Search Documents

Responsibility for the administration of mineral resources is divided between federal and provincial governments. The paper traces the evolution of mineral policies at both levels of government, from the end of World War II to the present. In the immediate post-World War II years, the emphasis was on supplying the raw material needs of a rapidly growing world economy. Policies favouring growth and development of the Canadian mining industry were instituted during this period. Two decades of uninterrupted expansion (the 1950s and 1960s) ensued. The decade of the 1970s was a turbulent one for Canadian mineral producers. Governments intervened more substantially than ever before. Moreover, the industry suffered from an intense period of competition for resource revenues by the two levels of government. At the same time, far reaching changes were taking place in the structure of world mineral markets. To date in the 1980s, the mineral industry has, perforce, adapted to existing mineral market structures. Mineral policies, too, have shown signs of adapting to the needs of the mineral industry. Whether the resulting mix of policies will permit the revitalization of the Canadian mining sector remains to be seen.

Jan 1, 1986

By R. Rocca, M. B. Bever

THE adiabatic elastic deformation of a body is accompanied by a change in temperature. This phenomenon is known as the thermoelastic effect. Under adiabatic conditions the temperature of a metal bar is decreased by an elastic elongation and is increased by an elastic compression. All materials which elongate on heating behave in this manner. The sign of the thermoelastic temperature change is reversed for the few materials which have a negative coefficient of thermal expansion. The following equation for the thermoelastic effect can be derived from fundamental thermody-namic theorems, as shown in the Appendix: dT8 =-a1/cs T dss [1] Cs In this equation, T is the absolute temperature, S is the entropy, a, is the coefficient of linear thermal expansion, cs' is the heat capacity per unit volume at constant stress and s is the stress (positive in tension). Eq 1 can be applied to small, but finite changes in stress in the following form: ?Ts =- a1/cs T?ss [2] The sign of the temperature change AT is opposite to that of the change in stress s for materials which have a positive coefficient of thermal expansion. Eq 2 has been verified for many different materials and stresses at room temperature. No previous publication appears to have been devoted to an in- vestigation of the thermoelastic effect over a range of temperatures. Review of Literature Lord Kelvin (W. Thomson) presented a general theory of the thermoelastic effect in 1851' and later applied it to a solid, subject to an arbitrary system of stresses'. His analysis was based on a cycle of isothermal and constant-strain transformations and led to Eq 2 above. Even today, one of the clearest expositions of the thermoelastic effect is found in Lord Kelvin's article on elasticity in the Ninth Edition of the Encyclopedia Britannica (1878). R. ROCCA, Junior Member, and M. B. BEVER, Member AIME, are Research Assistant in Metallurgy and Associate Professor of Metallurgy, respectiuely, Massachusetts Institute of Technology, Cambridge, Mass. AIME New York Meeting, Feb. 1950. TP 2760 E. Discussion (2 copies) may be sent to Transactions AIME before APT. 1, 1950, and is scheduled for publication Nov. 1950. Manuscript received Oct. 15, 1949.

Jan 1, 1951

THIS chapter and Chapter 19 deal with the heat quantities involved in open-hearth steelmaking, including the thermal efficiency of the furnace as a generator of high-temperature heat, the heat storage in the steel and slag produced and in the furnace walls, and the heats of the various chemical reactions involved in combustion, in the formation of slag, and the refining of steel. The fundamental laws to be considered are the first two laws of thermodynamics as applied to problems involving sensible and potential (or latent) heat only: 1. Heat input equals heat outflow plus storage. 2. Heat may be transferred only from a hotter body to a colder one. The first of these laws relates to the various heat quantities or the heat balance of the process. No one has as yet made an open-hearth heat balance that came out almost exactly balanced. The cause probably lies in the difficulties of accurate temperature and flow-rate measurements at the high temperatures involved and the inherent complexities in flow distribution and air leakage present in any real open-hearth furnace system. Some idea of the magnitude of the heat quantities involved can be obtained by a brief, crude outline of the heat balance of a 90-ton heat of steel. We will assume a 60 to 70 per cent hot- metal charge in a fairly fast working and only moderately efficient furnace, burning fuel oil, with a fuel consumption of around 4 million Btu per net ton of ingots produced. The time from start of charge to tap is 9 hr. During this period, the oil burned represents 360 million Btu and the sensible heat in the preheated air at the port ends is 117 million Btu, so that the total heat input at the ports is 477 million Btu. Heat stored in the steel and slag at the end of the heat, plus the various amounts absorbed by certain bath reactions, amounts to a total of 195 million Btu, but 120 million of this is supplied by the heat in the hot metal and by various heat-evolving reactions in the bath,

