is transparent and facilitates interrogation of the logic and rationale of long-term business planning and project strategy. These numbers are processed and reported in the logic of the basic resource equation (BRE), which also addresses aspects such as white areas (future and historic), tail management, and partial extraction (non-scheduled pillars, etc.) in compliance with SAMREC definitions. Areas that do not have the necessary confidence and data support to be declared as resources find their space as pre-resource (outside the domain of public reporting), outlining existing potential for future extraction and reporting. Use of the BRE leads ultimately to a complete, refined accounting and reconciliation-oriented approach for all production entities. The revised resource and reserve process includes the discipline of mine planning as intrinsic to the definition and declaration of resources and reserves. Subsequent to the change in process, the resources and reserves have truly become the domain of the mineral resource management discipline. This paper defines the logic of the basic resource equations and outlines their application in the definition and reconciliation of mineral resources and reserves at Anglo American Platinum Limited.

Jan 1, 2012

By Ernest E. Fairbanks

[Microscopic methods have proved to be valuable assets in the study of low-grade ores. While the chemical assay u a ally discloses tine total content of valuable metals in such an ore, a thorough knowledge of the nature of the ore should form the from which to prepare an efficient means of recovery. In the treatment of low-grade ores, inefficient recovery, as indicated bay the amount of valuable mineral permitted to go to waste in the tailings, is too frequently the rule rather than the exception, As methods of recovery become more efficient, many low-grade 10 mineral A posits suddenly assume o commercial significance, In much of this material the minerals are so finely disseminated and intermixed that identification even by microscopic methods is a difficult matter. The application of microchemical qualitative analysis with the aid of new device described in this paper, will solve many of the problems of identification encountered in the study of low-grade potential ores. In these ores, especially, the limitations of ordinary microscopic methods are liable to become very great. The microchemical tests obtained by applying a standard set of reagents to a polished knoting whether or not a tarnishing action develops, have considerable value but arc far from being infallible. It is well-known that electrolytic effects are apt to affect seriously the diagnostic value of the tests, end this effect is encountered much more frequently in dealing with finely desseminated minerals. resort to microchemical qualitative analysis, therefore, becomes indispensable.]

Jan 1, 1924

By F. D. Osgood, H. M. Cooper, A. C. Fieldner

The analyses in the tables are arranged geographically with respect to county and towns, and are grouped as follows: l The proximate analysis--moisture, volatile matter, fixed car bon, and ash; 2 The ultimate analysis-carbon, hydrogen, nitrogen, oxygen, sulphur, and ash; 3 The calorific value of heat of combustion; 4 The softening temperature of ash, when such determinations were made. Ultimate analyses are given in three conditions-namely, (1) as received, (2) moisture free, and (3) moisture and ash free Proximate analyses and heating values are given generally in one condition -namely, as received, some are in two conditions, as received and moisture free.

Jan 1, 1928

By W. H. Holman, J. B. Wagstaff

IN spite of considerable interest among blast furnace operators on the question of the penetration of air into the furnace, there is still uncertainty as to how far the blast does, in fact, penetrate. Moreover, it is not always clear just what is meant by the word penetration in this sense. In 1952, Elliott et al.1 showed that at the end of each tuyere of a blast furnace there is more or less of a void. In this region, coke particles are blown around by the force of the air. This explained the well-known observation reported by Sweetser2 hat if a bar is pushed into a furnace through a tuyere it will go easily into the furnace a distance of some

Jan 1, 1958

By William H. Dresher

The crust of the earth, together with its seas and its atmosphere, is the source of all of mankind's primary wealth. Indeed, most people think of precious metals and stones when they think of wealth mined from the earth, but the value of the material and energy goods derived from the earth far exceed the value of the precious metals and gem stones. Thus, it is obvious that all minerals which we mine from the ground represent new wealth--the copper, clay, or petroleum we mine just as much as the gold or silver. More and more, wealth is defined in terms of utility-not in terms of an arbitrarily established monetary value. The recent action of the OPEC nations in controlling the flow of petroleum has clearly demonstrated this to the petroleum-importing nations! There is developing in the United States, as well as in many other nations of the world, a concern for the future availability of many mineral-derived raw materials and of mineral fuels. Ore grades are diminishing, concern for the environment has placed restraints on commercial development of some mineral deposits and the processing facilities necessary to exploit them, and countries upon which we have relied for major mineral materials have become increasingly nationalistic, causing uncertainties in future supply and causing an increasingly alarming deficit in our nation's balance in trade.

