Search Documents

By Inc. Pile Dynamics, Daniel S. Belardo, Marcus Galvan, George Piscsalko

Soil nails are often utilized as a temporary or permanent earth retention technique for slope stabilization and for excavation retention for existing or new structures. Soils nails are generally advantageous as installation is relatively rapid and they can be installed beneath existing structures and where site access for equipment is limited. Due to the typically small cross-section of these elements, the inability to inspect the holes prior to grouting/concreting, and the various installation techniques utilized, quality control for assessing the integrity along the entire length is limited. Currently, quality assurance is conducted by load testing to verify the pull out capacity after installation. The load testing is typically done on a small percentage of the total number of soil nails. This paper will provide the results of a demonstration where the new Non-Destructive Test (NDT) method Thermal Integrity Profiling (TIP) was used to access the integrity of several soil nails along their entire lengths. This TIP method has been successfully used for several years to assess the integrity in drilled shafts and ACIP piles. The TIP method assesses the integrity across the entire cross-section and can identify regions where bulges, necks, and insufficient grout/concrete are present. TIP testing can also help assure that the contractor's installation methods are adequate and consistent for the intended design. For the project presented, instrumented Thermal Wire were affixed to the centered tension bars prior to placement in the excavated shafts. Temperature measurements were recorded from the hydration energy generated after grout/concrete placement, capturing the entire heating cycle. Manufactured defects were installed on the center bar at multiple locations. The results and conclusion will be discussed as well as recommendations for future use.

Jan 1, 2017

By F. H. Nehl

Ion elutriation was used to extract silver cyanide complexes and free cyanide from aqueous streams containing up to 10 ppm silver and 5 ppm free cyanide. Screening tests selected nine of 350 different surfactants for further, larger scale experiments. The screening procedure used 0.1 g of each of the surfactants in 300 mL of synthetic wastewater. Air was sparged into the test cell at 50 cc/min. The foam was refluxed during the tests and was not sampled. Samples of the solution were taken at specified intervals and analyzed by wet chemical methods for free cyanide and by atomic absorption for silver content. The most effective surfactants lowered the silver and free cyanide concentrations to less than 0.5 ppm in 1 h or less. These surfactants were quaternary amine salts with one long chain (C12-C18) organic group and three methyl groups. Experiments using 3 L batches of wastewater or an ion elutriation cell continuously fed with solution draining from an inactive heap leach operation confirmed the results from the screening tests.

Jan 1, 2010

By Charles D. Litton

This U.S. Bureau of Mines report describes the results of two large-scale tests conducted to evaluate a prototype nitric oxide (NO)-compensated carbon monoxide (CO) fire sensor, developed by Carnegie Mellon Research Institute (CMRI). In the tests, small coal fires were allowed to develop in the presence of diesel exhaust at relatively low ventilation airflows. These tests compared the response of the CMRI fire sensor with that of other fire sensors, including the Bureau's diesel-discriminating smoke detector. During the tests, CO, NO, and smoke levels were continuously monitored in order to determine the sensor alarm times and gas levels as the fire developed. The data indicated that the NO-compensated CO fire sensor was capable of suppressing the CO produced by a diesel engine and that the sensor responded reliably to the CO produced from the test fires. The tests also showed that the Bureau's diesel-discriminating smoke detector alarmed earlier than the prototype NO-compensated CO fire sensor.

