Search Documents

By E. Owens, R. Gudavalli, D. Wilder, T. Xia

As mechanical shock and vibration environments evolve, it is important to understand their potential effect on human operators. Human beings are sophisticated mechanisms comprised not only of passive components with mass, damping, and stiffness characteristics, but also of components that can actively affect apparent mass, stiffness, and damping. Because the lumbar spine can exhibit local, short-column buckling, stability of the human trunk depends on the responsiveness of the neuromuscular control system.1-2 We have been evaluating the ability of patients with back pain to respond to a series of sudden loads. We believe the results have implications for isolation design and standards development. Methods 153 patients, aged 21 to 55, presenting with back pain agreed to enroll in a research study that randomly assigned them to one of three treatment arms: high velocity low amplitude spinal manipulation, low velocity variable amplitude spinal manipulation, or wait for 2 weeks and then be randomized to one of the above groups. Response to sudden load testing was one of a battery of baseline evaluations performed upon entry into the study and prior to treatment. EMG electrodes were attached to the skin over the paraspinal muscles of the standing participant bilaterally 3 cm from midline at the L3 level. While standing upright on a force plate (Bertec), participants were fitted with a strap around their back and hooked to a load cell in front of their chest. An accelerometer was rigidly attached to the load cell. Impact was applied to the chest using a cord attached to a falling weight. The weight’s fall distance was varied between 9 and 13 inches to account for the size of the subject. The subject was blindfolded and wore headphones playing white noise to prevent cueing of when the weight was dropped to apply the load. Hence, although the participant knew a load was about to be applied, he or she did not know the instant it would occur. Just before the weight was dropped, a 4 second data collection process was started for the two EMG electrodes, load cell, accelerometer, and force plate. The load drop was repeated 6 times, at irregular intervals, over a period of 2 minutes. The raw data thus collected was reduced to obtain several values: 1) length of time from the pull on the harness to the beginning of the response of the left and right paraspinal muscles (LES, RES), 2) time and magnitude of the maximum response, 3) force and acceleration experienced at the chest, and 4) the time and magnitude of the center of pressure location (COP). A general linear model was used to evaluate the results. Results For the EMG data, of the 1,824 observations made, 90% of them indicated a response. Prior to the sudden load, resting muscle activity was different between left and right sides (p=0.0001) and between males and females (p=0.0001). Female subjects began to respond to the sudden load within 92 to 110 ms and males from 101 to 109 ms. Females exhibited more variation in starting

Jan 6, 2006

By Marvin V. Damm, Lloyd C. Venburg, Dan Sokol

Analytical and computer models are used to evaluate information obtained from existing data and investigation programs so mine water control systems can be designed and developed. These models allow the geohydrologist to predict the amount of groundwater inflow and the impact of dewatering and stream diversion on the hydrologic regime, and to determine the schedule and equipment needed for mine dewatering. This article describes uses of the model and the essential components necessary to construct an effective and practical one. Hydrologic models are constructed to determine the extent that mining activities will affect the ground water and surface water hydrologic regime. These models range from basic analytical, mathematical models to the more sophisticated finite difference and finite element groundwater models. Many factors determine the degree of sophistication, including the mining stage, the complexity of the hydrologic regime, the mining process, and regulatory requirements. Model Uses The geohydrologist and engineer construct models so the entire ground and surface water handling and supply system can be integrated and optimized. These models can provide the following data: • Information for water balance studies-the entire hydrologic regime for the area, including precipitation, transpiration, evaporation, infiltration, runoff, and the effect of geologic features. • Data on seepage rates during mining. • Information to design the depressurization and dewatering system, including water well spacing, location of sumping systems, need for grout curtains, and possible horizontal drain and underdrain locations. • Data needed to schedule dewatering and mining operations. • Prediction of initial and long-term impacts of mining and dewatering, including local and areal drawdowns, effects on existing wells, and modifications to the surface-subsurface hydrologic regime. Potentiometric surface maps and hydrographs can be prepared from these data. • Prediction of the effect of discharge from the water control system on the surface hydrology and data input to design systems for water discharge, storage, recharge, or reinjection. The results of a computer study that illustrates the effect of dewatering and reinjection into an aquifer to confine the cone of depression are shown on the accompanying figure. • Information to forecast potentiometric surface recovery after mining ceases. The accompanying figure shows the pumping and reinjection rates in a program that is adequate to dewater a mine and permit the recovery of potentiometric levels to approximate premining levels after mining ceases. • Documentation and design information for monitoring systems to be installed during all mining phases. • Water quality predictions and geochemical changes, including the possibility of brackish or saline water intrusion because of extensive dewatering or depressurization operations. • Documentation and data for acquiring permits from regulatory agencies. Model Input Program For any model to be effective, detailed hydrologic and geologic data must be gathered from a review of existing information and from an investigative program. These data should cover entire model limits. Data updating, revising, and refining should occur as new information is received from the investigation and monitoring programs, and from the mining operation as it progresses through the pre-mining, mining, post-mining, and reclamation