Jan 1, 1980

By M. Gensamer

ALTHOUGH a large number of X-ray photograms of cold-rolled steel have been published, two circumstances have led to the experimental work reported in this paper. The first is that no complete study, making use of the pole-figure method of Wever1, has been made of cold-rolled low-carbon steel. Wever has published pole figures of mild steel sub-jected to plane parallel deformation1,2 and undoubtedly he has applied the method to cold-rolled mild steel, but the authors have not found these data published. Kurdjumow and Sachs3 have applied the method to the study of rolling and recrystallization textures in electrolytic iron; their results will be referred to later. The reason for this dearth of papers using the pole-figure method is obvious; a greater number of photograms and more analytical work (although this work is quite simple and straight-forward) are required to construct a pole figure than most investigators have felt worth while, despite the fact that no other method of which the authors are aware will satisfactorily depict the orientations of the crystal-lites in a polycrystalline aggregate. The second circumstance that led to the work reported in this paper was the appearance of a paper by Wayne A. Sisson4 on the same subject. In his valuable study of the factors influencing the development of pre-ferred orientations in cold-rolled mild steel, Sisson made one observation that required confirmation; that is, that at some stage of the rolling proc-ess the type of preferred orientation changed from the type that gives a photogram characterized as a "six-point" X-ray pattern to that known as a "four-point" pattern. A similar observation had been made by Tam-mann and Heinzel5, who studied the orientations developed in the rolling of steel by the specular reflection of light from the etched surface of rolled samples. These workers also found that the type of preferred orientation

Jan 1, 1936

The cost of power is an important matter to mining companies generally and this thought that the members of the Australasian Institute of Engineers, as well as the engineering and mining professions generally would be interested in any proposal for the reduction of that cost has led to the presentation of this paper.The writer trusts that the description will be found clear and increase the interest in this interesting subject. In the up of the electrical arrangements touched on in this paper, the author has had the able assistance of his friend Mr. Mars, to whom he offers his hearty thanks. The selection of the best class of power plant for a mine is a very difficult and large problem and it is quite out of place to dogmatise that anyone of the many systems that offer is better than another, eg that the all electrical is better than the partly direct steam-driven and partly electrical, or that a gas plant is better than a steam plant. Such a selection is one that calls for very careful and close consideration, in each particular case, of a large number of before it is possible to arrive at a proper decision.

Jan 1, 1912

By Bingliang Gao, Junli Xu, Michal Korenko, Jinzhao Guan, Liangxing Li, Zhongning Shi, Zhaowen Wang, Aimin Liu

Al-Si alloy, a precursor of solar grade silicon, was prepared by direct electrolysis in cryolite molten salt at 950 oC using high purity silica as material, liquid aluminum as the cathode and high purity graphite as the anode. The electrochemical behavior of Si(IV) ion was investigated using cyclic voltammetry method. The electrolysis products were characterized by XRD, SEM/EDS and ICP. The results indicate that the reduction process of Si(IV) on tungsten electrode is a two-step process and there is about 0.6 V gap between the two steps. The contents of boron and phosphorus in the aluminum-silicon alloy are 3 ppmw and 8 ppmw, which will make the directional solidification purification effectively and reduce the cost of preparation solar grade silicon from metallurgical grade silicon.

Jan 1, 2015

By H. Le Chatelier

SILICA brick are indispensable in the manufacture of steel because they alone are able to withstand the high temperature of regenerative furnaces. All attempts to replace silica brick by other refractory materials for this purpose have failed, but the reason for this failure has remained obscure; we shall give an explanation later in this paper. Before the war, silica brick employed in France came principally from abroad, for which reason, since the beginning of hostilities, certain French steel works have been seriously handicapped. Our attention was first directed to the question by M. Bred, Engineer of the Teil Works. With him, we began certain investigations, at first using our laboratory and the furnaces of neighboring steel works. The larger part of our experiments, however, have been made in the laboratory of the Faculty of Sciences at the Sorbonne. For the heating of our samples, we are deeply obliged to MM. Charpy, Yeatmann and Guérineau. In undertaking these studies, our first aim has been to render assistance to French industry, by indicating, as precisely as possible, the necessary conditions for the manufacture of high-grade brick; but at the same time we have intended to give an example of the manner in which scientific methods may be put to practical application in the solution of industrial problems. Although our work has been confined to samples of only a few grams, we are nevertheless convinced that our information can be directly utilized by brick-works of which the output is measured in thousands of tons

