Search Documents

By Francis M. Walters

IN spite of the war and the preoccupation of many physical metallurgists with work on secret or confidential problems, definite progress was made during 1944 in our understanding of the behavior of steel and of the effect of alloying elements. During the first two years of the war there was much concern over the possible unavailability of certain alloying elements; this period saw the development of the N.E. (National Emergency) steels. However, the measures taken eased the alloy situation and currently, highly practical problems under study are the graphitization of low-carbon steel and weld-cracking, while investigations of more theoretical interest have concerned hardenability, isothermal reactions, the effect of hydrogen and the interpretation of the notched-bar impact test.

Jan 1, 1945

By Meisam Ghiasi, Mohammadreza Khalesi, Mahmoud Abdollahy

In the current research, isothermal experiments of kinetic analysis were performed at different temperatures (800–1050 °C) and particle sizes (885 to 10,763 μm) to investigate the calcination kinetics of high-purity limestone. Thermal analyses were carried out in a zirconia crucible, 1 cm in height, for different temperatures and particle sizes. The reaction rate coefficients were varied in the 2.2 × 10−5-1.62 × 10−3-m0.6.s−1 range. Moreover, various isothermal kinetic analysis methods were applied to assess the decomposition mechanism and the calcination function governing the process. The modified shrinking core model was found as the best representation of the high-purity limestone kinetic data. The activation energy was evaluated using the Arrhenius curve, and an average value of 86 kJ.mol−1 was obtained.

Sep 15, 2020

By J. A. Gutierrez-Rodriguez, R. J. Purcell, F. F. ApIan

"Based on contact-angle measurements and the work of adhesion equation, the hydrophobicity of a wide variety of coals was found to decrease with decreasing rank, fixed carbon and total carbon content and with increasing oxygen and hydroxyl content. The estimated hydrophobicity, based on the water-sessile-drop contact angle, is '\.. 20% for lignite, increases with increasing rank up to a maximum of 'V70% for low (LV) and medium (MV) volatile bituminous coals and then decreases somewhat for anthracite. Using the captive-bubble technique, the calculated hydrophobicity ranges from '\.. 0% (below HV A bituminous rank) to a maximum of 55% for L V-MV coal. The former estimation is believed to be the more accurate. While the water-sessile-drop contact angle as measured on a polished-coal surface is usually larger than that shown by the captive-bubble method, the two values were found to converge at""' 95% relative humidity. It is proposed that the surface of coal consists of three kinds of sites: strongly hydrophobic, weakly hydrophobic and hydrophilic. The sessile-drop technique measures the total hydrophobic sites whereas the captive-bubble method measures only the more strongly hydrophobic sites. A water film covers the weakly hydrophobic sites preventing their detection by the captive-bubble technique.INTRODUCTIONCoal is a mixture of the degradation products of plants and of mineral matter. The appearance and properties of a specific coal is determined by the nature of the original vegetation and the extent of the physical and chemical changes which have occurred after deposition. The coalification process may be considered to have started with peat formation followed by a transition to lignite due to burial under sediments and metamorphic processes. Further metamorphic transformation to bituminous coals and, finally, under intense metamorphic action, to anthracite causes the carbon content and rank of the coal to increase. With such a wide variation in their genesis and composition, equally wide variations in the degree of hydrophobicity of different coals may be expected. It is the purpose of this paper to provide a means of estimating the hydrophobicity of a given coal sample based on rank parameters."

Jan 1, 1989

"Real-time, on belt analysis of minerals is becoming increasingly important and critical in modern operations, especially in the mine-to-mill. Prompt gamma neutron activation analysis has long been utilised for real-time elemental analysis in bulk materials, with Scantech's GEOSCAN being the instrument of choice in the minerals sector. Working in the minerals space for 15 years, the GEOSCAN has been successfully implemented in a wide range of minerals applications including iron, copper, lead-zinc, manganese, phosphate and more, and it caters for the very high demands and increasing requirements of a contemporary processing facility. An area of focus has been on increasing the analysis frequency to allow for rapid analysis results with the same high degree of accuracy typically expected of the GEOSCAN. This paper discusses the underlying research and technology that has enabled such rapid analysis and presents a range of examples using a thorough statistical approach on real production material, demonstrating achievable accuracy over a short analysis time, and dispelling common myths about the speed of the technique. Potential applications are discussed to conclude the paper.INTRODUCTION Technology and the information it can provide plays a critical role in the evolving modern mineral processing landscape. The importance of technology to analyse various features of ores and concentrates being processed is obvious, and recent years has seen the advance of numerous technologies to provide a variety of real-time measurements on conveyed material flows. From sampling apparatus to particle size analysis to weight and density meters to full elemental analysis, the availability of information enables a variety of improvements in the process leading to improved efficiency and increased revenue. To maximise the potential benefits, access to real-time information is imperative, and rapid updates of information become necessary to make appropriate process control decisions based on the most relevant and up-to-date information."

