Search Documents

By Y. Mitani, F. Vallier, T. Esaki

Shear-flow coupling tests are conducted using an original apparatus, and a shear-flow coupling model using Geographic Information System (GIS) is developed in order to evaluate shear-flow coupling properties of a rock joint. Shear-flow coupling tests indicate that the hydraulic conductivity of joint once decreases, and then rapidly increases at the shear displacement near the peak shear stress. The proposed model simulates the test results relatively well. However it indicates that it is difficult to apply the local ‘cubic law’ model in the initial shear stage, in which the change of selective flow path is remarkable. Scher-Fliess-Kopplungsversuche werden mit einem neuartigen Versuchsgerät durchgeführt und mithilfe von Geo-Informationssystemen (GIS) gedeutet, um so ein Modell für die Scher-Fliess-Kopplung in Gebirgstrennflächen zu entwickeln. Die Versuche zeigen, dass die hydraulische Leitfähigkeit zuerst abnimmt, dann aber schnell wieder zunimmt sobald die maximale Scherfestigkeit erreicht ist. Das vorgestellte Modell bildet die Testergebnisse relativ gut nach. Es zeigt auch, dass es schwierig ist, das lokale Cubic Law im Initialstadium der Scherbeanspruchung anzuwenden, in dem die Variationen selektiver Fliesswege gross ist. Les essaies hydro-mécaniques couplés en cisaillement sont réalisés grâce à un appareil éxperimental prototype et un modèle de couplage hydro-mécanique utilisant le S.I.G (systeme d'information géographique) développé dans le but d'évaluer les propriétés hydro-mécaniques des joint rocheux. Les résultats indiquent que la conductivité hydraulique des joints décroit puis augmente rapidement en se rapprochant du pic de cisaillement. Le modèle proposé simule relativement bien les résultats expérimentaux ; mais indique également qu’il est difficile d’appliquer localement la loi cubique au début du cisaillement où, les changements d’orientation dans le réseau d'écoulement sont considerables.

Jan 1, 2003

By Peter Fischer

Between 45,000 and 50,000 claims for subsidence are submitted each year to the German hard coal industry. In order to improve the service to claimants a quality management was established in 2005. This paper describes the process now used for handling these claims. A quality check has also been carried out by way of a customer survey, which was performed by an independent research agency. The results of the survey are presented in this paper. In Germany, research into mining subsidence mainly involves the prediction of ground movements caused by deep mining operations. Special areas of research are subsidence reducing aspects of the extraction panel planning, especially from the point of view of mining dynamics, as well as securing and restoration measures. This work seeks to prevent or minimize mining-induced damages close to the surface, for instance, buildings or infrastructure installations (such as pipelines), or underground mine openings (e.g. shafts). Roof collapses and surface fractures caused by shallow mine workings of an earlier era currently constitute a special area of investigation.

