Search Documents

By D. H. d Hamly

THE work of Brown and others at Pittsburgh (Brown, Baum, Yant, and Schrenk, 1938)(1) and the success of their light field microprojector (Figure 1), have shown that the microscopy of dust quantitation can be greatly improved. It has been shown that dark-field microprojection of dust spots on konimeter slides is possible (Pullen, 1940), and this paper is a discussion of the new microprojector and a new counting method which is made practical by this instrument. The microscope makes possible the ready determination of the dustiness of mine ventilation air. Reduction of the dust concentration from a dangerous to a safe level involves one or more of the following: reduction of dust production, filtration of the air stream, or dilution with non-dusty air. Each of these raises important engineering problems of time and costs, and trustworthy information on the state of dustiness of the air is required ?both before and after the employment of any method of reduction. Records of this information may be divided into two broad classes concerned with safety: (1) the level of dustiness, and (2) the quantity and kind of dust produced by a machine under a given set of conditions. Though the first requires only one determination for a given time and place, numerous routine records are required to show the continuous safety of the air in an actively producing mine. Though repeated samples are required, highly accurate counts are not needed to show safety or to indicate whether a substantial increase in the non-dusty ventilation air has produced a proportionate decrease in the dustiness of the mixed air. The Devers and Gathercole konimeters have proved satisfactory instruments for this purpose in Ontario.

Jan 1, 1942

By W. H. Coghill, F. D. DeVaney

"Introduction Numerous investigators have studied grinding. Each has contributed his bit to a literature that is difficult to correlate. Too many of the results have been transformed into curves with no many ""inflection points"" and ""counterflexures"" that they obscure the issue.Some of the investigators have neglected the very essence of the problem, namely, the power and the amount of material to which a known amount of work was applied. The purpose of this paper is to show the ease with which results can be interpreted when these quantities are duly recognized. Some grinding tests will be given for illustration.Grinding studies are of two kinds: (1) Study of the character of the ore and (2) study of the performance of the machines. Several ores may be crushed by a given machine, or several machines may be used on a given ore. The illustrations given in this report cover both objectives.Grindability Characteristics When the ores are being studied the information sought is grindability characteristics (grain-size distribution) and the grindability (work required to produce new surface) of a group of ores.When the study is of the machines, several machines are used for a given ore or given types of ores, and the grinding performances of the machines are compared by a grain-size study.Table 1 gives the grindability characteristics and grindability of six substances, one of which is coal. The substances are arranged from left to right in progressing order of tons per horsepower-hour. Curves and graphs are not needed for elucidation. The secret of the ease of interpretation is the order mentioned and the similarity of the sizing analyses. Power records must be complete in grinding studies.The grinding device was a ball, plunger, and mortar called the drop weight.' It may be used to advantage when the amount of material to be tested is too small for the orthodox machines.The upper part of table 1 shows the grindability characteristics by the cumulative-sizing analyses. Note how closely the percentage weights agree for a given sieve size. The lower part shows the grindability in terms defined elsewhere. The present paper should be read in conjunction with that paper."

Jun 1, 1934

By Madan M. Singh

This report presents the results of an investigation of inclined roof bolts, anchored over pillars, in room-and-pillar coal mines susceptible to shear failures of the roof. Although the field data do not support this contention, it is believed on the basis of analyses and other work that inclined roof bolts do offer potential under some circumstances.

Jan 1, 1978

Modern coal cleaning technologies have allowed coal preparation facilities to become quite efficient at removing sulfur compounds, waste rock and low grade coals from run of mine coal. Up to 50% of the raw mined coal stream may end up as refuse, particularly when the coal originates from longwall mining operations, or is high in partings, rock and impurities. The refuse materials vary from coarse materials removed by physical screening to very fine materials removed by floatation and density separation processes. Coal refuse piles are also known by a variety of other names including "waste dumps", "gob piles" and "slate dumps". The potential hazards of improperly reclaimed refuse include contamination of surface and groundwaters by acidic leachates and runoff, erosion and sedimentation into nearby watersheds, spontaneous combustion, disturbance of topsoil borrow areas, and damage from landslides should large slope failures occur. Many of these problems have been particularly acute for abandoned refuse piles, and modern regulations attempt to minimize the environmental impact of coal refuse disposal operations.

