Search Documents

By K. C. Mills, R. Thackray

A test has been devised that can predict accurately the % crystallinity developed in a slag film formed between the steel strand and the mould. The % crystallinity in the test samples was determined and compared with that for slag films formed in the mould when casting with that flux. There was good agreement between the % crystallinity in the test samples and the slag films. It was found that additions of TiO2and ZrO2had little effect on the amount of crystalline phase formed, but additions of CaO caused a dramatic increase in the amount of crystalline phase formed. Various parameters (which can be calculated from chemical composition of the flux) have been plotted against % crystallinty in the test samples. It was found that the modified (NBO/T) ratio provided the best relation with % crystallinity for the various parameters tested. There commended relation is % crystallinity=141.1(NBO/T)-284.0. Keywords: continuous casting, mould flux, slag film, crystallinity, chemical composition

Jan 1, 2004

By C. W. Hancher, B. D. Patton, W. W. Pitt

"There are a number of nitrate-containing wastewater sources, as concentrated as 30 wt % NO3 and as large as 2000 m3/day, in the nuclear fuel cycle. The biological reduction of nitrate in waste water to gaseous nitrogen, accompanied by the oxidation of a nutrient carbon source to gaseous carbon dioxide, is an ecologically sound and cost-effective method of nitrate waste disposal. These nitrate-containing wastewater sources can be successfully biologically denitrified to meet discharge standards in the range of 10 to 20 g N(NO3-)/m3 by the use of a fluidized bed bioreactor. The denitrification bacteria are a mixed culture derived from garden soil; the major strain is Pseudomonas. In the fluidized-bed bioreactor, the bacteria are allowed to attach to 0.25- to 0.50-mm-diam. coal fluidization particles, which are then fluidized by the upward flow of influent wastewater. Maintaining the bacteria-to-coal weight ratio at approximately 1:10 results in a bioreactor bacteria loading of greater than 20,000 g/m3,This paper describes the results of a bio denitrification R&D program based on the use of fluidized bioreactors capable of operating at nitrate levels of up to 7000 g/m3 and achieving denitrification rates as high as 80 g N(N03-) per day per litre of empty bioreactor volume. IntroductionThe discharge of wastewater containing nitrate at concentrations greater than stipulated by the Environmental Protection Agency (EPA) creates an environmental hazard and constitutes a civil and/ or criminal legal liability.(I.2) At present, we have three options: (1) recycle and reuse of nitrate streams the total economic and technical balance should be Closely examined; (2) use of an alternative acid, which may pose an entirely different set of problems ; or (3) disposal of nonreusable nitrate sources by an environmentally acceptable procedure."

Jan 1, 1980

By Jan Willem van Bloois

IHC Merwede is world market leader in the construction of specialist dredging equipment; it is a company with a rich history. The Netherlands is a coastal western country for which water management is a very important issue. Without the enclosure of the coastal areas with dikes and dunes almost two third of the Netherlands would be flooded. These activities are mostly performed by the dredging industry and are the foundation of the dredging industry as it is today. Besides land protection this industry also carries out infrastructure maintenance and performs land reclamation projects. In essence the dredging industry is specialized in horizontal excavation activities and operations in shallow waters with the purpose of gathering bottom sediments and disposing it at a different location. The development is that the activities are moving to deeper waters to a depth of up to 150m. A few years ago IHC Merwede received a request to perform the shallow water excavation techniques at a depth of approximately 2000 meters for the deep sea mining market. In response to the increasing number of requests for deep sea dredging and mining application solutions, IHC Merwede combined all of its activities in this sector to create a new, specially equipped operational unit, IHC Deep Sea Dredging & Mining (IHC DSDM).

Jan 1, 2010

By Cyril Smith

A STUDY of the precipitation-hardening of copper steels1 led the authors to investigate malleable iron containing copper, for the low-carbon ferritic matrix in malleable iron should lend itself admirably to precipitation-hardening. It was soon found that in addition to rendering malleable iron susceptible to improvement by precipitation-hardening treatments, copper has another potentially useful effect as an accelerator of graphitization. Brief mention of these effects was given in a general paper by Lorig and one of the present authors2; the present paper gives further details on the graphitization and precipitation-hardening effects only. After the completion of this work a paper by L. Lykkin3 appeared, confirming the authors' conclusions regarding graphitization.

