Search Documents

By Gunter Fauth

The setting of tasks for the process control of coal cleaning, and in this connection the requirements for instrumentation can be classified into the following three fields: - Monitoring the operation of individual units, or process steps, - Control of units or process steps, - Control of the entire coal cleaning process with the intention of optimizing the operation and the profitability of the process. Instrumentation is affected by the type of cleaning processes. For introduction Figure 1 shows the simplified flow sheet of coal preparation which is usual in the German Ruhr District and in which desirable places for the measurement of ash, moisture and sulfur content are marked. The preparation plant is supplied with run-of-mine coal from the shaft via a homogenization facility. In a first step of primary classifying the raw feed coal is screened at about 10 mm. The raw coarse coal ( = 10 mm) is sorted by jig washers or heavy-medium separators. the raw fine coal (< 10 mm) at first is pneumatically sized at about 0.5 to 0.75 mm. The fines, the aspirated dust, are a finished partial product which will be added to the final metallurgical or steam coal. The material 10 to 0.75 mm subsequently is sorted in fine coal jigs and dewatered in centrifuges. The sludge obtained with the wet cleaning processes is dewatered in thickeners and fed to the flotation. Concentrate and tailings are dewatered by filters or bowl centrifuges and by chamber filter presses or belt filter presses, respectively. The partial products coarse coal, fine coal, flotation concentrate, aspirated dust, and middlings are blended to result in the sellable products metallurgical and steam coal.

Jan 1, 1984

Adsorption Effect on Multi-Heavy Metal Ions in Wastewater by Water-Washing Waste Saccharomyces cerevisiae

Sep 13, 2010

By Shail J. Butani

In 1986 the Bureau of Mines conducted a probability sample survey, Mining Industry Population Survey, to measure such employee characteristics as occupation; principal equipment operated; work location at the mine; present job, present company, and total mining experience; job-related training during the last 2 years; age; sex; race; and education. The population estimates are necessary to properly analyze the Mine Safety and Health Administration (MSHA) injury (includes illness and fatality data) statistics; that is, to compare and contrast injury rates for various subpopulations in order to identify those groups that are exhibiting higher than average injury rates. This report uses the survey&apos;s results to characterize the U.S. stone mining workforce from March through September 1986. Similar reports have been published for the metallic, sand and gravel, and nonmetallic mining industries, as well as for the entire metal and nonmetal mining (includes metallic, stone, sand and gravel, and nonmetallic industries) sector and the coal mining sector.

Jan 1, 1988

By W. T. Millar

Field reconnaissance and laboratory tests on clay from South Windsor, Hartford County, Conn., indicate that the clay is suitable for lightweight aggregate raw material. Exploration of the deposit supports the conclusion that the reserves of clay are sufficient for economical mining operations to produce lightweight aggregate. Preliminary tests indicated that the clay has a short bloating range. Initial expansion occurred at 2,000° F, and at 2,100° F the clay was slightly overfired and sticky. Rotary kiln tests verified the preliminary data, and these tests showed that the clay would make a good lightweight aggregate if the processing temperature and the kiln feed sizes were closely controlled. Lightweight concrete made from the processed aggregate had properties comparable to those of concrete made from a commercial clay aggregate.

Jan 1, 1964

By S. A. Shoop, J. J. K. Daemen

Site-specific blast vibration prediction can be more accurate than using a universal prediction equation. Vibrations from 37 blasts were monitored using three seismographs. Data analysis showed that square root, cube root, and site-specific scaling predicted ground motion with equal reliability. Imprecise prediction is caused by geologic and blast variability, particularly, inaccurate delay times. Vibrations at some mines were consistently lower or higher than vibrations predicted from US Bureau of Mines (USBM) equations. Vibration restrictions based on USBM studies could then be too conservative or too lenient. Predominant vibration frequencies were generally less than 50 Hz, but several blasts had significant energy up to 125 Hz. In some cases, energy was concentrated at frequencies corresponding to delay intervals.