Jan 8, 1982

By M. D. Lackey

The "Art" of Big Hole Drilling has been in a continual state of evolution at the Nevada Test Site since the start of underground testing in 1961. Emplacement holes for nuclear devices are still being drilled by the rotary drilling process, but almost all the hardware and systems have undergone many changes during the intervening years. The current design of bits, cutters, and other big hole drilling hardware results from contributions of manufacturers and Test Site personnel. The dual string, air lift, reverse circulation system was developed at the Test Site. Necessity was really the Mother of this invention, but this circulation system is worthy of consideration under almost any condition. Drill rigs for Big Hole drilling are usually adaptations of large Oil Well drill rigs with minor modifications required to handle the big bits and drilling assemblies. Steel remains the favorite shaft lining material, but a lot of thought is being given to concrete linings, especially precast concrete.

Jan 1, 1983

Estimating Breakage of Fine Ore Particles by Media in a Small Ball Mill Using DEM

Sep 13, 2010

By Arthur Taggart

THIS paper describes the result of a series of experiments run in the laboratory of the School of Mines, Columbia University, during the winter of 1927-28. It shows that the several operating adjustments of a pneumatic table produce effects in the action of a, given coal that may be grouped into two classes, viz.: stroke length, speed and rocker-arm angle, which affect longitudinal travel; air supply and table slope (transverse and longitudinal), which determine transverse travel. The magnitude of the effect of the different adjustments varies. Some of the adjustments affect stratification of the bed, both as respects size and specific gravity of the bed components, as well as direction of travel. Operation of a pneumatic table is fundamentally different from that of a wet table in that the former exerts, through the air supplied, a force on the particles upward away from the deck which is lacking on the wet table while, on the other hand, it lacks the positive control over cross travel that is supplied by the wash and feed water.

Jan 1, 1929

By Aaron Nickoli, Brad Clark, Thomas Horan E. I. T.

The Canal Road Dip Slide is an active landslide located on South Pender Island, British Columbia. The effects of the fall 2021 atmospheric river prompted the British Columbia Ministry of Transportation and Infrastructure to initiate an emergency response project to realign Canal Road out of the active landslide zone for safe traffic passage. The work was tendered in a bidding process and included blasting and rock excavation work at the project site. Tetra Tech Canada Inc. was retained by the contractor to be their Blast and Vibration Specialist. The close proximities of an active landslide, a Canadian National Park, and other segments of construction posed stringent constraints to blasting. The governing constraints to blast design included a Peak Particle Velocity (PPV) limit of 3 mm/s (0.12 in/s) along the adjacent landslide centerline and a slide movement constraint. Sixteen blasts were executed throughout the scope of work to remove 2595 m3 (3394 yd3) of meta-sedimentary rock. Blast designs adhered to the constraints by utilizing up to quadruple decking in 50+ blast holes which lead to complex timing schemes. Several blasts were over 4 seconds in duration, with one at nearly 8 seconds. The landslide area was monitored with Shape Accel Arrays (SAA) throughout the scope of work that tracked geohazard slide movement during construction. The SAA data is presented, and the effect of blasting is discussed. Site specific parameters for PPV estimation were calculated and are presented. Collaboration and communication between the stakeholders allowed the project team to successfully overcome the technical challenges posed by the Canal Road Dip Slide.

