Search Documents

By Neal M. Miur

"INTRODUCTION The Mineral Ridge-Clay Lick fault system in Crittenden and Livingston Counties, Kentucky, is one of the larger and more important fault systems of the Western Kentucky Fluorspar district. Total production from it up to July 1945 (chiefly since 1900) was approximately 80,000 tons of fluorspar ore, 10,000 tons of which came from the Mineral Ridge Fluorspar Co. tract 1, which was being operated by the Mahoning Mining Co. of Rosiclare, Ill. The fluorspar ore carries lead and zinc that can be recovered by milling, and the Mahoning Co. planned to log-wash the ore at the mine and then mill it in its mill at Rosiclare, The Mineral Ridge Fluorspar Co. properties were examined by O. M. Bishop, an engineer of the, Bureau of Mines, in August 1942. During 1943 and 1314, developments on the properties were under observation by X. B. Starnes, of the Bureau, and it was decided to diamond-drill tracts 1 and 2, as indications seemed favorable for opening up additional fluorspar ore bodies. Drilling was begun March 12, 1945, and was completed July 2, 1945, during which time 12 holed were drilled on tract 1 of the Mahoning Co.'s leases for a total of 3,637.1 feet, and one hole 359 feet deep was drilled on tract 2 of the Jennings lease. The Mineral Ridge-Clay Lick fault system, 4 to 47 feet wide, was encountered in all holes at 126 to 265 feet."

Apr 1, 1947

By T. D. Hackett

Multislice mining methods were analyzed by the U.S. Bureau of Mines to determine their application to western United States thick coal seams; ground control, geology, and costs were considered. Multislice mining is used in widely varying seam conditions worldwide, including flat seams too thick to mine in a single pass, pitching thick seams, and seams containing a rock parting. Longwall multislice methods predominate, but room-and-pillar variants also exist. The initial use of the method in western seams is planned at a deep Colorado mine where a rock parting will be used to separate two slices mined by longwall. Ground control and spontaneous combustion are major hazards associated with multislice mining. A well-consolidated upper slice gob can reduce ground control problems and provide a seal against spontaneous combustion. Geologic analysis indicates that the consolidation of the gob depends on the composition of the upper slice roof, the presence of water, and sufficient overburden pressure. A geologically competent intermediate rock parting can also reduce ground control problems and seal against spontaneous combustion. To compete in western coal markets, the cost of multislice mining must be within the range of normal longwall costs. Analysis indicates that multislice operating costs should be within this range, and that multislice mining costs decrease as panel width increases. Relatively wide (600 to 800 ft) panels also provide increased coal recovery.

Jan 1, 1990

By Betty J. Laswell, Gerald W. Laswell

Rotary drilling in modern open-pit mining is usually considered the lead phase which not only establishes the production rates but frequently limits them. From this viewpoint alone, the drilling phase must be maximized. The drill phase is the step that permits all the other operational phases to function within their design limits. This means that, in most cases, the drill is literally run to destruction to ensure that the shovel will be able to smoothly and consistently load a manageably size muck, the haul trucks can carry a balanced load without having a boulder dropped through the bed, and the crusher can devour constant rock size.

Jan 8, 1978

By Cory Bolen, Nadav Bar-Yaakov, Eric Zimmerman, Gregory Raines

The Chimney Hollow Reservoir Project broke ground in August 2021, constructing the tallest Asphalt Core Dam in North America, intending to improve reliability of drinking water supply to Northern Colorado communities. Aiming to expedite and streamline the geological mapping process in the tunnel, Stantec’s teams have developed a mobile and web-based GIS application for digital mapping input and rock mass evaluation, allowing real time decision making for assigning tunnel support class and resulting in a faster more efficient process. The following article presents and demonstrates the GIS mobile and web application-based process, the mapping results and review additional uses of the database created.