Jan 1, 1951

By Wallace W. Roepke

The Bureau of Mines determined coal-cutting forces and primary dust generation of four styles of radial gage bits as used on end rings of continuous mining machines. Direct comparisons for reference were made with two widely used conical plumb-bob types having 60' and 90' (nominal) included tip angles. The cutting forces for all of the gage bits were similar to those of the 60°-tip plumb-bob bit. All bits except the RAD-3 gage bit generated similar amounts of primary total dust at shallow cutting, but during deeper cutting, the amounts varied and the gage bits produced as much as 2-1/2 times the dust produced by the 60° bit. This seems atypical since past experience has always shown differences in dust generation at shallow cutting. The specific energy was more like that found previously with other bits, since the values were spread at shallow cutting but became nearly similar at deeper cuts. The 90° bit and the RAD-3 gage bit are not recommended for use except in extremely difficult cutting conditions where dust and forces are of secondary importance. The choice among the remaining four bits can be made on the basis of dust, energy, forces, or cost, as circumstances dictate.

Jan 1, 1983

By Donald Towse

Geothermal heat might become an important fuel for several reasons: (1) To substitute for other scarce and critical fuels. (2) Because it may be less costly to the user than alternate fuels. (3) Because its production may be more profitable than production of other fuels. (4) Or for a number of other more or less non-economic reasons such as convenience or because of less environmental impact. In competition with conventional and other non-conventional fuels, geothermal heat must score well on one or more of those points. This study first considers projections of energy needs in several United States economic sectors and the technical possibility of geothermal heat substituting for other fuels in those sectors. Then, reported and projected costs of energy from geothermal heat are compared with costs of other fuels to show the relative costs of fuels in several economic sectors. Relative costs are reported from a sample of real and hypothetical geothermal projects. The actual cost of energy will vary with each application and the particular circumstances of each geographic location.

Jan 1, 1975

By Alan E. Cameron

WE assemble again today in this comfortable, hospitable Inn to begin this, the 58th, Meeting of our Society. It is just a year ago when last we met but that year was, probably, the most portentious year in the whole history of mankind. In that year, the German 'Atlantic Wall' was broached, the Rhine was crossed, and Germany, as a Nation, has ceased to be. The agony of Europe is over; convalescence may be, probably will be, slow. But blood no longer flows in Europe. Time will heal the sores, cover the scars, regenerate the industries, rebuild the cities, and re-establish the people. True, the war of all wars is not yet over. True, a bloody conflict remains . But, the power of the United Nations now converges on one target. The rain of blood will be heavy. We can hope the storm will be short. The sun is on the horizon. The light of peace 1s in the sky. What of that Peace? Are we ready for it? Have we a 'sure foundation ' for our future world? Are the footings under that foundation broad and substantial? Can we look forward with confidence to a lasting peace and a fruitful life? The United Nations, even as this is being written, are in conference in San Francisco, placing the footings, rearing the foundations for a world edifice. There are bickerings; there are jealousies. The world is tired, and a tired family always squabbles. We can, we must, believe that the decisions they make, the edifices they rear, will be better than anything we each could effect separately. It will be a compromise, probably; it will carry things that will hurt us, just as it will carry things that will hurt others. We can, we must, believe that the good of the whole is a greater good than the good of the part. Each Nation within the United Nations must sacrifice something, each part of each Nation must sacrifice something, each individual within each part of each nation must contribute something, if the whole is to be wholesome. Sacrifice and contribution must be the order of the day if the New World we are about to build is to be worth while. What of Nova Scotia? The world has travelled far in the last year; how far has Nova Scotia gone? Canada has preparations for the Peace under way; what has Nova Scotia done? Is Nova Scotia preparing counter measures for the sacrifices it must make? Is each of us ready to contribute his share?