Jan 1, 2017

By B. McFadzean, J. Taguta

The enthalpy of immersion is the heat change arising from the replacement of the solid-gas interface with the solid-liquid interface when a solid surface is immersed in a liquid. Although immersion calorimetry has been established as a valuable and reliable means of determining solid surface properties such as wettability, it has seldom been applied in mineral processing research. In this study, precision solution calorimetry was employed to measure the enthalpies of immersion of different minerals in water. The enthalpies of immersion were then related to the first-order flotation rate constant as determined by the microflotation technique. The same measurements were also made on sulphide minerals whose surfaces were modified to different degrees of hydrophobicity using different percentage coverages of amyl xanthate collector. The enthalpy of immersion technique was capable of distinguishing and ranking minerals according to their wettability. All mineral types and collector-treated minerals conformed to the same relationship that was found between the enthalpy of immersion and the flotation rate constant. This conformed, empirically, to a power law equation. As the enthalpy of immersion decreased, there were large increases in flotation response for very small changes in hydrophobicity. In addition, a critical enthalpy of immersion (CEI) was found, above which no flotation could occur. The scatter in the data points could be corrected for by adjusting the rate constant using the density of the minerals to produce a robust relationship between the rate constant and enthalpy of immersion. These results have shown that the enthalpy of immersion is able to indicate both the natural mineral hydrophobicity and the extent to which collectors can render a mineral hydrophobic. This technique has considerable potential to be used as a sensitive and accurate measure of mineral surface wettability in order to predict flotation performance.

Jan 1, 2018

By G. K. Derby

The Bureau of Mines studied the problems caused by airborne contaminants from welding exhaust in surface mining operations and investigated equipment designed to reduce existing hazards. Four commercially available welding-fume exhaust units were tested to determine their effectiveness. Results indicated that the four units had the capability of controlling airborne particulate concentrations and bringing them to within allowable exposure limits.

Jan 1, 1981

By M. G. Fowler

A GENERAL decline in copper production for most American producers occurred during the past year as a result of shortage in available labor. Few noteworthy technical developments have been reported; undoubtedly, many changes and improvements have been made but have not been reported because of lack of time. During the war years through 1944 the pressure for sustained high production has been of prime importance and during 1945, with slackening of production, many operators were faced with the problem of catching up on repairs and maintenance of plants, with inadequate labor supply. In hydrometallurgy there were some important developments that undoubtedly will be reported during 1946. Several operators in the Southwest have instituted experimental leaching programs to exploit low-grade oxidized and mixed ore bodies. The Bureau of Mines is conducting pilot-plant experimental work to determine the possibility of producing a satisfactory sponge iron at an attractive cost from deposits of iron ore and coal in Arizona. The sponge iron would be used for the production of cement cop¬per. The cell house of the Inspiration Consolidated Copper Co. at Inspiration,

Jan 1, 1946

By Brian G. Thomas

Quality problems in continuous casting of steel can be identified as they occur by monitoring mold signals (level sensor, thermocouples in the mold walls, friction etc.) and taking appropriate action (such as slowing casting speed, changing taper, changing a clogged nozzle, or later visual inspection of the surface for possible downgrading. Surface depressions and groups of deep oscillation marks form at meniscus and reduce local heat transfer as they move down the mold at the casting speed. This slows shell growth, increases shell surface temperature, and causes characteristic dips in mold thermocouple signals. More importantly, they are also associated with longitudinal cracks. Characteristic thermocouple signatures have been identified for many defects, including sticker breakouts, transverse depressions and deep oscillation marks, narrow-face bleeds, transverse comer cracks, longitudinal cracks, mold level fluctuation defects, and other problems. With the help of computational models, these mold signals should be used to troubleshoot defects, and to take appropriate corrective action. Keywords: Continuous casting, defect detection, thermocouple signals, on-line control

Jan 1, 2003

By FLOYD T. TAYLOR

IN 1833, less than one hundred years ago, Michael Faraday discovered and stated the laws of electrolysis. His discovery formed the foundation of a new use of metals which has now reached a variety of application not ordinarily appreciated. Furthermore, things can be done with electro-deposited coatings which have thus far defied other methods. Some of the uses of electro-deposited coatings are interesting. The tonnage of metals already finding an outlet through such a channel is considerable. In general electro-deposits have two characteristics: ornament plus utility; utility plus ornament. Both these factors are usually found associated in electro- deposits. Ornament plus utility was probably the first use. For example, the silver-plating of tableware, having its real birth in Birmingham, England, about 1844. However, this same ornament plus utility retarded the development of electro-plating, because in the beginning, electro-plated articles were branded with the odium of imitation and shunned accordingly. The gold brick of the swindler may be an exception to this statement.