Jan 1, 1935

By J. -C. Tricket, W. A. Düweke, S. Kock

The high-resolution three-dimensional (3-D) seismic reflection data acquired for Impala Platinum between 1998 and 2002 in the western Bushveld Igneous Complex form an integral part of Impala?s mine planning and development programme. These data are of sufficiently high quality to provide unprecedented 3-D models of the geological structure of the Merensky Reef and UG2Chromitite Reef, from which the mine deduces the size, geometry and distribution of mineable blocks. Conversely, the seismic data details zones of un-mineable ground caused by structural disturbances in the form of potholes, fault zones and pegmatoid intrusions. Furthermore, variations in dip and strike are well imaged, allowing the mine planners to optimize the mine design and layout. Current interpretation work is focused on enhancing the accuracy of these geological model seven further through the analysis of ?seismic trace attributes.? Preliminary testing on the Impala Platinum 3-D seismic volume has shown that attribute analysis has the potential to illuminate a number of geological reef disturbances that are otherwise ?invisible? in the original seismic time volume. Potential areas of improvement include inter alia: ?Improved definition of major fault zones ?Improved definition of zones of reef depression (?slumping?) ?Identification of reef terracing and/or reverse dip.. Keywords: 3D reflection seismics; Impala Platinum Ltd; seismic attribute analysis; Seismic Micro Technology (SMT); rock solid attributes; dip-azimuth; instantaneous phase and similarity.

Jan 1, 2004

By V. A. Evans, D. L. Hellier

Introduction Preparing a report on fluorspar economics in the US could have been somewhat complicated at one time. This was because the number of producers, both large and small, derived production from different locations through-out the western US and the southern Illinois and western Kentucky fluorspar districts. Companies, such as Allied Chemical and Williamson Mining, operated in the Jamestown district of Colorado. In Walden and Salida, CO, the Colorado Fluorspar Co. operated mines and mills. In New Mexico, both Du Pont and Allied had mines and mills. In the Illinois-Kentucky district, US Steel, Rosiclare Lead and Fluorspar, Minerva Oil Co., and Marathon Oil all produced spar for the US market. Now all of the companies are out of the fluorspar business and, with the closing of the Seaforth Mineral Co.'s Inverness Mining Co., only Ozark-Mahoning Co. survives as a domestic producer. History Ozark-Mahoning Co., as it now exists, was formed in 1946 by the merger of Ozark Chemical Co. and Mahoning Mining Co. Ozark Chemical Co. was started in the 1920s to produce sulfuric acid for two refineries located in Tulsa, OK. Mahoning Mining was originally formed by the founders of Ozark Chemical Co. and the Youngstown Sheet and Tube Co. to produce fluorspar and associated minerals from properties in the southern Illinois and western Kentucky fluorspar district. In 1937, Mahoning Mining started an exploration program, employing contractor-operated churn drills to look for reserves in Hardin and Pope Counties in southern Illinois. Based on known reserves in the area and the results of the exploration program, work was started in the fall of 1938 to build a selective flotation plant at Rosiclare, IL. The mill was completed and put into operation in August of 1939. The company's first mining efforts were in the Cave-In-Rock district just north of Cave-In-Rock, IL. The deposits in this area were of the Manto or bedded type. They have been the mainstay of the company's operations in the Illinois-Kentucky fluorspar district. In 1950-51, the company expanded its operations by purchasing fluorspar properties from Colorado Fluorspar Co. at Walden, CO. This location was operated from 1952 through 1958 and from 1968 through 1973 when it was closed permanently. In 1974, Ozark-Mahoning Co. was purchased by Pennwalt Corp. Presently, it is a wholly-owned subsidiary of that corporation. As the only major domestic producer of fluorspar in the US today, the company's ability to survive under the flood of imported material is directly related to the four major segments of its operations. These are: exploration, mining productivity, maintenance, and marketing. All are done in-house. Exploration The Southern Illinois fluorspar district is located in the most complexly faulted area of the central US. The formations are sedimentary in nature and range in age from Devonian through Pennsylvanian. The deposits are small, they range in size from a few thousand tons up to 900 kt (1 million st), with the average minable deposit being around 544 kt (600,000 st). The ore occurs in both nearly vertical vein deposits and in Manto or flat lying bedded deposits. Due to the relatively small size of the deposits and the depth at which they occur, a good low-cost exploration program is essential to ensure that new finds of ore are equal to the mining extraction rate. Ozark maintains a leased land position in Pope and Hardin Counties that will fluctuate somewhere between a low of 40 km2 (10,000 acres) up to a high of 129 km2 (32,000 acres), depending on total size of tracts leased. Most all lands are obtained through a standard lease purchase option, with a small minimum royalty per acre during the normal 10-year option period. All leases are standard and without deviation to control land cost. All land leasing is done through Ozark's geological staff, who also