Jan 9, 1918

By D. Tang

The froth zone in a flotation cell is recognised as a region which contributes to the overall flotation performance. Froth recovery is a measure of the efficiency with which the froth phase delivers particles arriving at the pulp-froth interface to the concentrate. Poor froth recovery in scavenger stages is generally attributed to poor froth stability. The key indicators of froth performance: froth recovery, entrainment and water recovery were measured in an OK3 pilot cell installed at a zinc concentrator in Australia and supplied with scavenger feed. Cell hydrodynamic and pulp chemical conditions during the operation of the cell were also measured as well as bubble growth across the froth phase. The objective of the work was to assess the impact of a number of commercial frothers on the froth performance in the OK3 cell and assess the suitability of using bubble growth as an indicator of froth stability.

Jan 1, 2014

By Ellis S. Hertzog

The data published in this retort cover only one phase of a special study of tile physical and chemical properties s of only Alabama coals made by the Bureau of Mines. In addition to determinations of friability, the survey included determinations of grindability, B.t.u. value, and ash-fusion temperature. Assay distillation tests, both for high- and low-temperature carbonization, and proximate and ultimate analyses were made also. However, this preliminary paper is concerned only with the results of friability tests and is issued to expedite the release of this information to the public. The friability, test measures the liability of a coal to break into smaller pieces when subjected to repeated handling, as occurs in the mining, preparation, and transportation operations. Friability depends on many physical characteristics of the coal that vary not only between different seams but also in the same seam. The laboratory methods of determining friability have been developed to give a practical means of estimating degradation of size. So far as is known to the authors, no data on the friability of Alabama coals have ever been published. This caper makes available for the first time fairly comprehensive3 information on this subject. Because the procedure for the tumbler test for determining the friability of coal is relatively new to the coal operators, the authors Lave included a, complete description of it in this report.

Jan 1, 1938

By H. l. Burghoff, E. C. Bohlen

The work reported in this paper was carried out to supplement the existing information concerning directional properties and recrystallization textures of annealed brass sheet and strip. These characteristics are of direct interest when the forming and drawing properties of such material are being considered. Among those who have made contributions in this field are Bass and G1ocker;l Bauer, Göler and Sachs;2 Phillips and Samans;3 Pratt;4 Price;5 Cook;6 Richards;7 Brick;8 and Brick and Williamson.9 These investigators have found, in general, that in brass strip that shows directional variations in properties, tensile strength has a minimum value and elongation has a maximum value at 45' to the rolling direction. The most pronounced directional properties have been found in material given the greatest reductions in rolling followed by high annealing temperatures. Recrystallization texture of brass has been variously reported as (II3)[II2], (ooi)[ioo], and a combination of (II0)[II5] and traces of the primary rolling texture, (110)[112]. The directional studies have been very informative, but actual tests appear to have been confined to material in its final condition. Tests at intermediate stages have received little attention although previous history of some materials has been partly considered. Perhaps the most comprehensive investigation was made by Cook,' who studied the directional properties of 70-30 brass strip for which the final and penultimate, or next to the last, anneals and the final reductions were varied. He found that, for any given combination of penultimate anneal and final reduction, the tendency toward the development of directional properties was reduced as the temperature of the final anneal was decreased. In addition to drawing cups and making tensile tests of the finished material at various angles to the rolling direction, he measured the frequency and the angles of twins in grains for several specimens. Plots of his twin counts showed directionality for the materials that produced eared cups. Test Materials and Equipment For this investigation, one commercial heat of 68-32 brass was cast in the form of bars for cold-rolling, I31/2 in wide and I1/2 in. thick. The analysis was as follows: 68.83 per cent copper, 0.04 per cent lead, 0.01 per cent iron, 31.12 per cent zinc (by difference). The bars were so processed to the final thickness, 0.020 in., as to obtain on this thickness all possible combinations of the variables listed below except those involving the sequence of 84 per cent penultimate reduction and 84 per cent final reduction: I. Penultimate reductions of 37 per cent, 50 per cent and 84 per cent; 2. Penultimate anneals at 800°, 900°, 1050° and 1200°F.; 3. Final reductions of 37 per cent, 50 per cent, 69 per cent and 84 per cent;

