Search Documents

By Gregory A. Stephan

A case history of design, prediction, instrumented static load tests on probe piles, installation monitoring, and integrity testing of production piles is presented. Based upon project-specific subsoil conditions, as obtained from several 60 to 80 ft (18.3 to 24.4 m) deep test borings, deep foundation system alternatives included driven concrete and steel pipe piles as well as augered cast-in-place (ACIP) piles. High structural loads, site-specific constraints, and the production time frame mandated by the project owner led to the selection of an ACIP pile foundation system that was designed for a pile capacity of 75 tons (667 kN) in compression and 35 tons (309 kN) in tension. Site-specific concerns were raised about the highly porous nature of fragmented and decomposed sandy limestone as well as the high grout intake during construction that could result in increased foundation cost as well as interconnecting of the piles in the rock layer. Consequentially, a multi-phase ACIP pile evaluation program consisting of instrumented compression pile load tests, in conjunction with single-hole ultrasonic pile testing, pile echo testing (sonic testing), as well as full-time production pile monitoring by an experienced geotechnician was specified. As a result of this testing and evaluation program, while grout usage was determined to be within an acceptable range, the instrumented compression load tests yielded data that allowed use of 55 ft (16.8 m) long ACIP piles in lieu of the original plans to use 70 ft (21.3 m) long precast concrete piles. This information was effectively utilized as part of the overall quality control program to install a total of 268, 14 in. (356 mm) diameter ACIP piles within the building footprint to depths of 55 ft (16.8 m) below the pile cut-off elevation as part of the foundation support system. Information recorded during installation included rate of insertion/extraction of the auger, grout pump strokes and pressure, total grout volume, and grout factors, as well as quality and strength of grout. Additionally, many pre-selected installed piles were tested for integrity with a Pile Integrity Sonic Analyzer (PISA) using both sonic and ultrasonic methods. This engineered, monitored, and tested foundation solution provided an effective and quality intensive basis for completion and approval of the foundation work for the building that resulted in cost savings over other foundation alternatives for the owner.

Jan 1, 1999

By Gordon B. Brox, Joseph F. Mcaleer, Charles C. Goddard, Edward P. Shea, Robert G. Ingersoll, Lester G. Zeihen, George J. Burns, John M. Guilbert, Richard N. Miller, Charles Meyer

The Boulder batholith is a composite intrusive in which the Butte quartz monzonite is the dominant rock type. Quartz porphyry dikes intruded the quartz monzonite in directions which were subsequently followed by the eastwest- striking Anaconda system of veins, the earliest major veins in the district. Anaconda veins are faulted by northwest-striking veins of the Blue system, which are most prominent in the central third of the district. Anaconda veins are the major producers in the western third of the district and also in the eastern third, where the "horsetail" zones break off from them. Individual oreshoots are thousands of feet long as well as deep on both systems of veins, but they are generally more persistent and thicker on the Anaconda veins. Viewed broadly, the mineralization in the big veins is arranged in crudely concentric zones of zinc and manganese around a central zone of copper. Only slightly offset from these zones, but earlier structurally, is a zone in which quartz-molybdenite veinlets are prominent. This zone tops at about the 2800 level and widens downward. The pattern of distribution of Cu-Fe-S series minerals in the large veins of the copper zone is not symmetrical with respect to the metal zones. There is a fringe of chalcopyrite-bornite all around the copper front. However, within the copper zone, pyrite-chalcocite-enargitecovellite- digenite assemblages are prevalent near its eastern edge from the 3800 level to the surface, whereas deep on the large Anaconda veins in the western part of the copper zone, chalcopyrite is dominant. Here the chalcopyrite grades upward into bornite-chalcocite ores and eastward into the high-sulfur assemblages of the Leonard mine. Sericite-biotite-K-feldspar alteration envelopes, containing up to about 2 per cent copper as chalcopyrite, are present on some of the quartz-molybdenite veinlets at deep mine levels in the molybdenite zone. These envelopes contrast sharply mineralogically and chemically with the later sericitic and argillic alteration envelopes around Main Stage veins. K'0-Ar'0 ratios indicate that they may be older by about 4 m.y. Secondarily enriched copper ores are mined in the Berkeley pit in the southeastern part of the district. At the present time they account for about half of Butte's production of copper.

