Search Documents

R. G. BROWN, Bodie, Cal.: Mr. Rickard's paper, with its valuable illustrations, brings into fresh clearness the game of hide-and-seek which the miner must play with his ore-deposit; but, more than this, it goes far towards classifying those perplexing idiosyncrasies which, while unclassified, constitute a labyrinth almost without clue. Probably every engineer can add to the list by the mention of at least one fresh detail from his own experience, and I for one would like to comment on two of Mr. Rickard's divisions. To what he has written about " walls within walls" and " walls without walls," the accompanying Figs. 1 and 2 may be appropriate, the more so as they represent conditions obtaining in a part of the Butte copper-belt more typical of the copper-veins as a whole than the Gagnon, which, in some respects the most interesting mine in the camp, stands almost alone in many particulars. (See nuns., xvi., 62.) Fig. 1 was sketched in January, 1895, in the stopes above the 700-foot level of the Colusa-Parrot mine, east of the Parrot and southwest. of the Anaconda. The stope, the commercial foot-wall of which is shown at A, was 30 feet wide at this section, the pay-ore being massive chalcocite, jumbled with bornite, pyrite, quartz and thoroughly broken-down granite. A and At are inch-thick seams of black talc; B, B' and B" are also talc, possibly 1/8-inch thick. In the plane of the section the "banded quartz " and " quartz and pyrite " were both of too low grade for extraction, but 5 feet back along the stope had been of fair value. The granite with quartz and bornite between Bt and A' was pay-ore, but that to the right of B" was not. In both cases the ferro-magnesian minerals had been removed, leaving, where not obscured by ore, faint, dark patches. Between A'

Jan 1, 1897

By Floyd C. Kelly

There is an ever-increasing demand for furnaces with controlled atmosphere, due to the large quantities of steel being used in the automotive industry, such as the high-chromium stainless irons, the 18 Cr, 8 Ni stainless iron and low-carbon steel sheets. The difficulties involved in the annealing of such materials, if they are to be kept absolutely free from oxidation, are many. It is possible to bright-anneal these steels in small laboratory hydrogen furnaces, using specially purified hydrogen and taking some additional precautions. In the first place, the insulation, usually of alumina or magnesia, holds small amounts of water vapor, which it is almost impossible to remove completely. Secondly, there is always condensataion of water vapor in the cooling chambers of such furnaces, and with the continuous circulation of the hydrogen gas in the furnace, the water vapor is carried from the cooling chamber back into the heating chamber. This water vapor oxidizes the charge. Lastly, the supply of moisture is made sure by the diffusion of small amounts of air from the atmosphere into the furnace against the pressure of the hydrogen. The oxygen combines with the hydrogen and forms more water. Under such conditions there is little gained by using specially purified gas, because it becomes contaminated after reaching the furnace. Low-carbon Steel If a sheet of low-carbon steel is annealed in such a furnace at 750" C. and allowed to cool with the furnace, an adequate flow of purified hydrogen being maintained all of the time, the steel will come out with a very thin coating of blue oxide. If a similar sheet is annealed at the same temperature and quickly pushed into the cooling chamber, it will come out nearly bright, or perhaps with only the edges slightly discolored. It is difficult to get a piece of steel through a furnace of this type with an absolutely bright surface. This is due to the fact that there are always traces of oxygen or water vapor in the furnace. When the steel is allowed to cool with the furnace, it reaches a critical temperature where the affinity of iron for oxygen is greater than that of hydrogen for oxygen, and the steel comes out discolored. If the steel is pushed from the hot zone