Jan 1, 1929

By Brinton C. Brown

This paper describes the methods and equipment developed at the Bureau's Experimental Oil-Shale mine near Rifle, Colo., for placing men in position to scale loose rock from the walls, pillars, and roofs of high stopes or rooms. The equipment developed at Rifle has application not only in oil-shale mining but in most of the country's underground limestone mines and in the exploitation of other mineral deposits mined in high stopes by room-and-pillar methods. Equipment in use at Rifle includes: 1. A boom-type scaling rig with a self-leveling platform constructed on a small "cat"-mounted crane. Men working from the platform on this machine can efficiently scale mine walls and roofs 27 feet above the floor. 2. A conventional fork-lift truck modified to provide a remotely controlled working platform from which men can scale to heights 27 feet above the mine floor. The platform on this unit is larger than on the boom-type rig and allows the men to inspect larger areas of the mine wall from a single setting of the machine. 3. A third rig, consisting essentially of a platform mounted on a tele-scoping tower, designed and built to elevate men 65 feet above the mine floor. Versatility of this machine permits men to work from the platform at heights of 5 to 65 feet. In the operating position, the unit requires a minimum clearance of 25 feet. In the nonoperating position the tower of the machine folds to an over-all height of 15 feet 10 inches to permit travel through haulageways. 4. An industrial gun, lightweight scaling bars, and mechanical scalers, which have been tried for removing loose rock from the mine walls with varying degrees of success.

Jan 1, 1950

By W. B. Paton

Introduction For several reasons the accident history of Flin Flon has been quite unlike that of any other mine in northern Canada, and very much unlike that of the average American metal mine. Towards the end of 1928, the mining project that is now Flin Flon, and that is now in the very: forefront of Canada's big producers was launched; but, metaphorically, it was launched in a tempest of mining troubles. Each branch of the mammoth enterprise was beset with extraordinary difficulties, and the Safety Department had its relative share. Difficulties in Accident Prevention The unusually rugged contour of the plant site made roads, and even moderately safe pathways, out of the immediate question. The project established an industrial outlet for depression-stricken areas which hitherto had been essentially agricultural; but through that outlet poured labour whose working atmosphere had been the bald prairie, labour that knew nothing of safety consciousness, labour that had to be moulded to industrialism, labour in the raw. A considerable length of the ore-body lay under the eastern section of Flin Flon lake. Open-pit methods were adopted to work the upper limits of the ore-body, and consequently the eastern section of the lake had to be dammed and pumped dry. The subsequent difficulties and hazards created by silt deposit cannot be fully visualized. And, finally, there was a geographical hindrance: the ore-body was partly in the Province of Manitoba and partly in the Province of Saskatchewan. The workmen's compensation problem became intricate. Insofar as accident prevention is concerned, Flin Flon's young industrial life may be conveniently divided into three distinct periods, namely: (a) Construction (Nov. 1928-June 1930) (b) Tuning up, and production till the strike (June 1930-June 1934) (c) Production from the strike till the present time At the peak of construction, due to the usual labour fluctuations of big jobs, there was a weekly turnover of about a hundred men. A very large percentage were Central Europeans, most of whom could neither read nor write English. Consequently, an organized safety programme was out of the question.

Jan 1, 1935

By E. C. Roper

THE Britannia Mining & Smelting Company, Limited, have been operating their property at Britannia Beach, B.C., continuously for nearly forty years and have mined over 33,000,000 tons of ore from orebodies within a belt of highly sheared rocks, five miles long by 2,000 feet wide. The property is in the Coast Range mountains, about twenty miles due north of Vancouver. The mountains rise abruptly from sea level to elevations of 4, 500 feet within a horizontal distance of 7,000 feet. The topography has enabled the orebodies to be developed by adit tunnels. The active mining levels are connected to the adits by incline and vertical service shafts. The main service adits are the 2200, 2700, and 4100 levels (see Figure 1). The mine surface shops, three bunk-houses, and over one hundred dwellings form the townsite camp at the portal of the 2200 level adit. A small camp of one bunk-house and a few dwellings is situated at the 2700 level portal. The beach surface shops and camp, adjacent to the 4100 level adit, service the mill, foundry, and other beach installations as well as the mining from the 4100 level. The ore mined from the various orebodies is delivered to the 4100 main haulage level through a system of rock raises and intermediate tramming levels and is hauled on the 4100 level to the mill.