Jan 1, 1968

By Robert Stefanko

The results of a recent study on the influence of continuous and conventional mining techniques on the size consist and wash- ability characteristics of coal are presented. Eight samples, four each from continuous and conventional mining sections were collected. Each sample was screened in seven size fractions, and each size fraction was totally fractionated at five gravities. The data thus collected was statistically examined for the influence significance of mining techniques, size, and gravity on the quality of the mined product. The paper presents the sample collection method, data gathering and analysis procedures, and major conclusions. The study revealed that there are pronounced differences in the products from the two mining systems and that conventional mining yielded a better product in terms of size-consist, and yield, ash, and sulfur in both the raw and washed products. The results of the study are significant in regard to consideration of resource utilization and conservation, and environmental impacts.

Jan 1, 1974

Waihi Gold Mining Company Limited, a wholly owned subsidiary of Normandy Mining Limited, operates the Martha gold mine, located in the township of Waihi, New Zealand. The operation, an unincorporated joint venture, comprises Normandy Mining Limited (67.070/0) and Otter Gold Mines (32.94%). Since gold was first discovered at Waihi in 1878, it has formed a key part of the region's economy. In 1909 the Waihi mine was described in a report to Parliament as æthe most important gold mine in Australasia and one of the greatest in the world.Æ That was a record year for production, with 416,813 tons of ore mined and some 1,120 men employed. Today the mine produces up to 1,250,000 tonnes of ore annually, and the project employs some 234 men and women. In 1999 the value of the gold and silver produced ($59 million) made up 47% of Waihi's estimated GDP. Waihi Gold has made significant contributions to the Waihi economy, community and the Hauraki region as a whole. Since the mine was re-opened in 1987, thousands of local people have benefited from the mine. In 1999, consents were granted allowing an extension to the mine life (the Extended Project) and this will result in a further seven years of economic benefits resulting from mining activity. The Company has undertaken extensive consultation throughout project planning, construction, operations and rehabilitation. Ongoing liaison and involvement with all community sectors, including Tangata Whenua and Iwi, local residents, recreational groups and schools remains an integral part of the operation. Throughout the life of the modern Martha Mine, the Company has actively supported the local community in the form of donations, sponsorships, the provision of amenities, and by participating in community events. A well established environmental team exists at the site. Environmental and community performance is measured by an independent five-assessment process, and the Company is committed to achieving excellence through ongoing improvement programmes and staff awareness. When the mine is closed, the open pit area will be transformed into a recreational lake, and the tailings storage facilities will be rehabilitated to become a combination of wetlands, grassed areas and ponds. Resources will be provided by the Mine to ensure the rehabilitated site remains in a safe and self-sustaining, stable condition in perpetuity. The mine is regarded as a showcase on a world standard of how a modem mining operation can successfully coexist with the nearby community.

Jan 1, 2000

By R. W. Bruce, K. W. Downes

"IntroductionSULPHUR production in Canada from all sources for the year 1953 amounted to about 375,000 tons. Except for 16,000 tons of elemental sulphur derived from natural gas, this production was in the form of by-product pyrites, liquid sulphur dioxide, and sulphuric acid. In the same year, Canadian industry imported 359,000 tons of elemental sulphur from the United States. The cost, including transportation charges, to Canadian consuming plants ranged from $35.00 to $45.00 per long ton, depending upon location.Although most of the sulphur consumed is used in the oxidized form it is often most convenient to buy sulphur in the elemental form, and convert it to sulphur dioxide or sulphuric acid in situ as required. This is because elemental sulphur is easily shipped and stored, weighs only half as much as an equivalent quantity of sulphur dioxide and one-third as much as the corresponding quantity of sulphuric acid, and is readily converted to these forms in a sulphur burner. A process, therefore, which could economically recover elemental sulphur from sulphide ores would be most attractive.Since the turn of the century, notable improvements have been made in extractive metallurgy, but until recently only limited attention has been paid to the possibilities of elemental sulphur recovery. This has been due to the plentiful supplies of cheaply mined Frasch sulphur which have been available on the world markets."