Jan 11, 1986

By the use of flotation tests it was confirmed that there are two functions of oxygen in sulphide mineral flotation. Sized samples of galena and chalcopyrite were sulphidized, washed free of excess sulphide ion, and then contacted with air-saturated water for certain lengths of time. The mineral was then transferred to a sealed laboratory flotation cell containing water with a known concentration of dissolved oxygen. Xanthate and frother were added and flotation continued for 1 min.Both the extent of mineral oxidation and the concentration of dissolved oxygen markedly affected the flotation of galena and chalcopyrite. The response to a change in either variable is dependent on the level of the other, but generally best flotation occurs with the maximum degree of air saturation of the pulp. Galena flotation is hindered by oxidation of the mineral beyond a small threshold amount but a similar effect for chalcopyrite was not observed...

Jan 1, 1967

By Arthur Taggart

FLOTATION of sulphide minerals and native metals is no longer a practical difficulty. The underlying scientific principles of the method, although not explored in anything like complete detail, have been formulated with sufficient breadth so that the direction of attack on any specific case is clearly indicated. It has been known since the earliest clays of flotation that certain of the nonsulphide nonmetal minerals-e.g., sulphur and graphite-would respond to flotation by oils as sulphides do; therefore they have been grouped with sulphides in many patents. But since the development of the chemical theory of collection,1,2,3 this similarity in action has been one of the facts cited in disproof of the theory by opponents of the hypothesis.4,5,6 Air levitation? of certain oxidized minerals, both metalliferous? and nonmetalliferous, and separa-tion thereby from other oxidized minerals, is a recent development in practice, although the discovery of the method dates back 17 years.7 This paper presents evidence that the principles underlying the air levita-tion of the nonsulphide nonmetal minerals are the same as those utilized in the flotation of the sulphides and native metals. It will be apparent immediately to anyone with knowledge of mineral concentration that separation of air-levitated minerals in water from minerals not so levitated is a simple matter of water-gravity concentra-tion, the separating device employed depending solely upon the size of the particles treated and the buoyancy differences effected by the levita-tion, The usual separating means employed are: (1) a flotation machine for fine, slimy and for well aerated granular material; (2) shaking tables for granular less aerated material.

Jan 1, 1937

By Roy Bartholomae

Noise generated by continuous mining machines in underground coal production is an important health hazard. Bureau of Mines Contract J0387229 covers investigation of this noise through laboratory tests of simulated cutting operations and through in-mine noise measurements. The results of these investigations indicate that coal cutting noise and conveyor noise are dominant sources of mining machine operational noise. Typical noise levels for both cutting and conveying operations are approximately 97 dBA (decibels A-weighted). For full operation of all machine systems, the overall sound pressure level is approximately 101 dBA. In-mine and laboratory test results show excellent agreement in both A-weighted overall levels as well as in A-weighted one-third-octave band spectra.

Jan 1, 1983

By Nikhil Dhawan, Veeranjaneyulu Rayapudi, Singh Rahulkumar Sunil

The ever-increasing demand for steel and the subsequent depletion of high-grade ores requires the massive utilization of low-grade iron ores. In the present study, an iron ore slime sample containing 56.1% Fe was investigated using physical beneficiation, carbothermal reduction, and a microwave-assisted process; however, physical beneficiation and microwave exposure were found to be inefficient as they yielded lower iron recovery. Using coconut shell as an alternative reductant was found to be promising and does not lead to the formation of higher iron oxides, such as fayalite and wustite phases. The microwave-assisted carbothermal reduction was found at par with conventional reduction, saving time and heating. The optimum magnetic concentrate obtained in both carbothermal reduction routes (microwave and muffle furnace: Fe grade, Fe recovery, and yield of 64.3, 97, and 84%, and 67, 99, and 83%, respectively) are suitable for alternative iron-making or blast furnace units.