Jan 26, 2026

By Bratt G. C

When zinc is electrowon from concentrates or residues of high manganese content, the zinc sulphate electrolyte may contain high levels of manganese. The manganese level is usually controlled by removal of manganese at the anode as the dioxide during the zinc electrodeposition stage.By increasing the temperature of an electrolyte containing 8 gll manganese from 35°C to 90°C, decreasing the acidity from 100 gll to 30 gll, reducing the current density from 432.A.m-2 t6 286 A.m-2 and using new lead anodes containing over 0·75 per cent silver, the current efficiency for manganese dioxide removal was .increased from less than 1 per cent to over 20 per cent.At the same time the current efficiency for zinc deposition was maintained above 90 per cent by additions of high molecular weight cationic polyacrylamides to the cell. By utilization of these conditions in a small number of cells, the manganese level in the circuit could be economically concrolled to any desired level.With these conditions the formation of the dioxide changes from an indirect route, via Mn04-, to a direct oxidation of Mn2+ to Mn02.The incorporation of impurities such as Pb, K, NH4, Cu, Ni, or Fe makes the deposit unsatisfactory for direct use in Zn - Mn02 dry cells. The deposit structure changes from cryptomelane at low temperature to y3-Mn02 at high temperature.

Jan 1, 1975

By A. G. Storey, J. B. W. Bailey

"The Noranda Process at the Horne Division ofNoranda Mines Limited now smelts approximately 350,000 short dry tons of concentrate a year, which is 40% of the total smelter throughput. Campaigns are averaging 200 days and refractory consumption is much lower than in the conventional smelter.In this paper, details ofrecent operation are given, together with updated projections for operation with higher levels of oxygen enrichment.IntroductionThe Noranda continuous smelting process has been in operation at Noranda, Quebec, for six years and in that time it has smelted a million and a half tons of concentrate. It is currently smelting 1,200 to 1,250 tons per day of concentrate on an instantaneous basis"" and it is handling approximately 40% of the Horne smelter throughput.This paper will describe the current operation of the process and the improvements that have been made since 1976, when the process was described by L.A. Mills et al.lSince early in 1975, a high-grade matte averaging 73% copper has been produced, which is then sent to the converter aisle for final treatment. All the information in this paper refers to the operation of the process in the matte mode .Early in 1978, Kennecott Copper Corporation started up their new smelter near Salt Lake City, Utah , which has three Noranda Process reactors operating with high oxygen enrichment of the tuyere air (2). These furnace s incorporate some design improvements, which will be described briefly."

Jan 1, 1980

By AIME AIME

AMONG the industrial motion pic¬tures released in the last year of possible interest to people in the mining industry are the following: "A New World Through Chemistry," made by the public relations department of E. I. du Pont de Nemours & Co., Wilmington, Del. This film, which is in sound and color, interprets in twenty minutes of narration and ingenious photography many of chemistry's newest developments. It may be borrowed either in 16-mm. size on an 800-ft. reel, or 35-mm. size on a 2000¬ft. reel, the only charge being the cost of returning the film. Douglas D. Rothacker, 729 Seventh Ave., New York City, is prepared to loan free of charge except for transportation each way several films prepared in the plants of the International Nickel Co., 16 mm. with sound. These include: "Nickel High Lights," 35 minutes; "Nickel Mining," 18 minutes; "Nickel Smelting," 18 minutes; "Nickel Refining," 9 minutes; and "Copper Refining," 6 minutes.

Jan 1, 1941

By Funsho K. Ojebuoboh

With several “green” applications on the horizon, bismuth has become an even more important minor metal in the smelting and refining of lead. Smelters with a complex sulphide feed invariably deal with bismuth. Its behavior during the smelting of lead in conventional sinter-blast furnace operation is discussed. Because it readily deports to the lead phase during the refining of lead, its separation from refined lead remained unsatisfactory in early lead production. When commercial requirements of bismuth in lead became more stringent early this century, the procedure where by calcium and magnesium is used todebismuthise lead was developed. The present conduct of this 1936 process, the Kroll-Betterton process, is discussed with emphasis on operational improvements.