Jan 1, 1955

By Cyril Stanley Smith, Earl W. Palmer

A STUDY of the precipitation-hardening of copper steels1 led the authors to investigate malleable iron containing copper, for the low-carbon ferritic matrix in malleable iron should lend itself admirably to precipitation-hardening. It was soon found that in addition to rendering malleable iron susceptible to improvement by precipitation-hardening treatments, copper has another potentially useful effect as an accelerator of graphitization. Brief mention of these effects was given in a general paper by Lorig and one of the present authors2; the present paper gives further details on the graphitization and precipitation-hardening effects only. After the completion of this work a paper by L. Lykkin3 appeared, confirming the authors' conclusions regarding graphitization. MATERIAL USED After some preliminary heats had been made in the laboratory to determine the effect of copper, several castings from commercial air-furnace heats were obtained, and data from these alone are given here. Part of the metal was poured directly and part was treated in the ladle with the desired amount of copper before pouring. Green-sand molds were used, each holding two tensile test pieces of the form adopted by the Malleable Iron Research Institute, or two bars for graphitization studies, 5/8 in. in diameter and 9 in. long, fed through two enlarged sections equidistant from the middle and ends of the bars. Risers of suitable size insured sound castings. Tensile tests were made

Jan 1, 1935

By R. C. Gabler

Effective recycling or disposal of flue dusts is a continuing problem, particularly for secondary smelters treating low-grade Cu scrap. The Bureau of Mines investigated a variety of flue dust treatment approaches and demonstrated the technical feasibility of a bench-scale alkaline method that includes leaching, cementation, precipitation, and roasting. Flue dust was leached at room temperature with an alkaline solution of (NH4)2C03 and NHpH to solubilize ZnO and Zn metal. Some copper, lead, tin, and most of the zinc were dissolved in the leach step. Copper, lead, and tin were recovered in the cement product. The Zn in the flltrate was precipitated by pH adjustment to neutral using CO2 injection. The Zn salt was flltered from solution and roasted to give high-purity ZnO. The leach residue, enriched from 4.3 to lOA pct Sn, could find a ready market; the metallic cement product can be recycled back to the copper converter; and the high-purity ZnO product can be sold in several markets, leaving no material for disposal. The possibility for recycling of reagents, lower energy demand, and low environmental impact make this method economically and environmentally attractive for recycling secondary copper smelter flue dusts.

Jan 1, 1988

By D. C. Torre

The need for a successful, efficient and reliable continuous face- haulage .system for use with continuous mining machines has been apparent since the first continuous miners were introduced some twenty-five years ago. Some thought and effort were given to the development of continuous haulage over the last twenty years or so. Some initial success was experienced in this area by The Long Company with a system involving bridge conveyors, as far back as the late 1950's. However, extensive success with continuous face haulage for use behind modern, high product¬ion, continuous miners escaped the industry until the early 1970's. It is true that continuous face haulage was successfully introduced into low seam mining, generally in seams ranging under 1.07 m (42") in height, in the 1960's, for use with relatively low production, low seam, auger type continuous miners. However, those available systems which have achieved success in the lower seams, where relatively low capacities are adequate, are not directly applicable for use with today's medium and high seam miners with their standard production capacity of 9.1 - 10.9 mtpm (10 - 12 tpm). Since the late 1960's and early 1970's, several machinery manufacturers, and at least two major coal companies, have devoted considerable expense, time and effort to developing truly successful continuous face haulage for use in coal seams ranging upward from 1.2 m (4') in height. Continuous face haulage equipment has been developed in the last five years employing a variety of transportation media and design concepts, including some which have received wide publicity such as those employing hydraulics, and pleated belt. The truth of the matter is, however, that the only universally applicable and widely successful continuous face haulage equipment introduced to date has been that employing a combination of bridge conveyors and mobile, self-propelled, bridge carriers, connected at the inby end to the tail of the high production continuous miner, and at the outby end attached directly to the panel conveyor (Fig. 1 & Fig. 2) or, on occasion, to a short, self-contained conveyor which, in turn, empties directly onto the panel conveyor. While these bridge type continuous haulage systems are available with both belt and chain conveyor components, the most widely applied and successful system in seams above 1.07 m (42") in height is that offered by The Long-Airdox Company. The standard unit for use with 9.1 - 10.9 mtpm (10 - 12 tpm) continuous miners is normally equipped with belt. However, they have built, and successfully applied, versions of this system employing chain conveyors, (Fig. 3), mainly for operators having extremely difficult mining conditions, including excessive amounts of water