Jan 1, 1945

By C. A. Pickles

Microwaves are being applied industrially in a number of fields and possess a number of potential advantages that could be applied in extractive metallurgy. Microwave heating has a number of unique characteristics, which distinguish it from the conventional heating methods. In microwave heating, the absorption of energy occurs at the molecular or atomic level and therefore the heat is generated within the material itself. In conventional heating, the exterior temperature is usually higher than the interior, but with microwave heating, the temperature gradient is inverted and thus the interior temperature can be much higher than that of the surface. The energy densities in microwave systems can be relatively high and this in combination with the low thermal conductivities of oxide ores, can lead to very high internal heating rates. In this research, the application of microwave energy for the reduction of a nickeliferous silicate laterite ore has been investigated. The real and imaginary permittivities are the two fundamental properties which determine the microwave absorption characteristics of a material and these were measured for the ore, both with and without carbon additions using the cavity perturbation technique. The microwave heating and reduction experiments were performed in a 0 to 2 kW CTC microwave system. The effects of power input, processing time, sample mass and charcoal additions on the microwave absorption were investigated. Then reduction experiments were performed and the nickel grade of the magnetic concentrate and the nickel recovery in the concentrate were determined.

Jan 1, 2005

By Joe B. Alford

Jan 1, 1971

By Thomas C. Atchison

The purpose of this Bureau of Mines investigation was to measure the amplitude and shape of the strain pulse and the size of the crushed zone produced in a granite by different explosives and to determine how these quantities are related to the detonation properties of the explosives. The reflection theory of rock breakage has shown that the amplitude and shape of the strain pulse incident at a free surface determine the fragmentation and volume of rock broken. Determination of the properties of an explosive that control the characteristics of the strain pulse produced in the rock will help in evaluating explosives for use in blasting. The investigation showed the different explosives produced a twofold variation in the amplitude of the strain pulse but little variation in the shape of the pulse. The explosives also produced a twofold variation in the volume of the crushed zone, but differences among the explosives were more accurately determined by strain-amplitude measurements than by crushed-zone measurements. The peak amplitude of the strain pulse and the volume of the crushed zone correlated with the calculated detonation pressure of the explosive.

Jan 1, 1959

By Neussias Inocêncio Henrique

O processo de coqueificação em uma Coqueria do tipo Heat Recovery é baseado na queima da matéria volátil presente no carvão, principal combustível para aquecimento dos fornos. A Combustão dos gases tem que ocorre dentro da câmara primaria (interior do forno) e na câmara secundaria (Sole Flue). Devido a algumas interferências no processo de coqueificação não ocorre a queima completa dos gases no forno e com isso a combustão terciária ocorre nos coletores de gases (equipamento destinado apenas para transporte dos gases de combustão). Com a queima dos gases nos coletores temos o aumento de temperatura no interior do duto e como a estrutura refratária não foi projetada para suportar esse limite máximo de temperatura acontece a contração e posteriormente colapso do refratário causando perdas em todo o processo. Os principais benefícios após a aplicação dessa técnica é a redução no tempo de reparo, aumento do rendimento de aplicação da massa refratária e prolongamento na vida útil desse equipamento.

