Search Documents

By Edwin W. Tooker

Creation of needed new resources will be accomplished mainly by imaginative and diligent geologic exploration because geologic availability is the key determinant of future mineral supply. Adequate resources of most commodities can be made available for the rest of this century and beyond if they are discovered. Thus conversion of hypothetical and speculative resources into available reserves will provide the principal challenge to earth scientists. Additional problems now compete for our attention. First is a challenge to discover more resources than have been found to date for domestic needs as world-wide demands increase exponentially and as easily found high-grade deposits are rapidly being depleted. New ways to find new types of deposits are required. Second, the United States, a resource importer, increasingly is challenged for access to foreign supplies through stiffening competition and economic or expropriation sanctions. Balancing needs for mineral supply and environmental protection is a third challenge. Geologic explorers must consider statutory as well as economic and technologic requirements, controlled access to public and private lands, competition with urban sprawl or wilderness, limitations on discovery, appraisal and mining methods, and restoration of mined areas. Finally, is the challenge to temper public and private attitudes and assure that decisions bearing on resource problems are based on comprehensive credible facts. While striving to maintain and improve the standard of living, many Americans appear to disdain and mistrust those organizations that provide their material where-withal. Meeting these challenges effectively, and in time, will require careful appraisal of the resource system and the joint efforts of industry, university, and government earth science research.

Jan 1, 1974

By James E. Rider

"Fractures in mine hoist drumshafts are rare. We know of no previously reported attempts to repair a fractured drumshaft; any feasible method would involve welding and the associated problems of distortion, crack formation and strength.In June 1984, a fracture was discovered in the drumshaft of the production hoist in the Teck Corporation, Lamaque Division Mine at Val d'Or, Quebec. Delivery time on a new shaft would have been at least six months. The shaft was repaired in ten days and the total out -of-service time was four weeks.This paper describes why the shaft failed, how it was repaired, and the special alignment procedures employed during re-installation to minimize stresses in the repaired area.IntroductionThe performance of a mine hoist drumshaft is absolutely critical to mine operation. An inoperable drumshaft means no hoist, which in turn means no production or mine operation.Fractures in mine hoist drumshafts are rare. Previously when they have occurred, no one has seriously considered attempting a repair because of problems involved. Any feasible method would involve welding, which raises several major problems - namely, metallurgical, alignment, and strength.In July 1984 this very situation occurred at the Teck Corporation, Lamaque Division Mine in Val d'Or, Quebec.It was recognized that a new shaft would take at least 6 months' fabrication and delivery time. However, having had some experience at repairing broken shafts in other machines under similarly desperate circumstances, and after due consideration, it was concluded that by applying the correct techniques and engaging the right expertise, it would be possible to perform a repair and have the mine back in operation within a month.Thanks to outstanding efforts by all, the repair was accomplished in ten days and total out-of-service-time was only four weeks. The causes of the failure were determined and the calculated stress levels confirmed by strain gauge measurement during operation.The success of this project was achieved by adhering rigorously to fundamental management and engineering principles."

Jan 1, 1988

By C. Musingwini

The South African mining industry continues to be a major source of employment at a time when at least 25 per cent of the working age population is unemployed. At the same time the industry faces a skills shortage in many of the disciplines necessary for its future health. The University of the Witwatersrand, University of Pretoria, University of Johannesburg, and University of South Africa have historically produced mining graduates for the South African industry, with any shortfall being met by the recruitment of overseas graduates. More recently the global shortage of engineers and other mining industry professionals has seen a reversal of this trend and a very significant emigration of well-educated and highly skilled personnel. The traditional career path for mining graduates is in production and mine management. However, there is the parallel and possibly more pressing need for specialized skills in such fields as ventilation, rock engineering, mine planning, mineral resource evaluation, and mineral asset valuation. It is in these essential areas that chronic shortages continue to hamper the development of the industry and may well frustrate its ambitions to be safe, healthy, and profitable into the future. The permeability of skills across sectorial boundaries within the mining industry requires that skills shortages in the platinum sector are not looked at in isolation, but within the context of the entire industry. This paper reviews the efforts being made by the universities at both undergraduate and postgraduate levels to meet the needs of the South African mining industry, in terms of the required numbers and the range of specialized skills.