Jan 1, 1977

By S. Esfahani, M. Barati, Y. Kauwachi

"Heat recovery from slag has gained attention due to its high potential in lowering energy intensity of metal extraction processes. A direct method to recover the thermal energy of slag is to use countercurrent air flow that extracts the heat from falling droplets. Often, the solidified slag is aimed to be used as a substitute for Portland cement, thus high cooling rates are required to form an amorphous slag with sufficiently strong hydaulicity. Rapid cooling however involves using large gas flow rates that in turn lower the thermal efficiency of the process. This article presents a mathematical model that was developed to determine the optimum conditions in the heat recovery process and to investigate the effect of the air flow and granule diameter on the cooling rate of the droplets as well as the thermal efficiency of the heat recovery system. INTRODUCTIONMetallurgical slags are the largest by-product of high temperature materials refining and extraction processes. The total amount of metallurgical slag produced in the year 2008 has been estimated at up to 422 million tonnes containing up to 222 TWh/y (Barati and Esfahani, 2011) of thermal energy. Over the past four decades attempts have been made to recover this substantial amount of energy as heat, electricity, or fuel, while none of the proposed method has been commercialized yet.During slow cooling the slag tends to crystallize the constituents (CaO, SiO2, Al2O3, etc.) into a hard, heavy solid. In the past, over 90% (Bengt, 1983) of the molten waste was discharged onto heaps and allowed to cool slowly, then crushed and used in road construction or land filling or as coarse aggregate for concrete. However, later it was found if cooled rapidly, the slag can be used as a substitute for Portland cement. As a result, processes such as wet granulation were created in which molten slag is fragmented with water, forming amorphous (glassy) phases. Despite its effectiveness in producing a suitable material, heat would not be recovered through this process. Thus, dry granulation was introduced in 1930’s and was developed further in 1970 – 1980’s."

Jan 1, 2012

By Leonard B. Gulbransen, John R. Lewis, W. Martin Fassell, J. Hugh Hamilton

A simple reproducible method was developed for determining the ignition temperatures of magnesium and magnesium alloys and by this method magnesium and over 100 magnesium alloys were measured. The ignition temperature of magnesium was determined in O2-SO2, O2-N2 mixtures and in O2 from 0.166 to 10 atm pressure. The ignition temperature of magnesium is generally lowered by alloying and increased by an increase in oxygen pressure. WITH the expanded use of magnesium alloys in industry, ignition temperatures are of considerable importance, especially in heat treating and for service at elevated temperatures. Magnesium alloys exhibit a relatively slow linear oxidation rate up to temperatures near the melting point.' At some critical temperature the rate of oxidation becomes extremely rapid. This high rate of oxidation is accompanied by the emission of light and additional characteristics suggesting a flame. The literature concerning the ignition temperatures of magnesium and magnesium alloys is relatively incomplete and the values reported by various authors are not in agreement. The most probable reasons for this are: 1—The absence of a suitable definition of ignition, and 2—the need of a standardized method of determining the ignition temperatures of inflammable metals and alloys. The exact date of the discovery of the fact that magnesium will ignite and burn is unknown. It is likely that H. Davey encountered this property of the metal during its preparation in 1808. The first reference in the literature specifically on ignition of magnesium is by Lenze, Metz, and Rubens.' They investigated the inflammability of certain magnesium alloys. Brown3-' reported that magnesium ribbon will ignite in air at 507 °C by what was called the rising temperature method. Hartman, Nagy, and Brown" reported that magnesium powder ignites from 475" to 560°C depending on particle size. According to Guise, Mars, and Wilson prolonged heating in air at 427°C of common casting magnesium alloy causes it to ignite. Samples of magnesium alloys were placed directly in the flame of a torch by Carapella and Shaw.' These investigators obtained some evidence of melting prior to ignition. For commercial magnesium, they reported an ignition temperature of 650°C. Their values varied from 450" to 800°C for magnesium alloys. Willmore and Peterson" studied the effect of air velocity, humidity, rate of heating, and foreign metal contact on the ignition temperature of magnesium. They conclude that melting is not a prerequisite for ignition and that the conditions which influence ignition are complex and difficult to analyze. The only quantitative theoretical treatment of the ignition temperatures of magnesium and magnesium

Jan 1, 1952

By Ben Q. Li

An efficient numerical algorithm for solving steady state heat transfer and solidification problems is described. The algorithm is of boundary integral type and is based on the formulation of the field variables along the boundary of the domain of interest. Compared with the familiar domain-based methods, such as the finite element and finite difference (or finite volume) methods, this boundary-based method has an advantage of solving fewer unknowns and hence has a potential for reducing computational time significantly. Another and yet more important advantage of the present algorithm is that it is a stable scheme and is not prone to numerical oscillations resulting from convective effects, as often encountered in the domain-based methods. Therefore, no numerical or artificial diffusion (such as streamline upwinding) is necessary. Numerical examples are presented that are drawn from processing systems for producing aluminum-based materials.