Jan 1, 1985

By L. Gutierrez, R. Yepsen, F. Alarcón

Chile is the world's largest copper producer which is mostly in the form of sulfides for which froth flotation is the most efficient concentration process. As a result a concentrate that contains high concentrations of copper sulfides such as chalcopyrite, chalcocite and enargite is obtained. In the last decades processing of ores containing high concentrations of enargite (Cu3AsS4) has continuously increased in Chile, which is related to the fact that ore deposits nawadays are more heterogeneous and complex. Enargite is a mineral that contains arsenic and its presence in the copper concentrates implies severe penalties. In addition, the shortage of fresh water has driven the search for new alternative sources of water, among which seawater has proved to be one of the most attractive. The objective of this research is to study the behavior of the enargite in the process of flotation using seawater, and at the same time to compare its behavior with the results obtained using conventional water. The study was carried thorugh micro-flotation tests using pure samples of enargite, at pH values ranging from 4 to 11, both in fresh and seawater. PAX and MIBC were used as collector and frother respectively. Micro-flotation tests were also done at different redox potential conditions so that the effect of the surface oxidation of enargite was evaluated in seawater. The results indicate that the recovery of copper from enargite is reduced in seawater compared to fresh water, in particular at the pH values close to those of the formation of the first hydroxy complexes of Mg and Ca. In general, the experimental data indicate that the floatability of enargite is strongly affected when seawater is used, in particular at oxidizing conditions. These results suggest that Mg2+ and Ca2+ ions contained in seawater interact with the surface of enargite forming hydrophilic species.

Jan 1, 2018

Provide roof to floor closure rate measurements during underground mining, especially retreat mining of coal pillars, thereby helping the miners predict an imminent roof fall. Approach An electronic device and rugged potentiometric extensometer were developed to provide a means fur measuring total closure and the rate of closure. How It Works An intrinsically safe, battery operated instrument is enclosed in a rugged, hand carried field case. The unit is constructed using low-power, integrated circuits to provide minimal battery drain. Two digital Light Emitting Diode (LED) readouts are used; one displays the rate, the other displays the total closure. The unit will measure one extensometer continuously or two extensometers alternately. Two potentiometric extensometers with a closure measurement range of 6 inches are attached to the readout unit. As the roof to floor closure changes, the potentiometric resistance

Jan 1, 1982

By Lon Santis

In 1923, Ralph Assheton compiled a report for the Institute of Makers of Explosives (IME) on accidental explosions in manufacturing plants. The report chronicles the type and amount of explosive involved in the event and the effects and distances to nearby buildings and workers for over 100 events from 1880 to 1916. Apparently, this report was never published but served as the origin of the IME’s first intra-plant distance table published in Pamphlet No. 3 in 1926. The effort was a parallel effort to the IME’s development of the American Table of Distances. The intra-plant distance table has never been changed by the IME and follows the US Department of Defense (DoD) standard very closely. This paper freshly compiles the data from the 1923 report and analyzes it with modern methods not generally available in 1923. Interestingly, the analysis indicates that the original intra-plant distance tables were established primarily to protect workers from serious injury and that preventing propagation was a side benefit. The data shows that a strong relationship exists between the probability of injury and the traditional K-factor. The data indicate that people in the open are better protected than those inside structures and that barricades reduce risk close to an event. Individuals at the intra-plant distance had a 95 percent chance of receiving no worse than a minor injury. A comparison of the data to explosive event consequence models indicate the models are overly conservative in regards to risk inside inhabited building distances.

Jan 1, 2010

By David C. Oyler

Methane-drainage holes must be completely filled by grout before mining to prevent the emission of large quantities of gas during mine-through, which would constitute an explosion hazard. In November 1980, seven horizontal holes at the multipurpose borehole, a small-diameter shaft drilled as a Bureau of Mines coalbed methane-drainage installation on the property of the Federal No. 2 Mine, Monongalia County, WV, were plugged using a sodium silicate gel grout. This report de- scribes the grout mix and the use of the grout at the multipurpose borehole, and discusses the results observed upon mine-through of the holes in early 1981. Cost data for the sodium silicate grout are also presented.