Jan 1, 2012

By D. Turnbull, R. E. Cech

THE supercooling behavior of pure liquid metal droplets has been described.' The solidification behavior of small droplets of Cu-Ni alloys as a function of composition is described herein. The Cu-Ni system is of interest for such an investigation because the components are miscible in all proportions in both the liquid and solid state and the phase diagram of the system, Fig. 1, is a type often encountered in metal systems. It was noted by Van Riemsdyk2 and others that the nature of the "blick" of gold droplets during assaying is not perceptibly affected by the content of the platinum group metals that are soluble in both liquid and solid gold. With the exception of these very qualitative observations there appear to have been no prior investigations of the supercooling of alloy droplets. A series of nine alloys varying in composition by 10 pct (nominal weight) steps was made using certified OFHC copper, 99.996 pct purity, obtained from the American Brass Co., and electrolytic nickel pellets, 99.92 pct purity, obtained from the International Nickel Co. The alloys were melted and cast in vacuo in a high frequency induction furnace. Segregation was minimized by chill casting into 1-in. diam steel molds. Each alloy rod was homogenized at a temperature 50°C lower than the solidus for 100 hr in dry hydrogen. Samples for solidification experiments and chemical analysis were machined from the same portion of each rod and at a depth of in. from the rod surface. A Car-boloy tool was used in taking turnings to minimize contamination of sample by the cutting tool. As a check, a number of samples for microscopic observation were chipped from the ingot with a fragment of pyrex glass. The resultant data in all cases agreed, within experimental error, with the data obtained from machined turnings. A number of small particles, 30 to 50 micron diam, of a Cu-Ni alloy were placed in a quartz vial 1/32 in. diam x % in. long. This was inserted into a platinum ribbon heater and mounted in a high temperature microscope stage. The general procedure followed in inserting samples into the stage and measuring the temperature of melting and solidification was the same as described in an earlier paper.' A chromel-alumel thermocouple was used to study alloys of 88.93 pct Cu, 80.62 pct Cu, and 72.27 pct Cu. A platinum-10 pct rhodium thermocouple was used for the remainder of the alloys. Procedure The assembled high temperature microscope stage was first evacuated and the sample given a 2 min in situ treatment at 900 °C in dry hydrogen to remove surface oxides which might otherwise catalyze crystal nucleation. After this treatment the atmosphere was changed to purified helium and melting and solidification were observed microscopically. It was not possible to determine the solidus with certainty. However, the liquidus temperature was measured very accurately since the surface of the particle changed in appearance from coarse and uneven to smooth, mirror-like within a few degrees. The visually determined liquidus temperature was checked by finding the highest temperature to which the particle could be heated such that it did not supercool upon lowering the temperature. This temperature which checked within experimental error with that found by observing surface change was assumed to be characteristic of the thermody-namic liquidus. In order to minimize the effect of selective evaporation of copper from the alloy, samples were changed frequently and the droplets were heated no more than 50 °C in excess of the liquidus temperature T,. When the latter conditions were fulfilled, T, values were reproducible. After melting, the temperature was decreased slowly until the particles solidified. The sudden release of heat of fusion on solidification caused the

Jan 1, 1952

By Carlos Castañeda Reaño

La presente investigación señala la etapa de creación de las organizaciones de seguridad y de SOGESA, funcionamiento, orientación inicial y el programa mínimo de ejecución inmediata y progresiva. El programa de seguridad se inició en 1980. La técnica impuesta para este programa surge de un compendio de la experiencia desarrollado en programas anteriores. La aplicación se dio en la industria metalúrgica de Cerro de Pasco, y luego en la industria azucarera con la Grace Co. de la hacienda Cartavio, no lográndose definir el programa por completo. En este sentido, se perfila el planeamiento de un programa mínimo a través de un estudio a corto plazo de la situación real en SOGESA y se precisa el lugar que ocupa la seguridad e higiene industrial dentro de una organización. Asimismo se describe las necesidades mínimas del equipo de seguridad y protección, como la difusión de la creación de un conciencia de seguridad en cada trabajador a través de charlas, exhibiciones y reuniones con jefes de servicio y supervisores. También se desarrollan otros elementos estructurales de seguridad como las inspecciones, brigadas de voluntarios de seguridad, estadísticas, campaña contra incendios e higiene industrial para la comunidad, respectivamente.