Aug 17, 2017

By Lok W. Home

INTRODUCTION Today, raise drilling (boring) has become the stan¬dard method of raising throughout the Western world. It is estimated that the majority of raise footage com¬pleted in 1977 was accomplished by the raise drilling method. Extensive replacement of the drill and shoot system by mechanized raise drilling has occurred be¬cause users have recognized one or more of the follow¬ing advantages. In a direct cost per meter comparison, mechanized raise drilling is economically more attractive than drilling and shooting. Mechanized raise drilling offers improved personnel safety over the drilling and shooting method. Mechanized raise drilling is a faster and more predictable method for excavation than is drilling and shooting. The raise cost per unit of length becomes less as the raise length increases, offering greater flexibility in the overall design of mines. Mechanized raise drilling provides a substantial reduction in labor requirements. 6) Mechanized raise drilling improves the working environment. 7) Mechanized raise drilling improves the rock in¬tegrity of round, unblasted raises. Increasing acceptance of the raise drilling technique is enhanced by continuing equipment development. Today, a wide range of machines and capabilities is available, machine drive systems have been improved, reliability has been increased, and cutter technology is being improved quite rapidly. Table 1 lists the four major manufacturers of raise drilling machines, cutters, and reamers, together with the approximate number of machines that each company had in operation at the end of 1977. Although Reed and Smith are major suppliers of reamers and cutters, they do not manufacture the drilling machines. Four or five other relatively minor suppliers have built machines, reamers, and cutters for raise drilling, but they did not have a substantial num¬ber of machines in the field at the end of 1977. MACHINES FOR MECHANIZED RAISE DRILLING There are three principal arrangements for making machine-bored raises. They include the use of standard raise drills, reversible raise drills, and blind-hole or box¬hole raise drills. Standard Raise Drills The standard raise drilling machine is set up on one mine level or on the surface, and a pilot hole is drilled from that level or surface to a level below. When the pilot hole has been drilled, the raise then is reamed back from the lower level to the upper level or the surface. This arrangement is illustrated in Fig. 1. Reversible Raise Drills The reversible raise drilling machine is set up on a lower level of the mine, and a pilot hole is drilled up¬ward to a higher level. The raise then is reamed back from the upper level to the lower level. This arrange¬ment is illustrated in Fig. 2. The machines used for this type of raise drilling normally are capable of being used as standard raise drills. Blind-Hole or Boxhole Raise Drills The blind-hole or boxhole raise drilling machine is set up on a lower level of the mine, and a full diameter raise is bored to a higher level without the use of a pilot hole. This type of machine is illustrated in Fig. 3. Drill Recommendations If access to upper and lower mine levels is equal, the standard raise drill should be used. The complexity of the equipment and associated handling procedures for boxhole drilling far outweigh any mechanical advantage or reduction in the number of operations, provided that access to an upper level is available. If there is good access to a lower level but only limited access to an upper level, the use of a reversible raise drill should be considered. If there is no access to an upper level, a blind-hole or boxhole raise drill is the only practical mechanized system. MACHINE SELECTION There are six major considerations in selecting a machine for raise drilling. These include operating range, cutter loading, machine structure and main¬tenance, drill string configuration, drive system, and automated controls. Operating Range As shown in Table 2 and Figs. 4 through 6, raise drilling machines are available for a wide range of hole sizes. Standard raise drill ratings range from raises of 0.9 m (3 ft) diam and 120 m (400 ft) length up to raises of 3.5 m (12 ft) diam and 900 m (3000 ft) length. Boxhole raise drilling machines are available for raises ranging from 0.9 m (3 ft) to 2 m (6 ft) diam with lengths up to 90 m (300 ft). Table 2 lists, among other criteria, the torque and thrust of typical machines; torque and thrust are the main criteria for analyzing the capacity of a machine. The raise sizes shown in Table 2 assume a condition of medium hard to hard rock formations and optimum cutter loading. The recommended raise size for a given machine can be exceeded when raising softer rock formations or when the operator is willing to accept a lower level of performance; the performance is related directly to the 1093

Jan 1, 1982

By John A. Wells, Leticia Conca, Kenneth G. Thomas

"Since about 2002 there has been significant capital cost escalation, not inflation, in the mining industry causing turmoil for successful project completion. Project capital costs have more than doubled and some cases tripled in this time period. This has rendered many projects to be economically challenged and in some cases not viable. In addition higher than expected operating costs have further adversely affected project metrics such as NPV and IRR. Capital cost increases for projects have been widely reported globally. This current paper reviews three items. Firstly, why such capital increases and the various components that make up capital estimates. Secondly, it looks at reasons why preliminary estimates, for example at scoping and pre-feasibility level, have been lower than the ultimate constructed costs. Such increases and differences in estimates have caused major problems for mine builders and have led to a general nervousness on the part of those providing project finance. Thirdly, what discipline is needed in project execution in an attempt to mitigate such capital increases. The paper will hopefully give a better understanding of the various issues and factors involved for those in the mining industry.INTRODUCTION The years 2012 and 2013 were a turbulent time for the mining industry. The European economic crisis, politics, metal price volatility and a wave of changes of CEO´s in some of the major mining companies all contributed to a challenging couple of years. Two issues stood out. First, the huge increases reported in the capital costs of projects, where increases of 100% - 300% were not uncommon and in some cases exceeded that during the first decade of the 21st century. Second, company write downs related to takeovers during the boom and the stabilization/correction in commodity prices. These have led to great uncertainty, made it difficult (or impossible) to raise project financing costs, contributed to the changes at CEO level and placed many projects either on hold or cancelled altogether. It is commonplace now to read of companies talking of reduced capital expenditure and making a complete review of their projects and operations to contain costs."

