Search Documents

By John Anthony Vasquez

During the last years Riva Acciaio Verona has taken the decision to invest in the route of a fully automated meltshop. The aim is to reduce at the minimum the operator's intervention from the bucket preparation till the ladle transfer to the continuous casting bay. The foundation for achieving the goal is the introduction of innovative technological solutions (fully automated cranes for bucket charge in the EAF, robots for sampling, etc. The paper underlines how the different solutions are based on the best practices to improve operator's safety and describes the different steps of the project, the different solutions adopted and the results in terms of production, energy savings, cost reduction and improved safety. Details are presented for: scrap yard management and bucket preparation, EAFs centralized controls and related robots for auxiliary operations (sampling, EBT cleaning, scraper for slag door automation, complete mass & energy balance based on process control), LFs centralized controls and process integration.

Aug 16, 2017

By J. A. Cavallaro

The heats of formation of anhydrous barium carbonate (witherite), strontium carbonate (strontianite), and lead carbonate (cerussite) were determined by solution calorimetry. The solution mediums were hydrochloric acid for barium and strontium carbonates and perchloric acid for lead carbonate. The heats of formation at 298.15° K are as follows: BaCO3 -297.5 ± 0.8 kcal/mole; SrCO3 -294.6 ± 0.5 kcal/mole; and PbCO3 -168.0 ± 0.3 kcal/mole.

Jan 1, 1966

By Johann Steynberg

The design and construction of a Concentrator based on initial pilot plant work is rarely perfect. Palabora's plant was no exception although the basic objective to produce copper in a safely conservative manner was certainly achieved in a profitable manner. identification of the metallurgical and mechanical deficiencies of the plant through operating experience and a better concept of the minerology of the orebody enabled the development of a more efficient process both in terms of the metallurgical performance and cost effectiveness. To maintain and improve this level of efficiency, continuous inspection and revision of the plant metallurgy and engineering standards is required. In this presentation a few of the investigations and changes are described: 1.0 Alternative methods to restrict and eliminate the detrimental effect of critical size material on the performance of an autogenous mill. 2.0 An analysis of the environmental condi¬tions in Palabora's grinding circuit and the introduction of high chrome balls as grinding media. 3.0 The role of magnetite in the beneficiation process at Palabora. 1.0 Alternative methods to restrict and eliminate the detrimental effect of critical size material on the performance of an autogenous mill.

Jan 1, 1985

By Lewis A. Smith

This circular presents a summary of the domestic chromium industry, and discusses the salient features of the world situation , reflecting the literature of the subject . The United States Bureau of Mines has in its files additional detailed information on many subjects briefly discussed in this paper and desires to assist the industries and the public by giving further data in response to individual inquiries . It will welcome comment and criticism and any contributions that would assist in making future editions of this circular more accurate . Unlike most common metals , chromium is rarely marketed as a pure metal . The chromium industry deals mainly with chromite , the principal ore of chromium , and with ferrochromium , the basic alloy in which chromium enters the metallurgical industry.

Apr 1, 1932

By Mario Samamé Boggio

El presente trabajo describe el período de la Colonia dentro de la historia minera peruana. Dentro de esta época no se utilizó método alguno para su explotación y no hubo un adecuado manejo de recursos y energías. Posteriormente se describe la mita, expansión (Huancavelica, Huantajaya, Laicacota, Hualyacoc), así como se describe las minas de plata, oro, metalurgia colonial y la misión Nordenflicht.

Sep 1, 1983

By M. E. Hawkins

Mineral analyses and electrical resistivity measurements of 324 representative samples of oilfield brines from 24 oil-productive counties in Mississippi and Alabama are presented in tabular form. Results of the mineral analyses, which include calcium, magnesium, carbonates, bicarbonates, sulfates, chlorides, sodium, and barium (with strontium if present), are reported in milligrams per liter. Electrical resistivity measurements in ohm-meter2 per meter at 75° F are reported in ohm-meters in the tables. Chemical analyses of formation waters are helpful to operators having water problems associated with petroleum recovery; electrical resistivity values are helpful in making interpretations from electric logs.