Jan 1, 1993

By Raj K. Rajamani, Nikhil Dhawan

"Agglomeration has become common pre-treatment step to improve heap leach percolation thereby recovery, the fundamental understanding of the agglomeration process for crushed ores is still lacking. Agglomeration is required for ores which either contain excessive amounts of clay or an excessive quantity of fines generated during mining and crushing. Numerous experiments have been carried out in laboratory scale batch drums using different ores. It has been found out that experimental agglomerate size distributions exhibit self-preserving spectra. The self-preserving/ similarity distribution of the agglomerates is found to be independent of operating conditions and is uniquely determined by the size enlargement mechanism. An empirical model based on the absolute difference between moisture applied and optimum moisture was developed. This model uses self-preserving spectra in the form of a Rosin-Rammler distribution function to predict size distribution at different operating conditions. The empirical model was considerably easier to work with plant scale agglomeration drums. Also, a test known as dip test is developed which improves fundamental understanding of the agglomerate formation and growth mechanisms. This test also provides the progeny size distribution of each agglomerate size. The progeny size distribution was analyzed with a model that partitions the particles into a host and guest category. The ensuing partition coefficient identifies the behaviour of a particle as a host for other particles or a guest layering on other particles. This concept helps in identifying the type of agglomerate that would result for a specific feed size distribution. INTRODUCTIONHeap leaching is one of the hydrometallurgical processes that have served as a green and economically viable process for the treatment of low grade complex ores of copper, uranium, nickel, silver and gold (Dhawan et al., 2013). Heap leaching appears to be a favorable candidate for the least energy consuming process for low grade ores. In heap leach operations nowadays a pretreatment step known as crushed ore agglomeration has been implemented (Dhawan et al., 2013). A bed of agglomerates improves the uniform percolation of solution through the heaps of ore. Therefore, it was possible to treat wastes and mill tailings via agglomeration and heap leaching. Agglomeration pretreatment is required for ores which either contain excessive amounts of clay or an excessive quantity of fines generated during mining and crushing (Bouffard, 2005; Dhawan et al., 2013).While agglomeration has become common practice pretreatment step in heap leach operations, the fundamental understanding of the crushed ore agglomeration process is still lacking. The author reviewed publications up to 2012 on the crushed ore agglomeration process and did not come up with modeling studies on the topic (Dhawan et al., 2013). Some of the possible reasons can be the stochastic nature of the process, experimental difficulties, and lack of instrumentation for fundamental studies."

Jan 1, 2016

By C. A. Stewart

I. INTRODUCTION AND GENERAL STATEMENT OF RESULTS. The field-work upon which this paper is based was done in the summer of 1910, and was made possible by the courtesy of the Imperial Copper Co., which gave me access to its property. For their kindness in this respect I wish to express my thanks to W. F. Staunton and Meade Goodloe. Moreover,. B. F. Smith and G. B. Gentry, mining engineers in the employ of the company, gave invaluable assistance by placing maps,. etc., at my disposal, and by discussing with me the problems of the district; and it is a great pleasure to acknowledge this indebtedness to them. In order that the significance of some of the details that follow may be better appreciated at first reading, a general outline of the conclusions reached is given here. In the Silverbell mining-district a series of Palaeozoic limestone blocks is completely surrounded by post-Palaeozoic igneous rocks, intruded in the following order: alaskite, alaskite-porphyry, biotite-granite, andesite, and quartz-porphyry. The biotite-granite is believed to represent a differentiation of the. magma from which the alaskite-porphyry came ; and this conclusion-has an important hearing on the origin of the ores. The intrusion of both alaskite-porphyry and biotite-granite was followed by the emission of magmatic waters, which sericitized and silicified the alaskite-porphyry and granite, and produced in the limestone, by the addition to it of silica, iron, and alumina, great masses of garnet, quartz, and wollastonite. Following close upon these solutions came metal-bearing magmatic waters, which impregnated porphyry, granite, and alas kite with cupriferous pyrite, and deposited in the garnet zones chalcopyrite and copper-bearing pyrite that make important bodies of contact-metamorphic ores. Secondary enrichment has taken place in the disseminated ores in the igneous rocks,. raising their copper-content to 2 per cent. in some cases,. and extensive drilling has been undertaken to block out these deposits. East of the contact-metamorphic deposits there is a fissure-vein of lead-silver ore in the quartz-porphyry. This rock is distinctly younger than the alaskite-porphyry and the granite; and the lead-silver ores belong, therefore, to a period of mineralization distinctly later than the copper-deposition.

May 1, 1912

By Marius R. Campbell

Does mine-sampling show the commercial value of a coal, and if so, how should it be done? This question is often asked, but seldom answered. During the past summer, while engaged in securing coal for the Government coal-testing plant at St. Louis, I had an excellent opportunity to obtain information on this subject, and the results seem to furnish an answer to the questions propounded above. Sampling for the Geological Survey Coal-Testing Plant. In organizing the work of the testing-plant, it was decided that coal in car-load lots only would be accepted for testing, also that this coal should be loaded under the immediate supervision of a representative of the plant, so as to be certain that the car-load sample would be representative. As an additional check on the work, two mine-samples were to be collected from each mine visited, and these samples, as well as the sam¬ple from the car when it was received at the testing-plant, were to be carefully analyzed at the chemical laboratory, which was established in connection with the plant and operated under the direction of Prof. N. W. Lord, of the Ohio State University, Columbus, Ohio. Mine-Sanmhling:-Mine-samples were collected with great care by me and my assistants, Messrs. J. Shober Burrows, John W. Groves and Frank W. De Wolf. The dominant idea in the regulations which were adopted for mine-sampling was that it should be done in such a manner that the sample would have the same composition as the commercial output of the mine. .