Jan 1, 1984

By Dongjie Zhang, Shuxin Liu, Jianduo Wang

Broken rock mass and unreasonable stope structure parameters can cause excessive ore loss and dilution in sublevel caving; this is the main problem faced by caving mining in recent years. This paper proposes a stope structure parameter optimization method suitable for steeply inclined medium-thick broken ore bodies and evaluates the reliability and effectiveness through case studies. To solve the problem of large ore loss and dilution in the high-end wall sublevel caving method of Xilinhot fluorite mine, it is necessary to select proper stope structure parameters. Based on the theory of random media, an end-wall ore drawing experiment was carried out, and the bulk flow parameters needed to optimization of stope structure parameters were determined. In the experiment, it was found the draw-out body of high-end wall ore drawing showed a fine top and a thick bottom; the granular media had good fluidity. The reasonable caving step is determined to be 1.2 m instead of the 1.6 m originally used. Through the optimization experiment of the mining route position along the vein, the study found that the best route position is different with the ore body inclination. When the inclination angle of the ore body was 90°, the reasonable route was located in the center of the ore body. When the inclination angle of the ore body was between 85° and 90°, the route moved from the center of the ore body to the footwall at a rate of 22.5%. When the inclination angle of the ore body was between 80° and 85°, the route moved to the footwall at a rate of 54.8%. When the inclination angle of the ore body is not greater than 80°, the route should be arranged on the boundary of the footwall. Field application results showed the dilution rate reduced by 7.66% and the recovery rate increased by 7.31%. Field test results verify the effectiveness and applicability of the optimized stope structure, which corroborates the effectiveness and applicability of the optimized stope structure.

Mar 10, 2022

By George Burgess

1. Introduction.-THE methods of production of sound steel ingots have been described in several papers read recently before this Institute. It was thought by Director Stratton, of the U. S. Bureau of Standards, and ourselves to be of sufficient interest and importance, as a further contribution to this subject, to compare the properties of rails rolled in one mill according to American practice, from several types of ingot of substantially the same chemical composition but cast by several processes; and to compare in considerable detail the properties of an ingot manufactured by the Hadfield special-feeding process and one of the usual type for rolling into rails. We are greatly indebted to F. W. Wood, President of the Maryland Steel Co., who made this investigation possible by kindly placing his rail mill at our disposal; and he and his associates at Sparrows Point did everything possible to make the experiment a success, including the execution of several of the tests and analyses. 2. Classification and Manufacture of Ingots.-Of the ingots used in this investigation, eight were made in Sheffield and furnished by Sir Robert Hadfield, and one was made and furnished by an American steel company,&apos; as a comparison ingot, and was supposed to represent the usual type of ingot from which rails are made.

Jan 2, 1915

By N. A. Eilertsen

Among the numerous Low-grade manganese deposits in eastern Aroostook County, Maine, the Dudley deposit near Mapleton in the northern district is one of the few known to contain an appreciable tonnage averaging above 10 percent manganese. The ore body, consisting of stratified manganiferous hematitic shale, is over 5,000 feet long and ranges in width from 30 to 175 feet. The deposit was extensively explored during 1942-44 by the Manganese Ore Co., a subsidiary of M. A. Hanna Co. of Cleveland, Ohio. Data obtained from this work were made available to the State and Federal Geological Surveys for estimating ore reserves. An estimate by the Maine Geological Survey, using a 10-percent manganese cutoff and to a depth of 200 feet, shows 609,000 long tons of manganese metal in material averaging 12.6 percent manganese. By lowering the cutoff limit to 5 percent manganese, the estimate was increased to 919,000 long tons of metallic manga¬nese in material averaging, 10.4 percent manganese,

Jan 1, 1957

By Cornelius F. Kelley

AT the Annual Meeting of the A.1.M.E. last February, Cornelius F. Kelley, chairman of the Anaconda Copper Mining Co., was presented with the Charles F. Rand Memorial Medal for "conspicuous success as administrative head of great enter- prises engaged in the production of nonferrous metals at home and abroad; for inspiring leadership of an organization that has trained able engineers for service wherever ores are mined and metals are recovered; and for enhancing the prestige of metal mining in the financial and industrial world." Mr. Kelley&apos;s acceptance speech follows: I am not unmindful of the fact that the distinction is not to be considered a personal one, but that by the language of the citation itself it is rather a recognition of the service that has been performed by the many trained men of an industrial organization that in the arts of mining and metallurgy and in the fabrication of metal products has performed a distinct service to the industry and to mankind. In that spirit, the award is accepted, and on behalf of the organization I represent and myself, I thank you and assure you that the honor is deeply appreciated.

