Search Documents

By C Rothfuss, X Wang, S J. Herbert, K Prasad

The extraction of groundwater to produce gas from coal seam gas (CSG) reservoirs has highlighted the opportunity for beneficial uses of groundwater in Australia. This paper presents an assessment of alternate groundwater modelling approaches that can be used for assessment of one beneficial use option, that of injection. This assessment examines the outcome of the use of different simulation methods on predictions of hydrodynamic behaviour.In this paper, a simplified hydraulic concept of a multi-aquifer system within the hypothetical injection field was used to investigate the hydrodynamic behaviour of injection into the Precipice Sandstone. Comparisons were made through the analysis of a Theis 3D analytical solution with 2D and 3D numerical solutions. The paper discusses the different solution methods and the impact of these on predictions of pressure and flux. Differences in 2D and 3D solutions result in implications if planning injection as a beneficial use of water. For example, the 2D solution resulted in faster and higher injection pressure build-up when compared to the 3D solutions. The 2D modelling could result in either plans that require higher capital expenditure for a greater number of wells in order to spread the pressure effect and remain below the maximum injection pressure or a reduced injection rate. Meanwhile, the 3D modelling with sensitivity analysis could result in planning for lower capital expenditure for fewer wells required to spread the pressure effect and remain below the maximum injection pressure. CITATION:Wang, X, Herbert, S J,?Rothfuss, C and Prasad, K, 2013. Assessment of effectiveness of artificial recharge for coal seam gas water management based on numerical modelling, in Proceedings Water in Mining 2013 , pp 67-72 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By V. Buddhiraju

Liberation of valuable minerals from low-grade ores is an important challenge faced by the minerals industry. It is necessary to grind the ore to extremely fine size in order to liberate the mineral from such ores. As it is generally difficult to produce ultra-fine particles of diameter less than 1-10 mm using traditional grinding equipment such as the ball mill and the rod mill, several new types of grinding equipment are being explored to produce ultra-fine particles. The planetary ball mill is promising in that it makes grinding to submicron sizes possible by imparting high energy to the ground powder. It consists of four pots mounted on a disc. The pots and the disc rotate in opposite directions. The high-speed rotation of the pots and the disc makes the grinding media move at high centrifugal velocities leading to high impact energy and thus improving the grinding performance. The planetary mill is currently being explored for its capability to produce ultra-fine particles on a large scale. In this context, there is a need to understand the dynamics of the ultra-fine grinding process within the planetary ball mill. Here, we address this need by studying the movement of media inside the pots and the grinding kinetics, employing both experimental and modeling techniques. The experiments were conducted on a laboratory scale planetary ball mill. The particle size distribution of the powder was monitored to allow an estimate of the grinding kinetics to be made while video images of the media profiles inside the pots were taken to allow quantification of the media movement as a function of process variables such as the media size, percent loading, etc. The population balance modeling (PBM) framework was used to simulate the kinetics of grinding while the discrete element modeling (DEM) approach was utilized to simulate the media motion. The parameters in the population balance model, namely, the specific breakage rate and the breakage distribution function were determined by fitting the batch grinding equation to the experimental data. The predicted powder size distributions were found to be in good agreement with the experimental data. The experimental results have shown that the mean size of product powder decreases as the size of the grinding media decreases. Keywords: population balance modeling, grinding, planetary mill, grinding media, grinding equation

Sep 1, 2012

By W. F. McDermott

This paper covers the development, construction and operation of a 53-mile slurry pipeline operating in Tasmania, Australia. Special development techniques are discussed, as well as the operation of this line and its impact on transportation from remote areas.

