Search Documents

By R. J. Brison, R. D. MacDonald

This chapter is written primarily from the standpoint of development of flotation processes for treatment of specific ores. However, most of the principles and techniques discussed are equally applicable to other forms of applied flotation research such as improvement of procedures in existing plants and development of new reagents or methods without reference to specific ores. Because it is not possible to cover this subject in detail here, much of the material presented is in the form of a guide to the literature, with emphasis on readily available, English language publications. Details are included only if considered to be widely applicable or not readily accessible in the literature. Related subjects which are covered elsewhere in this volume, such as flowsheet design and statistical techniques, are not emphasized in this chapter. The material presented is intended primarily for those familiar with the theory and practice of flotation, but with limited experience in applied flotation research. It may be of value to the experienced investigator as well, by calling to his attention some useful viewpoints or techniques that he may have overlooked. It has often been said that flotation is more of an art than a science. In- deed much of the knowledge of flotation behavior is empirical. However, the unsystematic, artisan approach to flotation problems results only in an ac- cumulation of unrelated data. Like any other physical or chemical process, flotation is amenable to investigation by systematic experimental methods. The experiments should be based, as far as possible, on an understanding of the natural laws that govern the process and on good experimental procedures. SAMPLING OF A DEPOSIT In working out a flotation process for a mineral deposit, no step is more important than that of obtaining a suitable sample or samples. Experimental procedures cannot compensate for the lack of a representative sample. Methods of sampling a deposit have been published elsewhere,l-4 but a few points are of special importance from the standpoint of flotation. First, the sample should be representative of the deposit, not only in respect to chemical composition, but also in respect to mineralogical composition and degree of dissemination of the valuable minerals. To help ensure

Jan 1, 1962

By L. W. Holm, A. K. Csaszar

A series of laboratory experiments was conducted in which oil was displaced from a porous medium by water-driven slugs of alcohols or similar solvents. The solvents used were soluble to some degree in both oil and water and covered the range of solubilities from complete solubility in oil to complete solubility in water. Displacement experiments were conducted on 2-and 3%-in. in diameter consolidated cores and 1-and 2-in. in diameter unconsolidated sand packs. The cores and sand packs ranged in length from 1 to 30 ft, and they were saturated with brine and crude or refined oils. The solvents used included ethyl alcohol, isopropyl alcohol (IPA), tertiary butyl alcohol (TBAI, secondary butyl alcohol (SBA), n-amyl alcohol (NAA), methyl ethyl ketone, acetone and others. It was found that all of the oil present in a porous medium could be miscibly displaced by injecting a slug of mutual solvent and driving it with water. The oil-recovery efficiency was dependent upon (1) the relative solubilities of the solvent in oil and water, and (2) the distance traversed by the flood. For complete oil recovery from cores, a smaller amount of a preferentially oil-soluble solvent was required, compared to the amount of preferentially water-soluble solvent needed. The size of the solvent slug required varied inversely with the linear flooding-path length raised to the 0.65 power. Water-driven dual solvent combinations (an oil-soluble solvent slug followed by a water-soluble solvent slug) were found to effect complete oil recovery with less total solvent than any single solvent used. In these dual-solvent displacement experiments, the slug size required varied inversely with length raised to the 0.55 power. Based upon the experimental results, a theory was developed to describe the displacement of oil and water by mutual solvents, and equations are presented to predict the production history in a linear system. These equations take into account the properties of the solvents and the porous medium. INTRODUCTION Oil-recovery processes which utilize displacing fluids that are miscible with the reservoir fluids have been studied extensively in recent years. Because of the poor contact efficiency and high pressure requirements of the LPG-gas displacement process there has been considerable interest in the alcohol-water process, and a number of studies have been made on the recovery of oil through the use of solvents which are mutually soluble in oil and water. An investigation by Sievert, Dew and Conleyl indicated that the use of mutual solvents would be limited because the presence of water in a porous medium would cause a phase break in the leading edge of the displacing solvent. Their study also showed that, in consolidated cores containing. only oil, the displacement of oil by a water-driven mutual-solvent slug of tertiary butyl alcohol (TBA) was affected by the viscosity ratios of the fluids involved. Gatlin and slobod3 concluded that an isopropyl alcohol (IPA) slug acts as a miscible piston, completely displacing both oil and water until the alcohol content of the mixing zone falls below the concentration necessary to maintain miscibility. Their study was conducted on uniform unconsolidated sand packs. They concluded further that IPA could be used effectively to recover oil from a watered-out sand. In a paper by Taber, Gamath and Reed4 relating an investigation on sandstone cores, it was stated that the displacement of oil by mutual solvents, particularly IPA, was not a miscible displacement and that no improvement in efficiency could be expected with increase in flooding-path length. However, their analytical analysis of the displacement mechanism using TBA is, in fact, one which indicates that the displacement is controlled by miscible mixing. They suggested that the lack of improvement in efficiency with flooding - path

