Search Documents

By Michael. H. Moys, Clayton Bhondayi

An electro-resistive measuring technique developed by the authors was used to study the effects of superficial gas velocity and froth height on froth phase bubble sizes as a function of height above the pulp-froth interface. Flotation tests and the bubble size measurement were carried out in a laboratory mechanical flotation cell that was operated in a pseudo-steady state mode using primary rougher tailings slurry from Lonmin Platinum as feed. The values of intra-bubble impact distances (IIDs) which are the estimates for froth phase bubble sizes obtained from the measurements indicated that as superficial gas velocity was increased, the values of IIDs decreased for the two froth depths tested. Increasing froth height at fixed gas rate resulted in an increase in IID values especially close to the froth surface. Changing froth height and gas rate alters froth residence times; longer froth residence times mean more time for bubbles to coalesce hence larger values of IIDs and vice-versa.

Jan 1, 2014

By J. V. Simmons

Composite rock mass failures involve intact rock material as well as fracture and shear on existing defects. Experiences from open-cut coalmining in the Bowen Basin of central Queensland are that failures of this nature occur suddenly with little warning, and are much more common than classical structurally controlled failures. Geological conditions and mining practices in the Bowen Basin are described. The circumstances of a sample of composite failures are described in detail in the paper. From this experience it appears that several aspects of conventional geotechnical investigation and design practice have not contributed significantly to either predicting or controlling the risks associated with sudden failures. These practices are described as myths for reasons outlined in the paper. On the other hand, the reality seems to be that high initial stresses and stress changes caused by excavation lead by a process of extensional deformation to a critical stress condition within the rock mass, and that sudden collapse follows when that critical stress condition can no longer be sustained. It is concluded that learnings gained from underground excavations in rock may be more applicable to open pit excavations than previously thought, and that the processes of prefailure deformation require more careful study if we are to develop more reliable risk management controls.

Jan 1, 2006

By Henrik Gudbrandsen, Anne Støre, Ana Maria Martinez, Karen Sende Osen, Ole Kjos

The light rare earth metals Nd, Pr, La, Ce as well as some alloys with Fe, are today produced in China by electrolysis in molten fluorides using oxide raw materials. A major challenge is to obtain a good cell operation without de-composing the electrolyte leading to emissions of per fluorinated carbon (PFC) green-house gases to the atmosphere. This work is focused on understanding the fundamental requirements to run the electrolysis cells for DyFe alloy production in an ef ficient and environmental friendly way. Electrolysis experiments was carried out in DyF 3-LiF melts at 1050 °C. A Fe rod was used as consumable cathode and the (consumable) anode was made of graphite. To establish at which anode potential PFC occurred and thus enabling optimisation of the oxide batch feed rate, analysis of the anode gases was performed with Fourier Transform Infrared Spectrometer (FTIR). The produced DyFe alloy was characterised by X-ray Diffraction (XRD), Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray Spectroscopy (EDS).

Mar 1, 2017

By W. M. Myers

Certain minerals possess inherent color and other properties that make them suitable for the pigmentation of paints, mortar, plaster, concrete, face brick, and other materials. Their production is one of the most ancient of mineral industries and their use by primitive man is well known. These natural pigments have some economic factors in their favor, particularly wide geographic distribution, low cost of production, ease of preparation, chemical stability, and permanence in use so that they continue to form the basis of a small but useful industry. When used in paints such pigments act as a filler and supply body and opacity in addition to color. Natural mineral pigments are prepared for the market by the comparatively simple operations of washing, grinding, blending, and calcining. Any one, or all of these processes may be applied to a single pigment. The development of synthetic pigments and the use of by- product materials have introduced competition with the products of nature and are having a growing influence on the economic position of the mined minerals.

Jan 1, 1949

By Ned Baker

This report describes the development, construction and testing of a hydrogen-fueled underground mining vehicle. A hydrogen burning engine and a hydride fuel system, both previously developed, were installed on a modified utility vehicle, together with the necessary controls. In tests and in actual use, the vehicle performance in terms of speed, acceleration, and gradeability exceeded that of the standard, unmodified vehicle.