Jan 1, 1970

By Sheshang Singh Chandel, Prvan Kumar Katiyar, Navneet Singh Randhawa, Prince Kumar Singh

Mineral process wastes, such as metallurgical slags nowadays, are of significant metals and materials resources in the circular economy. The usability of iron-making slag is well established; however, steel slag still needs to be utilized due to various physicochemical constraints. In this context, we have reviewed the global steel slag generation, processing, characteristics, and potential application with suggestions for futuristic possibilities to address the technical, economic, and environmental aspects of steel slag recycling. The steel slags inherit characteristics from ore chemistry and their processing routes, which may be Blast Furnace-Basic Oxygen Furnace (BF-BOF) or Direct Reduced Iron-Electric Arc Furnace (DRI-EAF) steel-making routes with/without treatment in a Ladle Furnace (LF). The average generation of slags in BOF, EAF, and LF processes accounts for 110 kg, 70 kg, and 40 kg per tonne of steel, respectively. Considering global steel production of 1878 million tonnes in 2020, the associated slag by-products possess a significant resource of major components like FeO, CaO, SiO2, Al2O3, etc. Selecting a recycling technique depends on the slag's end use, logistics, and physicochemical characteristics. BOF and EAF slag are used ~ 48% in road construction applications and ~ 10% for industrial specific metallurgical use. EAF slag is preferred as cementitious material as compared to BOF. Hot-stage modification of BOF slag has emerged as a preferred method to achieve desired chemical and subsequent mechanical properties for end use. BOF slag has high carbon dioxide sequestration potential for in-plant remediation among steel slags.

Nov 20, 2023

By G. R. Hopkins

According to the annual refinery-capacity survey of the Bureau of Mines, the number of refineries in the United States showed little change in 1940, increasing from 057 the first of the year to 562 at the close. Although a number of plants were dismantled in Texas and other States, more than compensating gains were made in California, Illinois, and other States. Low gasoline prices, competition for crude-oil supplies, particularly in Illinois, and the termination of a favorable distributing arrangement for independent plants in the Los Angeles area, forced about 50 refineries to close down in 1940. The number of operating plants accordingly declined from 461 on January 1, 1940 to 420 on January 1, 1941 and the number of idle plants increased from 86 to 136 in the same period. These developments were also reflected in the capacity data, the operating capacity declining from 4,196,694 barrels daily on January 1, 1940 to 4,180,588 daily on January I, 1941 and the idle capacity rising from 431,952 barrels to 53g8381 barrels in the same period. However, the completed capacity on January 1, 1941 (4,718,969 barrels daily) was 2 percent above the previous year.

Jan 1, 1941

By H. W. J. P. Neomagus, R. K. K. Mbaya, J. R. Bunt, N. T. Leokaoke, N. W. Makgobelele

Silicon Smelters consumes more than 80000 t/a of wood-derived charcoal as carbonaceous reductant in the production of silicon metal. More than 10% of this material is discarded as fines (<6 mm) generated due to abrasion during processing. Charcoal fine residues (<650 μm) and polyvinyl alcohol (PVA) binder were used in this study to produce mechanically strong charcoal briquettes for metallurgical application as carbonaceous reductant. The PVA binder was added in mass percentages of 1, 3, and 5 wt% to the charcoal fines. The compressive strength, abrasion resistance index (ARI), drop shatter resistance (SRI), and water resistance index (WRI) were measured as functions of curing for up to 7 days under atmospheric conditions, and the results compared with metallurgical grade coarse charcoal. The ash content of the produced briquettes was found to be high (6.6–8.0%) compared with the coarse charcoal (1–3%). The 3 and 5 wt% PVA-bound briquettes were found to be the strongest, with compressive strengths of 40 and 115 kg/cm2 respectively, with WRI values of 75 and 73% respectively. The produced briquettes were found to have lower ARI and SRI values compared to the coarse charcoal. Future work should include beneficiation of the fine charcoal discards prior to briquetting, and an increase in binder addition to above 6 wt% to improve the ARI and SRIn.