Jan 1, 1994

By Earl M. Frizzell, Ronald W. Utley

Introduction For the past several years the Bureau of Mines has undertaken research to develop alternative mine material haulage systems that will improve mine productivity, reduce haulage costs, increase mineral availability, and conserve energy. One basic concept being pursued is a means for crushing primary blasted rock to a size that can be reliably and economically moved on conveyors. During 1980, mine requirements for this equipment and the capability of existing technology to satisfy these requirements were assessed. The study continued into 1981 on the basis that satisfactory equipment for this purpose needed to be developed. The objective of the 1981 program was to perform an engineering design of such a system. A mine survey and equipment development study was conducted in cooperation with the open-pit mining industry by GATX through its subsidiaries, Fuller Co. (a crusher manufacturer) and GARD Inc. (GATX's research and development center), under contract to the USBM. Results of a mine survey in the copper, iron, and molybdenum industries indicated that a universal crusher system could be developed even though details might vary from mine to mine. The crushing characteristics, including tonnages desired, were similar in all surveyed mines. Most mines had similar views about the desirability and frequency of crusher movement. The perceived need for in-nit crushing varied between copper and iron mining. The copper mines felt a greater sense of urgency for introduction of such a system, probably because typically greater vertical haulage is found in copper mines than in the iron mines. All mine personnel surveyed were interested in portable crushers and almost universally preferred gyratory-type primary crushers. They preferred large crushers, citing inherent reliability and durability, and the machine's relative freedom from clogging. Large size minimizes the number of crushers and conveyors needed. Analysis of desired crusher system characteristics (Table 1) fixed the crusher size at 1.5 x 2.3 m (60 x 89 in.). The 1.5-m (60-in.) feed-opening dimension could accept the largest material normally fed to the crusher, and the 2.3-m (894n.) head diameter could fulfill the 3.63 kt/h (4,000 stph) capacity requirement. Selected System Description The comments and analyses discussed in the contract report led to the design and refinement of a movable crusher system. This system represents the consensus of more than 100 mine workers and almost 50 construction and engineering company personnel. It is supported by more than 50 years of experience in crusher manufacturing. Although many alternatives are available for any given system, and selections are likely to be dictated by varying site conditions, the selected system is believed to be appropriate for most projected requirements. Final design would be dictated by mine operators during evaluation for approved projects. Detail design of the feed and discharge systems were not included in the study because they are mine specific. The basic system (Fig. 1) consists of a 1.5 x 2.3-m (60 x 89-in.) gyratory crusher on a structural steel frame. The frame is used as an operating platform for the crusher and as a carriage to move the crusher. The control tower includes a crusher lubrication room, a hydraulic equipment room, a switch gear room, a room for the motor control center, and a control room for operating the crusher and maintaining the equipment. The auxiliary system consists of a hydraulic rock hammer and pedestal crane with 74-t (80-st) and 14-t (15-st) hooks. Figure 1 also shows stairs, railings, and a work platform. Feed and discharge arrangements are shown on Fig. 2. The system shown is for mildclimate applications. Additional enclosure and heating would be needed for extremely cold weather conditions. Crusher A 1.5 x 2.3-m (60 x 89-in.) gyra¬tory crusher was selected for this application. This size can handle the typical throughput of 3-3.63 kt/h (3,500-4,000 stph) desired by the mines and the 1.3-m (50-in.) material to be crushed without difficulty. The crusher is the heaviest

Jan 4, 1983

By A. F. van der Merwe, R-D. Taylor, M. Jacobs, F. H. Conradie

Total bound moisture (TBM) is a typical quality indicator of industrial-grade gypsum. This gypsum is comprised of three distinct phases, namely anhydrite, dihydrate, and hemihydrate, of which only the latter is of much industrial use. TBM analysis is a lengthy laboratory procedure, and an artificial neural network (ANN) TBM inference measurement is proposed as a fast and online alternative. An ANN inference model for gypsum TBM based on plant data was developed. The inputs to the network were primarily focused on the plant's calciner, and different network topologies, data divisions, and transfer functions were investigated. Furthermore, the applicability of the TBM value as a quality indicator was investigated based on a gypsum phase analysis. A strong correlation between TBM and the gypsum hemihydrate and anhydrite content was found, validating the plant target TBM of 5.8% as a quality indicator. A network topology consisting of one hidden layer with logarithmic-sigmoid (logsig) and pure linear (purelin) transfer functions showed the best performance (R > 90%).