Jan 1, 1993

By A. F. Jolly

In an effort to better predict the useful service life of friction rock stabilizer mine roof bolts in coal mine environments, the Bureau of Mines has evaluated the corrosion resistance of stabilizer steels in air-saturated and deaerated waters from seven Eastern and Midwestern underground coal mines. Accelerated electrochemical corrosion tests were used to estimate corrosion rates for the two high-strength, low-alloy (HSLA) steels used to fabricate Split Set stabilizers and for galvanized steel. Long-term static-immersion weight-loss tests were also conducted with the HSLA steels. Corrosion rates developed from the weight-loss tests (steady-state air dissolution) were roughly comparable to rates determined from electro-chemical testing in aerated waters. Although the highest rates occurred in waters with the highest chloride contents, rates in the other waters were low (<2.0 mpy) and exhibited little correlation to the widely varied chloride contents of the waters. The generally low corrosion rates are attributed in part to the tendency to deposit a protective CaC03 film, reflecting susceptibility to carbonate precipitation as indicated by positive Langelier (saturation) index values for the waters. With one exception, corrosion rates for the galvanized steel were (2.0 mpy. Rates with aerated waters were higher than those with deaerated waters. Pitting tendencies of the steels were also estimated.

Jan 1, 1987

By Scott W. Hazen, Richard F. Link, George S. Koch

The Mi Vida mine , Big Indian district , San Juan County , Utah , is in an ore deposit of uranium and vanadium minerals disseminated in certain sedimentary beds of the Triassic Chinle formation . Statistical analysis of assays of samples taken from the ore body affords an estimate of the grade of the ore body and provides a prediction about the direction of best mineralization beyond the sampled area . The basic data analyzed are assay results for uranium ( Uз Og ) , vanadium (V₂O ) , and lime (CaO ) from 225 channel samples cut at 79 sample points . Through the use of appropriate statistical methods , particularly regression analysis , the grade of ore may be estimated more precisely than by conventional means , and the most favorable direction to extend the mine may be predicted . Frequency distributions of assay residuals for uranium , vanadium , and lime are compared to frequency distributions of assays without regard to trend . Correlations among these variables are obtained and interpreted . The statistical methods employed illustrate certain techniques that may be used to analyze assay data from ore deposits in general .

Jan 1, 1964

By Charles V. Jude

This U.S. Bureau of Mines report presents a review and evaluation of existing and new backfilling materials and methods for their applicability to the problem of gate road stress reduction in deep retreat longwall coal mines. Candidate backfill materials include pulverized coal combustion fly ash, flue gas desulfurization, and fluidized bed combustion by-products from coal-fired electric power generation plants. Properties of both backfill and its component materials are presented, with particular emphasis on the unconfined compressive strength and elastic modulus of backfill mixtures. Hydraulic mix designs discussed in this report include high-water content slurry and low-water content paste fills. Three gate road stress-transfer-modification concepts are proposed to reduce abutment stresses in gate road systems. The first concept, packwalling, involves packwall construction behind the headgate shield inby the face and adjacent to the headgate pillars. The second concept, gob-filling, involves infilling a strip of gob inset from and parallel to the headgate using paste injection methods patterned after a technology recently developed in Europe. In the third concept, entry-filling, slurry fill methods are used to fill abandoned gate roads and crosscut entries inby the face.

Jan 1, 1995

By Joachiim Lehner

The application of post-combustion (secondary oxygen) to avoid skull formation on BOF lances was tested in industrial trials. The main findings are that no negative impact on the metallurgical targets (i.e. carbon, temperature and phosphorus at end of blow as well as iron–oxide in the slag) could be observed. The technology is capable of avoiding the buildup of lance skull and consequently increasing the average life of lance tips. The application of post-combustion not only affects the skull formation, there are also interactions with the refractory lining, especially thermal wear, and the utilization of the process gases (CO Recovery) that have to be considered. Special attention has to be paid to the parameters determining the use of secondary oxygen because rather small changes can strongly affect the points mentioned above. Since August 2016, the PCD (Post-CombustionDistributor) lances are used on a daily basis in the steelplant LD3 in Linz.