Jan 1, 1931

By John S. McCartney

This paper focuses on the seasonal thermo-mechanical response of two energy foundations installed at the new Denver Housing Authority Senior Living Facility in Denver, Colorado. The two drilled shaft foundations, which have diameters of 36 inches and depths of 45 ft and are end bearing in the Denver shale formation, include a closed-loop series of polyethylene tubes through which fluid is circulated to exchange heat with the surrounding ground. The tubes within the foundations are coupled together with the conventional ground source heat pump system for the building and were installed to evaluate the heat exchange response of the foundations as well as any thermo-mechanical soil-structure interaction effects. A series of vibrating wire strain gages and thermistors were installed at different depths in the foundation to record the thermo-mechanical strain and temperature at different depths. Also, pipe-plug thermocouples are used to measure the inlet and outlet temperature of the heat exchanger fluid entering each of the foundations, which is necessary to evaluate the total heat exchange for the foundations and the efficiency of the heat pump. This paper will describe the energy foundation construction processes, the strain distribution and ambient temperature profiles during building construction and the seasonal strain and temperature distributions during heating and cooling of the building. The data indicates that typical heat exchange associated with heating and cooling operations leads to strains which are within acceptable limits, and that the foundations can provide a clear option for absorbing the base heating and cooling load for the building.

By J. B. Newsom

SAFER, cheaper, and faster sinking of mine openings seems to have been realized with the completion of a borehole 5 ½ ft. in diameter and 1208 ft. deep, in Minnesota, during 1938. Moreover, as the opening is to be used solely for ventilation, its circular cross section, smooth walls and freedom from fire hazard recommend it in comparison with the usual timbered shafts of rectilinear cross section. It should be pointed out that a drill hole sunk without the use of explosives frequently will stand open without support, whereas a shaft sunk by standard procedure using dynamite usually must be timbered because of the wall-shattering effect of explosives. The saving in maintenance resulting from the elimination of timber is obvious. The work was done by Pickands Mather & Co. at its Zenith mine, Ely, Minn. This company wanted a ventilation opening capable of delivering 50,000 cu. ft. of air per minute to the fourteenth level, 1200 ft. below the surface. While several general articles1-3 have described the method used, detailed time and performance records have not been presented before. Moreover, with a method as new as this, it is important to compare the results attained under widely varying conditions. Among the new conditions faced at Ely were some extremely hard rock, a series of vertical fractures, seepage water, and some long stretches of sound rock which, combined with excellent equipment, gave a chance to operate without unusual delays. Developments in boring large holes have generally taken the obvious course of increasing the size of the equipment, a line of attack that has resulted in putting down 3-ft. diameter holes at damsites for studying the foundations4 and in drilling ventilation openings between levels at Butte. 5 Such drills operate from the collar of the hole, and the power from the drill is transmitted to the cutting tool through drill rods or pipes. In order to keep down the volume of rock that must be ground to sludge, the cores in large-diameter drilling are made as large in diameter as possible. Their large diameter increases their weight per foot of length, which

Jan 1, 1939

By Russell Webster

In having maintained production for more than 40 years Arizona's Magma mine is unique in a mineral district that includes several major copper mines. Other past and present producers in this area are Miami and Inspiration at Miami, the Old Dominion in Globe, the Ray mine in Ray, and to the south the new San Manuel mine near Tucson. Magma's production of copper, silver, gold, and some zinc has come from nearly parallel east-west striking mineralized faults, one called the Main or Magma vein and the other the Koerner vein, about 1100 ft to the south. This vein system has been prospected and partially mined for some 9000 ft horizontally and 4800 ft vertically. In ascending order from the deepest exploration level, the Main vein cuts Pre-Cambrian schist, Pre-Cambrian Apache Group, Post-Devonian diabase, and Devonian, Mississippian, and Pennsylvania limestones. Until 1950 very little ore was obtained from replacement mineralization.

Jan 10, 1958

By J Elder

Magnetic separation equipment has long been used to upgrade and beneficiate a wide variety of minerals and materials. Over the years, significant advances in both wet and dry magnetic separators have improved their operability and separation performances, broadening their use.But no one answer exists to the question: what is the right type of magnetic separator? For many minerals, including ilmenite, both process routes may be viable. There are technical, production, as well as economic reasons for choosing wet versus dry. However, recent developments illustrate that a new generation of wet magnetic separators is approaching performance once seen only in dry magnetic separation. With quality and production performance becoming similar, the choice between wet and dry magnetic separation is not as cut and dry as it once was.