Sep 1, 1905

By Michel Ruel

"This paper describes how to make advanced control choices when difficult processes need improvement. The decision-making process involves choosing between a rules-based approach and a model-based approach as well as weighing benefits and drawbacks, complexity and simplicity, investment and results. This paper will present briefly each solution: basic control, advanced regulatory control, model predictive control, and expert systems such as fuzzy logic controllers and neural networks. The article then proposes a decision tree for selecting the most appropriate approach. A table will compare usage, development, commissioning, maintenance and lifecycle costs for each approach. Finally, conclusions and suggestions will summarize the methodology.INTRODUCTION Advanced process control (APC) is a popular topic. How can one decide whether advanced control should be added to an existing system? Advanced control is used to improve performance, stabilize production, handle constraints, protect equipment and manage grade changes. Most plants use feedback controllers, usually PID (proportional, integral, derivative) controllers. It is common to develop special control schemes to handle more complex processes. In classic PID process control, a controller brings a single value close to a set point using a single manipulated variable. On the other hand, APC brings several values close to optimal targets simultaneously using several manipulated variables. APC's four main strategies are advanced regulatory control, model predictive control (MPC), fuzzy logic and neural networks. Simple solutions are always preferred. Complexity will be increased if performances (production, quality, etc.) are below par. Profitability analyses should be conducted to validate project viability. Needs—not trends—should dictate choices! Before increasing complexity, it is important to define needs, goals, technical support, budget, etc. All these approaches entail strengths and weaknesses. Building a project based on technology rather than needs spells trouble."

Jan 1, 2014

By S. J. Lötter

Analysis of the major and minor components of raw zircon as well as plasma-dissociated zircon was undertaken using inductively coupled plasma optical emission spectroscopy (ICP-OES). Microwave-assisted acid extraction as well as flux fusion using lithium tetraborate were investigated as digestion methods. Microwave-assisted acid extraction samples were analysed with matrix-matched standards. The most successful microwave-assisted acid extractions yielded 44.3(1), 49.75(7), 78.3(3) and 90.0(7) per cent recovery for Zr, Hf, Al, and Fe respectively using sulphuric acid. In no instance was acid extraction capable of complete digestion of the sample matrix. A standard addition method was applied to the flux-fusion samples due to the high complexity of the sample matrix. Method validation for the flux fusion procedure was performed using the SARM 62 certified reference material (CRM) with acceptable recovery ranges being based on the 95 per cent confidence intervals of the CRM. Successful analyses were achieved for Zr, Hf, and Ti with apparent content of 66(6), 1.7(1) and 0.15(1) per cent respectively.

Jan 1, 2012

By S. A. L. Read

"The intact rock constant, mi, is one of the three basic input parameters required for the widelyused Hoek-Brown failure criterion. Values for the constant should ideally be determined by statistical analysis of laboratory test data. In this paper the influence of the inclusion or exclusion of tensile test data on derived values is discussed. We firstly investigate the relationship between direct tensile strength (DTS) test values and Brazilian tensile strength (BTS) test values based on a literature search, finding that the correlation between the two test types is DTS = 0.9*BTS, independent of the lithology being tested. Secondly, using the shear strength database of Douglas (2002), we examine the influence of confining pressure range and the inclusion or exclusion of DTS and BTS test values on calculated values of mi.Chief amongst the influences was the exclusion of tensile data in the calculation procedure, particularly when the Hoek triaxial confining stress range requirement (?3?max = 0.5?c) was not satisfied. Based on a reasonable 1:1 relationship between R (the ratio of unconfined compressive to tensile strength), use of actual tensile data in the calculations for the Hoek brown failure criterion is considered to be a simpler and more robust approach to the use of a tensile cutoff based on empirical criteria such as that of Fairhurst (1964). We advocate the fitting a failure curve using compressive and tensile test data as the most reliable means of calculating mi, while at the same time satisfying requirements as originally advocated by Hoek relating to the appropriate triaxial confining stress range (?3?max = 0.5?c) and sufficient (>5) evenlyspread data points. In the absence of triaxial data the use of R provides a practical means of obtaining estimates of mi that are more robust than guideline values."