Oct 30, 2017

By Xingang Wang

Spontaneous combustion is one of the most important safety issues in the global coal industry. It is considered to be a trigger for explosions in underground mines, especially for gassy mines. This thermal event is not easily detectable in the gob and sealed area. It is also a tough job to find the most likely hot point accurately. Admittedly, determination of the propensity for spontaneous combustion before mining activity should be a necessary step in the design of a mine and ventilation plan. However, due to the complexity of the chemical and physical properties of coal, spontaneous combustion has not been fully understood. According to a proximate analysis of coal, it is believed that sulfur and volatile matter in coal are the main intrinsic factors that cause the self-heating of coal. Their oxidation at lower temperatures than that of fixed carbon to initiate coal?s self-heating should be quantified. This study aims to improve the previous mathematical model developed by the authors for studying a coal?s propensity for spontaneous combustion. It enhances the model?s ability to consider the effects of sulfur, volatile matter and moisture content in the coal ? three important factors affecting a coal?s self-heating process. Based on the law of energy conservation, heat release rates for pyrite oxidation and moisture condensation are built into the model. Finally, the simulation results in terms of time versus temperature are calibrated with adiabatic testing data extracted from the literature for pyrite oxidation and moisture condensation, respectively. From the modeling results, it is found that the higher the pyrite content the coal contains and the more moisture that condenses in an environment with high relative humidity and initial temperature, the higher the potential for spontaneous combustion.

Jan 1, 2014

By AIME AIME

EVERYONE enjoyed the coal meeting and found it profitable. At least your correspondent did, and those to whom he talked. Close to a hundred were there. The Coronado proved an excellent headquarters hotel, though it is two miles or more from the business district of St. Louis; its Crystal Room was suitable for the technical sessions; its Lounge adequate for registration and informal chats; its Club Caprice made an artistic setting for the informal banquet; and its Coal Hole in the basement presumably served other needs-unfortunately we passed up an invitation to find out, and never got another. To be sure, the first day of the meeting (Monday, Oct. 28) was a drizzly one, but that only served to keep people inside where they belonged. Believe it or not, the first technical session was only five minutes late in getting tinder way, with H. N. Eavenson&apos;s words of welcome. M. M. Leighton then took over the conduct of the meeting, and invited Eugene McAuliffe to read his paper on how much coal the railroads are likely to use in the future. E. G. Bailey then presented some written discussion; among other things he wondered about the success of stokers on locomotives, and whether or not the burning of coal in locomotives could not he made a cleaner operation. Mr. McAuliffe pointed out that railroads are built to haul coal rather than to burn it. Maximum firebox efficiency is often subordinated to the traffic situation. Powdered-coal firing has not been a success because of limited firebox space. Stokers have resulted in economies indirectly, because large locomotives cannot he hand-fired and stokers thus make them possible. Nowadays it is not so important to do away with smoke, cinders, and soot, because most trains are sealed up and air-conditioned.

Jan 1, 1935

By J. Paraszczak

High productivity of the equipment employed is one of the key factors in reducing production cost in mining. One of the best ways to achieve it is an increase in availability. In order to identify the most adverse factors affecting it, reliability and maintainability analysis ought to be done. If its results are to be conclusive, a sufficient amount of credible and consistent data is indispensable. Following the experience from field studies done in underground mines, this paper discusses the current status of failure and maintenance reporting, as well as problems encountered. It exposes the importance of adequate data collection on failures and downtime as well as it reviews the benefits of analysis based on such material. The question of benchmarking with regards to mining equipment performance is also addressed. The paper concludes with some recommendations on data collection and processing, as well as stresses the need to standardize the most important reliability/ maintenance notions throughout the mining industry and to conceive appropriate performance measures.

Jan 1, 2000

By A. G. Darnley

"The Geological Survey of Canada is devoting consider-able effort to finding ways to make airborne radiometric measurements both quantitative and reproducible. Equipment has been designed by Atomic Energy of Canada Ltd. to provide high count rates in order to minimize statistical uncertainty, this being essential to justify applying terrain clearance and Compton scattering corrections to the data. Correction factors have been determined experimentally and can be applied automatically. Considerable ground work has been undertaken in parallel with equip-ment development in order to determine field parameters.Two airborne gamma-ray spectrometers are described. One is based on three 5-by 5-inch Nal(Tl) detector crystals and is used in a helicopter; the other employs twelve 9-by 9-inch detectors and is used from a Skyvan aircraft. The former is being used to investigate the range of radiometric response from specific rock types, and for the correlation of ground and air measurements; the latter has completed initial trials and will be commencing experimental surveys during 1969.Results are given to show the comparative sensitivities of the various detector sizes, and operational requirements for a gamma-ray spectrometer survey are discussed briefly."