Jan 1, 1945

By Diego Quiroz, Francisco Cuellar

Existen tareas esenciales como la exploración, inspección, y digitalización de galerías subterráneas que pueden presentar un alto riesgo para los trabajadores ya que se pueden producir accidentes. En este contexto, se hace necesario buscar soluciones más eficientes y seguras para la exploración, inspección, y digitalización de galerías subterráneas en la industria minera. Se propone como solución el uso de un robot terrestre no tripulado capaz de desplazarse en superficies irregulares para la digitalización, inspección, y diagnóstico recurrente y seguro de la infraestructura de galerías subterráneas en minería.

Sep 29, 2023

By A. R. Khodabandeh, T. Nematkhah

Correct selection of forging parameters is very important to produce sound superalloy parts. In this investigation nickel-iron base superalloy IN901 successfully forged and seal spacer, which is a part of airplane with about 11 kg weight has been produced. Forging has been performed on the basis of hot compression results, which show deformation above 1100°C associated with dynamic recrystallization (DRX) which can increase the workability of material. On the other hand annealing at 1100°C decreases the flow stress during hot compression, and then increases the material formability. Then billets annealed at 1100°C in electrical furnace for 24 hours and reheated again to 1100°C before forging. Initial square cross section billet with 128mm side and 202mm length forged immediately after reheating by 80MN mechanical press. Specimens forged in five steps: upsetting, three steps molding and finishing. Preformed and molded specimens reheated in electrical furnace before later step of forming. Finally specimens trimmed by 1 OMn mechanical press and hot set by hydraulic press and then cooled in air to room temperature. Results show that reheating temperatures has been selected correctly because there isn't any surface crack and die cavities filled completely by forging material. Material flow has been carried out properly and there isn't any defect in critical points especially in extradoses and intradoses. Microstructural examinations show that grain boundaries contain Ti-rich globular particles that formed during cooling.

Jan 1, 2006

By J J. L du Plessis, S Viviers, G Ratner

Escalating electricity costs are one of the biggest operational cost drivers in mining. The trend to use high-powered auxiliary fans delivering increased airflow to meet the dilution requirements of diesel equipment, together with the reliance on ducted systems rather than traditional flow-through systems to ventilate areas, increases the overall energy requirements of ventilation systems. To manage and reduce electricity costs energy management systems can be implemented, inefficient operating units can be replaced and the operation of energy-consuming components of ventilation systems can be optimised.This paper describes the process followed to design and develop an energy-efficient axial flow auxiliary fan. The fan-targeted design was based on static pressure and volume flow rate requirements incorporating higher overall fan efficiencies. A brief overview of the results is given, including the aerodynamic design procedure using computational fluid dynamic (CFD) analysis. The mechanical design criteria used, including stress analysis on the rotor and designs to improve the vibration levels of the fan, are also presented. Through this study it was demonstrated that the aerodynamically designed rotors using profiled and twisted blades improve the total fan efficiency considerably when compared with some of the older-generation fans using cambered plates. The latter were typical in the mining sector in South Africa at the time of the study where average overall fan efficiencies of standard cambered fans less than 63 per cent and some of the older-generation cast aluminium blades have peak overall fan efficiencies of about 65 per cent. Peak overall fan efficiency of more than 80 per cent was achieved by using the described design and development process. Additional benefits are that the fans are quieter due to the better aerodynamic design and have a longer operating life due to reduced vibration levels.In conclusion, the use of CFD to develop fans to deliver the required volume flow at the required pressure allows quicker design turnaround time. It furthermore allows the ventilation engineer the option to specify a specific fan and is not limited to an off-the-shelf catalogue fan. It thus allows engineers to purchase a fit-for-purpose energy-efficient fan. The introduction of reliable fan control systems may, however, still result in the biggest cost benefit for underground mines.CITATION:du Plessis, J J L, Ratner, G and Viviers, S, 2015. Design and development of energy-efficient secondary axial flow fans, in Proceedings The Australian Mine Ventilation Conference, pp 337–344 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By AIME AIME