Jan 1, 1944

By C. L. Karr

Researchers at the University of Alabama are investigating artificial intelligence based computer models of mineral processing systems. Two approaches have been found to be particularly effective in developing data-driven computer models. The first approach employs neural networks which are computational paradigms based on the mechanics of the human brain. They are able to extract the basic relationships between input and output variables from large data sets. The second approach combines fuzzy mathematics with genetic algorithms to produce an adaptive modeling system. Fuzzy mathematics provide computers with the capability of manipulating abstract concepts like those which humans use so effectively in decision making. Genetic algorithms are search algorithms that mimic evolutionary processes apparent in nature. Together, these two techniques can be used to produce an effective modeling system. In this paper, the two approaches to modeling are compared and contrasted with respect to accuracy and computational time while used to model three mineral processing systems: (1) a grinding circuit, (2) a hydrocyclone separator, and (3) a flotation circuit.

Jan 1, 1997

By Carlos Aranda S

El presente trabajo describe el proceso pirometalúrgico convencional y actual en el tratamiento de los concentrados de cobre en el Perú. En ese sentido, se comparan los procesos antiguos con los nuevos, así como el uso de equipos últimos como el Outokumpo, Noranda,Hitsubishl, Worcra, TBRC, Klvcet y otros. De acuerdo a esto, los cambios se efectuaron solo en el tamaño de los hornos y se recomendó que en el uso de las dos fundiciones de cobre: CENTROMIN y Southern Perú Cooper Corp, se utilicen las tecnologías más adecuadas dentro de las condiciones menos óptimas y así competir con países latinoamericanos como Brasil, Chile y México.

Oct 14, 1980

The editorial expenses for the preparation of the manuscript of the second edition, as for the first, were provided by grants of the Engineering Foundation and the Open Hearth Steel Committee of the Iron and Steel Division, AIME ; the Seeley W. Mudd Memorial Fund again sponsored the publication of this volume. The companies and research or educational institutions with which the authors, reviewers, and editors are connected also contributed much to the writing and editing of this book through their generous donations of time and travel and office expenses. And finally, the authors and others have given countless hours of their own time with no recompense but the satisfaction of a job well done. In order to give credit to the companies or educational institutions which made it possible for the members of the Editorial Board to devote considerable time to the revision of this book, the names of these members and their affiliations are recorded here as follows : W. O. Philbrook, Carnegie Institute of Technology M. B. Bever, Massachusetts Institute of Technology H. B. Emerick, Jones and Laughlin Steel Corporation B. M. Larsen, United States Steel Company A number of individuals suggested desirable changes in the book before rewriting was started. Almost all manuscripts were gone over critically by reviewers, and the resulting criticisms led to the correction of errors and omissions and greatly contributed to the accuracy and completeness of the text. Other people have supplied additional data or illustrations or assisted in other ways. While some of these contributors must remain anonymous because they are not known to the Editors, the cooperation of the following individuals is gratefully acknowledged : R. D. Allen, Republic Steel Corporation, Chicago Isadore Amdur, Massachusetts Institute of Technology Mary Baeyertz, Armour Research Foundation S. P. Bahmer, Republic Steel Corporation, Massillon E. C. Bain and Associates, United States Steel Company, Pittsburgh C. W. Briggs, Steel Founders&apos; Society of America H. W. Briske, Wisconsin Steel Works

Jan 1, 1964

By R. Hogg, M. Polat, S. Chander

A fresh dust generator was designed and built in order to study the agglomeration behavior and other characteristics of freshly generated airborne dust. The size distribution of the freshly generated quartz airborne dust produced by the generator was measured both directly in air and after dispersion in water. It was observed that same dust particles had an apparently coarser size distribution in air than in water, suggesting possible agglomeration of the dust particles. It was also observed that the size distribution obtained by a cascade impactor was very similar to the liquid dispersed size distribution, implying deagglomeration by the impactor. The agglomeration was confirmed by microscopic observations of particles in air and those collected on a microscope slide. The extent of agglomeration played a decisive role on the fraction of the dust actually becoming airborne. It was also found that contamination of the airborne dust by the rolls of the crusher was almost twice as much as that of the product.