Jan 1, 1985

By Clarence O. Babcock

Since Vicat in 1833, the width to height ratio of a mine pillar has been taken as the fundamental variable in pillar design. From work in the laboratory by many investigators testing rock, Coal and concrete samples, it has been concluded by some that pillars with a width to height ratio of 10 to 1 are indestructible. It has also been concluded that a constrained core exists within the pillar which increases the pillar strength. The role of the roof and floor, if mentioned at all, is often noted in an incidental way. In the present work on laboratory testing of model pillars on concrete, coal, and rock instrumented with special strain gages, it was concluded that the end constraint and not the width to height ratio is the significant variable in determining the pillar strength. In tests where the end constraint is steel, a large compressive stress is produced on the horizontal plane of the pillar, and this effect increases as the width to height ratio is increased, resulting in an increase in pillar strength. If the end constraint is not steel but something with a small Young's modulus, the state of stress in the horizontal plane may be tensile, increasing as the width to height ratio increases, resulting in a decrease in pillar strength. Related to mining, the results are that a large width to height ratio pillar is strong for strong roof and floor and weak for weak roof and floor. That is, the roof and floor and not the width to height ratio determine the pillar strength. The confined core condition should be verified by testing if large pillars are to be used. If there is no confined core or the pillar is in tension, smaller pillar sizes should be used. The final conclusion is that the geometry alone is meaningless in pillar design.

Jan 1, 1984

By R. G. Graber

Field testing of GPS mining applications has confirmed the technical and operational viability of GPS for precise, centimeter-level positioning in harsh taconite environments. GPS hardware has provided consistent availability exceeding 90%, with precision in certain applications of ± 0.07 foot at 95% confidence levels. Despite these technical successes though, challenges persist in achieving effective GPS integration. These challenges include the acceptance of new job tasks by mine personnel, the capacity of typical mine data communications infrastructure and the need to design GPS interfaces for new mining equipment.

Jan 1, 1998

Atlas Copco, a leading supplier of equipment and services to the mining and construction industries, is consistently pursuing its strategy to offer the most productive and economical solutions by continuously offering new innovative products. These are in most cases developed and tested in close cooperation with demanding end users before Being officially launched on the international market. The demands for higher productivity and improved overall economy have resulted in systems for automation of the drilling cycle and also tools for integrating the Drilling equipment to the production control system used by the customer. In terms of improving the blasted material quality, Atlas Copco has placed emphasis on hole straightness and the need for hole logging and positioning. By applying state of the art Technology to today?s computerized drilling rigs, major steps in improving overall drilling and blasting performance have been achieved. This paper will give some examples derived from the latest development of solutions for the Rotary drilling product line.

Jan 1, 2010

By Hongshuang Di, Tianyu Zhang, Huiqiang Huang

A CMnSiAl transformation induced plasticity (TRIP) steel was used to study the effect of retained austenite on room-temperature mechanical properties. The steel plates with retained austenite were obtained by hot rolling, cold rolling and subsequent continuous annealing. The starting and finishing temperature of hot rolling are between Ac1 and Ac3. Reduction ratio of cold rolling is 75%. The continuous annealing is carried out at different intercritical temperatures. The relationship between work hardening exponent and retained austenite was discussed. The results show that, the Ac1 and Ac3 were much high because of the alloy elements, and the temperature range between them was wide. Due to the high hot rolling temperature, the grains was hereditarily refined as a result of dynamic recrystallization. Annealing at intercritical temperature of 930 ºC, retained austenite with relatively high stability reached a maximum volume fraction of 25%, a maximum total elongation of 30.2% and a best ultimate tensile strength × total elongation of 20.1 GPa·%. Instantaneous work hardening exponent reflects strengthening mechanisms at different strain stages. The TRIP effect of retained austenite is the main mechanism during deformation. With retained austenite of sufficient amount and high stability, continuous work hardening was observed in the tensile specimen of 930 ºC.

Oct 1, 2019

By G. J. Hartman

A presentation of this project was given previously at the SHE Annual Meeting, Denver Colorado February 23-27, 1987. The project concerns the development of in situ recovery of borate products from a deep-seated colemanite deposit in California. The deposit contains some 147 million tons of borate ore containing 6.4% boron oxide (B2O3). This paper involves the numerous changes in the process that has taken place since that first presentation. This paper further explains the reasons for these changes which are primarily environmentally based and secondarily capital requirements related.