Jan 1, 1996

By Oleg N. Tikhonov

A new extraction method which includes a combination of gravity and alternating electromagnetic fields with interfriction of mineral particles was proposed (Tikhonov O.N., 1979) and tested in lab conditions at Mineral Processing Department of St. Petersburg Mining Institute. At the beginning of the work the main goal was to find an efficient alternative to traditional extraction methods (like shaking table, etc.) used for concentration of fine alluvial gold particles. After the method and a series of gradually improved lab separators (Tikhonov, et al., 1983) were positively tested for gold (Tikhonov, et al.. 1986) the efficiency of the method was also proved for extraction of and other heavy minerals from alluvial and ground ores in experimental work at the St. Petersburg Mining Institute. The fine heavy minerals were separated to concentrates with high technological indices (Andreev et al., 1987), (Tikhonov, Gladkov, 1987), (Tikhonov, Gladkov 1989). In parallel a semi-industrial gravi-electro- magnetic separator was made and several technological flowsheets were designed for testing the method in industrial conditions (Tikhonov O.N., Miazin B.N., 1987), (Tikhonov O.N., Tolstunov S.A., Jebelev V.V.,1989). A series of industrial tests accompanied with complete sampling and standard technological measurements were performed at several alluvial deposits, with good technological indices. Thus the method and the flowsheets displayed high additional recovery of fine alluvial gold particles during elkrated industrial experiments in Siberia (Aldan province). At higher concentrate grade this method, even in one-stage operation, increased gold recovery more than by 25% compared with shaking table (for particles -0.10 mm gold recovery was 82% vs. 55% by shaking table, for particles - 0.25mm the recovery was 97.5% vs. 61.8%). Experiments were performed by joint team of St. Petersburg Mining Institute and the Irkutsk Institute of Rare Metals (Tikhonov O.N., Gladkov S.A., Tarasova T.B., 1991).

Jan 1, 1995

By Rudolf Keller

"EMEC Consultants is developing a process to extract oxygen, aluminum and silicon from lunar anorthositic soil. The process will provide oxygen in space for propulsion, aluminum as a structural material, and possibly silicon for the construction of solar cells.The evolution of the process concept in the course of our present NASA-sponsored SBIR effort is discussed. A molten salt electrolysis producing aluminum and oxygen is the central step; inert anode technology is to be employed. Silicon will be produced by reducing the anorthite, CaAI2Si20S' with aluminum. In a steady-state operation, all components of the ore added have to be removed from the process, and the removal of calcium is a major topic of our experimental studies.Utilization of Lunar ResourcesUtilization of lunar resources may play an essential role in the exploration of the solar system and the conquest of space. High costs are involved in overcoming Earth's gravity to supply missions in space. Even at a low projected cost of $ 300 for transporting a pound of payload into Earth orbit -- today's costs are many times higher -- it appears attractive to use resources in space to produce needed materials. Processing of lunar resources on the lunar surface is an obvious possibility.Oxygen is a product of major interest. It is required for support of human life in space. Even greater quantities may be needed for propulsion, to conduct further missions into space. To satisfy this demand for oxygen through lunar processing requires a quite different solution than to supply oxygen on Earth, where oxygen gas is abundant and easy to extract from air or water. On the lunar surface, solid oxide materials have to be used. Hydrogen reduction of ilmenite and subsequent electrolysis of the resulting water is being studied [1]. Other suggestions include fluorination of lunar soil [2], reduction with lithium and electrolytic decomposition of the resulting lithium oxide [3], and aqueous HF leaching [4]."