May 1, 2021

By Marvin E. Lane

Viburnum, located in the foothills of the Ozarks in south-east Missouri, is the site of a modern lead mining and milling operation. Two mines are currently producing a total of 5,000 tons per day and a third mine is in the final development stage, with full production scheduled for late this year (1964). These mines will supply the tonnage required to keep the Viburnum mill operating at a full capacity of 7,000 tons per day for many years. The efficient underground mining operation is completely trackless. Drill jumbos are used to break the ore in a room and pillar method of mining. Transloaders, or St. Joe shovels, and trucks do the loading and hauling. The Viburnum mill has a world-wide reputation as a most efficient operation. This is due to the extensive use of automatic process controls, and labour saving materials handling facilities. Introduction THE St. Joseph Lead Co., has operated lead mines in southeast Missouri for 100 years. These operations have been confined largely to the area called the

Jan 1, 1964

By Pei‑liang Xu, Jun Wang, Xi Zhang, Deng‑pan Qiao, Tian‑yu Yang

The surface backfill, serving as the operational platform for continuing mining in upward slicing and filling stopes, is required to possess sufficient strength and thickness. Currently, there are limited model methods for determining the strength and thickness of the surface fill body. By analyzing the mechanical actions on the surface backfill, it is determined that its stability is mainly influenced by the combined effects of normal and tangential uniform loads under full-load conditions of trackless equipment. Assuming a circular contact surface between the tire of the trackless equipment and the surface backfill, and utilizing solutions from elastic mechanics theories such as the Boussinesq and Cerruti solution, the stress and displacement distribution of the surface fill body were obtained. Based on the maximum vertical stress condition, where the surface backfill body undergoes maximum deformation while still in an elastic state, and considering the stress–strain relationship, a model for the strength and thickness of the surface backfill has been established. According to the research findings, the design for the strength and structural parameters of the surface backfill has been developed to meet the full-load operation of the Atlas ST7 scooptram, with a compressive strength of 1.32 MPa and a thickness of 0.5 m. Numerical simulation analysis results indicate that the stress and displacement of the surface backfill align with theoretical analysis results. Practical results from industrial application in the western section of the Dahongshan Copper Mine demonstrate that the designed strength and thickness of the surface backfill meet the operational requirements for trackless equipment, resulting in significant engineering application effects and economic benefits. The research findings hold significant importance for advancing the theory of backfill mining and have high applicability and promotional value for similar mines.

Mar 24, 2024

Coal mining legislation makes frequent reference to æSafety Management SystemsÆ but there is a chronic shortage of useful guidance material as to how these might be applied to hazardous exposures. Several studies have indicated that for each death that is reported as a result of an industrial æaccidentÆ, there are five deaths that caused by occupational exposures. Because the deaths from occupational exposures do not occur on site and often well after employment has ceased, they are generally unreported. Improved access to mortality data from coroners, the Australian Institute of Health and Welfare and superannuation service providers (early claims from death and total permanent disability), has given rise to some analysis of death and disability data that provides evidence that there are emerging opportunities to develop and improve safety management systems for hazardous occupational exposures. Issues explored include how safety management systems might be developed in relation to dusts and chemicals and other hazardous exposures to ensure the risk of disorders with long latency periods are reliably assessed and the exposures effectively managed. The current standards and guidelines which refer to safety management systems in general or to management of exposure related hazards are examined. Many standards are based on dose-response studies that provide for an acceptable percentage of workers to suffer adverse health outcomes. An alternative management system might be to apply dose-response relations to health surveillance to identify æat riskÆ individuals and effectively manage health and related safety risk at an early stage.

Jan 1, 2005

By H. Golzarpoor

Life Cycle Analysis (LCA) is a methodology for evaluating the environmental impacts associated with a product during its life cycle. LCA is identified as the most reliable method for verifying environmental impacts; however, current LCA-based approaches have certain limitations for environmental analysis of construction products. Integration of the LCA methodology with Discrete Event Simulation (DES) provides a sound framework for modeling and analysing the environmental impacts of construction products. LCA and DES is one possible combination for analysing the cause and effect of various scenarios where time, resources, and randomness of input variables affect the outcome and, therefore, has the potential to address the shortcomings of LCA in construction. Recent studies in disciplines other than construction such as manufacturing systems have revealed positive effects on evaluation of environmental metrics while integrating LCA with DES; however, this integration has not yet been applied for environmental analysis of construction products. By implementing LCA data in a DES model, this research proposes an environmental model of earthmoving operations in a case study. Environmental variables are simultaneously assessed with production variables in the same simulation model and the integration of DES and LCA is discussed.