Jan 1, 1994

By Harry R. Price, Behrooz Tahmasbi, Charles J. Roarty

The 2,408 meter (7,900-foot) long Middle Rouge Parkway Interceptor Extension varies in size from 1.52-meter (5-foot) to 2.36 meter (7-foot 9-inch) inside diameter. Most of the sewer was constructed in tunnel through fine sands and silts. Piping of these soils through the concrete liner eventually resulted in a loss of soil support, settlement and/or severe distress of the sewer, and the formation of several sinkholes. The repair and restoration was generally performed in the sewer and included cast-in-place concrete, shotcrete, cured in place pipe, soil stabilization, cement grouting, dewatering, and chemical grouting. As a part of the work, temporary pump stations and flow diversions were required to perform the work while minimizing discharges to the adjacent Rouge River.

Jan 1, 2007

By Ronald G. Schmidt

AND SOME RIN UP HILL AND DOWN DALE, KNAPPING THE CHUCKY STANES TO PIECES WI' HAMMERS, LIKE SAE MANY ROAD MAKERS RUN DAFT. THEY SAY IT IS TO SEE HOW THE WARLD WAS MADE. Sir Walter Scott St. Ronan's Well - 1824 In the minds of many, geologic exploration has advanced little since the early nineteenth century. In truth, despite the development and refinement of new and potentially valuable technological tools, the approach or philosophy of the explorationist has received meager attention in professional literature. In many areas, the explorationist relies upon experience, subjective judgement and general intangible inspiration, often traveling together under the misleading pseudonym of "art," in achieving both an exploration plan and in making the myriad day to day decisions necessary to the execution of that plan. Without a solid, objective basis for decisions, exploration under this concept is little more than guesswork largely by intuition, and it is small wonder that many exploration programs flounder in a sea of over-expenditure inefficiency or fail to fulfill their expected goals within the funding which has been provided. From a rational management point of view, such a state of affairs is frustrating and inconsistent with the application of the same scientific principles which are presumed to be the basis for the exploration methods which are used. This somewhat presumptuous point of view cannot be extended as a general condemnation of the many exploration programs which are both technically and economically successful. On the other hand, the

Jan 1, 1968

By A. Bouchard

"Based on laboratory testwork, a two-stage cleaner / re-cleaner circuit with feed regrind was proposed to replace an existing single-stage middling circuit treating a scavenger concentrate at Inco’s Clarabelle mill. In order to effectively transfer the technology and implement the new flowsheet in the plant, an extensive on-site pilot plant campaign was conducted. After demonstrating the improved metallurgy, the two-stage middlings circuit was successfully implemented at the operation.The present paper describes the on-site pilot plant testwork and the plant metallurgical improvement after implementation of the new middlings circuit. The addition of TETA / Na2S03 greatly enhanced the pentlandite selectivity against pyrrhotite and the two-stage cleaning considerably improved the pentlandite selectivity against rock minerals. The improvement was immediate after the installation of the new middlings circuit. Size by size recovery analysis indicated that a finer regrind would further improve the metallurgy of the new two-stage cleanerhe-cleaner circuit and those modifications are in progress at the mill.INTRODUCTIONThe milling operation at Inco’s Clarabelle mill has been described elsewhere (Kerr and Kipkie, 1985; Agar, 1991). While maximizing the recoveries of chalcopyrite (Cp) and pentlandite (Pn), continuous effort has been directed toward improving pyrrhotite (Po) and rock minerals (Rk) rejection. Inco discovered diethylene triamine (DETA) and triethylene triamine (TETA) (Marticorena, et al., 1994) for pyrrhotite rejection. Falconbridge further improved pyrrhotite rejection using DETA and SO2 (Kelebek, et al., 1995). No special technologies are used in the rejection of rock minerals."

Jan 1, 2001

By Nozomu Kotake, Rakshya Shrestha, Ralph Griffin, Stefanos Papadopulos, Jeff Fippin, Sushil Kafle

Direct Power Compaction (DPC) is a deep Vibro-compaction method used for liquefaction mitigation. In DPC, H-beams are used as vibrating rods penetrating deep into the ground, and a vibrating force is applied directly to the tip of these H-beams to densify the loose ground. A characteristic feature of DPC is the use of a flapping plate installed at the base of the H-beam to enhance the compaction efficiency during penetration. In addition, 2-rod and 4-rod type equipment have been developed to improve productivity and enable rapid construction. DPC was selected as the most suitable and cost-effective technique to mitigate liquefaction hazards in two projects in the San Francisco Bay Area, one on Alameda Island and another on Treasure Island. Both sites were capped with hydraulically placed sand fills. Liquefaction analyses indicated excessive liquefaction-induced settlements and large lateral spread without ground improvement. Densification using DPC was performed up to depths of 42 ft to reduce the liquefaction potential of the sand fill to acceptable levels and to allow planned improvements. Cone penetration tests were conducted before and after DPC to evaluate its performance. This paper describes the equipment and process involved in DPC and discusses its application in terms of subsurface conditions and geotechnical design considerations.