Jan 1, 1970

By J. A. Herbst

A state of the art computer simulation package, named UTAH-MODSIM is being developed. This package can run on a mainframe (eg. UNIVAC) as well as on a microcomputer (eg. IBM/PC with at least 512 kBytes of core memory). Friendliness was the major concern in developing this software. The user simply generates a complete flowsheet by presenting the flowsheet on a graphics terminal. This flowsheet defines the circuit to be simulated. With the minimum required data, the user can obtain a complete mass and water balances within a few minutes. Moreover, this package will provide scale-up and capital cost information of specified equipment relevant to design. In order to illustrate the utility of this software, three design examples are given. They are: a) A typical multistage crushing plant. b) A reverse closed grinding circuit comparing one stage with two stage classification. c) A standard closed grinding circuit suitable to liberate a specified fraction of chalcopyrite from a copper ore.

Jan 1, 1986

By M. E. Ryan, C. L. Hoebbel, E. J. Haas

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Mention of any company or product does not imply endorsement does not constitute endorsement by NIOSH. ABSTRACT It has been suggested that effective disaster prevention and response in mining requires that elements of emergency management be incorporated into everyday operations, planning, and decision-making, much in the same way that the industry approaches routine risk management. Since Congress passed the MINER Act in 2006, the newly mandated structural and technological advancements in mine emergency response preparation have been made and are apparent, but measureable improvement in mineworker emergency preparedness is difficult to ascertain. To begin exploring whether measurable indicators of mine workforce preparedness can or should be addressed within a risk management framework, NIOSH researchers examined the datasets from two separate research efforts—one which measured the organizational safety climate and self-reported safety performance, and the other which measured individuals’ perceptions of their own self-escape competency. INTRODUCTION In response to the mine disasters in 2006, the United States Congress passed the Mine Improvement and New Emergency Response Act (MINER Act), which strengthened existing regulations [30 CFR, Part 48] and introduced new provisions to improve mine emergency response. Since that time, new technological and structural features, such as mandated redundant communication systems, personnel tracking systems, and lifelines in primary and secondary escapeways, have been installed in underground coal mines across the country. Additionally, mine operators are required to develop emergency response plans, provide adequate supplies of breathable air throughout the mine, provide more frequent and realistic expectations training, and are required to immediately notify the Mine Safety and Health Administration (MSHA) in the event of an accident. While the structural and technological advancements in emergency preparedness are readily observable and easily measured, levels of individual mineworker preparedness remain difficult to assess. There is a general consensus that deficiencies in competence in the non-routine tasks required for individual miners to effectively respond to a mine emergency likely remain (e.g., National Research Council [NRC], 2013), and NIOSH research continues address this concern (Haas, et al., 2015; Hoebbel et al., 2018). To maximize an operation’s capacity to effectively prevent disasters and/or respond to emergency events, it has been suggested that individual and emergency management efforts be incorporated into everyday operations, planning, and decision-making in much the same way organizations manage routine risks to health and safety (Haddow et al., 2017). To the authors’ knowledge, the mindful intersection of routine risk management policies and practices and emergency prevention and response readiness have yet to be empirically studied within the mining industry.

Jan 1, 2019

By E. W. Rouse

THE year 1936 has seen rehabilitation of many plants which had been closed or severely curtailed. The Steptoe smelter of the Nevada Consolidated Copper Co. has been transformed by a rearrangement of the flow of material and utilization of mechanical handling to a maximum. The Phelps Dodge Corp. reports the construction of newer and better reverberatories at the Copper Queen smelter, and of particular interest, a single high-pressure waste-heat boiler placed directly over the uptake. There has also been a complete reconstruction of the smelter at the Laurel Hill plant of the Nichols Copper Co.