Jan 1, 2014

By Vernon C. Allison

The explosibility of coal dust has long been recognized by competent investigators as constituting one of the dangers of mining coal and in the use of pulverized coal as a fuel in industrial plants. The Bureau of Mines has carried on extensive series of experiments dealing with this subject, and has not only developed methods for the practical prevention of this danger, but in the, course of these experiments has developed a standard method of determining the relative explosibility of coal dusts and other organic dusts.3 Oil shale contains compounds 'of carbon and hydrogen that are either of a petroleum nature and are strongly ,adsorbed upon the incombustible part of the shale, or else are present in the shale as a compound ("kerogen") which has the property of changing into petroleum-like products when acted upon by heat. The oil shales may contain varying amounts of the organic matter, ranging from a trace to more than 66 per cent, depending upon their richness; therefore, it is important to know whether the dusts formed in mining and handling these oil shales are explosive when mixed with air and if so, to indicate remedial measures. This paper gives the results of explosibility tests of several pulverized oil shale's, selected as being typical of those which in the future may be used in commercial shale-oil production test on a sample of typical Colorado oil shale has been., published in an earlier paper.4

Jan 1, 1926

By Noel Dent

Increasing interest is being expressed in the development and availability of Electronic Delay Detonators throughout the world. Particularly in open-cast mining, the benefits associated with precise, reliable initiation systems are perceived to be considerable. Many of the systems currently being developed have sophisticated programming requirements associated with them, or are numbered systems that require predetermined layouts to determine timing patterns, and importantly are far more expensive than existing initiation systems.

Jan 1, 1994

By Pedro Lobarinhas

In the present work a two dimensional computational model is derived for the description of the time dependent heap leaching process. The flow inside the heap is calculated using the diffusion equations for the flow in porous media. The soil conductivity is also estimated assuming a close packed structure for the grain packing inside the heap. These equations, with appropriate boundary conditions, are solved using a time step splitting scheme. From this calculation the amount of leaching reagent in contact with the ore at any position inside the heap can be calculated and, once coupled with appropriate reaction equations, the amount of metals extracted can be computed and leaching agent concentration updated. The model is tested with available experimental data and the results have shown to be in a very good agreement. The model predicts all the transient features of the data.

Jan 1, 1999

By L. Yuan, J. Soles, D. Bahrami, W. Tang, R. Thomas

Mine equipment fires remain as one of the most concerning safety issues in the mining industry, and most equipment fires were caused by hot surface ignitions. Detailed experimental investigations were conducted at the NIOSH Pittsburgh Mining Research Division on hot surface ignition of liquid fuels under ventilation in a mining environment. Three types of metal surface materials (stainless steel, cast iron, carbon steel), three types of liquids (diesel fuel, hydraulic fluid, engine oil), four air ventilation speeds (0, 0.5, 1.5, 3 m/s) were used to study the hot surface ignition probability under these conditions. Visual observation and thermocouples attached on the metal surface were used to indicate the hot surface ignition from the measured temperatures. Results show that the type of metal has a noticeable effect on the hot surface ignition, while ventilation speed has a mixed influence on ignition. Different types of liquid fuels also show different ranges of ignition temperature. Results from this work can be used to help understand equipment mine fires and develop mitigation strategies.

Mar 2, 2022

By S. Banisi, M. R. Yarahmadi, S. R. Mortazavi

Nowadays the development of automatic on-line sampling systems has enabled large amounts of data to be available to plant managers. These data are inevitably prone to random and sometimes systematic errors. Data reconciliation methods are used to deal with random errors. In these methods, the measured data are adjusted in accordance to their error, so that the mass conservation law is satisfied at the same time. Measured data may also contain systematic errors, using these data in mass balancing software will result in inaccurate or even irrational results. In this paper three methods for detecting systematic errors (global test, node constraint test and maximum power constraint test) were presented. A step by step method to locate the systematic errors was demonstrated. Then, the new version of Movazen©, a mass balancing software, was introduced and used to locate systematic errors in the measurements taken from the Sarcheshmeh pilot plant copper flotation circuit. Keywords: Mass balancing, data reconciliation, random error, systematic error