CERTAINLY in point of attendance, and doubtless in several other ways as well, the 147th meeting of the A.I.M.E. was the best ever held. In times of depression, mining engineers and metallurgists have plenty of time to come to the Annual Meeting but money is scarce; at the height of industrial activity they have plenty of money but no time. "The current period of transition seemed to provide ideal conditions for' both the preparation of papers and attendance at their presentation. The weather made even the Californians present envious though the weather man gets no credit, for rain and snow was what he willed. Among the elevator men, the miners have the reputation of being the toughest crowd to handle, though the best natured, withal, of all the engineering groups that meet in the Engineering Societies Building. This year Your inquiring reporter was told, "it was the damnedest meeting I ever saw; they

Jan 1, 1937

Demand for primary aluminum ingot increased during February, and several producers temporarily suspended new bookings for ingot. Alcoa announced that it would restart a potline at its Warrick, IN aluminum smelter by April 1, 1979, increasing the operations of that plant to its full capacity of 290,000 tons per year. At the end of February, it was reported that Alcoa would reactivate two of the seven units at its idle Point Comfort, TX smelter in May 1979, increasing the company's annual capacity by about 60,000 tons.

Jan 1, 1979

By B. M. Thethwayo

Graphite blocks are currently used in the concentrate - slag zone in primary PGM smelters, and can possibly be extended to the matte zone. This project evaluates the interaction between synthetic matte and graphite blocks on a laboratory scale. Static crucible tests were performed where graphite crucibles (prepared from standard and high-grade graphite) were filled with synthetic matte (27.7 per cent S ? 46.1 per cent Fe ? 17.0 per cent Ni ? 9.2 per cent Cu) and heated to 1550°C for different time periods (1?5 days). Matte penetration was evaluated using a SEM, while graphite dissolution was evaluated by measuring the carbon content of the matte with a LECO carbon analyser. Matte penetrated into standard grade graphite up to approximately 2 mm, while matte infiltration into the high grade graphite was limited to the immediate hot face. The saturation solubility of graphite in the synthetic matte at 1550°C was 0.43 per cent. Copper, iron, nickel, and sulphur were detected in an accretion that formed in the water-cooled part of the furnace. This accretion consists of mainly Cu-S and Cu-Fe-S based phases.

Jan 1, 2012

By JUAN DIAZ, Kray Luxbacher, Steven Schafrik, Dionissios T. Hristopulos, Zach Agioutantis

Methane gas is emitted during both underground and surface coal mining. Underground coal mines need to monitor methane gas emissions to ensure adequate ventilation is provided to guarantee that methane concentrations remain low under different production and environmental conditions. Prediction of methane concentrations in underground mines can also contribute towards the successful management of methane gas emissions. The main objective of this research is to develop a forecasting methodology for methane gas emissions based on time series analysis. Methane time series data were retrieved from atmospheric monitoring systems (AMS) of three underground coal mines in the USA. The AMS data were stored and pre-processed using an Atmospheric Monitoring Analysis and Database Management system. Furthermore, different statistical dependence measures such as cross-correlation, autocorrelation, cross-covariance, and variograms were implemented to investigate the potential autocorrelations of methane gas as well as its association with auxiliary variables (barometric pressure and coal production). The autoregressive integrated moving average (ARIMA) time series model which is based on auto-correlations of the methane gas is investigated. It is established that ARIMA used in the one-step-ahead forecasting mode provides accurate estimates that match the direction (increase/decrease) of the methane gas emission data.

Aug 2, 2022

By Phil Wilkinson, Sam Whitaker

"The installation of large (XL) diameter monopiles offshore typically requires expensive and specialist plant, equipment and vessels. Due to the increasing size (weight, diameter and length) of the foundations, in order to mitigate installation risk, the use of large diameter drills is becoming an increasing requirement.Project developers often try to avoid drilling operations due to the time associated with the drilling process. This restricts projects in terms of location and it also overlooks the additional engineering benefits drilling can bring to monopile foundation design e.g. reduced foundation material and better fatigue design life.By comparing the lessons learned of three milestone overwater drilling projects; methods of maximising drill speed and decreasing drilling process time is established. Particular emphasis is put on pile internal relief drilling in a process known as Drive-Drill-Drive (DDD).The milestone overwater drilling projects are North Hoyle Offshore Wind Farm (OWF) (2003); Flamanville EPR cooling water outlet shaft (2008); and Gwynt-y-Mor OWF (2014).By evaluating the effect of foundation pile diameter on drilling process times, example foundation installation costs are derived and used to show that incorporating drilling as part of a process may not be cost prohibitive to projectsContinued advances in drill technology, and drilling rates of penetration, combined with an integrated approach to foundation design, challenge whether hammering only is always the optimal solution for XL monopile installation."

Jan 1, 2017