By Michael Louis, Charles Dowding

Concern over construction vibration-induced cracking has led to development of a new approach to vibration monitoring called autonomous crack measurement (ACM) and illustrated in Figure 1. This paper describes the concept as well as sensor performance in the first test house fitted an ACM system. Response of three cracks in this concrete masonry unit (CMU) house was measured as part of the system verification. ACM employs a single sensor that measures both weather-induced micrometer changes in crack width and those produced by habitation and ground motioninduced vibration. This comparison is displayed in real time via the Internet without human interaction. Graphic display through the Internet provides a new pathway for communication with the public. Such visual comparison of changes in crack width provides a simple alternative to the present system of comparison of measured and allowable vibration time histories. Measurements reported herein show that weatherinduced response of cracks is greater than that caused by presently allowable construction-induced vibration.

Jan 1, 2003

By D. B. Robinson, C. A. Macrygeorgos, G. W. Govier

Experimental data have been obtained on the volurrletric behavior of ternary mixtures of methane, hydrogen sulfide and carbon dioxide at temperalures of 40°, 100" and 160°F up to pressures of 3,000 psia. The results indicate that the compressibility factors for this system do not agree with compressibility factors for sweet natural gases at the same pseudo-reduced conditions. The deviation increases as the temperature and methane content decrease. Discrepancies of up to 35 per cent were observed. A careful analysis has been made of the existing pUrblished data on compressibility factors for binary systems containing light hydrocnrbons and hydrogen sulfide or carbon dioxide. It has been found that the deviation of actual from predicted compressibility factors for methane-acid gas mixtures is a function of the methane content and the pseudo-critical properties,.v of the mixture. The ratio between actual compressibility factors for methane-acid gas mixtures and compressibility factors for sweet natrlral gases at the same pseudo-reduced conditions has been currelated over a range of pP,, from 0 to at least 7 arid a range of pT, from about 1.15 to at 1east 2 0 with an error not exceeding 3 per cent and over most of the range within I per cent. The validity of the correlation for mixtures containing appreciable hearvier hydrocorbons has not been fully established, but it is shown to be preferable than the use of a corretation based only on hydrocarbons. INTRODUCTION Although a relatively accurate method for predicting compressibility factors of pure materials is provided by charts based on reduced properties and the assumption that the compressibility factor is a unique function of T P and z the determination of the correct values of compressibility factors for gas mixtures is somewhat difficult. Two general methods of dealing with gaseous mixtures have been proposed. The first assumes a direct or modified additivity of certain properties of the mixture in terms of the properties of the individual components. Examples of this method are based on the familiar laws of Dalton and Amagat. The second method averages the constants of an equation of state applicable to the pure components. Both of these methods are of limited value in engineering calculations because the first usually provides reliable answers only over narrow ranges of pressure and temperature and the second is cumbersome to handle. In petroleum engineering practice accurate estimations of the volumetric behavior of natural gases arc frequently required. To fulfill this need, several generalized compressibility charts have been developed.' ' Of these, the one prepared by Standing, el al is widely used at present. In the construction of charts of this type a third method for dealing with mixtures has been followed. It is based on correlation of pseudo-critical properties as outlined by Kay and calculated from the critical properties of the individual components in a mixture. Although these charts provide relatively accurate information on the compressibility of dry or wet sweet natural gases, they are less reliable when used for gases containing high concentrations of hydrogen sulfide or carbon dioxide or both. Thus, an experimental program, although time consuming, is the best means now available for the determination of the volumetric behavior of sour or acid gas mixtures. An increased interest in the behavior of these gas mixtures, particularly in connection with some of the fields in Western Canada where the acid gas concentration of the reservoirs may be as high as 55 per cent and where hydrogen sulfide alone may be as high as 36 per cent, provided the incentive for this study. It was the purpose of the investigation to determine the volumetric behavior of selected mixtures of methane, hydrogen sulfide and carbon dioxide over a range of temperature from 40" to 160°F and at pressures up to 3,000 psi. EXPERIMENTAL METHOD The apparatus used in this investigation was basically the same as that described by Lorenzo.'" The amount of each pure component used in preparing the gas mixtures was measured over mercury in a glass-windowed pressure vessel. The pure components were then transferred individually in the desired amounts to a second glass-windowed pressure vessel where the volumetric behavior of the mixture was determined. Volume was varied by mercury injection or withdrawal. The capacity of the cell was about 125 cc. Temperatures in the cells were measured with copper-constantan thermocouples and a Leeds Northrup semi-