Oct 5, 2011

By T. M. Barczak

Pumpable roof supports provide an alternative approach to secondary support in underground mining. Unlike all other supports that are either partially or fully prefabricated prior to being transported into the mine, the pumpable support is fabricated in place in the mine entry. This reduces the underground material handling efforts and thus the injuries historically associated with in-mine support construction. On-site fabrication also facilitates application of the support in areas that are inaccessible to transportation equipment such as scoops or rail cars, making it ideal for many bleeder applications. One of the main advantages of the pumpable support is that it fully bridges from the mine floor to the roof, thereby eliminating the requirement of ?topping off? the support with wooden wedges or crib blocks that soften most other support responses. This report examines the development of modern pumpable roof support technology and provides a full description of the performance capabilities of each of the support products now on the market.

Jan 1, 2008

By D. D. Porter, C. Fairhurst

Crack propagation in the region of a statically pressurized borehole is investigated to determine a role of the sustained borehole pressure following detonation in a blast. The case of a single-hole bench blast is reduced to a plate model, which is considered both theoretically and experimentally. Based on the principle of least work, it is hypothesized that the path of any crack in the plate will coincide with one of a family of maximum principal stress trajectories. These trajectories were computed, and critical experiments in glass, designed to test the effects of controlled crack origin and of changed trajectories from different loading configurations, confirm this hypothesis. It is concluded that under ideal conditions the crack path can be predicted and that cracks can be produced in the absence of either high-amplitude stresses or stress waves. Energy considerations for crack extension are discussed, and, based on the strain energy distribution, a relationship between hole burdens and spacings is revealed, a critical burden is demonstrated, and a maximum crater width is shown to exist.

Jan 1, 1971

By Saulo Brinco Diniz

O presente trabalho buscou explorar a influência de um tratamento térmico de ressolubilização (70 minutos / 510ºC), antes da laminação convencional de uma liga de alumínio 7475-T7351. Para tal, duas amostras (com e sem o tratamento térmico) foram laminadas de 12,5 mm até 3 mm de espessura, após 13 passes com uma redução aproximada de 10% por passe. Com base nos resultados obtidos via microscopia óptica (Olympus, modelo GX51) e dureza Vickers (durômetro EMCOTEST, modelo Duravision 300), conclui-se que o tratamento térmico de ressolubilização adotado antes da laminação convencional da liga em estudo, propiciou modificações microestruturais e incremento na dureza quando comparada a amostra laminada sem prévio tratamento térmico de ressolubilização.

Aug 17, 2017

By R. W. Smith

It is well known that certain silicates such as the feldspars and beryl can be readily floated from quartz at a low pH value using a long chain cationic collector in the presence of a fluoride.1-3 However, the mechanism whereby the fluoride activates feldspars and beryl is not known. Indeed, only a few authors have even speculated about possible mechanisms.1,3,4 As a first approach to the problem, it is perhaps best to look closely at the interesting character of hydrofluoric acid and how it dissolves silica and silicic acid. Hydrofluoric acid, unlike hydrochloric acid, is a weak acid with a dissociation constant of about 3.53 x 10-4 at 25°C.5 The reason for the weak acidic character of HF lies in the very small size of the fluoride ion.6 The pKa value is 3.45 which means that at pH 3.45 half the HF is present in molecular form and half in ionic form. The anion present is probably HF2.-6 At pH values below the pKa value, molecular concentration increases rapidly at the expense of the HF2- anion. It is known that HF readily attacks glass, silicates, quartz and silicic acid. The equation usually cited pertaining to the first step in HF attack of silica is6-'