Jan 1, 1942

By E. C. Bohlen, H. l. Burghoff

The work reported in this paper was carried out to supplement the existing information concerning directional properties and recrystallization textures of annealed brass sheet and strip. These characteristics are of direct interest when the forming and drawing properties of such material are being considered. Among those who have made contributions in this field are Bass and G1ocker;l Bauer, Göler and Sachs;2 Phillips and Samans;3 Pratt;4 Price;5 Cook;6 Richards;7 Brick;8 and Brick and Williamson.9 These investigators have found, in general, that in brass strip that shows directional variations in properties, tensile strength has a minimum value and elongation has a maximum value at 45' to the rolling direction. The most pronounced directional properties have been found in material given the greatest reductions in rolling followed by high annealing temperatures. Recrystallization texture of brass has been variously reported as (II3)[II2], (ooi)[ioo], and a combination of (II0)[II5] and traces of the primary rolling texture, (110)[112]. The directional studies have been very informative, but actual tests appear to have been confined to material in its final condition. Tests at intermediate stages have received little attention although previous history of some materials has been partly considered. Perhaps the most comprehensive investigation was made by Cook,' who studied the directional properties of 70-30 brass strip for which the final and penultimate, or next to the last, anneals and the final reductions were varied. He found that, for any given combination of penultimate anneal and final reduction, the tendency toward the development of directional properties was reduced as the temperature of the final anneal was decreased. In addition to drawing cups and making tensile tests of the finished material at various angles to the rolling direction, he measured the frequency and the angles of twins in grains for several specimens. Plots of his twin counts showed directionality for the materials that produced eared cups. Test Materials and Equipment For this investigation, one commercial heat of 68-32 brass was cast in the form of bars for cold-rolling, I31/2 in wide and I1/2 in. thick. The analysis was as follows: 68.83 per cent copper, 0.04 per cent lead, 0.01 per cent iron, 31.12 per cent zinc (by difference). The bars were so processed to the final thickness, 0.020 in., as to obtain on this thickness all possible combinations of the variables listed below except those involving the sequence of 84 per cent penultimate reduction and 84 per cent final reduction: I. Penultimate reductions of 37 per cent, 50 per cent and 84 per cent; 2. Penultimate anneals at 800°, 900°, 1050° and 1200°F.; 3. Final reductions of 37 per cent, 50 per cent, 69 per cent and 84 per cent;

Jan 1, 1942

By Howard D. Jacobs

A bulk sample of oxidized taconite taken from the western Mesabi Range was evaluated by the Bureau of Mines using the Bureau-developed selective flocculation-desliming-cationic (or anionic) flotation process. The raw ore sample containing 32.3 pct Fe was treated by both cationic and anionic flotation. Using the cationic system the concentrates averaged. 37.2 wt-pct of the feed and contained 62.8 pct Fe and 4.7 pet Si02 with an iron recovery of 72.3 pet. With the anionic system, concentrates averaged 37.7 wt-pet of the feed and contained 63.0 pct Fe and 5.3 pct 8i02 with an iron recovery of 73.5 pct. A comparison of reagent costs showed that the cationic process cost 144.1 cents per long ton of crude ore and the anionic process 178.7 cents per long ton of crude ore. Reclaimed water comprised 86 pct of the total water requirement for anionic flotation and 88 pct for cationic flotation. The ore used in this study was one of three samples representing about 3.25 billion tons of oxidized taconite containing from 32 to 36 pct feed iron. Previous study had indicated that selective flocculation-desliming-cationic flotation would produce concentrates from the other two samples of 61.7 pct Fe and 5.1 pct Si02 at 67-pct Fe recovery, and 63.5 pct Fe and 4.3 pet Si02 at 8S-pct Fe recovery. By developing a successful treatment for these ores, the Bureau has insured the availability of technology for processing an amount of raw iron ore which, by itself, would supply U.S iron needs for 50 to 75 years at expected consumption rates.

Jan 1, 1981

By Turgay Gurun

"Digital simulation can be used as an analytical tool to optimize the design of crushing plants without need for large-scale experimental programs.General mathematical description of a crushing operation permits the simulation of a crushing plant flowsheet under various operating conditions. The process model encompasses multistage open- and closed-circuit crushing of hard and soft rock. Crushing balances are analyzed in the light of crusher and screen performance and a comparison of different closed-circuit arrangements is made in terms of process and layout criteria.The simulation model allows comparison of process alternatives to be made in terms of equipment selection and capital and operating cost estimation. It thus provides the pertinent practical information to maximize plant efficiency, and to minimize expenditures in such items as equipment, structures, power consumption, and so on."

Jan 1, 2014