By Floyd Varley

In deep and highly-stressed coal mining, advanced design practices are used to minimize the potential for damaging events to occur. Despite these design efforts, the hazard of coal mine bumps can not be completely eliminated. This paper will review current and historic work practices used internationally to minimize the hazard to miners from mining in conditions which could produce a bump. These site specific work practices have a common base in monitoring for conditions which could result in a bump and application of controls to prevent the occurrence or minimize the severity of an event where miners are working. Monitoring practices range from purely observational to semi quantitative. Control methods attempt to initiate events in a controlled manner, absorb the energy of a potential event or reduce the potential for or magnitude of an event by altering the stress conditions of the mine workings. Building from the experiences of other coal fields, an empirical framework to manage the potential hazard of coal mine bumps can be developed to enhance the level of safety provided by prudent mine design.

Jan 1, 2008

By Emil Szaks

[A great number of papers have been presented at various Engineering Society meetings on the Unit Train subject. Moat are descriptions of facilities that have been constructed or are abort to be built. Many describe the facility as being the World's fastest, newest, largest, incorporating the latest technology and so forth, Many are duplications of installations that have been recently constructed, sort of carbon copies but perhaps arranged differently. The trend has been to incorporate loop tracks, rotary dumpers, indexers and, of course, the snivel coupler equipped unit train. How that the energy crisis has increased the use of coal, there has been a tremendous Increase in applications for permits to construct rail to river coal loading facilities. This paper is different. It does not describe any single existing facility, but is given to alert prospective terminal owners and engineers that there are items that require considerable study and evaluation beside merely selecting an indexer, car dumper, stacker, ship or berg loader and so on. An important item is the selection of the railway car which in turn can affect the selection of the method of loading and unloading. Let us list a few of the items that should be considered and discuss the areas that require examination:]

Jan 1, 1979

By Daniel C. McLean

Chemistry plays a more important role in milling operations than is generally recognized, particularly in fluid- solid separation processes. Chemical aspects are also very important insofar as plant water quality is concerned, and in the manner in which this water quality effects plant design and operation. Aside from the inherent chemical characteristics of plant water, the mineral preparation industry is becoming increasingly more dependent on the use of mining chemical reagents--relatively new to the coal industry, but items of I standard usage in complex metal recovery plants. These chemicals have many useful properties and can produce significant improvements in operations and metallurgical efficiencies when used properly and intelligently. They can produce poor results and sometimes severe losses when used improperly. Most reagents are relatively expensive on a per pound basis, hence costs can be excessive if they are used wastefully or inefficiently.

Jan 1, 1968

By Seth C. Schaefer

The Bureau of Mines studied thermodynamic properties of Al-Ni alloys con¬taining 0.54 to 30.04 atomic percent nickel with the aid of the high-temperature galvanic cell Al(1) // Al+3 (AlCl3 in NaCI.KC1) // Al-Ni alloy (1 or s). Activities of aluminum and nickel (compared with pure liquid metals as the standard state) show pronounced negative deviation from Raoult's law at 1,273 K. The properties [?G, ?Gxs, ?G ideal, ?GA1, AGxs1, ?Gni , and ?GNixs] have been derived from the experimental data and are summarized in tables and illustrations. At 1,127 K, the thermodynamic stability for the invariant three-phase equilibrium consisting of a saturated liquid, A13Ni, and A13Ni2 has been uniquely defined by an activity for aluminum of 0.751. A free energy of formation at 1,127 K of -7,940 cal/g-atom was derived for the compound A13Ni.

Jan 1, 1975

By Murray Udy

La Corporación Venezolana de Guayana ( CVG) decidió renovar su noveno horno eléctrico de reducción a través de un nuevo proceso para la fabricación del fierro Strategic-Ud. En este sentido, el presente artículo señala la la instalación de este nuevo proceso de producción de hierro en la planta siderúrgica del Orinoco. La implantación del Strategic-Udy se inició en 1963 y es una combinación de operaciones unitarias conocidas con una técnica operativa mejorada, a fin de ofrecer mejor control sobre los procesos químicos e incrementar la eficiencia de la técnica antigua. Asimismo este nuevo proceso, elimina las limitaciones de tamaño y calidad del material impuestas en los procesos existentes para la fabricación del fierro.