Aug 20, 1963

By HENRY M. PARKS

THE total production of all metals in Oregon to date is estimated at $160,000,000; ~115,000,000 from eastern Oregon and $45,000,000 from the western part of the state. In 1916 the metal production of the state was approximately $4,000,000, while the present annual production has dwindled to a little less than $1,000,000. Western Oregon The state of Oregon contains several metal-bearing areas, widely scattered in different regions. More than half of its coast is fringed with a belt of auriferous sands which sometimes are rich in fine gold. A second mining field, the chief producing one of western Oregon, is situated in the southwestern part of the, state and includes Jackson, Josephine, Douglas, Coos and Curry counties. It may be considered as the northern extension of the gold and copper belt of California. A third region in western Oregon is that on the western slope of the great Cascade range in the Bohemia, Blue River, Quartzville, North Santiam and Ogle Creek districts-from the Siskiyous on the south almost to the base of Mt. Hood near the Columbia River on the north.

Jan 1, 1925

By R. L. Crosby

The Bureau of Mines investigated alloys of copper with 2, 3, and 4 vol pct alumina and with 2 vol pct yttria. Alloys were prepared by a coprecipitation process and were fabricated by pressing and sintering of powders, extrusion, and swaging. Tensile properties at room and elevated temperatures, stress-rupture strength, electrical conductivity, and density were measured. The superiority in elevated temperature strength of dispersion-strengthened copper to OFHC copper was confirmed. Increasing the oxide content from 2 to 4 vol pct produced only a small improvement in strength properties and decreased the electrical conductivity. The 3 vol pet alumina alloy had the best overall combination of properties.

Jan 1, 1969

By Randall Head

The drilling at the Taum Sauk Reservoir was a unique compilation of the latest technology and everyday common sense. This site is comprised of rhyolite, which is 30 times harder than limestone in comparison. Using some of the most state of the art drills, coupled with GPS guidance, angular drilling systems, and an ordinary piece of string, some of the most amazing drilling feats were accomplished. By constructing the new dam on top of a mountain that had been blasted once before nearly 50 years ago treacherous conditions for the drills and crew were a challenge. The drills had to be flown in by cranes to get to their locations, where they then drilled anywhere from 2.5 to 6 inch (6.4 to 15.2 cm) holes at angles up to 24.4 degrees. Custom drill bits were designed by the drilling crew to tackle feats such as drilling holes up to 120 feet (36.6 m) deep. A main challenge was the shape of the reservoir, as it is not in a straight line, but rather round, so no technological way was readily available to use to drill. Common sense came in and an ordinary piece of string was used to aide in drilling the hole. A revolutionary step was that our drill was used to core our own samples. By using our own equipment, we were able to complete this task for one-third of the cost of having a third party contractor obtain the core samples. On this unmatched jobsite, it has been established that technology has come a long way, but when all else fails, a piece of string will do just fine.

Jan 1, 2010

By Jessica M. Wempen, William G. Pariseau, Dallan J. Coons, Michael K. McCarter, Erik C. Westman

The abstract discusses the importance of proper pillar sizing in underground mining for safety and efficiency. It highlights the use of theoretical models, geotechnical measurements, and numerical modeling in predicting pillar behavior. The research focuses on using seismic tomography to image stress changes in a yield pillar at a longwall mine as the longwall face approaches. The study aims to compare the stress distribution imaged using tomography with theoretical models, geotechnical measurements, and numerical models.

Mar 18, 2022

By Wing G. Agnew

[This report presents the results of tests made by the Mining Division, Bureau of Mines, on the relative durability of manganese-steel drill rods and carbon-steel drill rods for use with the detachable bolts]

Jan 1, 1941

By C. A. Heiland

THIS year's review of geophysical activities has a somewhat different complexion than usual. With the ending of the war, the time seems opportune to supplement the customary report on operations and discoveries in oil and mine exploration by a review out-lining the contributions of geophysicists to the. war effort. To give as much space as possible to the latter, presented as Part 2, some of the usual review features have been omitted from the statistical section, given as Part 1 immediately following.

Jan 1, 1946

By S. S. Sephton, Kirit C. Vyas, Melvin J. Greaves

Energy requirements for various pelletizing systems are considered from a fuel and power aspect, with the presentation of typical energy heat balance flow sheets. A partial calculation for the firing zone of a straight grate system is shown and a comparison of an actual measured and a theoretical-calculated heat balance for a grate-kiln is presented. The power used for each pelletizing system and future possible energy savings a1•e also reviewed.