Jan 1, 2015

By Onder Guney, Erdem Demirkesenm

"In this study, the crystallization behavior and thermal expansion coefficient of a lithium disilicate (LS2) based glass-ceramic derived from SiO2-Li02-AhO3-K2O-ZrO2 system was investigated by using x-ray diffraction (XRD), high temperature x-ray diffraction (HTXRD), differential thermal analysis (DTA) and dilatometer techniques. Analytical reagent grade chemicals were chosen as raw materials for preparing glass batches. Nucleation and crystal growth heat treatments were planned according to DTA results. The amounts of the amorphous and crystalline phases developed during the heat treatments were determined by quantitative XRD. XRD results of crystallized samples showed simultaneous formation of lithium silicate (LS) and quartz in the early stage of the crystallization followed by formation of lithium disilicate (LS2) at higher temperatures. The thermal expansion coefficients of glassceramics were also measured depending on the applied heat treatments.IntroductionSignificant developments occurred in all ceramic materials provide the fabrication of high quality dental implants [1]. Glass ceramic based dental restorations like dental inlays, crowns, bridges and veneers are becoming increasingly popular with their reliable and durable performance [2,3]. In addition to their advanced functional properties, glass ceramic implants especially lithium disilicate glass ceramics also face the esthetics expectations of patients and dentists and in this way they are starting to take the place of metal based restorations today [1,3,4,5]. Lithium disilicate glass-ceramics derived from multicomponent glass systems have some superior mechanical and optical properties comparable to natural teeth [ 6]. In restorative dentistry, mechanical characteristics of biomaterials play very crucial role in order to resist the masticatory forces occurred during biting and chewing [7] According to three point bending test results of Roland, flexural strength of the lithium disilicate glass-ceramics were 400±40 MPa and their fracture toughness (K1c) are approximately 3,3 MPa m112 [2,6]. In addition to high mechanical strength, aesthetic appearance is another important prerequisite as material for dental restorative applications. Translucency and light transmission of the LS2 glass ceramics mimic enamel. Moreover, opacity of the material can also be adjusted depending on the restoration types [2,6, 7]. These superior properties of the LS2 glass ceramics are directly related with chemical composition of the base glasses and controlled crystallization heat treatments [ 4, 7]. The aim of the present work is to determine the effect of heat treatment schedules on the crystallization behavior and thermal expansion of the LS2 glass-ceramics."

Jan 1, 2011

By L. R. Burdick

This paper presents a review of published investigation dealing with the importance of sulfur compounds in the deterioration of materials or providing some basis for estimating the extent of loss shareable to such air pollution. Materials included are cement, stone, metals, paint, leather, paper, sand cloth. The investigations may be divided into two classes, one of the laboratory type in which the sulfur content and the humidity of the air were controlled and the other dealing with the exposure of materials to atmospheres not under control. The first type of work has shown that cement is subject to deterioration by the action of sulfur dioxide gas. The experiments with stone indicate that although limestone takes up sulfur dioxide, from the air, moist sulfur dioxide-air mixtures alone cannot be used for establishing- the comparative weathering- qualities of the different types of stone by accelerated test methods. Laboratory tests indicate that sulfur compounds in the air accelerate the corrosion of iron, steel, zinc, copper, and nickel at normal air temperatures and at certain relative humidities. It has also been indicated that certain types of paint are, affected by high sulfur dioxide concentrations, and that paper is attacked by sulfur dioxide in the atmosphere. The investigations of the second type show the amount or variation of corrosion in different localities and under different types of exposure. The investigations (10) (18)4/ during which sulfur determinations were made indicate that sulfur dioxide is a main controlling factor in the corrosion of iron and steel but according to Quick (18) may not be for some nonferrous metals. In general, the laboratory tests do not Jive definite data on the loss due to sulfur compounds at the concentrations normally found in the air. The data from atmospheric exposures are not complete from the standpoint of the exact effect of the sulfur compounds. Damage to materials so exposed is affected by factors such as other chemical contaminants, humidity, rainfall, solid deposits, and sunlight. A simple scheme has been devised in Great Britain which is considered to provide a measure of the attack of sulfur compound, on building materials (1). Small cylinders coated