Aug 1, 2013

By Gene Mattila, Ron Boyd

Introduction Rock bolting is a general term that encompasses pinning, roof bolting, rib bolting, and cable bolting. Rock bolting contributes the highest nonproductive cost and is the most significant safety risk in mining today. Total installed bolt costs are now more than $20 per bolt. Rebolting or repair work doubles this. And bolting accidents account for about 30% of all fatal and nonfatal lost time accidents. It is only logical, then, for the mine operator to install the highest quality anchors possible. Every bolt on the market - tensioned, untensioned, full contact, or point anchor - has designed capabilities in axial, shear, and fluctuating ground conditions. Bolts will provide a designed support if material specifications and installation procedures fall within the manufacturer&apos;s recommendations. This also assumes that there are no unexpected geological or operational changes. Proper material specifications and installation procedures should guarantee the mine operator a quality anchor. To help assure this, the Mine Safety and Health Administration (MSHA), the US Bureau of Mines (USBM), and the AMC Manufacturers group developed stringent ASTM materials standards. These govern mechanical point anchor bolts and bolts using threaded and nonthreaded rebar. There are also minimum standards that suppliers must comply with in the manufacture of frictional bolts. However, most frictional bolt standards are based on the manufacturer&apos;s own specifications. It would be impossible to set uniform regulations on frictional bolts. Each bolt provides support in a slightly different manner and thereby requires different material needs. Quality Control In any case, material quality can generally be assured through tight order specifications and periodic quality control checks. The problem with installing quality anchors does not solely lie with the material. It includes all the events that occur from the time a bolt leaves a manufacturer to the time it is installed. The anchoring ability of any major type bolt can be affected by transportation, storage, mechanical performance of installation equipment, installation demands of the operator, proper drilling accessories, and local geology. Table 1 and Fig. 1 document the negative events that can affect each bolt and the degree to which it can be affected. Drilling a hole of oversized diameter, for example, is an operator controlled factor. It will adversely affect most bolts. An over-sized diameter reduces, or even eliminates, the anchorage capability of a mechanical shell. It will reduce the support capacity of a split set to nearly nothing. And it will cause a partial or incomplete grouting around the resin bolt. Frequently, due to bit wear, holes are drilled undersized in diameter and may not be properly cleaned out. In this case, it will be difficult for the operator to push the mechanical shell into the hole, thereby causing him to drill another hole. In cases where the bolt is obviously not providing anchorage, operators will probably drill another hole and place another bolt. Rock Bolt Regulations It is the situations where a bolt is improperly installed in the hole, but gives the appearance of a good bolt, that are frightening. In fact, some safety officials and engineers believe that only 50% to 60% of installed bolts are working. These bolts cause irregular ground load transfers in other bolts and overload them. This causes hazardous situations and overstressing. It is these bolts that fail prematurely 200 to 255 mm (8 to 10 in.) behind the face and possibly contribute to the high accident rate. The government and several manufacturers recognized the need to check the integrity of rock bolts. These programs are in different stages today. Tight torque regulations have been established for mechanical