Jan 1, 1964

By Y. J. Wang

This paper describes a procedure for solving the generalized system of n network equations in n unknowns considering the following ventilation variables and parameters: (a) air quantities, (b) pressure losses or gains caused by the control devices (i.e., fans or regulators), (c) resistance factors, (d) natural ventilation pressure, and (e) fan pressures (as a function of air quantities). The air quantities and pressure losses for all branches in the network are grouped into dependent and independent variables. The branches with an independent quantity are contained in a chord set, and the branches with a dependent pressure loss are contained in a chord set. In addition to the problem formulation, the solution procedure, applying the Newton method, is discussed and illustrated with a numerical example.

Jan 1, 1989

R. H. Sweetser, Sault Ste. Marie, Ont. (communication to the Secretary*):—The recent work of furnace No. 1 of The Algoma Steel .Co., at Sault Ste. Marie, Ontario, using for fuel, first all charcoal, then a mixture of charcoal and coke, and finally all coke, upsets the estimates given by Mr. Hall in the last two paragraphs of his interesting paper. Furnace No. 1 was built for a charcoal-furnace, and it was run on charcoal fuel from March 6 until July 9, 1905; then, for a week, a mixture of charcoal and coke was used, and, since then, coke alone has been the only fuel. It is to be regretted that at no time, during the run on charcoal, was there enough charcoal on hand and " in sight" to warrant blowing the furnace as hard as it should have been blown. During April and May the supply of charcoal limited the amount of blast to about 8,000 cu. ft. of air per min.; in June, to about 8,900 cubic feet. For a few days in July about 10,000 cu. ft. were blown, and then the maximum daily output, 173 tons (2,240 lb.), was reached. At all times the quality of the charcoal was poor, having been made from wood cut from three to four years before. Doubtless this furnace could have produced 200 tons of iron per day, even with this quality of charcoal, provided the supply had been sufficient; and with

Jan 1, 1906

By Camier R. J, Perry G. J

Extensive deposits of brown coal exist in the Gippsland Basin, primarily in the Latrobe Valley. The total quantities of economically winnable coal in this region of Victoria and in other smaller fields are large enough to adequately assure Victoria's future electricity needs and to also provide large quantities for alternative applications, including liquefaction. As a result of the recent conflict in the Middle East attention has again been focussed on the production of synthetic fuels from coal. There have been many investigations over the years into the production of oil from Victorian brown coal. The purpose of this paper is to summarise the scope, objectives and major findings of these studies, with the emphasis on the direct hydrogenation route for converting brown coal to oil. The principal alternative processes are carboniastion and hydrotreatment of the product tar, or gasification and Fischer Tropsch synthesis of liquids from the product gas. The attractions of Victorian brown coal which have encouraged these studies include: ò the vast reserves of Victorian brown coal and the favourable conditions for low cost mining, ò the high quality of the coal (low ash, sulphur and nitrogen contents), ò the high reactivity of the coal giving high yields of product in hydrogenation to liquid fuels, ò the extensive data base available on the resource and its characteristics, and ò the availability of a skilled workforce and extensive infrastructure in the Latrobe Region to support a major resource development project. These advantages have been partially offset by: ò the high moisture content of the brown coal and the cost of drying, and ò the priority previously given to electricity generation in the allocation of the brown coal resource.