Jan 1, 1976

By Dilip Banerjee

"This paper discusses the Advanced Technology Program (ATP)'s support over the last decade to the development and use of process modeling as a tool to address some of the challenges faced by the U.S. metal casting industries. A particular focus will be given to highlight how process modeling can be used to improve the manufacturability of components needed for high performance and critical applications. The challenges associated with the design and production of thin-walled, cast parts with intricate and complex internal geometries will be discussed. Modeling issues associated with the control of the final grain structure in the solidified parts will also be addressed. This paper will describe the advantages of using appropriate mathematical models for designing new alloys for use in various applications.Finally, the role that ATP has played in uplifting the U.S. technological base through partnerships with industry and academia in high-risk research in order to bring to market new and improved products for the broader benefit of the nation will be discussed.ATP's BackgroundIn the 1980s, U.S. industries were losing market share to low-cost, high-quality manufacturers from Asian countries. Corporate leaders and policy makers determined that in order to sustain and grow market share, U.S. industries needed to improve their competitiveness and productivity through product and process innovation. There was evidence that companies were systematically under-investing in leading-edgetechnologies and failing to complete the development of new technologies [l]. There were also arguments in academic circles that pointed to a potential market failure in the area of early-stage technological developments. These concerns provided impetus for creation of the Advanced Technology Program (ATP) within the National Institute of Standards and Technology through the Omnibus Trade and Competitiveness Act of 1988. Through a rigorously competitive, cost-shared partnership with industry, ATP fosters the development and broad dissemination of high-risk technologies that offer the potential for significant broad-based economic benefits to the United States."

Jan 1, 2004

By K. S. Izbakhanov

The Chimkent Lead Plant was constructed in 1934 and since that time has undergone many revisions. In 1975 the slag fuming operation was changed from pulverized coal to natural gas fuel. In 1981 the slag fuming furnace water jacket system was converted to evaporative cooling with high pressure steam production. The impact of these changes and the method of their application are described.

Jan 1, 1990

By R. E. Heithecker

The separation of enormous quantities of water produced with the oil in some West Texas fields necessitated the use of special equipment other than the regular lease tanks. Several methods were used with varying degrees of success. They include the water-trap, hay tank and gun barrel, gun barrel and settling tank, chemical and electrical-dehydration methods. The water trap which has been used extensively in the Hendricks field, and in some instances has been installed in the Yates field separates the water and. oil under high pressure before tile liquid and gas pass through the flow beam. The first trap was constructed and installed by the Southern Crude Oil Purchasing Co. in July, 1928. By July, 1929, approximately 300 traps were in use. Treating cut oil by running it through a hay tank was done quite extensively in the Roberts-Settles field, Howard and Glasscock Counties, Tex., and later the method was used in the Hendricks field. In July, 1931, there were 37 hay tanks in the Roberts-Settles field, treating the oil from 123 wells. The cut oil frequently was made acceptable to the pipe-line company by running it through the hay tank. In some instances, however, it was necessary to heat the oil, and occasionally both heat and chemicals were used before complete separation of the oil and water was obtained.

Jan 1, 1932

By D J. Williams, E M. Rykaart

Soil cover systems are routinely used to reduce acid rock drainage (ARD) from mine waste rock dumps and tailings impoundments. A technology for the analysis, design, instrumentation and monitoring of barrier-type (oxygen limiting) and store/release-type covers has rapidly developed and the number of covers under construction has grown extensively during the past ten years. Mine operators are currently investing in this relatively new technology with the expectation that these covers will reduce long-term liability with respect to acid generation, drainage and treatment costs. While the design life for cover systems may extend into hundreds of years, we have less than ten years of construction experience and proven performance. Some cover designs appear to be functioning well; however, the performance of many more is now being called into question. The paper presented herein evaluates the integrity of cover systems from a global perspective. Soil cover systems for the control of ARD are being constructed at mine sites located within high rainfall equatorial regions, deserts ranging from low to high latitude, humid temperate regions, and cold-continental climates. While the technology for analysis and design of soil cover systems is well developed, factors that compromise the performance of cover systems (in addition to the paramount issue of climate) relate to material selection and availability, cost and construction practices. Long-term performance is also strongly affected by physical stability (ie erosion), volume change (ie cracking, desiccation, settlement and freeze/thaw cycling), vegetation, soil evolution and ecological stability. This paper provides a review of the application of soil cover systems for the control of ARD. Cases where cover systems have been constructed with both success and failure are illustrated. General criteria and recommendations for cover selection, design, construction, and maintenance are provided.