Jun 13, 2023

By Danny Déry-Chamberland, Peter Bowman, Michael Byle

"The Barrage des Quinze dam is a concrete sluice dam consisting of 19 spillway sections, each of which is approximately 7.6 metres wide and 14.5 metres deep. Rehabilitation efforts being performed on the dam including demolition and improvement of the roadway and spillway sections and grouting to mitigate underseepage. Initially, conventional cement grouting was attempted and was successful in 14 of the spillway sections, but unsuccessful in 5 of the sections due to the high water flows which washed the grout away. The removal of the roadway and portions of the piers during construction temporarily reduced the stability of the structure limiting grouting pressures that could be applied. This and the substantial high water flows (leakage) beneath the dam between the concrete/rock contact and within fractures in the upper rock formation created a challenging situation to create a cutoff.A grouting solution was developed that involved implementing several different grouting methods and materials including balanced high mobility grouts (HMG); low mobility grouts (LMG); polyurethane grouts; and sodium silicates. Because of the critical scheduling for the work, multiple approaches were planned and made available on site so that the work could proceed with the best technology with little, if any, time loss. The end goal of the grouting program was to create a seepage cutoff beneath the 5 sections of the dam in a stepwise process. The initial step was to fill the large openings and create a grout barrier to reduce the high water flow. The second step was to seal the contact between the base of the dam and the bedrock; and the third step was to complete closure by grouting a deep grout curtain into the underlying rock. Other features of the work included an extensive grout mix testing program, water pressure testing, borehole camera survey, and monitoring of the grout injections."

Jan 1, 2016

By R. Adsero

"In view of the decade long decline in worldwide mine equipment productivity and with heavy economic pressures and survival at risk, improvements for those remaining in the game are essential. The latest Multifactor Productivity data for the US mining industry indicates a continuing descent with Australia on a similar course. The world’s mining industry has a fleet of over 400 large draglines moving billions of tons of material annually. The most efficient use of this equipment resource will provide a competitive advantage to those companies who are committed to improving performance. A dragline monitoring system is a requirement for optimum operations. The monitor reports the facts. Focused actions can change the facts and create improved performance. Analyzing monitor data to build knowledge and create understanding is a beginning. Understanding the key productivity indicators for dragline operations and an effective benchmarking process are the basis for improvement. There is overwhelming evidence that adopting new technologies and concepts including AC drive technology can and will bring about a step change in dragline operating cost with improved production performance.STATE OF THE MINING INDUSTRY A high altitude review of the state of the mining industry provided by a study of multifactor productivity shows a continuation of lower and lower output year on year for the capital and labor inputs applied. The story is sadly similar for both U.S. mining and the Australian mining sector. In fact, according to PwC analysts the worlds mining equipment productivity has declined 20% over the past seven years. (Lumley, 2014) Although the reasons for the continuing decline in mining productivity are varied, the need for improvement is clear. The world’s mining industry fleet of well over 400 large draglines moves billions of tons of overburden and ore (phosphate, limestone, etc.) annually.This discussion will review a few of the tools available for improved productivity in dragline operations."

Jan 1, 2016

By V. O. Tenorio, D. Tolmachoff, K. Willa Brown, K. J. Kingsbury, J. B. Nickels, G. J. Nail

A major design feature to consider from the initial pioneering works until reaching full mine production of icy regolith at the South Pole of Moon will be the ramp. This will allow the access of equipment and personnel in and out of the excavation area. Although most of the requirements considered when designing a ramp on the Earth are similar, the fact of working in low gravity, with zero atmosphere, the potential exposure to high radiation, extreme temperature levels and drastic changes of illumination, from intense light to total darkness, are new factors to be included. Transversal sections are obtained according to the progression sequence of the production levels, with changes in length, gradient, friction factor of the terrain and curvature when required by the location characteristics and the specification of the equipment utilized. A MATLAB script was developed to calculate all the variables, in order to obtain 3D generated surfaces from the range of possible profiles.

Mar 2, 2022

By J. S. Lewis

Beneficiation and physical and chemical processing of non-terrestrial materials borrow strongly from terrestrial experience, but also involve the necessity of handling literally un-Earthly feedstocks, reagents, and environmental conditions. The present state of scientific and engineering understanding of the processing of non-terrestrial minerals, gases and hydrocarbons is reviewed with the production of rocket propellants, life-support fluids, structural metals, and refractories as the goal.