Jan 1, 1965

By K. L. Williamson, P. W. Dugan

INTRODUCTION In recent years there has been increased social awareness and government attention directed toward the mining industry. The growing influence of the Occupational Safety and Health Administration (OSHA), the Mine Safety and Health Administration (MSHA), and the Environmental Protection Agency (EPA) has resulted in volumes of regulations governing a multitude of health and safety aspects of mining and milling. These regulations naturally have had an impact on new plant design and in some cases have necessitated retrofitting of existing plants. This paper will not examine the regulations governing the industry, since they are a matter of public record, but rather will address two specific health considerations, dust and noise, and their influence on the design of crushing and screening plants. DUST AND NOISE CONCEPTS Dust is generally defined as finely divided solids which may become airborne without any physical or chemical change except fracture. Since the purpose of comminution circuits is to reduce the size of solids by fracture, a percentage of the material is normally reduced in size to a point where it can easily become airborne. The major cause of dust becoming airborne is the air induced by falling material. When granular material falls through a distance, the induced (or entrapped) air rushes out available openings, carrying with it the fine particles that have become suspended. For this reason, the major points of dust generation are the points where the material is falling: chutes, transfer points, screens and equipment feed and discharge points. The expected dust concentration in an area is a function of the degree of size reduction (i.e., finer particles are more readily carried by air currents than heavier particles) and the volume of air that is induced. The measured dust concentration values for various operations agree with this

Jan 1, 1982

By Thomas P. Meloy

Floating "fines" differs from floating "sands" because the fines have a much larger surface area compared to their mass. The forces that arise from this large specific surface the key to understanding the behavior and treatment of fine particles. Though the nature of these forces is not thoroughly understood, enough work has been done to give a qualitative picture of what is happening in a flotation cell. It is the purpose of this chapter to re-examine some of the more, recent theoretical work and-to indicate its importance.

Jan 1, 1962

By Willard L. Hunter

The research described in this Bureau of Minus report was conducted to improve the chromium-iron ratio of offgrade chromite. Two methods were used: (1) Iron was selectively reduced from chromite by carbothermic reduction in an electric-arc furnace, and (2) a mixture of carbon, chromite, and sometimes fluorspar was chlorinated to remove a substantial part of the iron. Chromite concentrate from the Mouat deposit in Montana and from northern California was used in the test work. Chromium-bearing slag and chromite that had been beneficiated by a roast-leach process were each smelted to produce high-carbon ferrochromium. Iron was selectively reduced in a laboratory-scale., electric-arc furnace. Carbon additions to the smelting charges varied from 40 to 100 percent of the stoichiometric requirement, and slag basicities were varied from 0.4 to 1.0 chromium-iron ratios of more than 4:1 were obtained with 89 percent recovery of chromium in a chromium-bearing slag.

Jan 1, 1962

By C E. Vidal

Geological exploration and mining development increased their intensity and rate of success during the last five years in Peru. Particularly relevant are the mining projects of Yanacocha and Pierina for epithermal Au and Ag. Also relevant are the new mining operations at Iscaycruz and Uchucchacua for limestone replacement Zn- or Ag-rich base metal skarn deposits. Miocene continental volcanics host the low-grade but near-surface orebodies of the Yanacocha mining district in Cajamarca. Several deposits have been mined since 1994 with open-pit and heap-leach gold production increasing from 300 000 ounces to 1 300 000 ounces in 1998. In a similar geological setting, but with three times the grade of Yanacocha, the Pierina valley-leach operation in Ancash is set to produce 800 000 ounces Au during 1999. At Iscaycruz in Lima, Cretaceous limestones host massive pyrite and sphalerite skarn deposits with 10 to 20 per cent Zn. Mining and milling were started in 1996 with last yearÆs production rising to 180 000 tonnes of Zn concentrates. At Uchucchacua, selective underground mining of fracture-controlled Ag skarns, with 400 to 420 g/t, has been recently increased from 1200 to 2000 tonnes per day to produce 5.5 million ounces Ag during 1998. Advanced exploration projects are located in the framework of nine Phanerozoic metallogenic provinces. Mineral deposits of preferred attention are precious metal disseminations and veins, base metal replacements and skarns, porphyry Cu (Mo-Au), Mississippi-Valley-type Zn and base metal volcanogenic massive sulphide deposits. Geological discovery of new orebodies enables a sustainable development of the mining industry in the country.