Jan 1, 2003

By N. A. C. Smith

This report on the physical and chemical properties of typical crude oils of southern Louisiana and southern Texas is the seventh in a series of preliminary chapters of a bulletin covering the producing districts of the United States. Preceding reports* may be obtained from the Bureau of Mines on request. The details of the methods used in this survey in collecting samples and making laboratory tests have been discussed in the first three papers. A method of summarizing and interpreting the laboratory data has also been given, but most of the crudes included in the present report differ so radically from those previously reported, that it has been found advantageous to adopt a somewhat different method in making summaries. This method is described in detail later. If any errors or omissions are noted by readers, it is hoped that these will be brought to the attention of the Bureau of Mines, for correction before the appearance of the final bulletin.

Jan 1, 1922

Power plants that utilize conventional wet flue-gas desulfurization methods produce enormous amounts of flue-gas scrubber sludge. A typical 400 MW power station that burns a high sulfur coal produces 170,000 tons of wet flue-gas scrubber sludge per year. This scrubber sludge is currently landfilled at an enormous cost to utility companies. This material could be used as a raw material for industries that use gypsum, such as the wallboard and plaster industries. However, before it can be used as feedstock for these industries, some of the impurities such as unreacted limestone and silicates must be removed from the scrubber sludge. Froth flotation has tremendous potential for separating these impurities from scrubber sludge. In order to select an optimum flotation process, it is necessary to characterize the surface properties of the major components in the scrubber sludge, which consist of calcium sulfite, calcium sulfate, calcium carbonate (limestone), and silica. In this study zeta potential measurements were used to determine the surface charge of the components in scrubber sludge, with the goal of optimizing a froth flotation process to produce a marketable gypsum product for the wallboard and plaster industries.

Jan 1, 1996

By E. T. White, Dean Ilievski

"Mathematical modelling of the precipitation process requires that the kinetics of crystal growth, nucleation and agglomeration be known. This paper reviews the current state of knowledge on these precipitation sub-processes (ie. growth, nucleation and agglomeration) and describes a number of experimental techniques for estimating their kinetics. The experimental methods used to generate the precipitation data and the data analysis techniques used to extract the kinetics information from the data are discussed separately. There is no universal ""best"" technique for determining the kinetics. However, studies on multi-crystal systems are more reliable for modelling purposes than are single crystal studies. The selection of a technique will depend on which sub-processes are present. A problem with all kinetics studies is that there is generally a large uncertainty in the estimated kinetic parameters. This stems from the scatter in the experimental data being further propagated by the mathematical techniques used to extract the kinetic parameters.IntroductionCrystallisation operations, including precipitation, are widely used in a number of hydrometallurgical processes to recover a desired component or to remove an undesired impurity. The goals of industrial precipitation processes are to maximise the recovery while maintaining product quality (generally product crystal size distribution, purity and morphology and product handling properties). Knowledge of the precipitation mechanisms and kinetics is invaluable for designing new precipitators or for improving existing units. The mechanistic and kinetic information is generally incorporated into mathematical precipitator models, which are then used for process design and optimisation."

Jan 1, 1996

By J. E. Schiller

The Bureau of Mines is investigating methods to treat waste water that contains cyanide. This report describes a new method that removes heavy metals and all forms of cyanide. In the first step, hydrogen peroxide and sodium thiosulfate are added at pH 7 to 9 in a 1:2 molar ratio to convert free and weakly complexed cyanide to nontoxic thiocyanate. Then steryldimethylbenzylammonium chloride is added to precipitate ferro-cyanide, and finally, ferric sulfate is added as a sweep floc and sequestrant for heavy metals. After the suspended solids settle, the water is polished by filtering. The water initially contained 1 to 5 mg/L Fe, 1 to 5 mg/L Cu, and 10 to 30 mg/L total cyanide; the level of each of these constituents was reduced to less than 0.02 mg/L.

Jan 1, 1983