Oct 3, 2023

By John A. Johnson

The first report of investigations5/ in this series pertaining to the investigation of stemming at the Mount Weather testing adit dealt with dust produced from blasting. The present report discussed the effect of stemming on eases generated by blasting, describes the test procedure, and analyzes the results from, blasting 61 standard rounds. Following care the types of stemming that are being investigated: 1, No stemming. 2. Sand in 2 paper cartridges. Clay in 2 paper cartridges. Commercial hydrated lira in 2 paper cartridges. 5. Combustible blasting plugs. 6. Ceramic is blasting plugs with clay in 2 paper cartridges.

Jan 1, 1940

By D. H. Ryan, B. Abdul, M. Pernechele, E. Asselin

Hydrometallurgical processing of sulphide concentrates at medium temperature (150°C) produces residues, which contain valuable metals (Cu, Ni) as well as sulphur and iron bearing minerals and phases. The low solubility of iron during the medium temperature processing of sulphide ores can favour the formation of poorly crystalline, nano-scale iron oxide/oxyhydroxide phases. A better understanding of the formation and structure of these iron precipitates may elucidate key factors that would ultimately result in lower valuable metal losses and more stable leach residues. Residues from two medium temperature leach processes were characterized by Mössbauer Spectroscopy. Some portions of the Mössbauer Spectrum were suspected to be linked to jarosite but could not be positively identified as such. There was a broad range of disorder and substitution present in the material and solely attributing it to jarosite proved difficult. Various synthetic jarosites with Cu substitution were precipitated for Mössbauer analysis. These were then characterized by Quantitative X-Ray Diffraction (QXRD), Scanning Electron Microscopy (SEM), Inductively Coupled Plasma Mass Spectroscopy (ICP-MS) and Mössbauer Spectroscopy. The Mössbauer Spectra of the synthetic jarosites is compared with that of the residues from medium temperature (150°C) sulphide concentrate leaching.

Jan 1, 2014

By P. D. Kovscek

The Bureau of Mines has tested a low-thrust water-jet-assisted rotary drill. This work was performed to evaluate the performance of a water-jet-assisted drill operated at thrust levels typical of a handheld manual-thrust operation. Prior work by the Bureau had indicated that using water-jet assist with high-thrust drilling applications would increase drilling rate. Small-diameter holes were drilled in five different types of rock. Thrust and water pressure were varied as the drill rate was monitored. The test results indicate that drilling rates increase with increasing water pressure and thrust. The water jet has more effect on reducing the specific energy when drilling in the harder rocks than in softer rocks. Variation in drill rate for a given rock sample is attributable primarily to the material heterogeneity within the sample. One rock type (Greenwich sandstone) could not be drilled efficiently with the water-jet-assisted drill.

Jan 1, 1988

By Michael J. Brnich

On November 20, 1968, a massive explosion rocked the underground workings of Mountaineer Coal Co.?s Farmington No. 9 Mine in West Virginia. Of the 99 miners who were working in the mine at the time of the explosion, only 21 survived and escaped the mine. This group included eight who were rescued from the Mahan?s Run air shaft. Nearly 40 years after the event, researchers from the NIOSH Pittsburgh Research Laboratory conducted oral history interviews with two of the eight survivors rescued from the shaft. The Farmington No. 9 Mine disaster ultimately led to passage of the Federal Coal Mine Health and Safety Act of 1969 (amended in 1977).