By M. Moats, J. A. Gonzalez

A review of operating practices in zinc electrowinning plants is presented in this paper. Surveys were sent to several zinc electrowinning plants and data provided by some of these plants was compiled in a database. Information about anodes and cathodes, electrolyte composition, stripping methods, cells, electrical systems, and additives was compiled and analyzed. From the data analysis, correlations between operating variables are presented. Recent trends in operational practices are also highlighted.

Jan 1, 2008

By Thomas S. Lovering

Hot springs, geysers, steam-emanating fumaroles- these creatures of nature were until recently little more than geological curiosities, but today they are exciting the interest of engineers around the world for it has been shown that such hyperthermal areas can be profitably harnessed by man to provide heat and power for his communities. Although water from hot springs was used centuries ago to heat some Korean dwellings, is being used today by one-third of Iceland's population for similar purposes, and is finding industrial applications in New Zealand and elsewhere, the most dramatic use of geothermal energy has been its conversion into electricity. The largest installation at the present time is that at Larderello, Italy, where the Count of Larderello began to experiment in the production of electricity from geothermal steam in 1904. Eight years later after a quarrel with the local power company, the Count installed his first steam turbine, a unit of 250 kw capacity.

Jan 9, 1965

Spectroelectrochemical Investigation of Hydroxamate Reagents on Copper Oxide Minerals

Sep 13, 2010

By Richard E. Gray

Subsidence due to coal mining is poorly understood by non-specialists. This has led to numerous misconceptions and myths based on limited observations and lack of knowledge. The three most common are: 1. Mine maps are inaccurate. 2. Deep mines are not a problem. 3. If no subsidence has occurred for many years after mining, there is no risk of future subsidence. Maps are important during mining and most are carefully prepared. Future use to evaluate conditions at mine level often includes drilling to confirm what the map shows. Usually, little or no effort is made to tie the surface survey of the property to the mine survey, to conduct a well designed drilling program to confirm the mine map, or to drill test borings vertically. When a mine entry is encountered rather than a coal pillar, or vice versa, and conditions at mine level appear different than anticipated, the first reaction is the mine map is inaccurate. The idea of a safe depth from subsidence is often based on the false premise that mining results in sufficient breakup of the overlying rock strata that bulking compensates for the coal extracted. The safe depth idea first appeared in the literature about 1880 and remained prevalent well into this century. Sadly, it is still encountered. The modern understanding of fragmentation of the immediate mine roof with the overlying beds sagging down on the broken roof rock was first described in 1900. With full extraction mining, either longwall or retreat room and pillar, surface subsidence occurs regardless of the depth of the mine. Subsidence over longwall mines at depths of 2000 feet can be 90 percent of the mined seam thickness. Numerous studies of undermined sites conclude that mining occurred many years ago and since no subsidence has occurred, there is no risk of future movement. This is true if sufficient coal pillars have been left to support the overlying strata. However, every year subsidence occurs over mines that have been closed for 100 years or more. In a study of subsidence incidents over the Pittsburgh Coal, the senior authors found that 50 percent of the incidents occurred above mines that had been closed for at least 50 years and 10 percent over mines closed for at least 80 years.

Jan 1, 1996

By K. S. Mortensen

The softwall mining system is a novel, new method of mining mineral deposits in soft, shallow, nonrock ground conditions. This method can mine the ore layer without substantially disturbing the existing overburden. The softwall mining system consists of machinery that is hydraulically controlled and powered, that can be buried (or used on the surface) to extract the ore or mineral from a layered deposit. The method is essentially an application of the longwall mining concept, modified for loose overburden and ore conditions, combined with hydraulic mining.