Jan 1, 1992

By Rajendra K. Devala, Sukumar Bandopadhyay

In order to be able to design an adequate mine ventilation system it is necessary to understand how pollutant masses disperse into turbulent ventilation air streams. The mixing of gases and dusts with ventilating air, and dispersion of these pollutants in mine airways, are important flow or transfer problems. For the solution of such problems, the finite difference technique is often used. In this paper, numerical approximation schemes for the solution of the mass transfer problem have been developed using several explicit finite difference schemes. Results from these schemes have been compared with the analytical solution for spatial and time increments using the concept of Root Mean Square error. The comparison of various schemes reveals that the explicit finite difference schemes analyzed here give more accurate results at lower velocities, though the results are dependent on the spatial and time steps considered. At higher velocities the schemes tends to oscillate about the analytical solution. INTRODUCTION In mining, most of the mine air pollutants, such as respirable dust, methane, blasting fumes and diesel exhaust, are produced at the mine face and in haulageways. Injection of any of these pollutants in the mine ventilating air causes disturbances of the equilibrium state of the pollutant concentration of the ventilating air. The mixing of these gases and dusts with the ventilating air are typical examples of mass transfer processes. Pollutants are diluted by the stream of ventilating air flow along airways and discharged into the outside atmosphere of the mine through a return shaft. The dispersions of these pollutants in mine airways are important flow or transfer problems. Knowledge about pollutant sources, emission and transport of these pollutants are essential for ventilation planning and design to ensure good engineering control over air quality, quantity, and environmental conditions. Modeling of mass transfer phenomena in mine ventilation is largely based on extensive studies of turbulent dispersion in wind tunnels and the lower atmosphere of the earth. The general approach in the formulation of models lies in the recognition that these mass transfer phenomena can be conceptualized as a flow problem that can be solved by the general application of Taylor's theory (1954) of turbulent flow and diffusion with modification appropriate static and dynamic parameters. If the face zone is initially contaminated by a pollutant over a long section (e.g. instantaneous exposure of large gas accumulation, rapid methane release etc.), the process of decontaminating the mine workings can be regarded as displacement and diffusion of the tailing edge of the cloud of contaminates in the form of a semi-infinite gas body, for which a one-dimensional mass transfer equation is represented by: [at + u • ax = Ex ex2 + f (x,t)(1.1)] In Eq. (1.1), the term [~~] is the rate of growth of the concentration in the differential element, while a [(5xx )] is the net gain of material due to convective transfer. The two terms balance the total loss of material due to turbulent dispersion that is represented by [Ex . 21] and f(x,t), the source term for the pollutant in the roadway. Several cases of mass transfer that occur in mining can be identified and modelled using the conservative volume element method. The governing equation, along with the associated boundary and initial conditions, source terms and their solutions are detailed elsewhere (Bandopadhyay and Ramani, 1988, Devala, 1989). Only one mass transfer situation is presented (Figure 1) here for the present analysis. Mixed Evolution of Pollutant (multiple pulses) Typical examples of these situations are emission of pollutants from multiple diesel vehicles in the face area, and gas emission from standing pillars as well as from broken coal seam during coal cutting with a continuous miner. The mathematical statement of the problem along with the initial and boundary conditions are given below, Governing Equation: [do+u- =E d2c(1.2) ataxx dx2] Initial conditions:

Jan 1, 1993

By Sergio Castro, Janusz Laskowski

In the flotation in highly concentrated electrolyte solutions not only ionic strength but also chemical composition, flotation pH and mineral properties play an important role. As a result an improvement or depression may be observed. A strong improvement in the floatability of hydrophobic bituminous coals and other inherently hydrophobic minerals is characteristic for the "salt flotation process", which is carried out in concentrated electrolyte solutions at natural pH and without addition of any flotation reagents. However, pH is a key factor when saline and hipersaline waters with hydrolyzing metallic ions are used as process water. In the case of flotation of Cu-Mo sulfide ores in seawater, molybdenite is strongly depressed by the Mg2+ hydrolysis products when pH is raised to depress pyrite. Process water with a high content of Mg2+ and Ca2+ ions, and this also includes seawater, have deleterious effect on the anionic flotation of industrial minerals with fatty acids. The flotation of potash ores is carried out in NaCl-KCl saturated brine (6-7 mole/L of NaCl and KCl) with the use of long-chain amines. Such a high electrolyte concentration changes dramatically the amine Krafft point making the collector insoluble in brine; its mode of action entirely differs from that in conventional flotation processes.

Jan 1, 2014

By Ralph Wilcox

The diamond drilling of certain characters of unstable rock formation, as, for example, the copper-bearing schists of the Miami district in Arizona, is rendered most difficult by what is known as a caving " of the sides of the drill holes. As this caving is very greatly increased by the action of flowing water, it occurred to me, after experiencing a great deal of difficulty with caving in diamond-drill holes which I was drilling for the Miami Copper Co., that if I could substitute air for water, much of the caving—with resultant difficulties, such as decreased speed of sinking and increased consumption of diamonds—would be overcome. After some experimenting, I found that it was perfectly practicable to substitute air for the water; forcing the air down the hollow rotating rods in the same manner as is done with water, the air passing out around the bit, which is thus cooled, and ascending on the out~ide of the rods to the collar of the hole, carrying the borings in just as satisfactory a manner as had been done by the water, but without the accompanying destruction or caving of the sides of the drill holes such as had been so generally experienced with the water. When water was encountered in the drilling this water was forced up to the collar just as it would have been had water been used in the drilling, but with the correspondingly decreased flow there was relatively less washing or caving of the sides of the drill holes. The only change necessary in the arrangement of the drill is that a cross instead of a tee is used at the collar of the hole. A tightly woven jute bag is attached to one arm of the cross, for collecting and filtering the sample; and when drilling in dry ground a jet of water is attached to the opposite arm of the cross, to collect the dust and wash down the sample into the bag. The rods rotate through a stuffing box attached to the upper opening of the cross. The distention of the jute bag by the issuing air indicates the operating conditions as sufficiently as did the flow of water when using water in the drill hole. The small percentage of core recovery rendered it necessary to