Jan 1, 1999

By M. Tiedtke, T. Crary, P. MacPhail, M. Ounpuu

"The SGS carbon-in-pulp (CIP) / carbon-in-leach (CIL) model was used to evaluate and optimize the carbon circuit at Alamos Gold’s Young-Davidson Mine. Plants samples (pulp and carbon) were tested in a series of small scale batch experiments to determine rates of gold leaching and adsorption on carbon from a combined flotation concentrate/tailing product. The testwork data, along with existing plant data were then used to model the performance of the existing CIL plant and optimize the circuit to improve performance and overall recovery. The primary purpose of the modelling exercise was to determine the most cost effective way to lower solution losses at the plant. The modelling was also used to learn how the various parameters in the CIL circuit affect solution losses and the gold inventory tied up on the carbon. This resulted in recommendations for minor changes in the CIL flowsheet, which were successfully implemented in the plant. The approach, results and plant changes are presented.INTRODUCTION This paper presents the details from testwork conducted on samples from Alamos Gold’s Young- Davidson gold mine which is located near the town of Matachewan, approximately 60 km west of Kirkland Lake in Northern Ontario, within the southwestern part of the Abitibi Greenstone Belt. The objective of the test program (completed by SGS Canada in 2013) was to investigate and model the combined flotation concentrate / tailing carbon-in-leach (CIL) circuit and suggest ways to improve gold recovery. The metallurgical test program included mineralogy, rheology, and carbon modelling testwork. Plant information was provided during the test program and used in the optimization process. Upon completion of the testwork, plant changes were recommended and implemented at site (October 2014). Plant results from 2014 to 2017 confirmed the modelling results."

Jan 1, 2018

By Jochen Franke, Derek D. Lichti

"This paper gives a brief introduction and presents recent enhancements in the MillMapper technology developed for thickness gauging and condition monitoring of liners in grinding mills used for mineral comminution. It also introduces the recent expansion of MillMapper functionality aimed at mill operational optimization. MillMapper uses calibrated laser scanner data captured inside a mill to determine thickness at several million points on all liner surfaces at feed, shell, and discharge ends with millimeter accuracy. Data capture takes nominally 5 minutes, hence interruption to mill operation is negligible.The paper is structured as follows. First, a review of the technology and discussion of recentlyimplemented innovations such as liner change out forecasting, automatic ball charge volume and weight measurement, and automatic mill liner volume/weight measurement for mill operational control or load cell calibration are presented. Combined weight information provides control over load related issues such as load fill levels for relining, or start-up load after reline. Feature descriptions are followed by a listing of the numerous advantages over existing techniques and the benefits to operations. Results from the application of MillMapper are presented throughout.INTRODUCTIONThe need for thickness gauging of liners of grinding mills used for mineral comminution is well known but the task is rarely completed to a satisfactory standard. Liner failure resulting from excessive wear can have expensive consequences. Furthermore, mill performance as well as liner wear are known to be correlated to lifter bar geometry (Napier-Munn et al., 1999; Rajamanni et al., 2005). At present, the following techniques are routinely used to gauge the thickness of mill liners:1. Visual inspection;2. Ultrasonic thickness gauging (for steel liners); and3. Physical inspection (e.g. nail inserted in rubber liners)"

Jan 1, 2008

By Barro L

Very large reserves of gas are contained in coal. Because of the low permeability of the coal gas flow rates are very low. Fracturing of the coal can be achieved by use of the nitrogen - foam frac techniques described but the flow rates after fracturing are not sufficient to support economic development. Fracturing of the seams in the Bowen Basin was as predicted but in the Sydney Basin no trace of the fracture could be found when development proceeded past the fractured well. Testing of coal samples has provided some insight into parameters affecting desorption Rates.

Jan 1, 1982

By Trudinger J. P

Concern for the environment by the public and by mining companies, has led to many recent attempts to revegetate areas disturbed by mining activities. The problem of successfully revegetating disturbed areas and mine wastes is often difficult, even under favourable conditions. Under the severe conditions that prevail in and and semi-arid parts of Australia, such difficulties may be extreme. An approach is described in which field trials are used to investigate factors which adversely affect revegetation and to evaluate optimum methods and treatments..A wide range of methods suitable for use in and situations is described. These include grading and cultivating operations, topdressing with natural soil materials, selection of suitable plant species, mulching and the use of fertilisers and supplementary irrigation. It is concluded that such a programme provides the best approach to this complex and expensive problem.