Jan 1, 2003

By Anthony Peach, Lok Home

Introduction Raise boring is the most accepted form of mechanized hard rock boring in the mining industry. It appeared logical to take this mechanization one step further by introducing computers. Atlas Copco Jarva has produced a series of raise boring models that use an integrated computer. The company decided to use electronics and computerization, not for marketing purposes, but to make its equipment more cost-effective. Basis of Cost-Effective Design From the manufacturer's standpoint, it is possible for the equipment owner to reduce the cost of putting in raises by: • Replacing existing components with less expensive components that produce the same results; • Replacing existing components with more expensive components that make the equipment more productive; • Mechanizing equipment to reduce associated labor costs; and • Combining the above. Analysis of a standard raise boring machine (RBM) system showed that little could be done with less expensive components. It appeared, however, that the RBM could be more productive by transmitting more horsepower through the expensive drill string, while being precisely controlled by computers. An RBM system includes a basic machine, drill pipe, accessories, reamer, and cutters. The approximate percentage cost of various components on a standard system capable of boring 300 m (985 ft) long and 3-m-diam (10-ft-diam) aises in medium to hard rock is shown in Table 1. Also shown is the increased cost above standard of the Jarva computerized machine, and the productivity of both. Increased Productivity Penetration is important during the reaming cycle for more productive raise boring. This is possible by increasing the cutter load with constant rpm or increasing the rpm with constant cutter load. To increase thrust and maintain rpm requires increased capacity in the cylinders, drive train, main thrust bearings, drill string, electrical motors, and power units. To increase rpm and maintain cutter load requires only increased capacity in the electrical motors and power units. This is possible because the torque requirement remains constant for a constant thrust load. Only the horsepower increases, proportional to rpm. Since cutter costs are a big factor in raise boring, changes in machine performance must be analyzed to assess the effect on cutter performance. With a standard or typical carbide cutter, as used on raise boring machines, the effects of increased thrust or rpm are shown in Table 2. The assumption is made that the base data is the current rpm and thrust range where the cutters are now operated. It is also assumed one variable is held constant while the other increases. The result of this comparison, approximately, is that a 50% penetration increase can be achieved with little or no increase in cutter cost if rpm is increased 50% and cutter load is maintained constant. A similar 50% penetration increase can be achieved with a 45% increase in cutter cost, if the cutter load is increased by 20% and maintained constant. From an equipment standpoint, it is significantly less expensive to increase rpm 50% than it is to in-

Jan 7, 1984

By T. B. Armstrong

"The developing world energy crisis and spiraling fuel costs have created a new public awareness and general acceptance of the need for energy conservation.Plants will have different objectives for an energy conservation program but there appears to be a common approach on how to save electrical energy.Data for a 180tph Rod Mill powered by a 750 hp motor will be used to demonstrate the relationship of energy input and production levels and to seek an optimum operating condition.Energy Conservation:Plants that have examined ways of dealing with the energy situations have concluded that energy conservation has important benefits for industry, including reduced costs, fewer production slowdowns inthe event of fuel shortages and a continued competitive position.There have been some ""startling"" conservation achievements attained through such simple plant maintenance and operating practices as reducing unnecessary lighting in buildings and yards, turning off' equipment not needed at night or over week-ends, through planning maintenance and production schedules to minimize energy use and through improving quality control to eliminate waste.Significant reducti.ons in energy use have been achieved by some rather simple but vigorous maintenance and plant engineering efforts directed at finding and fixing energy ""leaks"" rather than technological advances or major rework or redesign of facilities and equipment.An Energy Conservation Program often must overcome such obstacles as historic operating practices and emp1-oyee indifference, i.e. the ris.ing costs of fuel should result in re-examination of so1ne basic attitudes to energy conservation. Some measures, rejected in the past largely on the grounds of capj.tal. expenditure, now make economic sense in the light of future escalating energy costs."

Jan 1, 1978

By T. Backers

In fracture mechanics modeling the rock mass is seen as the combination of rock material and fractures, which are evident on different scales. The activation and propagation of fractures dominates the stability and performance issues as well as fluid flow potential. Once fractures have started to grow into each other and create through going separations, stability of rock engineering constructions may be violated. Further, as fracture mechanics inherently incorporated a scaling law in the form of the participating fracture length, scaling issues can be more accurately mirrored. This contribution highlights some examples of application of a fracture mechanics based code on some rock mechanics issues such as numerical laboratory experiments, borehole stability or the creation of fluid pathways due to underground constructions. The results show explicitly the creation of fractures and connection of existing ones, and hence the safety and performance issues. It has to be concluded that the basis for frequent application of fracture mechanics on specialized challenges in Geomechanics is laid, and the needs for future developments are defined.

May 1, 2009