Jan 1, 1914

By Brian Sandhuas, Robert McClure

All flyrock incidents have the potential to result in injuries or fatalities that can result in loss of company reputation, license to operate with clients, and bear the exposure to high cost liability. From 2007 to 2009, one North American Quarry and Construction Business experienced a series of flyrock incidents. In the spring of 2009, this business declared that the frequency and severity of Flyrock Incidents had reached an unacceptable level. A Flyrock Elimination Program was launched.

Jan 1, 2012

By M. Ndabeni, J. H. van Vreden, M. Le Roux, Q. P. Campbell

It is not uncommon for gold slurry ponds or screen oversize dumps to contain several different types of carbon-rich contaminants. These contaminants act as robbers of dissolved gold which has a detrimental effect during the downstream carbon-in-leach (CIL) or carbon-in-pulp (CIP) processes. With a renewed interest in the reprocessing of contaminated gold waste ponds and dumps, preconcentration of the feed to either the CIL or CIP process becomes important to maximise profits from these resources. An added advantage in removing these resources, which were once thought of as being uneconomical, is the availability of land that can further be rehabilitated for community development projects. For gravity separation, an example of suitable technology is the Reflux Classifier (RC), which can be used for the separation of materials of different densities and can be used as a pre-concentration step. In this project, a laboratory-scale Reflux Classifier was used to pre-concentrate a gold-bearing sample obtained from a waste dump situated to the east of Johannesburg, South Africa. The material had an average gold grade of 1.9 g/ton and a carbon content of 10%. This material was first fed to a semi-batch Reflux Classifier that was used to fractionate it into several different density intervals by varying the fluidisation water feed rate, followed by continuous runs at fixed water flow rates. The results showed that a cumulative gold recovery of 60%, carbon recovery of 85%, and mass pull of 41% was possible for a fluidisation water feed rate of 15 L/min, while a rate of 20 L/min resulted in a gold recovery, carbon recovery and mass pull of 83%, 92% and 79% respectively, which translated into a concentrate gold grade above the set target of 3 g/ton. Continuous operation at 20 L/min yielded an underflow stream with 84% gold recovery at a grade of 5.4 g/ton. Keywords: Reflux Classification, gold recovery

Jan 1, 2020

By W. G. SWART

THE best estimate on reserves of iron ore in the Lake Superior district is that made, in 1920, by Mr. R. C. Allen, amounting to 2,947,225,000 tons of assured and probable ore. This includes direct- shipping or so-called merchantable ores, and those capable of beneficiation by demonstrated processes. De- ducting from this the 287,000,000 tons shipped since 1920, leaves a present reserve of approximately 2,500,- 000,000 tons, or; about 50 years' supply. The assured ore in this estimate is given as 1,560,500,000 tons, which checks Mr. Lake's estimate of 1,528,948,000 tons, or about 30 years' supply. This is not a long time in the life of the steel industry, and it can be readily appreciated that the matter is important enough to war- rant the attention it is beginning to receive. The first question that engages our attention is, What is merchantable ore? In 1902 the average of all Mesabi shipments was 56.07 per cent iron and 4.35 per cent silica. Twenty-five years later it had dropped to 51.99 per cent iron, with silica up to 7.92 per cent. It has remained around these figures for' ten or twelve years and, except for a probable rise in silica, can stay there for an indefinite period. Most of these figures I am giving cover the Mesabi Range. Including the other ranges does not change the figures greatly, and the Mesabi Range commands the situation, since it produces about 65 per cent of the total annual tonnage and, according to Mr. Allen, contains 81 per cent of the assured reserves, 50 per cent of the probable reserves, and 66 per cent of both the assured and the probable reserves.