Jan 1, 1976

"The Schist Lake mine, owned and operated by the Hudson Bay Mining and Smelting Co., Limited, is situated on the northwest arm of Schist Lake, 4 miles southeast of Flin Flon, Manitoba.The deposit was discovered early in 1947, during a diamond drilling program exploring small copper showings along the west shore of the lake. The orebodies came to surface between the mainland and the north end of Stitt Island.Production began in August, 1954, at an initial rate of 300 tons per day. Underground workings have been carried to the 1,700-foot level, where exploration work is now being done.General GeologyRocks of the area are Precambrian lava flows, with associated pyroclastic breccias and tuffs, and related minor intrusions. Their general strike is northwest and their dip is nearly vertical. Shearing is common and is related to the activity which caused intense folding and much faulting in the area. The larger faults and the fold axes trend a few degrees west of north. The lavas are mainly andesitic but a layer of sericite-carbonate schist, which is probably derived from a fine-grained, grey quartz porphyry, occupies most of Stitt Island and extends into the mine area. It is within this layer of schist that the ore deposit occurs (Figure 1).The OrebodiesThe ore occurs as tabular to lens-shaped bodies which strike northwest, dip nearly vertically, and plunge at 60 degrees to the southeast. The ore zone is 800 feet long and has been traced for a distance of 2,000 feet along the plunge (Figure 2). The maximum length of continuous ore within this zone is 200 feet. Widths of individual ore lenses vary from a maximum of 35 feet to a minimum of 2 feet.The ore consists of three distinct types: massive sphalerite-pyrite, massive chalcopyrite-sphalerite, and disseminated chalcopyrite-pyrite. The No. 1, or eastern, orebody is predominantly massive sphalerite-pyrite. The western part of the No. 2 orebody is massive chalcopyrite-sphalerite. The disseminated ore forms the eastern part and the lower end of the No. 2 orebody. All three types of ore, with patchy distribution, are found in the smaller lenses below the 1, 100-foot level.Metallic minerals, in order of deposition, are pyrite, arsenopyrite, chalcopyrite and sphalerite, galena, enargite, and gold. Both massive types of ore exhibit banding in many places, probably as a result of the selective replacement of schist. The disseminated ore was formed as a filling of the interstices in a brittle chert rock which appears to have been crushed by the same forces which produced the schist."

Jan 1, 1949

By M. E. Nicholson

The solubility of carbon in Ni-Cu alloys was determined at 1000°C. The factors which limit solid solubility are discussed with particular reference to the influence of electronic factors. The results indicate the extent of solid solubility is a function of the density of states at the Fermi surface. THE solid solubility of an interstitial element is primarily limited according to Seybolt and Fullman1 and Speiser and Spretnak2 by (a) the strain energy produced when the solute atom takes its interstitial position, and (b) the partial molal free energies of the solid solution and the coexisting phases. In several binary systems of a transition and a noble metal, where there are no abrupt changes in strain energy or free energies of coexisting phases, the solid solubility of an interstitial third element drops abruptly to a negligible value at a composition corresponding to a complete filling of the "d-band." Such a decrease occurs in the case of hydrogen in the Pd-Ag system at 60 pct Ag.3,4 The solubility of carbon in Ni-Cu alloys seems to vary in a similar manner as indicated by the embrittling effect of carbon on these alloys. These al- loys are embrittled by slow cooling due to the precipitation of graphite. This embrittlement can be removed by heat treatment if the carbon content is less than the solid solubility limit at the heat-treating temperature. If the carbon content of the alloy exceeds the solid solubility at the heat-treating given temperxture, the embrittlement cannot be eliminated by solution heat treatment.' Since pure nickel has a carbon solubility of 0.25 wt pct6 at 1000°C, embrittlement is easily removed from commercial nickel and nickel-rich alloys, which may contain of the order of 0.10 wt pct C. Embrittlement due to carbon cannot be removed from Ni-Cu alloys containing 70 to 80 wt pct Cu by annealing unless: the carbon content is of the order of 0.04 wt pct CL or less."' Thus, it appears that the

Jan 1, 1962