Jan 1, 1991

By Stephen Hodgson, Ken Brouwer

September 2005, Northern Dynasty Mines announced the discovery of a new, high-grade deposit at its Pebble project in southwest Alaska. The product of insightful geological investigation, Pebble East, as it is now known, is quickly growing into one of the most significant copper deposits in the world. Preliminary analysis shows it could reduce the U.S. copper supply deficit by a third. The new deposit has also altered Northern Dynasty’s view of how Pebble should be developed. This article describes the Pebble project as it is currently understood and outlines the work planned for the next several years.

Jan 1, 2007

The editorial expenses for the preparation of the manuscript of the second edition, as for the first, were provided by grants of the Engineering Foundation and the Open Hearth Steel Committee of the Iron and Steel Division, AIME ; the Seeley W. Mudd Memorial Fund again sponsored the publication of this volume. The companies and research or educational institutions with which the authors, reviewers, and editors are connected also contributed much to the writing and editing of this book through their generous donations of time and travel and office expenses. And finally, the authors and others have given countless hours of their own time with no recompense but the satisfaction of a job well done. In order to give credit to the companies or educational institutions which made it possible for the members of the Editorial Board to devote considerable time to the revision of this book, the names of these members and their affiliations are recorded here as follows W. O. Philbrook, Carnegie Institute of Technology M. B. Bever, Massachusetts Institute of Technology H. B. Emerick, Jones and Laughlin Steel Corporation B. M. Larsen, United States Steel Company A number of individuals suggested desirable changes in the book before rewriting was started. Almost all manuscripts were gone over critically by reviewers, and the resulting criticisms led to the correction of errors and omissions and greatly contributed to the accuracy and completeness of the text. Other people have supplied additional data or illustrations or assisted in other ways. While some of these contributors must remain anonymous because they are not known to the Editors, the cooperation of the following individuals is gratefully acknowledged: R. D. Allen, Republic Steel Corporation, Chicago Isadore Amdur, Massachusetts Institute of Technology Mary Baeyertz, Armour Research Foundation S. P. Bahmer, Republic Steel Corporation, Massillon E. C. Bain and Associates, United States Steel Company, Pittsburgh C. W. Briggs, Steel Founders&apos; Society of America H. W. Briske, Wisconsin Steel Works

Jan 1, 1951

By W. J. D. Stone

Discussions with people knowledgeable in the insulating material field revealed that materials on the market would be considerably improved if there was a greater meeting of certain very desirable criteria. Such criteria include: (1) the material should not burn, even at higher temperatures; (2) at an elevated temperature, the material should not give off toxic gases or produce smoke; (3) the material should have a low energy input; and (4) vermin would find the material unattractive. Theoretical discussions led to the conclusion that an insulating material made by foaming a mineral, preferably of a platy nature, with an inorganic binding system that could be converted to a rigid structure at low temperature would likely meet all the above requirements. It was also theorized that the use of microwaves in the converting stage would be beneficial in the creation of a cellular structure by aiding the foamer through creating vacules of steam. Talc was selected as readily meeting the theoretical mineral requirement and the material of Baker Talc Limited was used as the basic filler. The early results obtained led to an agreement between Americ Mines Limited and Baker Talc Limited pertaining to commercial production in a specific geographic area. It was recognized that due to the economics of shipping, the availability of the basic filler material should be geographically widely spread. Samples of materials were requested and many received from all over North America and one from Britain. Enough work has been done to show that they respond to the basic process in a similar manner as the Baker Talc material. From the data acquired, it is considered that the process is applicable for the production of loose fill insulation, moulded insulation for pipes and structural steel, ceiling tile, batts, sheet and for incorporation into other products such as various roofing board materials. Sufficient development has been done to enable a budget to be prepared for the construction and operation of a loose fill insulation plant.

Jan 1, 1979