Sep 8, 2021

By R. C. Gilmore, J. McMack, G. E. Bogin, J. F. Brune, C. DeRosa

"Researchers at the Colorado School of Mines are designing and building a 1:40 scaled physical model of a fully operational longwall coal mine. The purpose of the model is to minimize the occurrence of methane explosion hazards by testing various ventilation strategies and determining optimal methane sensor placement throughout the longwall face. Fluid scaling factors were analyzed using Computational Fluid Dynamics software Ansys FLUENT™ at both full and 1/40th scales. Researchers were able to identify key scaling factors and subsequently developed suitable flow parameters that would maintain full scale accuracy of flow patterns in the 1/40th model. KEYWORDS Coal, Longwall, Methane, Explosion, Scale Model, Ventilation, Fluid Dynamics, Richardson, Gob, Porous INTRODUCTION Mine ventilation systems are a key component for ensuring a safe working environment by introducing fresh air from the surface and diluting explosive gases and hazardous contaminants. This holds true for longwall coal mines where the emission of flammable methane gas from the longwall face as well as the gob can create explosive mixtures of methane and air. Therefore, an effective ventilation strategy can help mitigate the potential for accidents within a mine. Developing an effective mine ventilation system (MVS) requires a detailed understanding of the physics of gas transport and how this relates to specific geometries and obstructions in the face. Researching this phenomenon requires the development of computational fluid dynamics models capable of simulating fluid flow and methane species transport that can be validated through physical experimentation. Unique site conditions determine ventilation layouts for every coal mine. Researchers have designed a 1/40th scaled physical model of a longwall coal face and adjacent gob that includes movable shield supports and a movable shearer with rotating cutter drums that can be adjusted to a variety of ventilation conditions. The proposed work will address the need for an improved Mine-wide Atmospheric Monitoring System (AMS), and provide the ability to link existing MVS models with AMS in real time. By accurately representing the coal face, the gob area and the mining equipment, gate roads and bleeder entries, the scaled model accurately represents all relevant structures, geometry, and dynamic conditions. A Plexiglas cover allows full optical access for sensor equipment as well as visual inspection of the fluid flow and species transport."

Jan 1, 2019

By G. J. Kipouros, N. Dadvand

"In recent years coatings of alloys have been produced for a wide range of applications including many for wire bonding application. The main characteristic of the baths of electroless plating is the presence of sodium hypophosphite as a reducing agent and also as the supplier of phosphorus. In the electroplating of alloys the Watts bath is predominantly used. This presentation compares the two techniques, electroless plating and electroplating, and discusses the possibilities of cross utilization of sodium hypophosphite in an attempt to formulate baths that eliminate the waste disposal issue related to some components.INTRODUCTIONThe importance of surface characteristics and the linkage of surface coating process to surface characterization has given rise to the evolution of surface engineering. Not only the surface preparation and morphology has become very important to the coating technology but also the knowledge of surface area exposed to the process of coating or corrosion is absolutely essential in ascertaining the behaviour of coatings and their adherence to the substrate. The above concepts are not unknown to researchers involved in the protection of surfaces, particularly metallic, from corrosion and/or erosion corrosion. However, the complexity of the surface defects, roughness, porosity, interconnected porosity and other related factors have contributed to the uncertainty of the true surface area versus the nominal surface area. Therefore critical parameters such as current density and chemical surface intensity although have been studied extensively at the atomistic level by carefully prepared surfaces are very difficult to be determined at the practical scale required during the coating processes.The most pronounced case calling for an understanding the relationship between the surface area and the effective protection is the coating of surfaces of items produced by compression or consolidation of powdery materials. With the advent of nanomaterials and the additive manufacturing through 3D metal printing this issue is becoming more important. Certain experience in this field come from the accumulated knowledge resulted from the attempts to characterize the electrochemical behaviour of powder metallurgy metals and alloys. Powder metallurgy has been a well-established process for half a century on basic metals such as iron, copper and their alloys. Recently the development of powder metallurgy process for aluminum, titanium and attempts to develop powder metallurgy processes for magnesium and its alloys has brought to light another important issue that of the development of coatings on difficult to plate reactive metals such as aluminum and magnesium. Despite of many successes in the development of powder metallurgy alloys the exact characterization of the corrosion behaviour of the coatings and the substrates is difficult to determine because of the unknown morphology of the exposed area i.e. the exact morphology and area of the exposed surface (Samal, 2007)."