Jan 1, 2006

By Arthur Phillips, E. N. Skinner

DURING the course of an experimental program concerned with the hydrogen embrittlement of copper containing oxygen in concentrations within the solubility limits it became necessary to make a critical appraisal of the literature dealing with the solubility relationships of oxygen and solid copper. The latest determinations, and perhaps the only data obtained on "spectroscopically" pure copper, are those of Rhines and Mathewson1 who reported that the solid solubility increases from 0.007 per cent oxygen at 600°C. to about 0.015 per cent at 1050°C. Hanson, Marryat and Ford2 had previously placed the solubility limit at less than 0.009 per cent oxygen at 1000°C. and Allen and Street3 had suggested, on the basis of an unpublished research by T. Hewitt, not over 0.005 per cent oxygen at 500°C. In the introductory stages of the investigation indirect evidence accumulated to suggest that the solubility limits were significantly lower than those previously reported. For this reason it was deemed essential to clarify this point before proceeding with a program intended to establish a quantitative relationship between hydrogen embrittlement and oxygen concentrations positively known to be within the solid solution range. Furthermore, the increasing production and the highly selective applications of the commercial "oxygen-free" coppers inevitably direct attention to the practical necessity for exact knowledge regarding the effects of minute concentrations of the elements ordinarily found in the high-purity coppers now available. Of these elements oxygen occupies a unique position, not only by virtue of its specific effects on copper but more particularly in view of its important reactive tendencies toward the other impurities with which it is associated. Rhines and Mathewson considered several methods for measuring the solubility of oxygen and finally adopted the simple plan of saturating the specimens, obtained from redeposited cathode copper, by heating at the desired temperature in air. After the removal of surface oxide by mechanical and chemical means, the oxygen content was determined in the underlying metal. In general, this process of saturation, with a few modifications, was followed by the present writers. Although the procedure is direct and has obvious advantages, its effectiveness, unfortunately, is reduced by an excessive scaling of the copper, particularly at the higher temperatures. After saturation treatments above 900°C. the writers found that the specimens, necessarily rather thin in the original condition, consisted largely of scale and yielded too little metal for a satisfactory analytical sample. Furthermore, great difficulty was experienced in effecting complete removal of the scale. Needless to say, it is necessary to exercise extraordinary care in the preparation of the surface of the analytical sample in order to eliminate submicroscopic fragments of cuprous oxide which ordinarily are lodged in the crevasses and

Jan 1, 1941

The 1997 Rapid Excavation and Tunneling Conference (RETC) was held at the Mirage Hotel, Las Vegas, NV. The RETC is a biennial event jointly sponsored by SME and the American Society of Civil Engineers (ASCE). Conference attendance was 573 members, nonmembers and students, an increase of seven attendees from the 1995 conference in San Francisco, CA. Exhibitors occupied 51 booths at the Las Vegas RETC. The 1997 conference encompassed 58 presentations in 15 sessions. Participants were given details on achievements and advances that have resulted in new design solutions, alternative work practices and increased productivity within the industry. The page at the end of this article tells how to get your copy of the RETC proceedings, either hardbound or on CD-ROM. Or, if you wish, for the first time a CD-ROM is available with the complete RETC proceedings from 1972 to 1997. This two-disk, archival volume has key-word search capability, is in portable file format and is compatible with PC and Macintosh platforms. RETC program sessions included design and planning, ground support, tunnel boring machine (TBM) case histories, conventional excavation, new technology, difficult ground, geotechnical, shafts and raises, future/special projects, new Austrian tunneling method, international projects, soft ground case histories and water and gas. What follows are highlights of some of the RETC presentations.

Jan 1, 1997

By G. A. Doyle

The quality of water in mine pit lakes depends in part on the physical limnology (Le. stratification, turnover, and development of anoxic conditions with depth) of the lake. Limnologic data collected from four existing pit lakes indicate that pit lakes develop a thermocline, or temperature stratification, in the upper 10m to 30 m of the water column. Two of the pit lakes (26 m and 55 m deep) undergo seasonal turnover of the entire water column, whereas two deeper pit lakes (110 m and 240 m) undergo seasonal turnover of only the upper portion of the water column. In the deeper lakes, seasonal mixing does not extend through the entire water column and a distinct chemocline develops with depth.

Jan 1, 1996

By Forrest T. Moyer

INJURY experience and employment data are presented in this chapter for metal and nonmetal mines, stone quarries, sand and gravel pits, iron blast-furnace slag plants, and metallurgical plants (including ore-dressing and nonferrous reduction plants and refineries) in the United States. Employment and injury experience data for all mineral industries are given in volume II. The 1962 figures are preliminary summations which are subject to revision. They were compiled from all reports from producers received by the Bureau of Mines through April 15, 1963. The data for metal, nonmetal (except well and brine operations), stone, and sand and gravel operations were collected by a mandatory reporting system under the provisions of the act of September 26, 1961, Public Law 87-300 (75 Stat. 649). The act authorized the Secretary of the Interior to study the various aspects of safety in metal and nonmetal mines (excluding coal mines) and report the findings 2 years sub-sequent to the enactment of the law. Data on nonmetal well and brine plants and nonferrous reduction plants and refineries were reported voluntarily by the operators. METAL MINES Preliminary data for the metal mining industry comprise reports on 1,871 mines and pits. The combined fatal and nonfatal injury-frequency rate was 31.95 per million manhours in 1962, a decrease of 8 percent from the similar rate of 34.54 in 1961. Metal operations reported a total of 61 fatal and 3,201 nonfatal injuries.