Jan 1, 1939

By Frank G. Horino

This report describes an instrument designed by the Bureau of Mines for quantitatively identifying texture of rock surfaces produced by grinding or extremely rough surfaces beyond the range of commercial surface measuring instruments. The transducer for the instrument is a linear variable differential transformer that converts mechanical motion caused by surface roughness, waviness, and lay to an electrical output. The electrical output is recorded graphically as an X-Y plot of the line traversed on the rock surface. Details of the synthesized device and its calibration are given. The sensitivity of the unit is 2 percent of the scale setting of the amplifier. The horizontal scale is adaptable from ¼ inch to 15 inches of specimen length with a sensitivity of 0.01 inch if a 10 to 1 magnification is used and 0.1 inch if a 1 to 1 magnification is used.

Jan 1, 1968

By Peter Ay, Vincenz Mehlstaubl, Satyanarayana Narra

"This study gives an insight into non-destructive testing methods suitable for porosity analysis at a small scale, firstly summarizing relevant state-of-the-art technology and pending patents, secondly realizing and documenting the start-up of the VHX-2000 digital microscope by the manufacturer Keyence and thirdly demonstrating practical application with the extended analysis of three fundamentally different agglomerates for which important application-related parameters are determined. Various analysis procedures on the different agglomerates the efficient and timesaving operational features of the digital microscope are outlined. Firstly an analysis of flax fibre agglomerates determines the process conditions best suited to produce agglomerates with specific properties by determining sphericity, cubicity, density and porosity as well as fibre damage and alteration. Secondly the production of iron-hydroxide - hemp-fibre agglomerates serves to obtain information on porosity values as a result of a cauterization of the fibres. The third analysis provides estimations of porosity values for acid-treated lignin agglomerates. Measurements were carried out with compact dry agglomerates and with soaked, expanded agglomerates, determining factors for total water carrying capacity. Practicability of non-destructive testing by digital microscopy is demonstrated and explained concerning the applications in this study by obtaining definite structural findings about the analysed agglomerates. Information on its operation is made available by a practice-oriented manual for the VHX-2000 digital microscope. Further suggestions for more in-detail analysis results with different instruments are given."

Jan 1, 2014

Between 1985-1986, the Bureau of Mines reviewed the mining history and minerals information for areas in and near the San Isabel National Forest to appraise the mineral resources present and determine the types of deposits, and their location in the Forest, that could be mined economically if sufficient demand and metal prices existed. The two major metallic deposit-types that are of national mineral resource significance within the Forest are stockwork- molybdenum (with tungsten and tin) and carbonate-replacement zinc-lead-silver deposits. Historically, small gold placers, gold-quartz veins, silver-quartz veins, skarn iron and copper deposits, volcanogenic copper-zinc-precious metal deposits, and base- and precious-metal veins have been mined. Barite, carbonate rocks, gypsum, other non-metallic deposits, and pegmatites, have also been mined. Sand and gravel, present in large volumes, occurs along and has been mined outside the Forest along the upper Arkansas River valley. Turquoise and gemstones are present in small amounts and are of interest to collectors and jewelers. Geologically, sediment-hosted uranium and copper are present in small occurrences but no resources have been identified. Geothermal resources are related to the Rio Grande rift which parallels the central part of the Forest. Four hot spring areas are present - two of these are within the Forest. Because of the low power requirements of the region, and the presence of other generating facilities, these geothermal resources have had only limited local use. Evaluation of mine models that may be found in the region show that base-metal deposits require a high precious-metal component to be economic. Although molybdenum can be produced at economically competitive prices, there is little demand for the product. Capital costs to start new molybdenum mines would be very high and it is not likely that new mines will be put into production in the near future.