Jan 1, 2020

By W. J. Verner, J. R. Lucas

Billions of tons of bulk solid materials are processed through our industrial plants each year, and the tonnage is steadily rising. It has been estimated that for every dollar spent in industry as a whole, approxinlately 30 cents is consumed in the handling of bulk solid materials. It is in this category that tremendous savings are possible through the use of improved techniques. Since World War 11, the mining, steel, chemical, and grain industries, among others have made use of increased materials-handling automation in order to gain some of these savings. However, in a chain of automatic operations, every link must be completely reliable, for if there is a single failure, the whole system immediately becomes ineffective. Only too often the weak link in the chain proves to be the flow of bulk solids from bins. To contribute to the fundamental knowledge in this area, a research study has been continuing at The Ohio State University. The principal objective of the investigation has been to study the internal stresses existing in confined bulk solids. LITERATURE SURVEY Literature studies have revealed that many outstanding people have made contributions to the field of bulk solids. For instance, C. F. Jenkin,1 suggested: a. The pressure on a bin wall is not directly proportional to the depth beneath the surface of material in the bin. b. The vertical pressure distribution on the base of a bin is not actually uniform but is a variable. c. Arches form in bins as a result of very small deformations of the material in the bin. This deformation causes a series of gaps to appear, and consequently causes the disappearance of diagonal forces that cannot act across these gaps. The removal of the diagonal forces causes horizontal forces to be introduced which seem to be the chief cause of arching. 11. A. Janssen,4 in 1895 in connection with his experiments on bins, derived a differential equation to describe both the lateral and vertical pressure in bins with vertical sides. This represents a significant contribution to bulk solid theory, and thus its solution is reproduced as follows: L = KV = RW/U' [l-e -U'KY/R] I where L is the lateral pressure of the bulk solid in psf., V is the vertical pressure of the bulk solid in psf., K is the ratio of the lateral pressure to the vertical pressure at any point, R is the hydraulic radius of the bin in feet, W is the density of the bulk solid in lbs. per cubic feet, U' is the coefficient of friction between the stored material and the bin wall, and Y is the head of material above the point in question in feet. In 1903, Jamieson,6 in an elaborate series of experiments on full sized bins measured vertical and lateral pressures by hydraulic diaphragms. He determined many values for mediums of corn, wheat, peas, and flaxseed. In 1951, Caughey, Tooles, and scheer3 measured both lateral and vertical pressure in deep bins by using strain guages on steel bands. Values were calculated for cement, gravel, sand, soy beans, shelled corn

Jan 1, 1961

By C. Heiss, A. Hofmann

Due to an explosion in an Austrian steel works during the basic oxygen process, the Chair of Mining Engineering and Mineral Economics at the Montanuniversitaet Leoben was assigned with the set-up of a test arrangement to study the effects of large-scale particle emissions on the plant´s installations and the testing of various structures and structure-combinations to be applied as explosive-proof enclosure.

Jan 1, 2012

By Graham Davey

"Low speed stirred milling has been employed for many years in the metalliferous and industrial minerals industries. High speed stirred milling is a relatively new method of grinding in the metalliferous process industries. However it has been it has been in wide spread use in the industrial mineral field for over 30 years for various minerals. Many existing metallurgical operations are looking to maximize economic return from existing deposits, requiring new thinking and technologies. By combining low speed and high-speed milling fine and ultrafine grinding efficiency and operating costs can be improved.The correct selection of different fine grinding technologies is covered, when each mill is applicable and when a combination of the VERTIMILL® Grinding Mill and SMD provides the best economic solution.INTRODUCTIONUltra-fine grinding of minerals has been in wide spread use in the industrial mineral field for over 30 years. Within the last 10 years the metalliferous industry has shown interest in the ability to produce ultrafine particles, as chemical, physio-chemical and physical separation processes have advanced to be able to treat ultrafine metalliferous particles. Also as the primary mineral deposits, around the world are depleted, new more difficult deposits must be mined. Existing operations are also looking to maximize economic return from existing deposits, requiring new thinking and technologies.The traditional approach for gold containing refractory material has been to liberate the locked gold by chemically destroying the pyrite through oxidation. Roasting, pressure oxidation, and bacterial oxidation all employ various degrees of temperature, pressure and catalysis to react the pyrite with oxygen to produce iron oxide and sulfur by-products. However all of these methods are economically impacted due to specific operational added requirements and emissions controls. Pressure and bacterial oxidation have very high capital and operating costs."

Jan 1, 2006