Jan 1, 1963

By Marcos Danilo Monteiro

O final do século XX foi marcado por um grande avanço tecnológico em sistemas automatizados com variadas aplicações, dando destaque ao campo da robótica que desde então busca otimizar cada vez mais os processos industriais, eliminado a mão-de-obra humana em segmentos onde sua presença antes era indispensável. O aumento na qualidade do produto, a relação custo-benefício e dentre outras melhorias que a robótica trouxe a uma linha de produção industrial, justificam a procura por parte das grandes empresas em procurar investir na inserção desta tecnologia ou no melhoramento dela em sua cadeia produtiva. Este trabalho teve como principal objetivo demonstrar a aplicação da tecnologia robótica na indústria, em proporções reduzidas e fins didáticos, com a integração de um sistema de controle e automação representado pela plataforma Arduino que atua no controle de coordenadas de um braço robótico em atividades de carregamento e paletização de cargas.

Jul 30, 2018

The early history of the mine is traced from the beginning of shaft sinking in 1886 to the purchase by the Broken Hill Proprietary Co. Ltd. in 1949. A necessary preliminary to mechanisation of the Borehole Seam was development of the Young Wallsend seam, andthis development is described. Surface reorganisation and coal handling arrangements are dealt with in detail. Then follows a description of the Borehole Seam mechanisation, the provision of power supply for this purpose, arid pumping arrangements in themine.INTRODUCTIONStockton Borehole Colliery is in the Parish of Teralba, between the townships of Teralba and Boolaroo, and about 12 miles from Newcastle. The colliery holding, a freehofd area of 2,560 acres, was apparently an original land grant when acquired by Teralba Co-operative Coal Company who decided to mine for coal and named the mine "Teralba Colliery." Shaft sinking was commenced in 1886 but was delayed by financial and water troubles to such an extent that it was not until 1901 that the Borehole Seam was reached.Coal was won until 1904 using a single 16 ft. diameter shaft, ventilation being achieved by means of a wooden boxing down one side of the shaft. This collapsed, and operations ceased until the mine was taken over in 1906 by a company known as "Borehole Colliery Limited," the principal stockholder being the Stockton Coal Company. It renamed the mine "Borehole Colliery." This new company immediately commenced sinking a 13 ft. diameter air shaft. In 1908 the Stocktol1 Colliery at Stockton was abandoned, and during the following year much of its equipment was transferred to Borehole Colliery. The name was again changed becoming "Stockton Borehole Colliery." From this period on, coal was produced from the Borehole Seam by...