Jan 1, 1988

Legislation for control of ventilation in New South Wales coal mines is contained in the Coal Mines Regulation Act, 1912, as amended. The standards set down in that Act were based on the needs of the industry at the turn of the century. Changes and additions to the original standards have been made to cater for mechaniz- ation of the industry and the introduction of modern developments such as the use of diesel equipment. Technological progress has been recognized by the requirement for monitoring of machines and return airways. The passing of the Coal Mines Regulation Act 1982 has ensured that there will be a revision and modernization of the regulations affecting day to day operations of the industry.

Jan 1, 1983

By Eric R. Bauer

The U.S. Bureau of Mines, in cooperation with a southwestern Pennsylvania coal mining company, BethEnergy Inc., Mine No. 60, Eighty-Four, PA, recently assessed the feasibility of using pre driven recovery rooms (open entry recovery) when longwall mining to increase the productivity of the coal extraction process. Two recovery entries, one 200 ft long and another 600 ft long, were supplementally supported with bolts, channels, and wire mesh, and either fly ash-cement piers or fiber cribs, then mined into by the longwall face. The recovery entries showed little deterioration as the supports provided adequate resistance to the front abutment loading. Compared with conventional recovery methods, the fullface recovery room allowed for panel extraction to be completed nearly 17 days faster and to reduce face equipment move time by 1-1/2 days. The potential productivity increase accompanying recovery rooms is greater than the cost of supporting a fullface recovery room. The fullface recovery room provided over 18 additional production days and the opportunity to mine nearly 68,400 st of coal per year per panel mined.

Jan 1, 1989

By R. J. Mechin

IN the early part of 1934, the St. Joseph Lead Co. purchased from the Kadco Corporation three dust-removal units, two suitable for raise work, and the other for drifting operations. The equipment was installed at the Balmat mine, in St. Lawrence County, New York. The Kadco dust-control system can be briefly described as one in which hoods, through which the drill steel is drawn, control the dust at the drill hole, the dust is conveyed through rubber hose or pipe to a collector, where it is removed from the air stream, and the air is then available for recircula-tion in the working place. As during the last few years a number of studies had been completed for the purpose of determining whether or not the dust was effectively removed by the Kadco system, and as the dust counts taken in these tests apparently indicate that it was, the St. Joseph Lead Co. was only inter-ested in obtaining data to show the efficiency of drilling, expressed in terms of minutes per foot drilled, when -using Kadco equipment, in comparison with the former method of drilling dry in a raise and drilling wet in a drift. Comparative dust counts were taken at Balmat, however, by the Metropolitan Life Insurance Co. to show the difference in the dust content of the air in which the operators worked when drilling dry, wet, or with the Kadco equipment.

Jan 1, 1935

By Forest J. Sur

"This report describes an exploratory project conducted by the Bureau of Mines on a fluorite deposit near Vado, N. Mex. Results of trenching are given. Together with analyses made upon samples of the ore. The Federal Geological Survey3/ completed a preliminary geologic study and mapped the deposit during the summer of 1944. A Bureau engineer examined the deposit in August 1944. As a result of these investigations, it was concluded that the deposit contained substantial inferred ore reserves. Exploratory work was recommended to obtain information that might possibly lead to production from the property. Assistance was given the Bureau by the Geological Survey.A gasoline-powered air compressor, other equipment, and supplies were delivered to the property from January 20 to 25, 1943. Trenching began under the direction of a Bureau of Mines engineer on January 25, 1947, and ended on March 15, 1945. The results of trenching and sampling form he basis of this report.In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. IT is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, R.G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervisions of Dr. R. S. Dean, assistant director."