Jan 1, 1963

By Lyle F. Smith

With the demand for larger diameter raises under all ground conditions and the increasing price of drill rods and operating costs, it was evident that there was a need for a raise borer with a variable-speed drive and fast-response torque limiting control. The raise boring machine described in this paper was developed after several years of market research and discussions with mine operators and construction contractors. This paper discusses the Ingersoll-Rand raise borers with the solid-state controlled DC motor drives. These machines have gained wide acceptance in the five-year period since being placed in operation and are designed to accommodate the range of raise diameters and lengths most required today.

Jan 1, 1978

By S. Haggarty, R. Walton

Barrick's growth and development plan will add three major new mines during 2005 including the Lagunas Norte Project in the La Libertad Province of Peru, the Veladero Project in the San Juan province of Argentina, and the Tulawaka Mine in north¬western Tanzania. Lagunas Norte and Veladero are similar in that they are both green-field open pit deposits at elevations over 4,000 meters above sea level, with two stage crushing and heap leaching followed by Merrill Crowe zinc precipitation for precious metal recovery. Operating sites will each generate in excess of 700,000 ozs Au per annum with commissioning and full scale operation planned during the third and fourth quarter of 2005. Details with regards to regional geography, development schedule, production and process specifics for Lagunas Norte and Veladero will be discussed in this presentation providing an overview for the respective properties.

Jan 1, 2005

By Patricio Berrios, David Barriga, Peter Amelunxen, Gerson Sandoval, Roger Amelunxen

Laboratory test equipment and methods have undergone relatively little change since their introduction in the 1950’s. The Denver sub-A cell is still by far the most commonly used laboratory batch cell, but bottom-driven and instrumented cells are beginning to appear. Test procedures have also changed little over the past 60 years, and most engineers continue to rely on empirical models for predicted plant scale performance from laboratory scale tests. This approach is problematic, because changes in the froth phase characteristics in the lab hamper the reliability and reproducibility of the empirical extrapolation to plant scale. In a previous work, the authors reported on the impact of froth recovery at the laboratory cell, showing that variability in the froth recovery can lead to significant error in the modeled kinetic rate constant unless it is properly accounted for in the scale-up model. In this work, we review the role of hydraulic entrainment in the lab cell, and how variability in particle specific gravity, shape factor, and froth residence time can impact the entrainment recovery.

Jan 1, 2014

By Saurav Kumar, Akshay Kumar, Vinayaka R. Kiragi, M. K. Banerjee, Amar Patnaik, Vinod Kumar

Today’s industrial technology offers to optimize and reutilize the resources available in terms of scum that remains after hot rolling in steel rerolling mills in Rajasthan, India. Vast reserves of low-grade coal exist and tons of mill scale are produced everyday after hot rolling in steel rerolling mills in Rajasthan, India. The present research work aimed to optimize the various parameters of solid-state reduction of mill scale using low-grade coal from Rajasthan, India. This study investigates the effect of reduction temperature (850–950 °C in steps of 50 °C), reduction time (60 to 180 min, in step of 60 min), mill scale size (800– 300 μm), and mill scale to coal ratio (1:1, 1:2 and 1:3) on achievable metallic iron percentage and its metallization. A higher percentage of iron content is obtained at a lower particle size of 300 μm. The structural analysis is carried out on 300 μm mill scales using XRD analysis, which shows the percentage of iron is approximately 63%, and metallization above 80% can be obtained under the reduction temperature at 900 °C for 180 min, for 1:3 ratio (mill scale to coal ratio). The chemical composition of the mill scale is obtained using X-ray fluorescence (XRF), and particle sizes as well as distribution of mill scale are determined by scanning electron microscopy (SEM). The elements present in the mill scale are also verified using EDS, which indicates the presence of a major portion of Fe, followed by Fe2O3, Si, and C, respectively.