Jan 1, 1926

By P. D. Frost, H. A. Robinson, J. R. Doig, M. W. Mote

The mechanism of hardening in heat-treatable zirconium alloys was foUNd to be analogous to that for titanium alloys. Zirconium containing a relatively large addition of a ß -stabilizing element such as molybdenum or columbium can be hardened by the following transformation: Lean alloys, having insufficient alloy content to retain ß at room temperature are hardened by the following transformation: Application of these findings in Zr-Mo-Sn and Zr-Nb-Sn alloys produced strengths as high as 190,000 psi with reasonable ductility. PRIOR research on zirconium alloys has been concerned with development of greater strengths and creep resistance by solid-solution hardening or by dispersion hardening. Although solution and aging heat treatments had been applied earlier to zirconium alloys, quenching frequently produced low ductility. The possibility that the ß-to-w transformation, discovered earlier in titanium alloys,' might also occur in zirconium alloys and cause low ductility was considered, and, indeed, was found as predicted2 to be the case. In the earliest experiments, the heat-treatment response of titanium, too, was disappointing. However, by avoiding the formation of the embrittling w phase, it became practical to obtain room-temperature strengths higher than 180,000 psi, with elongation values of 10 pct.3 Based on the present concept of titanium heat treatment, the principal requirement for a heat-treatable zirconium alloy is that it contains a certain minimum amount of one or more ß -stabilizing elements. Only molybdenum, columbium, and tantalum, when present in sufficient amounts, are known to stabilize ß zirconium to room temperature during rapid cooling from the ß field. Tantalum was undesirable because of its high thermal-neutron cross section. Aluminum and tin are effective a stabilizers, but aluminum has been shown to seriously decrease the corrosion resistance of simple zirconium alloys in hot water. Therefore, for the present study, tin was used as the stabilizer addition. The alloys selected for this evaluation are presented in Table 1 along with their analyses and ß-transus temperatures. The analyses indicated that intended compositions were usually realized. EXPERIMENTAL PROCEDURES All of the alloys were melted from sponge zirconium and fabricated to sheet for heat treatment

Jan 1, 1960

By Robert Hopler

Of the common causes of the larger mine accidents, such as falls of roof and coal, gas and dust explosions, mine fires, and the misuse of explosives, all of which are often closely related, each must be studied and fought in a manner peculiar to itself. The last mentioned, the misuse of black powder and other explosives, is sometimes considered the least important of these causes of mine accidents; but its importance is much greater than the statistics indicate, for the reason that the misuse of explosives is the true cause of many of the fatal mine fires, gas or dust explosions, and falls of roof that are credited to other causes.

Jan 1, 2012

By J. R. Bartels

Operation of underground coal mine mobile equipment is usually done in a restricted workspace with reduced visibility. This work environment puts machine operators in awkward postures for tasks that require awareness of their surroundings and fast reactions to avoid hazardous situations. Using experienced equipment operators as a source, researchers conducted an investigation that developed a method to gather data on the needs and practices of machine operators while controlling the machine and the reasons for needing particular operational cues. The method used was an interview technique including a survey questionnaire and visual aids. The data gathered defined operator cues and work positions for the cutting and tramming phases of remote controlled continuous mining machines used in underground coal mines. Analysis techniques to determine which cues an operator sees from a variety of positions utilizing a computer simulation is shown to be potentially useful to the mining industry for design of work practices and workplace layout and could impact equipment design and selection for improved worker safety. Conclusions indicate that the survey was a good research tool to collect data and helped investigators understand important visual cues. Using this information, researchers were able to analyze the visual cues an operator can see from a given work position and posture.

Jan 1, 2009

By J. Robert Denny

The impact of the computer revolution--so pervasive in some industries--has been less startling in the mining industry. Computer techniques have been used successfully to provide drill hole calculations, contour maps, and a variety of conventional maintenance scheduling, and accounting applications. But it is our experience that the real economic payoffs lie in the engineering application of computers to mine planning and the use of systems engineering techniques for mine operations. Since 1964, Newmont Mining Corporation has been engaged in systematic research and development of computer techniques in a variety of mine planning applications. The general objective in using computers has been twofold: first, to arrive at a viable, near-optimum plan for mining a particular orebody, and second, to decrease the financial investment by reducing the man-hours required for mine planning. Three major phases in the evolution of these computer techniques for mine planning are discernible. In phase one, the machine capability for duplicating manual drafting and contour mapping was developed. The necessity of including all recognized geologic characteristics is obvious. Capability for properly incorporating structure, stratigraphic trends, and other geological features was a significant aspect of phase one development.

Jan 1, 1970