Jan 1, 1957

By T. R. Raponi

"The Williams Mine, Canada's largest gold mine, processes over 6,000 t/d of ore utilizing SAG/ball milling, leaching and CIP, carbon stripping, electrowinning and refining to produce gold dare bullion.Grinding accounts for over 50% of milling costs with grinding media, power and mill liners making up over 75% of grinding costs. Since 1991, several changes in these areas have been made which have significantly reduced costs, while fineness of grind and mill recovery have both been increased.This paper discusses the changes made in the grinding circuit over the past few years and assesses their impact on operating costs and mill operations.IntroductionThe Williams Mine is located in the Hemlo area of northwestern Ontario, about 40 km east of Marathon. It is operated by the Williams Operation Corporation, which is equally owned by Teck Corp. and Homestake Canada Inc. Canada's largest gold mine, the Williams Mine commenced operation in October 1985 at a rate of 3, 000 t/d. Mill throughputs have typically exceeded design, averaging 3, 397 t/d in 1986, and 3,380 t/d in 1987. In August 1988, production was increased to 6,000 t/d. Throughput averaged 4,212 t/d in 1988. Production increased over the next few years averaging 5,477 t/d in 1989, 6,248 t/d in 1990, 5,987 t/d in 1991, and 6,283 t/d in 1992. With a recovery of over 95.5%, production for the first three quarters in 1993 is averaging 6,408 t/d.GeologyThe main ore body is a steeply dipping conformable zone of microcline-quartz-muscovite rock. It occupies the contact zone between hanging wall metasedimentary rocks and foot wall felsic quartz feldspar porpyritic rocks of possible volcanic or subvolcanic intrusive origin. The ore body is enveloped by muscovite schists which are thickest on the footwall side. The schist is enriched with tourmaline, pyrite, and green mica containing vanadium and barium. The ore body contains pyrite and barite which occurs mostly in laminae and bands to veinlets and breccia fillings. The gold occurs as free (native) grains, 20 to 30 µm in size at grain junctions of the microcline and quartz. Visible gold is rare in the main zone. There are commonly two or more discernable layers of economic value which are separated by weakly gold mineralized material which usually consists of muscovite schist, barite rich zones or sulphide poor-microcline-quartz rock and in the upper and western fringes by biotite rich schist with feldspathic fragmental characteristics. Molybdenite is a common constituent as very fine disseminated grains in the microcline-quartz rock and is most prominent with gold enrichment. Stibnite and realgar are two of the more common accessory sulphides."

Jan 1, 1994

By J. M. Stuart, G. D. Bengough, A. R. Lee

Corrosion tests should be designed so as to facilitate as far as possible the interpretation of results, consequently factors which may affect the rate of corrosion should be controlled as far as practicable, and very full data should be given regarding the conditions of the test. Among the most important factors affecting the rate of corrosion is often the rate of supply of oxygen to the metal surface. It is essential therefore to understand the mechanism by which oxygen is transferred from the liquid surface to the surface of the metal. The work of Adeney and his coworkers has thrown much light on this mechanism. They have shown1 that the aeration of deaerated water and salt solutions proceeds much more rapidly than can be accounted for by mere diffusion, and have suggested that downward "streaming" takes place from the surface of the water, due mainly to an increase of density brought about by evaporation. The evaporation reduces the temperature of the surface layer, and also increases the concentration in the case of salt solutions. The effect of evaporation in facilitating the transfer of oxygen to a metal and increasing the corrosion of the metal was shown in some experiments due to Friend.2 He tested the corrosion of mild steel plates immersed in water in glass jars, a steady stream of air being drawn over the surface of the water in the jars. The air passing through half the number of jars was saturated with moisture, that passing through the others was dried with calcium chloride. He found that "in every case the water exposed to dry air was approximately twice as corrosive as that exposed to air saturated with water vapor." Conditions for Quantitative Corrosion Tests These results show that we must either control or prevent evaporation at the liquid surface, if we wish to avoid effects on the rate of cor-