Jan 1, 1992

By Thomas C. Poulter

Abstract The Poulter seismic method of geophysical exploration is an attempt to obtain an increased efficiency in the conversion of the energy of an m~pl06ion into useful energy which has directive properties and which contains a minimum of random frequency and random phase relations. Very little effort has been made in the past to simplify OT even control the uniformity of the seismic energy being introduced into the ground. The Poulter seismic method is also an attempt to improve the signal-to-noise ratio not merely by trying to complete the impartial filtering done by the earth on ,the continuous spectrum of primarily high-frequency energy radiated from a shot point but by applying a frequency control at the point of origin of the seismic wave. The energy from a shot-hole charge is peaked in a frequency which is much higher than will be transmitted through the ground, and its absorption introduces background interference. Only 10 to 20 per cent of the seismic energy of a shot-hole charge .is directed downward in a 90-degree vertical cone, whereas, from a pattern of charges detonated above the surface of the ground, 85 per cent of the seismic energy is included in a 90-degree cone and in some cases it is even confined to as small as a 30-degree cone. This greatly reduces the horizontally distributed energy, thereby producing a marked improvement in the signal-to-noise ratio. The frequency of the signal energy may be peaked in a rather narrow range by the proper application of two or more impulses upon the surface of the ground controlled as to direction, magnitude, and timing. These impulses may be controlled by the reflection shock wave technique, the pressure pulse technique, and the sequence firing technique, using the primary controls as outlined. The information obtained from the study of directivity of seismic energy in a high velocity, uniform material such as the ice on Taku glacier, in the Juneau ice field in Alaska, has been of great assistance in the application of the method to oilfield and mining problems.

Jan 1, 1950

By William H. Lehr

A 4200 ton-per- hour marine transfer terminal, where river and oceangoing vessels simultaneously exchange cargos of coal and phosphate rock, is now in operation near the mouth of the Mississippi. Its materials handling machinery includes a bucket ladder barge unloader; a rope operated clamshell bucket unloader; a coal loader; and a rail mounted bucket wheel machine. The design and operation of this equipment is described as are the docks and conveying, breasting and barge-haul systems in use at the facility. Design considerations imposed by soil and river conditions, geography, operating needs and investment requirements are discussed. The economic significance of design and shipping innovations introduced by this facility is noted.

Jan 1, 1967

By James A. Finch, Stéphanie Somot

"The self-heating facility developed at the Noranda Technology Centre [Rosenblum and coworkers, 2001; 1995] has now been established in the Department of Mining, Metals and Materials Engineering at McGill University. A research program into mechanisms has been initiated (with support now from four industrial partners under Camiro). The first investigation is into the role of pyrrhotite (Po), the most commonly suspected mineral to trigger self-heating. Following a standard experimental protocol, self-heating was assessed on samples of Po mixed with sand as an inert material. With increasing Po content, self heating progressively increased but, interestingly, the samples visually appeared less and less oxidized. A high Po content, it was hypothesized, may give a more reducing environment favouring formation of H2S. The presence of this gas could be significant as it has a high exothermic heat of reaction with oxygen. The system was modified to test the hypothesis by including copper pieces and copper sulphate to react with (and therefore reveal) the gas as copper sulphide. Evidence is presented in support of H2S production, which to our knowledge has not been shown before and introduces a potentially important avenue of investigation into self-heating mechanisms.INTRODUCTIONSelf-heating of sulphide minerals poses potential environmental and safety hazards in mining of ores, and storage and transport of concentrates. While some conditions are known to be critical, the reactions remain poorly understood making self-heating difficult to predict and control.A major advance in measurement was introduced by Rosenblum and co-workers [Rosenblum et al., 2001; Rosenblum and Spira 1995]. A self-heating assessment method was developed and applied to various sulphide-bearing materials The method is based upon automated calorimetric cells with data acquisition, now available to McGill researchers and which have been used for the study reported here."