Jan 1, 1989

By E. A. Martell, K. S. Sweder

INTRODUCTION Lung cancer in uranium miners has been attributed to alpha irradiation of basal cells of the bronchial epithelium by radon daughters, primarily by 7.7 MeV alphas from polonium-214 (Altshuler et al., 1964). It also has been was observed that for a given cumulative radon progeny exposure, uranium miners who smoke cigarettes have an incidence of lung cancer about 10 times higher than nonsmoking miners (Lundin et al., 1969). It has been pointed out that the large excess of lung cancer deaths among smoking uranium miners is a multiplicative effect (Doll, 1971), which suggested possible synergistic interactions between airborne radon progeny and cigarette smoking. Experimental studies of the complex pattern of interactions between radon progeny, cigarette smoke particles, and the cigarette smoking process are in progress in our laboratory. Preliminary results, reported elsewhere (Martell, 1981), implicate alpha radiation from indoor radon progeny in the etiology of lung cancer in all cigarette smokers. Cigarette smoking produces high concentrations of smoke particles of low mobility and respirable size--particles between 0.5 and 4.0 µm in aerodynamic diameter (see below). The attached fraction of indoor radon progeny is highly dependent on the air concentration of small particles from cigarette smoking and from other combustion sources (Martell, 1981). The size distribution and other properties of radon progeny associated with cigarette smoke particles enhances their effectiveness in the induction of bronchial cancer in man. In this paper we discuss the properties of radon progeny associated with cigarette smoke, the fractionation of radon progeny and modification of their aerosol properties in burning cigarettes, the role of 218Po in these processes, the production of insoluble 214Pb and 212 Pb enriched particles in burning cigarettes, and the consequent differences in the patterns of polonium isotope alpha irradiation in the bronchial epithelium of smokers. EXPERIMENTAL PROCEDURES Experimental methods used in these studies involve the use of small experimental chambers of known radon and radon progeny concentrations in combination with aerosol collection and sizing techniques and sensitive radioactivity detection methods. The use of low-level [ß-] counting for radon progeny determination, providing a measure of 214 Pb plus 214Bi activity, makes it possible to carry out chamber experiments with small radon emanation sources and relatively low air concentrations of radon and radon progeny concentrations in the range from 100 to 1,000 pCi per liter. Thus, for example, in a typical experiment we use a 10 nanocurie 226Ra solution standard in a 10 liter chamber, providing an equilibrium concentration of 1,000 pCi of radon per liter. In small sealed chambers, radon progeny plate out rapidly on the chamber walls, with steady-state concentrations of airborne progeny less than 2 percent of equilibrium levels. This is experimentally convenient because, upon introduction of high concentrations of cigarette smoke particles or small particles from other sources, there is a systematic ingrowth of attached radon progeny, providing a tagged aerosol source of known age and radon progeny composition. In some chamber experiments a 226Ra solution standard of small volume, acidified to O.1N HNO3, was used as the radon emanation source. When used with a bubbler the holdup of radon in an 8 ml volume of 226Ra solution standard at 0.1N HN03 was only 2% of the total radon in the chamber at equilibrium. For experiments with 212Pb-tagged aerosols, we used a dry Ba(228Th) stearate emanation source prepared by the method of Hursh and Lovaas (1967). 226Ra and 222Rn determinations were made by radon gas counting. The 222Rn in a sealed air or water sample is transferred, using helium gas as a carrier, successively through a dry ice cooled trap at -80°C to remove water, through ascarite to remove C02, and through a small activated charcoal trap at -80°C to collect the 222Rn. Subsequently, by heating the charcoal to 400°C, the 222Rn is transferred next to an LN2-cooled capillary trap, and finally into an alphascintillation counting cell of the type described by Lucas (1957). As already stated, radon progeny activities were determined by low-level [ß-] counting, which provides a measure of 214Pb plus 214Bi. The radon progeny samples, collected on efficient Delbag polystyrene micro-fiber filters or on impactor foils, are placed in close, sandwich geometry between two thin-walled flow counters inside shielding anticoincidence counters and a 15 cm thickness of steel shielding. This configuration provides nearly 4II geometry and a low background of only 0.25 to 0.30 cpm. Aluminum absorber was added to provide a combined thickness of absorber and counter wall exceeding 7.0 mg/cm2 to eliminate the variable contribution of 7.7 MeV alphas from 214Po. 212 Pb determinations also were carried out by low-level [ß-] counting, in this case using a combined absorber and counter wall thickness of 9.0 mg/cm2 to eliminate contribution of 8.8 MeV alphas of 21 Po. In each experiment the [ß- ]activity data were corrected for decay to an appropriate common reference time for assessment of activity distributions.