Aug 14, 2020

By Darrin Wikoff

"The data, compiled by the Department of Energy (DOE), indicates that the average industrial plant could reduce its total energy cost by 14.8% by implementing effective Life Cycle Asset Management processes. The actual savings varies by industrial classification, but in all cases the potential is substantial and could have a marked impact on the operating profit of the company.Improvements geared towards improving equipment reliability have distinctive linkages to environmental performance, such as reducing the amount of product and raw material waste through routine monitoring of system parameters through predictive technologies, and preventing interruptions to production cycles with a focus on Overall Equipment Effectiveness (OEE).Alcoa successfully reduced solvent disposal costs by more than 40% and GE reduced greenhouse gas emissions by more than 250,000 metric tons. This presentation will show you how companies have successfully reduced energy and disposal costs through a focused effort on manufacturing process reliability.IntroductionSmelter in the ParkThe quaint town of Portland, Victoria protrudes outward towards Antarctica from Australia’s southeastern coastline. Portland is a quiet rural community surrounded by agriculture that draws tourists by the thousands to the southernmost edge of Victoria by way of breathtaking cliff top views of the majestic Southern Ocean, the intrigue of shipwreck coves along the Great Ocean Road, and what most will call the eighth wonder of the modern world, the “Smelter in the Park”. Integrated within Portland’s beautiful landscape is a 356,000 ton/year aluminum smelter that stands as a symbol of collaboration between nature and industry. Nestled atop a ridge which faces “Sail Rock”, a popular destination of local and visiting fisherman, the smelter is engulfed in a mix of brush and wetland preserves that are home to many of Australia’s feathered and fourlegged natives. Also within its interior you’ll find parks and natural landscapes abundant where man and machines coexist with the native inhabitants."

Jan 1, 2009

By X. -G. Chen, J. Qin, K. Liu, D. Racine

"Understanding the thermo-mechanical fatigue (TMF) behavior of materials plays a significant role in the safety design of critical components used in aerospace and automotive industries, such as engine blocks and cylinder heads, which undergo the cyclic change of temperature and stress. However, the cyclic changes of temperature, stress and strain make it difficult using the traditional testing methods to accurately simulate the TMF process. In the present work, the Gleeble® 3800 system was successfully applied to develop a reliable procedure to measure the TMF behavior of aluminum alloys. The modified setup together with the new designed program allows the Gleeble system to precisely simulate the cyclic profiles of temperature and mechanical strain. The novel procedure includes the calibration and verification of the TMF setup to ensure the test validity with Young’s modulus measurement, multi-cycle measurement of the thermal strain and zero stress adjustment followed by online monitoring the TMF cycles. The results of the TMF testing of an AA6061 alloy under cyclic temperatures (60–300°C) and various strain amplitudes (0.2–0.6%) were demonstrated. Its TMF behavior was characterized by the typical hysteresis loops and cyclic stress-strain response.INTRODUCTION The thermo-mechanical fatigue (TMF) behaviour becomes increasing important to evaluate the elevated-temperature properties of materials used as the critical components in automotive and aerospace industries, such as the gas turbines (Hu, Shi & Yang, 2016; Moverare, 2007; Segersäll et al., 2015) and engine blocks (Grieb, Christ & Plege, 2010; Javidani & Larouche, 2014). During the cycles of start-up and shutdown of the engines, these components undergo a complex change of loading. Meanwhile, a dramatic temperature gradient exists on the components due to the cooling system. Therefore, the cyclic changes of load and temperature can give rise to the TMF and may limit the use life of such components (Hu, Shi & Yang, 2016; Javidani & Larouche, 2014; Moverare, 2007). Hence, performing the TMF tests to precisely simulate the cyclic changes of load and temperature to understand the TMF behaviours of materials is playing a significant role in the safety design of these components. For TMF tests, two principal types of cycles are generally employed, including the in-phase (IP) cycle where the load and temperature are at the same phase (i.e. maximum load at highest temperature) and out-of-phase (OP) cycle where the maximum load is applied at minimum temperature (Kliemt, 2012; Miller, 2014). The most significant damage mechanisms in engine components are reported to be OP TMF cycles (Javidani & Larouche, 2014; Kliemt, 2012)."

Jan 1, 2018

By L. Zhou, L. Yuan, R. A. Thomas, D. Bahrami

The abstract emphasizes the importance of a calibrated ventilation network model for mine ventilation planning, optimization, and fire simulation. It highlights the impact of continuous airflow monitoring on improving model calibration. The paper discusses an experimental study at the Safety Research Coal Mine (SRCM) to understand the use of continuous airflow data for model improvement. It also addresses practical problems in calibration and tuning using this data, including analysis of air velocity sensor fluctuations and application of sensor location correction factors for accurate average air velocity.