Sep 1, 1946

By Shadrack Nuamah, Erik Westman, Bright Afum, Jesse Addy

Rock fragmentation is the most critical aspect of hard rock production blasting due to its significant impact on drilling and blasting costs and the economics of subsequent loading, hauling, and crushing operations. This study analyzes current cost trends in the drill and blast operations of an anonymous open pit gold mine and proposes cost-effective drill and blast geometric parameters. The investigation focused on one operational pit with provided design parameters for two shots, shot 1 and shot 2. Existing blast parameters and two additional proposed sets of geometric parameters were evaluated using the Kuz-Ram and Chung and Katsabanis fragmentation models to estimate mean fragment sizes. The results indicated that the proposed blast parameters produced estimated mean fragment sizes within the mine’s desired range (not exceeding 45 cm). Additionally, the explosive energy was utilized efficiently per in-situ material blasted. The proposed parameters increased the estimated total volume of in-situ material fragmented by approximately 14% for both Shot 1 and Shot 2 compared to the current parameters. Furthermore, adopting the proposed blast parameters could lead to significant cost savings. The evaluated total drill and blast cost savings were approximately 11% for Shot 1 and 12% for Shot 2. These savings stem from the increased efficiency and effectiveness of the blast operations, highlighting the potential for substantial economic benefits. This study demonstrates that optimizing blast geometric parameters will allow open-pit mines to achieve desired fragmentation, utilize explosive energy more effectively, and realize considerable cost savings in drill and blast operations.

Jan 21, 2025

By Ali Porbaha

The use of soil nailing technology as a cost effective alternative for excavation support and slope stabilization has substantially increased in the United States during the last decade. For example, in the past thirteen years, more than 185,800 square meters of soil nail walls have been constructed in California alone. The conventional soil nail systems pose difficulties when ground conditions are subject to caving, for instance for silty sand (sugar sand) or cobbles and boulders. The construction industry has developed self drilling hollow bar systems (or pressure injected bored, IBO) that combine both drilling, placing and grouting in a single operation as a solution to speed up construction. While the system is extensively used for temporary applications, nevertheless, some concerns, particularly about corrosion, has limited the use of this technology as a permanent system in North America. This study presents several issues related to self drilling soil nail systems, the results of a field investigation and a summary of the research project.

Jan 1, 2006

By ALICE V. Petar

Thallium is one of the rare metals that has come into commercial use within recent years . Its comparative scarcity , combined with a resemblance to the common metal lead , have retarded the development of uses for thallium . Although production is still measured in pounds rather than in tons , it is now finding application in a number of fields . Perhaps the earliest commercial use of thallium was as a constituent of optical glass of higher refractive power than similar glasses containing lead . One of the later applications to attract attention was the use of the oxysulphide in a sensitive electrical device similar to the selenium cell . The " Thalofide " cell , which was patented in 1919 , constituted for a time the most important outlet for thallium. During the next few years the limited use of thallium and its salts in other fields was insufficient to absorb an annual production of a few hundred pounds , and the price dropped from $ 16 or $18 per pound in 1922 to $ 5 per pound in 1924 . Beginning in 1925 several new uses were developed , especially as a poison for rodents and ants , and as a result the demand for thallium increased sufficiently to cause a recovery in price to the present level of from $12 to $15 per pound .

Jun 1, 1931

By Gunter Fauth

The setting of tasks for the process control of coal cleaning, and in this connection the requirements for instrumentation can be classified into the following three fields: - Monitoring the operation of individual units, or process steps, - Control of units or process steps, - Control of the entire coal cleaning process with the intention of optimizing the operation and the profitability of the process. Instrumentation is affected by the type of cleaning processes. For introduction Figure 1 shows the simplified flow sheet of coal preparation which is usual in the German Ruhr District and in which desirable places for the measurement of ash, moisture and sulfur content are marked. The preparation plant is supplied with run-of-mine coal from the shaft via a homogenization facility. In a first step of primary classifying the raw feed coal is screened at about 10 mm. The raw coarse coal ( = 10 mm) is sorted by jig washers or heavy-medium separators. the raw fine coal (< 10 mm) at first is pneumatically sized at about 0.5 to 0.75 mm. The fines, the aspirated dust, are a finished partial product which will be added to the final metallurgical or steam coal. The material 10 to 0.75 mm subsequently is sorted in fine coal jigs and dewatered in centrifuges. The sludge obtained with the wet cleaning processes is dewatered in thickeners and fed to the flotation. Concentrate and tailings are dewatered by filters or bowl centrifuges and by chamber filter presses or belt filter presses, respectively. The partial products coarse coal, fine coal, flotation concentrate, aspirated dust, and middlings are blended to result in the sellable products metallurgical and steam coal.

Jan 1, 1984