Jan 4, 1985

By Earl T. Hayes

For several years the Northwest Electrodevelopment Laboratory of the Bureau of Mines, in cooperation with the Air Materiel Command, U. S. Air Force, has been studying zirconium alloys. A preliminary survey of these alloys has been completed and reported as a Bureau of Mines Report of Investigations. 4/ Originally the purpose was to determine the suitability of zirconium alloys in medium-temperature applications. However, data also were obtained on other properties of these alloys, and later the scope was broadened to include amore detailed investigation of a selected group. The zirconium-titanium system was one of those chosen. The Bureau of Mines has been instrumental in the commercial development of both of these metals and has constructed pilot plants for the production of titanium at Boulder City, Nev., and for zirconium at Albany, Oreg. Both elements are in subgroup A, fourth series of the periodic table, and therefore have many properties in common. Since both have similar atomic structures and lattice dimensions the possibility of extended mutual solubility seemed likely. Inc transition-point diagram of Fast indicated that the two metals are completely miscible in all proportions in both the alpha and beta forms.

Jan 1, 1951

By Elwyn H. King, Thomas R. Kuesel

I. CONCEPT MARTA&apos;s Peachtree Center Station is being mined out of hard rock, directly beneath Atlanta&apos;s central business district, with minimal surface disruption during construction. Its cost is competitive with that of a conventional cut-and-cover alternative owing to its design concept, which utilizes the rock as a primary structural and architectural material. II. PLANNING The station was originally planned for cut-and-cover construction. However, Peachtree Street is unusually narrow for a main business street (generally 78 feet (24 m) between building lines) and cut-and-cover construction would therefore be very disruptive to surface traffic and severely restrict access to adjacent buildings, including Peachtree Center, Atlanta&apos;s showcase business/commercial complex. (See Fig. 1.) Tunneling had been considered, but was initially thought [ ]

Jan 1, 1979

By C. C. Hawes

SILICA is the main impurity in iron ore. It is intimately associated with the iron oxide, sometimes free but more often in the combined state, as a mineral silicate. Its separation and purification sometimes present difficult problems to the analyst. In the absence of any definite knowledge to the contrary, orthosilicic acid. H4SiO4, is supposed to be the only silicic acid made, all other forms, such as metasilicic acid, H2SiO3, representing different degrees of its dehydration. These acids are exceedingly weak but form the most stable compounds found in nature. They are known as the silicate minerals and are formed by the combination of the different metallic oxides

Jan 1, 1936

By J. S. Malesky

"INTRODUCTION The Airdox method of breaking coal utilizes compressed air under high pressure and was developed to replace explosives. It is used in Illinois and Indiana mines to a large extent and also has been introduced in mines in a few other States.ACKNOWLEDGMENTThe author gratefully acknowledges the information and photographs furnished by the Cardox Corp.HISTORYIn the early 1920's, with the adoption of mechanical mining in States where on-shift shooting was prohibited, it became desirable to develop some means of breaking coal from the face without the use of explosives. At that time it was thought that a pressure of 20,000 pounds per square inch would be necessary to break the seal. It was impossible to obtain a compressor that would develop this pressure therefore, the 'patentees developed and applied the Cardox method, which utilizes liquid carbon dioxide as the blasting medium."

Aug 1, 1948

By J S. Kuszmaul, T O. Aspinall

The applicability of environmental geotechnics for erosion management is increasing in importance worldwide. The environmental impact of mining and evolving environmental legislation has been receiving increased attention worldwide in the last two decades (Bradfield, Shultz and Stone, 1996). The potential impacts associated with unstable spoil dumps from mine operations is the focus of concern both by the mining industry, environmental legislative agencies and members of the public. This is because of the need to increase the reliability of erosion prediction and in the minimisation of costs for spoil dump design. Engineered slopes of mine spoils may be stable at the end of construction, but they can deteriorate over time. Engineering design of mine spoil dumps seeks to reduce the potential for such erosion damage through correct selection of an initial stable landform scheme (Goh, 1997). The design of mine spoil dumps must also conform to the specifications of evolving legislation. The Queensland Environmental Management Overview Strategy (EMOS) states that, for minimised degradation of the surface area due to erosion during the development of a project, the erosion rates should be between 12 - 40 tonnes/hectare/year and that the depths of rills and gullies be limited to less than 30 cm (QDPI, 1988). The aim of engineering design is to ensure the long-term stability of the spoil dumps. The implementation of effective planning and operating procedures through recontouring and grading assists in the reshaping of spoil dumps to a safe, stable and non-erodible environment.