Mar 7, 2022

By S. D. Tolgyesi

Kidd Creek Background ? Located in Northern Ontario, Canada ? Underground base metal mine ? Operating since 1966 ? Total of 125Mt mined to date (2.43% Cu, 6.60% Zn) ? Current plan at 2.4Mt/Y (6575t/D) Current Practices ? Evaluating stope margins to ensure that value is added ? Scheduling sulphide and Cu stringer ore to limit oxidation in passes ? Scheduling to maintain uniform grades to concentrator ? (SOPs highlight problem stopes on mine plans, and limit blast sizes in those stopes which may contain sulphides prone to oxidation) ? Scheduling high-Pb stopes to avoid spikes to concentrator ? Providing weekly, monthly and long-term forecasts ? Reconciling mine and mill production ? Underground grade and dilution estimates by mine supervision ? Terminate mucking when grade becomes sub-economic ? Laser cavity surveys to provide feedback and improve Designs Cut-off Grades ? Ore value is obtained from copper, zinc and silver ? Ore outlines at 2% copper equivalent used to guide stope planning; sulphide outlines obtained from contacts while copper stringer outlines drawn from block model (kriged) ? Datamine block model and CADD software used to evaluate alternative stope shapes ? Stopes classified as waste, incremental, or full-cost based on margin calculations for each stope ? Incremental ore may be mined if it does not displace fullcost Ore Conclusions ? Grade control remains an important function for optimizing the ore extraction at Kidd ? The scope of the function has changed to a scheduling focus ? A change in grade control practices over time has not led to significant changes in concentrator feed ? The lead and iron sulphide content of the ore display upwards trends and may require more attention in the future ? The key function of field observations has shifted to flagging exceptions and terminate mucking at grade cut-off

May 1, 2003

By A. Varma

Successful technology commercialization occurs when a company is focused on creating shareholder value by providing a reliable product at a price point attractive to the market, while at the same time maintaining strict control of its internal cash burn rates. Developing a technology platform and a market platform are equally important in the commercialization of new technologies such as fuel cells. This paper will discuss some of the key barriers that may prevent successful market entry for emerging and disruptive technologies, such as: R&D priorities, supply chain / manufacturing issues, materials, cost reduction strategies, customer needs, developing a market pull strategy, institutional barriers such as existing regulatory/approvals processes and/or current design/purchasing practices, product reliability and resilience, and finding the right path to market. SDTC is an arms length foundation that aims to financially support the successful market entry of emerging and disruptive technologies that can provide significant environmental benefits to Canada. The fuel cell industry, which represents one such technology, is at a critical point in its evolution where market receptivity and the technology platform are converging to potentially create significant customer advantages for fuel cell products being developed today. Since its inception in 2001, SDTC has received over 850 business cases from which it has identified successful strategies to overcome the noted barriers to commercialization. While maintaining commercial confidentiality, the SDTC database will be mined to: Identify specific success stories that have overcome various barriers and discuss their strategy; Identify specific fuel cell related industry experiences that hinder successful market uptake. The general attributes and trends of successful technology developments identified in this paper will hopefully provide guidance to technology developers and prepare them to successfully tackle the next set of hurdles on the path to commercializing their technology, once they have proven their technology works in the laboratory.