May 1, 2009

By Wenjun Ju, Xiaodong Sun, Jianwei Zheng, Bingding Yi, Zhaorui Ma, Pengfei Jiang, Lingfu Zhu, Yangfa Zheng

The presence of hard roof poses a significant threat to the safety of underground coal mining. In this study, a mechanical model is established for underground stopes to analyze the overburden structure with the advancing of the mining face. It is indicated that the load-bearing arch structure (LBAS) is formed above the stope for roofs with regular hardness, whereas the reversed-basin bearing structure (RBBS) is formed for hard roofs. Compared with the LBAS, the RBBS can induce an additional pressure at the foot of the bearing structure, and this effect becomes less as the distance between the hard roof and stope increases. The ultra-deep borehole hydro-fracturing technique (UHT) is proposed to weaken the hard roof for pressure release, and the associated equipment and procedures are also presented. The UHT is based on horizontal drilling along the axial direction of the roadway in the roof, and then the receding segmented hydraulic fracturing technique is used to achieve the purpose of fracturing (weakening) of the surrounding rocks. Field tests are carried out in 3022 roadway of Daliangwan coal mine in Yulin to assess the developed technique, equipment, and fracturing procedures. To evaluate the fracturing effect, deep borehole stress-meters are installed at different depths of the fractured and un-fractured zones of the roadway, along with hydraulic support pressure sensors placed at the mining face. The results show that compared with the un-fractured zone, the pressure on the wall and pillar sides is lower than that in the fractured zone, and the associated weighting duration and weighting area ratio of the fractured are reduced by 53.23% and 33.59%, respectively. This indicates that the presented UHT can provide a new solution for the prevention and control of mining disasters induced by hard roof failures in underground coal mining.

Nov 2, 2020

By E. E. Carpenter

(San Francisco Meeting, September, 1915) BELIEVING that the results accomplished in the mill of the Churchill Milling Co., Wonder, Nev., during the fiscal year ended Sept. 30, 1914, will be of interest, I am presenting the more prominent facts and figures showing the progress made in treating this ore with especial reference to tonnage, supplies, costs, and extractions. The mill is situated at Wonder, Nev., in the Wonder mining district, 55 miles east from Fallon, Nev., the nearest railroad point. All supplies are hauled this distance by freight teams, this method of transportation having been found more reliable for continuous service than trucks, the price paid for hauling being slightly under one cent per pound. In this mill are treated the ores of the Nevada Wonder Mining Co. ,

Jan 6, 1915

By D. Boldini, R. Lackner, H. A. Mang

ABSTRACT: In this paper, the strong interaction between the hardening shotcrete lining and the surrounding ground in NATM tunneling is investigated by means of axisymmetric analyses, accounting for the three-dimensional nature of the excavation process. The effect of the hydration of shotcrete on strength, stiffness, chemical shrinkage as well as microcracking and creep are accounted for. For the description of the mechanical behavior of the ground, a multi-surface plasticity model is employed. The performed analyses of the excavation process provide insight into the influence of each phenomenon accounted for in the material model for shotcrete on the response of the ground-shotcrete compound structure. ZUSAMMENFASSUNG: In diesem Beitrag soll die Interaktion zwischen dem erhärtenden Spritzbeton und dem Boden auf der Basis axisymmetrischer Berechnungen untersucht werden. Derartige Berechnungen ermöglichen die Berücksichtigung des drei-dimensionalen Charakters des Vortriebprozesses. Die Auswirkung der Hydratation auf die Entwicklung der Festigkeit, Steifigkeit und der chemischen Schwindverzerrungen, sowie das Reißen und das Kriechen des Spritzbetons wurde berücksichtigt. Das mechanische Verhalten des Bodens wurde mittels eines Mehrflächenplastizitätsmodells simuliert. Die durchgeführten Berechnungen des Vortriebprozesses geben Einblicke in die Auswirkungen der Spritzbetoneigenschaften auf das Tragverhalten des Boden-Spritzbeton-Komposits. RÉSUMÉ: La stricte interaction entre le soutènement en béton projeté durcissant et le terrain dans un tunnel creusé avec la NATM est étudiée par des analyses axisymétriques, compte tenu de la nature tridimensionnelle des processus de creusement. Les effets de l’hydratation du béton sur la résistance, la rigidité et la contraction chimique, ainsi que sur la micro-fissuration et le fluage, sont mis en compte. Pour la description du comportement mécanique du terrain on emploie un modèle de plasticité multi-surface. Les analyses conduites mettent en évidence l’influence de chaque phénomène considéré dans le modèle constitutif du béton projeté sur la réponse de la structure composite terrain-béton projeté.

Jan 1, 2003