Jan 1, 2006

By M Spagnolo, M Ashley, D, L Reemeyer

PasmincoÆs Century Concentrator in North West Queensland commenced operations in November 1999. The nameplate production capacity of 500 000 tpa of zinc metal production in concentrate was achieved in August 2002. Completion of the production ramp up was successful due to the culmination of a number of initiatives throughout 2001 and 2002. Mine to mill interaction to understand and eliminate head grade related bottlenecks affecting Concentrator production and reduce feed variation. Grinding circuit process development û operating and process control strategies to improve stability and reduce grind size to support zinc recovery. Pumping upgrades to control spillage in ultrafine zinc flotation Low density zinc flotation strategy û to improve silica-sphalerite separation to improve zinc recovery while maintaining acceptable silica in final concentrate. Flotation circuit process development û froth crowders, froth cameras and reagent control strategies to improve primary zinc flotation performance. Review and implementation of longer campaigns between planned shutdowns to improve availability. Team reorganisation û to improve setting and implementation of metallurgical strategies. This paper describes these initiatives and their contribution in achieving the production target. It also notes the ball mill motor failures that delayed the successful achievement of the ramp up, and CenturyÆs response to minimise the production impact. The paper also outlines the capital improvement program that was implemented to improve zinc recovery to design 82.5 per cent recovery once the production rate had been achieved.

Jan 1, 2003

By F. J. McMulkin

This paper, the 1965 Airey Memorial Lecture, reviews the world-wide technical advances in iron and steelmaking, and offers an appraisal of the new techniques which will be applied in the future. After a review of blast furnace operations, the continuous steelmaking process is described, and the resulting techniques of degassing and continuous casting are discussed at length. Pressure pouring, hot rolling, cold rolling and coating practices are also outlined, and considerable space is devoted to the direct reduction process. Finally, the application of the computer to steelmaking operations is discussed in some detail.

Jan 1, 1966

By J F. Short

The jet piercing process, developed by Union Carbide Canada Ltd., is well established in blasthole production in open-pit mining. By this process, holes can be drilled, shaped and chambered for blasting. In suitable ore or rock formations, a considerable cost reduction can be achieved. This paper reviews the equipment used, relates how cost savings may be accomplished, and concludes with a mention of the most recent developments in this field. JET piercing and chambering, a process for blasthole production in open-pit mining, leads, in many instances, to improved drilling and blasting techniques and costs. It is a method of working rock with a supersonic flame and, to be most effective, depends upon a characteristic of the rock called spallability. Spalling, in this case, is the breaking away of surface particles from the rock body due to stresses caused by the thermal shock of the jet flame. Various rock properties contribute to this action, but, in general, the harder the rock the greater the spallability and the more effective and economical is the jet process. The jet process has the capability to drill, ream, shape and chamber holes for blasting.

Jan 1, 1965

By D. H. Flather, J. W. Hendry, K. Drover

Black Hawk Mining Inc. has completed a comprehensive program on the prediction and management of acid rock drainage (ARD) at their Keystone Gold Mine (Keystone) near Lynn Lake, Manitoba. The program, initiated in 1994, followed a phased approach utilizing initial acid-base accounting (ABA) results and subsequent laboratory kinetic testwork to define site-specific sulphide oxidation and neutralization consumption rates in waste rock. Net acid generating waste rock at Keystone was defined through the kinetic testwork as waste rock yielding a net potential ratio (NPR) of less than two. A preliminary waste rock management program based on blending of potentially acid generating and acid neutralizing waste rock was advanced. Subsequent refinement of the management program followed the analysis of over 1580 ABA samples collected from individual blast holes during the initial bench development phase of the Keystone pit. Uncertainties in actually achieving adequate blending within the dumps at a mining- scale resulted in the development of a revised waste rock management program based on segregation. Recognizing that any successful management plan requires that the ARD characteristics of the waste rock be identified prior to in-pit blasting, the extensive ABA database was utilized to develop a rapid characterization scheme. By implementing a characterization scheme based on total sulphur concentrations and fizz rating, waste rock could be quickly segregated without delaying the natural flow of ore from the pit. Interestingly, it also became apparent that gold values were strongly correlated with total sulphur, such that traditional fire assays were supplanted with a simple and more cost-effective total sulphur determination. The program highlights the importance and benefits of collecting and exploiting data beyond that necessary to acquire appropriate development permits.

Jan 1, 2000

By P. Balachandran

The paper outlines the existing facilities and working practices at the Khetri electro-refinery of Hindustan Copper Limited. Plans have been drawn up to mechanize some key operations to improve the quality of cathodes and the working environment as well as economize the refinery operations. The economic analysis for determining various optimum operational parameters under conditions existing in India have also been outlined. The impact of capacity utilization and mechanization under different sets of conditions on operational costs have been highlighted.