Jan 1, 1929

By A. R. Lee, G. D. Bengough, J. M. Stuart

Corrosion tests should be designed so as to facilitate as far as possible the interpretation of results, consequently factors which may affect the rate of corrosion should be controlled as far as practicable, and very full data should be given regarding the conditions of the test. Among the most important factors affecting the rate of corrosion is often the rate of supply of oxygen to the metal surface. It is essential therefore to understand the mechanism by which oxygen is transferred from the liquid surface to the surface of the metal. The work of Adeney and his coworkers has thrown much light on this mechanism. They have shown1 that the aeration of deaerated water and salt solutions proceeds much more rapidly than can be accounted for by mere diffusion, and have suggested that downward "streaming" takes place from the surface of the water, due mainly to an increase of density brought about by evaporation. The evaporation reduces the temperature of the surface layer, and also increases the concentration in the case of salt solutions. The effect of evaporation in facilitating the transfer of oxygen to a metal and increasing the corrosion of the metal was shown in some experiments due to Friend.2 He tested the corrosion of mild steel plates immersed in water in glass jars, a steady stream of air being drawn over the surface of the water in the jars. The air passing through half the number of jars was saturated with moisture, that passing through the others was dried with calcium chloride. He found that "in every case the water exposed to dry air was approximately twice as corrosive as that exposed to air saturated with water vapor." Conditions for Quantitative Corrosion Tests These results show that we must either control or prevent evaporation at the liquid surface, if we wish to avoid effects on the rate of cor-

Jan 1, 1929

By S. J. Prison, C. R. Smith

The effect of fluid injection to control water coning in oil and gas wells was investigated. Analytical and model techniques were employed. The factors investigated were the position and length of the completion interval, the point of fluid injection, the viscosity of the injected fluid and the relative thickness of the oil and water sections. The resulting influence of these factors on the net producing water-oil ratio was determined. Several important conclusions can be drawn from the study. In general, it was found that the net producing water-oil ratio can be reduced by fluid injection. The magnitude of this reduction depended on the factors listed above. An important practical consideration is that the injection fluid may be either oil or water. If the injected fluid is less dense than the connate water of the reservoir, the fluid will not be lost. This fact is reassuring when valuable oil is being injected. Efforts to suppress water production were more successful when the injection fluid was more viscous than the reservoir oil, or when a zone of reduced permeability existed in the vicinity of the point of fluid injection. Under test conditions, little benefit was derived through the use of impermeable barriers or cement "pancakes". INTRODUCTION The occurrence of water coning has been known for at least 60 years. In thin oil or gas pay sections, the presence of an oil-water or gas-water contact hinders production and often causes early abandonment of the afflicted well if a completion is even attempted. Even when relatively thick pay sections are found, the encroachment of water when a water drive is present will eventually pose serious water coning problems. This water is often corrosive, expensive to separate from the oil or gas and is costly to dispose of. The theory of water coning has been discussed by a number of authors. 1,2,3,4 Briefly, water coning to the producing interval in a well is due to pressure gradients resulting from the production of fluid from the reservoir. These pressure gradients will cause a water cone to rise toward the bottom of the producing interval if a water-oil or water-gas contact exists. The tendency of the water to cone is offset or partially offset by gravity forces since the water has a higher specific gravity than the oil. A balance then exists between two forces, gravitational forces arising from the difference in specific gravities of the oil and water, and the pressure gradients causing the flow of fluids to the wellbore. If the pressure gradient exceeds the gravitational force, water coning to the wellbore occurs and water production results. Through the years considerable thought has been given to the water coning problem. More than 50 U. S. Patents have been granted to inventors on the subject. A relatively complete literature review of the water coning problem has been made. 5 A number of these patents hold considerable promise for the solution or the partial solution of the water and/or the coning problem. Very little has been written describing field tests of techniques for the suppression of water coning. A notable exception is the paperby West. 6 He reports success in reducing gas coning by a combination of gravel packing and oil injection above the oil-producing interval. He also describes a comparable method to prevent water coning, but provides no field examples. This study experimentally and analytically verifies the benefits of oil injection as a means of partially or completely suppressing the water cone. While the gas coning problem was not treated, it is anticipated that results comparable to those obtained in water suppression could be obtained with reduced oil injection since the viscosity contrast between oil and gas exceeds that between oil and water. For the purpose of this study, the conventional potential flow theory was applied to the water-coning problem. The experimental verification centered on both a radial and a linear model. The model study permitted the investigation of complex flow configurations and the use of fluids of differing densities and viscosities. No analytic expressions are available to permit a solution of the problem as stated (see Fig. 1).