Jan 1, 1981

By Timothy P. Smirnoff, Arthur P. Chase, Herman J. Smith

INTRODUCTION The Newtown Creek Pollution Control Project (P.W. 53) is a major system of facilities designed to collect wastewater from large areas of the Boroughs of Manhattan, Brooklyn and Queens, then channel it to a treatment plant where the wastewater is processed and discharged. The North Branch interceptor collects wastewater along the east side of Manhattan and transports it downstream to a Junction Chamber at Avenue "D" near East 13th Street. The South Branch interceptor similarly collects wastewater from the southern part of Manhattan Island on both east and west sides of Manhattan and transports it to the same Junction Chamber from where both flows are delivered to the adjacent Manhattan Pumping Station which pumps the wastewater under the East River to a treatment plant in Brooklyn. This system is shown in Figure 1. Construction of the Manhattan Pumping Station began in the Summer of 1966 and was delayed by a number of mishaps. In the vicinity of the North and South Interceptors, approximately 3,060 cubic meters (4,000 cubic yards) of soil flowed into the excavation: 765 cubic meters (1,000 cubic yards) at the North Branch Interceptor, and approximately 2,300 cubic meters (3,000 cubic yards) at the South Interceptor. These movements were accompanied by surface subsidence, collapse, or both. On June 4, 1973, while pumping station construction was underway, approximately five to seven cubic yards of sand entered the junction chamber through a temporary bulkhead valve in the North Branch Interceptor.

Jan 1, 1979

By W. S. Landers

Nine high-volatile bituminous Utah coals were carbonized singly and in blends with low-and medium-volatile bituminous coals. Of the 9 coals, 2 are in commercial use as the base coals in blends that produce industrially accept-able metallurgical coke, while 7 are regarded as weakly coking and are not used commercially in coking blends. The carbonization tests were made in a la-inch diameter, cylindrical retort, using 50-pound charges. Sunnyside coal blended with autogenous char generally produced larger and stronger coke than was yielded by straight Sunnyside coal. The volatile matter of the char and the concentration of the char in the blend appear to be important parameters influencing coke size and strength. A blend of 10 per-cent autogenous char of 7.2-percent volatile matter with Sunnyside coal yielded coke that was larger, stronger, and of higher apparent specific gravity than coke produced from an industrial coke oven blend consisting of 15 percent medium-volatile coal and 85 percent Sunnyside coal.

Jan 1, 1967

By E. B. Kester

In the commercial evaluation of coal tars, a distillation analysis properly carried out is of considerable importance. Close attention must be given to this operation in order to obtain consistent results and to secure the minimum decomposition of the tar compounds, Which in Many cases are sensitive to undue heat effects. Low-temperature tars in particular contain compounds of this nature, while in the case of tars produced at high temperatures the large proportion of pitch present has an adverse influence during a distillation. If excessive cracking takes place, the composition of the distillate will naturally vary from the normal, with the result that all the analytical criteria subsequently obtained are affected. Where tars, produced over wide ranges of carbonization temperatures are investigated as in the survey of gas, coke, and by-product making properties of American coals now being conducted at the United States Bureau of Mines Pittsburgh Experiment Station, the method of distillation must necessarily be the same for all of the tars studied. Also, it mast function equally well for both low and high temperature tar permit accurate fractionation, and reduce adventitious decomposition to a minimum. The authors are aware that certain types of distillation analysis which do not meet the above requirements may give results comparable with those of the large stills of a by-product coke-plant where one type of tar is produced. These may be simpler and shorter and entirely suitable for control work, but at the same time have little value in a fundamental investigation.

Jan 1, 1932

By A. J. Kraemer

This paper is the second and concluding report of the results of the twenty-fourth semiannual survey made by the Bureau of Mines of motor gasoline marketed in the United states. The first report on this 1931 survey gave the results of the examination of the gasoline samples in accordance with the new Federal specification for United States Government Motor Gasoline. The present paper reports results of the examination of the gasolines for color, doctor test gravity, end point, per cent recovered copper-dish gum, and steam-oven gum. The retail price and the tax at the time each sample was taken are also reported.

Jan 1, 1932

By Laurent Dorel

Surface quality monitoring is primarily implemented in the last steps of steel manufacturing before shipment to the end user. However, an increasing trend for also addressing this topic in the upstream stages, such as hot rolling plant, is tackled by Primetals Technologies to give steel producers the key to a global optimized yield management, and efficient “lessons learned” processes. After the last developments of SIAS Next Gen platform, including High Resolution and Near Infra-Red, some site results will be exposed on the very specific high constraints lines such as ESP Endless Strip Production and Plate Mills, and highlights the related most interesting aspects for our customers.

Aug 17, 2017