Jan 1, 1998

By M. N. Vu, G. Armand, A. Noiret, D. Seyedi

Extensive experimental observations have been performed around drifts and shafts at the Meuse Haute-Marne (North-Eastern France) Underground Research Laboratory (URL) to assess the extent and pattern of the induced fracture networks in Callovo-Oxfordian claystone. Two types of fractures can be distinguished, namely; shear (mode II) and extension unloading (mode I) fractures. The main goal of the present paper is to provide insights on the extent of damaged zone around the drifts by numerical simulations. A two-step approach is considered. First, 2D elastic calculations are performed for simulating the excavation of a drift following the direction of the major in situ horizontal stress. The evolution of the stress and strain tensors around drifts are calculated by applying an elliptic convergence function on the drift wall. Two failure criteria are then verified for the induced damage. An equivalent strain and an elastic energy based damage criteria are considered. The obtained results show that the employed simplified approach provides rather good results for the extent of the damaged zone for drifts parallel to major horizontal stress. However, post-processing elastic results leads to overestimating the vertical extent of the damage zone and underestimating its lateral extent, where the in situ stress state is quasi-isotropic in a section of drift. Nevertheless, the obtained results show that an energy based damage criterion could be considered as a potential way for reproducing the extent of the damaged zones if a convergence function can be defined for the drift.

Jan 1, 2015

By W. H. Jang

Recent research has demonstrated the utility of the FTIRIIRS adsorption density equation for in-situ study of surfactant adsorption phenomena at the surfaces of reactive internal reflection elements (IREs). The FTIR/IRS adsorption density equation is given by (formula) where r is the adsorption density, A/N is the absorbance per reflection, e is the integrated molar absorptivity, 4 is the bulk concentration of the surfactant, d. is the effective thickness, and dP is the depth of penetration. Previously, the validity of the adsorption density equation had been confirmed only from solution depletion measurements with high surface area powders. Now, FTIR/IRS studies of Langmuir-Blodgett (LB) monolayer films of fatty acid transferred to the surface of a calcium fluorite IRE .clearly validate the reliability of the FTIR/IRS adsorption density equation for quantitative analysis of surfactant adsorption. In addition, it was confirmed from the observed absorption band at 1550 cm-1 that the first monolayer of the transferred fatty acid chemisorbs at the surface of fluorite.

Jan 1, 1994

By Michael Jenkins

This paper reviews the history of rock burst research in the Coeur d&apos;Alene Mining District of northern Idaho over the last 30 years. Rock bursting is a problem because of a combination of geological factors in the region--complex structure, high horizontal stresses, and strong, brittle rock that readily stores strain energy. The Bureau of Mines has cooperated with industry to study rock burst phenomenon for many years. Early work focused on methods to mitigate bursting problems within the context of existing mining methods. In the 1970&apos;s, researchers began investigating methods for altering or controlling conditions that lead to rock bursts. These control measures become part of the stope development that precedes mining or are changes in the mining process itself. Although, researchers continue to develop microseismic techniques, the major research effort focuses on developing a new mining method to reduce the number and severity of rock bursts in order to improve safety and increase productivity in the Coeur d&apos;Alene Mining District.

Jan 1, 1987

By W. W. Vaughn

In the technique described and evaluated, detection of mercury is based on the principle of atomic absorption. An analog signal, produced when mercury vapor absorbs ultraviolet light, is converted to digital form and calibrated to mercury concentration. Interferences are eliminated by selectively trapping the mercury on gold. The lower limit of sensitivity, using a 1-gram sample, is 5 parts per billion. A model of the instrument mounted in a station wagon has been tested successfully in the field.

Jan 1, 1964