Jan 1, 2016

Experimentation was performed on the flotation of apatite and dolomite separately using anionic collectors in the presence of Mycobacterium phlei. Also, the flotation of mixtures of dolomite and apatite in the presence of anionic collectors and in the absence and presence of the bacterium were studied. It was found that M.phlei functions as a depressant for both minerals. However, it functions as a better depressant for dolomite than for apatite. Experimentation was extended to two different Florida dolomitic phosphate rocks. In this investigation a concentrate grade of less than 1.0% MgO was achieved.

Jan 1, 1997

By E. S. Davenport

WHEN annealed carbon, or low-alloy, steels are suitably heated the ferrite (alpha iron solid solution) and the carbide, of which they are composed, react together to form a single solid solution of carbon (and other elements) in gamma iron (austenite). This reaction may begin only at a certain minimum temperature called the eutectoid temperature. The first ferrite and carbide thus to react together do so in definite proportions known as the eutectoid composition. With further heating the original constituent that is present in excess is dissolved in the austenite until exhausted. Whether the excess constituent be ferrite (hypoeutectoid steels) or carbide (hypereutectoid steels) the procedure is much the same, and upon slow cooling the homogeneous austenite expels the excess of either (proeutectoid ferrite or carbide) until the eutectoid composition is reached. Thus the reaction upon heating is strictly reversed upon cooling and accordingly an equilibrium diagram of this process may be constructed. Such an equilibrium diagram concerns itself only with the tempera¬tures involved and with the proportions and compositions of the phases developed under conditions that suffice to permit equilibrium. Specifically it has no concern for the type or mode of distribution of these constituents nor with any extra-equilibrium conditions such as undercooling, which is almost universally encountered in metals. Actually, however, of great importance is the sluggishness toward equilibration caused by the not inconsiderable time involved in diffusion. Thus instead of the theoretical transformation point AE, we find for a certain rate of heating or cooling the use of the designations Ar and Ac (transformation temperature found on cooling and upon heating). These figures obviously have no particular meaning except as measured and expressed for a definite heating or cooling rate, and represent the apparent temperature displacement caused by an inadequate time allowance. In this paper are presented the results of a study of the time required for' the transformation of austenite to ferrite and carbide at a variety of temperatures and also of the time required for the reaction austenite ?martensite at the temperatures at which this reaction occurs instead of

Jan 1, 1930

By Richard Kojo Gabah

Western mining companies are entering an African critical minerals market where access is harder to secure, risk is being priced more sharply, and execution advantages are increasingly decisive. The continent holds significant reserves and production potential of cobalt, lithium, copper, graphite, manganese and rare earths critical to the energy transition, yet Chinese-aligned capital has built a structural edge in access and execution speed. Simply signing narrow offtake agreements to buy output is no longer sufficient. Western firms win when they convert quality orebodies into bankable projects by reducing aboveground risk faster than competitors through integrated infrastructure access, durable fiscal alignment, and credible local value creation. Western mining companies will break into Africa by pairing capital with partnership, building corridors enabling infrastructure and power, designing credible value addition pathways and operating in a way that is politically durable through transparency, community benefit and fiscal terms that share upside in commodity upcycles. This feature article offers a practical playbook for mining executives and investors. The core argument is straightforward. Winning in Africa requires competing on the full system around the mine. Corridors and power, processing pathways, contract durability, community benefit and regulatory execution are now decisive variables in project valuation and capital access.

Mar 1, 2026

Standards And Laboratory Monitoring In Gold Assay Key Components Of Best Practice

Jan 1, 2005