By Theodore von Rosenvinge

Large diameter (2.4 meter) drilled shaft foundations were installed to depths of over 62 meters through soil into Arkose bedrock for Connecticut?s Pearl Harbor Memorial Bridge (I-95 over New Haven Harbor). The project involved many ?firsts? including the first ?extradosed? cable-stayed bridge in the US, and for Connecticut, the deepest drilled shafts, the first use of a rotator to install shaft casing, and the first use of the Mini-Sid technology for rock socket bottom inspection. Design utilized both friction and end bearing for rock sockets. O-Cell testing was employed to maximize performance factors during design and to allow adjustments to socket lengths during construction. Favorable test results permitted a reduction in socket lengths and significant cost saving.

Jan 1, 2011

By D. Loy LeRoy

As we are all aware, the impacts of the 1977 Surface Mining Act and the implementing OSM Regulations require application of new, as well as existing, equipment and technologies. Our firm recently completed (June, 1979) a study for the Department of Energy titled "Analysis of the Impact of Public Law 95-87 on Mining Performance." The objective of the study was to analyze the impact of the Act and its regulations on mining performance in order to provide recommendations to alleviate the impacts identified, including identification of research needs. This paper presents some of the highlights of that report: projected cost increases; additional equipment needed for compliance; review of methods currently practiced or those which can be modified; and will focus particulary on equipment and technology applications.

Jan 1, 1980

By Magnus Troilius

The heat-calculations of gas-analyses involve cumbrous multiplications, which are apt to lead into errors. The foliowing tables and formulae have been found useful as facilitating such calculations, and therefore I hope that they will be of interest to some of the members. By "heat-unit" will, in the following, be understood the amount of heat required to raise the temperature of 1 kilogram of water l° Cent. All the tables refer to cubic meters at O0 and 760 mm. pressure. The following gas is chosen as an example: C02, - 4.0 vol. per cent. co, = 20.0 " CHI, - 3.5 " H, - 7.0 " N, - 65.5 " " 100.0

Jan 1, 1884

By I. Yarita

Magnesium alloys have the lowest density among the metals in practical use, and have properties such high specific strength, electromagnetic interference shielding and good vibration damping. Thus, there are many applications of these materials in automotive and electric parts. However, there is a little use of the products of metal forming of these materials because of poor plastic deformability in the normal temperature range and their high cost of production. To expand the range of application of products manufactured by metal forming, rolling technology for producing thin sheets having good mechanical and surface qualities is required. In this study, hot-rolled Mg-alloy sheets are experimentally rolled with or without lubrication in the temperature range from 293 K to 523 K. Rolling force, plastic deformability and surface quality are investigated, and the grain structures and their uniformity are observed. The effect of friction between the roll and the deforming material on the uniformity of the grain structure is discussed. Moreover, rolled materials are annealed and their mechanical properties are investigated by the tensile test and compared with those of as-rolled materials. The effects of the rolling conditions on the mechanical properties are discussed.

Jan 1, 2006

By Gregory Dybalski

The purpose of this paper is to illustrate the forecast capability of the econometric model of the cobalt industry1/ as utilized by the Federal Preparedness Agency. Forecasts from this model are illustrated from the premise that the leading producer continues production of cobalt. An alternate forecast is presented where the model structure is altered to reflect the condition where the leading producer leaves the market. All estimations and forecasts presented here are shown for illustrative purposes. The cobalt industry is highly concentrated; one company, owned by the Zaire government, accounts for approximately three-fifths of world production. The cobalt supply outside of Zaire is determined by the level of activity of copper or nickel markets, as cobalt is mined as a by-product of copper or nickel. The demand for cobalt reflects a diversified usage pattern; cobalt is used mainly in heat and corrosion-resistant materials, high- strength materials and permanent magnets. According to 1974 U.S. consumption data superalloys accounted for 22%, magnetic alloys 18%, cutting and wear-resistant materials 13%, and catalyst 7%. Foreign consumption is probably similar in terms of usage categories, but the relative order of the categories is in variance.2/ The Cobalt Model The cobalt model's object is to explain consumption, supply and price movements by utilizing statistically estimated equations. Central to the econometric model is the role of Zaire as the profit-maximizing "dominant firm". Zaire sets the price that is most profitable for itself. The price of cobalt depends on industrial demand, production of other firms, and net exogenous purchases, such as government