Jan 1, 1987

By Judson G. Brown

In the May, 1969 issue of Mining Engineering the Editorial Director, John V. Beall, described the Japanese Onahama Copper Smelter and Refinery as follows: "On the shore of the Pacific, 120 miles north of Tokyo, is the world's most modern copper smelter and refinery.? One of the improvements that has been made at the Onahama Refinery is the quality of the electrolyte in the copper refinery electrolytic cells. This has been accomplished by reducing the concentration of slimes in the cells between the electrodes. In a December 19, 1966 review in Chemical Engineering magazine reference was made to some tests in Sweden as follows: ?However, at 1,000 amps/sq.M., satisfactory cathodes could be prepared, provided electrolyte flow past the anode and cathode was at least 3 to 4 meters per minute, and the slime content was not allowed to exceed 20 to 30 mg. per liter. By dropping the current to 500 amps with the same electrolyte velocity, the slime content could grow to 50 mg. per liter (50 ppm) without causing occlusion at the cathode." From this data it appears that the production capacity of copper refining electrolytic cells can be significantly increased. In order to do this the concentration of suspended contaminating slimes in the electrolyte solution is reduced by filtration. The electrolyte in-between the active electrodes must be purged with higher velocities to maintain a high concentration of the desirable copper ion in the liquid film adjacent to the cathode and the sulfate ion in the liquid film at the anode. This higher velocity also carries away from the cathode the undesirable impurities released from the anode as they are released into the electrolyte as filterable solids.

Jan 1, 1970

By Fred R. Ingram

FOR the purpose of this discussion, let us consider that the Rocky Mountain region covers the area in the seven Mountain States, Idaho, Montana, Wyoming, Utah, Colorado, New Mexico, and Arizona, and before we discuss the needs of these states, let us define Industrial Hygiene. Industrial Hygiene is that branch of preventive medicine concerned with the protection of health, improvement of efficiency, and prolongation of life of the industrial worker; in short, adult health conservation. It includes in its broad meaning not only the prevention of occupational diseases, such as silicosis, lead poisoning, cadmium poisoning, and many others, but such relative problems as overcrowding, fatigue, and personal and mental hygiene; exposure to abnormal temperatures, pressures, and humidities; ventilation, heating, and lighting. It is a science which requires the combined activity of medical personnel (doctors and nurses), engineers, and chemists to evaluate the exposures and determine the means of eliminating the hazard. The engineer surveys the workplace, takes air samples at the breathing level of the workman, and analyzes the work exposure. The chemist determines in his laboratory the exact amount of toxic material collected in the sample, which represents the exposure of the workman. The doctor must diagnose the occupational disease, recognize its cause, and evaluate the disability. Together, all three must correlate the data obtained and devise efficient methods, medical or engineering or process changes, for controlling or minimizing the dangerous condition and for studying the effectiveness of these measures. The plant doctor, in addition, must aid in the readjustment of the incapacitated worker and provide facilities for prevention. Industrial hygiene, however, is of no avail without the understanding co-operation of management.

Jan 1, 1945

By R. S. Jurani

Sunshine Mining Company's Kellogg operation is the primary silver producer in the United States, and maintaining a comfortable working environment in this deep underground mine historically has been a complex and costly problem. To improve the ventilation and cooling systems at a time of declining and uncertain silver market, it was proposed to optimize the performance of existing facilities at minimum cost. This paper discusses a 2-year, $400 000 optimization program that resulted in increased total mine airflow, cooler ambient temperatures, reduced compressed air usage, and lower energy consumption by primary fans, air compressors, and refrigeration plants, thereby saving the company approximately $650 000 per year.

Jan 1, 1987

By W. W. Atkinson

This paper describes some concepts developed in a geologic data recording system at the Victoria, Nevada breccia pipe-skarn copper mine. The recording system is not fundamentally new, but represents expansion of earlier ideas. The paper is based on the philosophy that a high quality geologic data base is necessary and that it should be complete, clear, standardized, neat, quantitative, and readily useable. It may be multi-colored or simply black and white. Graphic, descriptive and quantitative recording of data is essential. A format for core logging is presented and discussed and as well as a multiple overlay system for recording data gathered in surface mapping.

Jan 1, 1983