Jan 1, 1937

By M. Mathey

The application of the Monte Carlo technique to production planning and everyday economic decisionmaking in mine production management is demonstrated. The logic is detailed using an example of underground production with continuous miners (CMs) and truck haulage. It is argued that availability of equipment and personnel are the predominant variables influencing mine output and productivity and that those availabilities may be well represented by binomial probability distributions. The probabilistic model is implemented in a standard Excel® spreadsheet with Palisade’s @Risk add-on to facilitate simulations. Starting from model calibration against data obtained from a mine’s annual reports, some general interdependencies of availability, utilization, productivity, and costs of production processes are outlined. Finally, several possible options and their consequences as regards production improvements are explored.

Dec 13, 2022

By C. G. McLachlan

INTRODUCTION The work described in the following paper was under-taken with a view to determining, if possible, the relative importance of some of the phenomena on which flotation seems to depend, in the hope that, if this information could be obtained, it would be of value in dealing with the problem as a whole. At the outset, brief reference will be made to three papers which had a considerable bearing on the course followed in the present investigation. In 1919, Langmuir, in a paper on &apos;The Mechanism of the Surface Phenomena of Flotation&apos;, showed that mono-molecular films of very great stability could be produced on solid surfaces with oleic acid, but that pure paraffin oil, though spreading readily on a dean dry surface, was easily displaced by water.

Jan 1, 1926

By A. Warczok

Metal losses in discard slag are the main factor determining overall recovery. The metals are present both in dissolved form and as matte or metallic inclusions, varying in size from 2 to 1000 µm. Pyrometallurgical slag cleaning usually consists of heating the slag, reduction of oxides and settling of matte/metal droplets. Heating the slag decreases viscosity and accelerates reactions. Reduction of magnetite liberates inclusions and facilitates co-reduction of dissolved metal oxides. A significant amount of the matte and metal is present as very fine metallic inclusions, too small for settling. The coalescence of these matte or metal inclusions is required to remove them from the slag. The developed new concept of slag cleaning combines DC furnace technology with an extra magnetic field for vigorous slag stirring, enhancing mass transfer to the reductant surface, accelerating the rate of reduction, and destabilizing the emulsion of matte or metal inclusions. Intensive slag stirring increases the probability of collision of inclusions, will accelerate their growth and will therefore improve settling. The process is carried out in a patented DC channel furnace, where the liquid metal or matte layer acts as a cathode and the floating coke bed on the slag surface is the anode. In the first part of the furnace, a superimposed magnetic field induces a Lorentz&apos;s force causing the slag to start an intensive circular motion. The next furnace zone does not experience any stirring and is dedicated for quiet sedimentation of the inclusions. A mathematical model of gravitational coalescence combined with forced slag motion showed the possibilities of effective removal of copper matte inclusions. The results of laboratory pilot scale tests of continuous slag cleaning showed fast slag reduction and confirmed the improved matte removal from the slag. Conceptual analysis shows the potential use of the technology in various other non-ferrous industries, like for example nickel plants. It is also possible to use this technique batch wise.

Jan 1, 2007

By W. H. Gauvin, N. J. Themelis

I N ADDITION to its practical importance in the beneficiation of iron ores and in direct-iron processes, the study of the reduction of iron oxides involves many aspects of challenging theoretical interest. The complexity of the reduction process combined with the fact that under different experimental conditions the controlling stage for the reaction may not necessarily be the same, has led experimenters in this field to a wide diversity of opinion regarding the reaction mecl1anism. As a rule, each investigation has been restricted to the study of one or two variables over a comparative]~• narrow range of experimental conditions, and consequently, it be-comes necessary to examine the significance of each published work in the light of the results of other experimenters in the field.

Jan 1, 1962

By Paul S. Goodman

This report examines the effectiveness of bonus plans in the coal industry. The analysis uses theoretical, literature review and empirical approaches to determine the impact of bonus plans on safety and productivity in underground coal mines. The basic finding is that the modal bonus plan in underground coal mining does not have a major impact on productivity and safety indicators. The design of the plan, or organizational factors, and the process of introducing the plan all contribute to its relative ineffectiveness. Strategies and options for designing effective plans are presented.

Jan 1, 1987