Jan 1, 1977

By Gerald Edmunds

CASTINGS of pure metals and many alloys usually have a coarse-grained structure characterized by long columnar grains throughout the main body of the casting. Frequently, the surface exhibits finer, some-times nearly equiaxed grains, and such grains may also compose other parts of the casting. This paper deals primarily with determinations of the grain-orientation textures of the columnar and surface grains of polycrystalline zinc castings. It includes some results upon a cadmium casting and a magnesium casting. A hypothesis is devel-oped to account for the observations on columnar grains and to use as a basis for predicting orientations in other cast metals. A general description of the position of the columnar grains in castings is that their long axes are approximately parallel to the direction of the thermal gradient during crystallization. Thus, in cylindrical castings the columnar grain axes tend to be radial, and in large flat castings where most of the cooling is through one or both of the large mold surfaces they tend to be perpendicular to the mold surfaces. At the edges and corners the direction of heat flow and there-fore the position of the grains is more com-plex. Actually observation shows that even in castings made in flat molds the cooling seems to be somewhat irregular, since columnar grains tend to emanate from certain areas of the cooling surface, indicat-ing that thermal contact was better there than in neighboring areas.

Jan 1, 1940

With a growing concern over mine fires, prevention and suppression are hot topics. NIOSH researchers Michael Trevits, Alex Smith and Edward Thimons discuss their research in the area. The leading causes of US mine fires include flame cutting and, welding operations, frictional heating and ignitions, electrical shorts, mobile equipment malfunctions and spontaneous combustion. From 1990 through 2007, there were 1601 reportable fires that occurred in the US mining industry -an average of 89 fires per year. The fact that mine fires are occurring with alarming regularity reinforces the importance of recognizing and eliminating the potential hazards. These statistics also show the need for improved control and suppression technology to ensure worker health and safety if a mine fire does occur.

Jan 1, 2008

By R. H. SWEETSERS

A Discussion of Mr. Hall's paper, read at the Washington Meeting, February, 1905. R. H. SWEETSER, Sault Ste. Marie, Ont. (communication to the Secretary*) :-The recent work of furnace No. 1 of The Algoma Steel Co., at Sault Ste. Marie, Ontario, using for fuel, first all charcoal, then a mixture of charcoal and coke, and finally all coke, upsets the estimates given by Mr. Hall in the last two paragraphs of his interesting paper. Furnace No. 1 was built for a charcoal-furnace, and it was run on charcoal fuel from March 6 until July 9, 1905; then, for a week, a mix¬ture of charcoal and coke was used, and, since then, coke alone has been the only fuel. It is to be regretted that at no time, during the run on charcoal, was there enough charcoal on hand and " in sight'" to warrant blowing the furnace as hard as it should have been blown. During April and May the supply of charcoal limited the amount of blast to about 8,000 cu. ft. of air per min.; in June, to about 8,900 cubic feet. For a few days in July about 10,000 cu. ft. were blown, and then the maximum daily output, 173 tons (2,240 1b.), was reached. At all times the quality of the charcoal was poor, having been made from wood cut from three to four years before. Doubtless this furnace could have produced .200 tons of iron per day, even with this quality of charcoal, provided the supply had been sufficient; and with good charcoal I see no reason why it could not make as much iron per day as it has made with coke. During the one week of using a mixture of charcoal and coke, the changes in quantity of blast and composition of the slag followed each other so closely that no single condition could last long on the furnace. The results were good, and the pig-iron was about the same in quality as that made during the

Jan 1, 1906