Jan 1, 2005

By B Crowdey, J Wall

The particular underground operation relating to this paper is a gold producer and has an orebody predominately consisting of rhyolite and marcasites pyrite. The ore has been identified as being reactive to nitrates.Operations currently utilise two twin boom Tamrock™ Super-Drill Jumbos for development mining. Capital (waste) headings have a nominal size of 7 m wide × 6 m high, while ore headings are designed at 5 m wide × 5 m high, with the lower reaches of the mine narrowing down to a 4.5 m × 5 m design. Production drilling is currently undertaken with an Atlas-Copco L6 Solo. Due to the reactivity of the ore, inhibited emulsion phase bulk explosives are used for all blasting activities, with electronic detonators utilised in the production sequence.Sublevel shrinkage stoping is utilised when the orebody is stronger than the host rock. After blasting the ore, and during extraction, the surrounding host rock cannot maintain integrity and it ‘collapses’ on top of the ore. Gravity forces this collapsing rock to follow the blasted ore through the drawpoints.The highest risk involved with sublevel shrinkage stoping is the necessity for charge crews to work upon ‘rills’ at the drawpoints, which are occasionally unstable, to charge the next blast ring to be fired. To overcome this issue a loading technique called ‘precharging’ is used whereby two to three rings are charged, but only the first ring is fired. This technique can minimise risks by taking the charge crew away from the rill and brow.As this mine contains hot and reactive ground, strict guidelines from the Australian Explosives Industry and Safety Group Inc (AEISG) are adhered to. These guidelines relate to the sleep time for the precharged rings.This paper describes the issues faced with precharging in hot and reactive ground, the monitoring required and the systems and procedures that were put in place to enable a successful outcome.CITATION:Crowdey, B and Wall, J, 2014. Precharging sublevel shrinkage production rings in hot and reactive ground with electronic blasting systems, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 283–288 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By Arthur W. Cooper

This paper contains a review of the development of blast furnace? slag handling and processing technology in the Ironmaking industry over the past 30 years, with an emphasis on economic and environmental factors. The requirements and practice of air-cooling slag for use as aggregate and of pelletizing and granulating slag for use in cement manufacture are described. The operation of slag pits, slag pots or ladles, the slag pelletizer and early granulation systems are compared with the new continuous .granulation, dewatering and handling systems developed in the past decade.

Jan 1, 1992

By Sara J. Davenport

With the increased demand for mercury incident to preparations for national defense and the reduction in imports from some of the usual sources owing to war conditions, many small mines in the United States Pure now being worked that ordinarily would be unprofitable. This is indicated by the following table on mercury produced in the Unite States in 1939-40 (1)4/

Jan 1, 1941

By D D. Deacon

A brief description is given of the requirements which No. 4 Shaft has been designed to meet and of the methods by which two-stage winding of rock has been accommodated in a single shaft sunk to a depth of 7,421 ft. This is followed by a consideration of the factors which led to the decision to sink the shaft as rapidly as possible. Introduction T HE No. 4 Shaft of Hartebeest-fontein Gold Mining Company, Ltd., has been sited to serve the deep southern area of the mine, some 1,500 claims in extent, between the elevations of 6,250 and 7,300 ft. below surface. From this area, some two-thirds of the mine production will ultimately be obtained. Above the 6,-250-ft. elevation, an existing shaft hoisting system, situated adjacent to the reduction plant, is of adequate capacity to cater for all ore hoisted to surface for milling. No. 4 Shaft will therefore be required to provide downcast ventilation of 1,000,000 c.f.m., together with surface hoisting facilities for men, material and development rock and underground hoisting

Jan 1, 1965

By P. Somasundaran

Treatment of mineral surfaces with appropriate surfactants plays an important role in mineral processing operations such as flotation, flocculation and dewatering. Recently biosurfactants, in particular, have received a considerable amount of attention because of their unique surface active properties and biodegradability. In this work we examined the performance of biosurfactants, sugar based alkyl glycosides and sophorolipid esters as reagents to control the hydrophobicity of minerals with selectivity of adsorption on mineral surfaces for flotation applications. It was discovered that n-dodecyl-ß-D-maltoside adsorbs on alumina, titania and hematite but, interestingly, not on silica. The hydrophobicity obtained is governed both by the surface coverage as well as the nanostructure of the adsorbed layer in terms of orientation of the adsorbed species. Surprisingly, even though the above surfactants are non-ionic, their adsorption was pH-dependent. We have correlated this pH dependence to the type of species on the mineral surface. Also it is shown that mixing of these surfactants with traditional ones can help reduce the carbon footprint due to synergy between the reagents and help selectivity due to antagonism. The experimental results were analyzed to get information on optimal pH and dosage conditions, for mineral surface modification. The study provides guidance for mineral treatments using biosurfactants and the potential use of these next generation reagents in mineral processing.

Jan 1, 2014