Search Documents

Although Canadian bentonite is competitive in quality for most uses, it has not been accepted for the pelletizing of iron ore concentrates. In 1962, Canada consumed about 10,000 tons of imported bentonite for this use. By the end of 1965, the planned domestic consumption for this purpose alone will probably be more than 100,000 tons a year, valued at about $3 million. Consequently, a challenge exists for the establishment of a Canadian source of high-quality bentonite for pelletizing. Such a bentonite would also be suitable for the two other major applications -well drilling and foundry use. Brief mention is made of such topics as the identification, 1noperties, occurrences, exploration, applications, technology and laboratory testing of this clay. In particular, the type of bentonite in demand, the geological horizons warranting exploration, and simple preliminary test methods are discussed.

Jan 1, 1964

Since 1955 Gaspe Mines has produced 144 million tonnes of ore, averaging 0.87% Cu, mined from two open pits and underground workings. In 1994, four exploration drill holes discovered a buried porphyry/skarn Cu-Mo deposit at depths of between 1000 m and 1700 m below the top of Porphyry Mountain. The mineralization and alteration associated with the Porphyry mountain quartz monzonite does not outcrop. A total of 19,500 m of drilling in 12 drill holes has outlined 200 million tonnes grading 0.73% Cu and 0.08% Mo. Mineralization occurs as veins and disseminations of chalcopyrite and molybdenite. Drilling and feasibility studies continue.

Jan 1, 1998

By Jun Lu

The Pittsburgh seam is the most extensively mined coal bed in the Appalachian Basin. Unlike most other prominent coal seams, the Pittsburgh seam typically includes a sequence of immediate roof coals and intervening rock binders (or ?draw slate?), most of which are within mineable horizons. Furthermore, unlike the main bench, the thickness of the overlying roof coals and their intervening rock binders can vary significantly. For instance, in southwestern Pennsylvania, the Pittsburgh seam main bench typically ranges from about 5.0 to 6.0 feet thick with minimal variation over short distances. On the other hand, the Pittsburgh seam roof coals and immediate roof binder typically range from a few inches to several feet, and in certain geologic settings can vary significantly over short distances. Additionally, in some locations, very thick draw slate can totally replace the roof coals. Since the draw slate, which typically consists of claystone or clayladen shale, is relatively weak, the presence of thick and variable draw slate in the roof and rib can significantly affect mine safety and productivity. This paper presents the adverse effect of thick draw slate on a 1500-foot-wide longwall face in a southwestern Pennsylvania coal mine. Mapping of the thick draw slate, numerical models which illustrate stress distribution and failure associated with thick draw slate, and operational adjustments instituted to mitigate the negative impact of thick draw slate will be discussed in detail.

Jan 1, 2013

By D Johns, L Murray

This paper discusses pore pressures in the embankments of tailings dams by comparing real world data with common design assumptions. Assessment of pore pressures has implications on material behaviour interpretation from CPT investigations and, therefore, on the design. For example, the assumption of hydrostatic pressure is conservative for limit equilibrium stability analyses but may be un-conservative in assessing the potential for contractive behaviour and strength loss during shearing. This paper presents some real world data, the investigation methods to determine the pore pressures, and subsequent interpretation of CPT data and material parameters such as the state parameter. It also examines the design implications of assuming a hydrostatic pressure distribution, by comparing results from that assumption with those obtained using the real pore pressures.CITATION:Johns, D and Murray, L, 2018. Characterisation of pore pressure in tailings dams and the implications for design, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 239–249 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By H. Gallardo, J. Yianatos

Flotation is a separation process in which mineral recovery depends on the particle surface properties. The selective collection of particles by air bubbles requires hydrophobic mineral surfaces. Hydrophobicity can be selectively induced on a valuable mineral surface by means of reagents. For this purpose, it is required that mineral grains in the ore become physically liberated or exposed in the particle surface after grinding. The grinding process generates three types of particles according their exposed surface in the floatable mineral: locked particles (0-10%), associated particles (10-90%) and liberated particles (90-100%). Locked particles have low floatability, and they typically show low recovery (<20%), while liberated particles have a high floatability and can be easily recovered (98-100%) at different particle sizes (10-150 µm). The main challenge in the flotation process is the recovery of associated particles. These particles typically have recoveries of 20-80%, but strongly depend on the particle size, particle surface liberation and collector dosage. Recent studies on particle floatability by size-liberation have significantly contributed to improving the characterization of flotation processes. In this work, a study of flotation recovery of associated particles of 10-90% liberation is presented for particle sizes (10-150 µm) and collector dosages (5-40 g/ton). In this work historical data on galena recovery based on particle cross-section composition of galena was used, assuming they represent an acceptable estimate of particle surface composition, as shown by some previous researchers. The results showed that galena recovery can be well represented by a model consisting of the interaction of a linear function and a Gamma distribution function to account for the liberation and the particle size effects. Consequently, an alternative approach for modelling the recovery of associated mineral (10-90% liberation), with a reduced number of parameters, was developed and validated.

Jan 1, 2018

By Yutaka Shiraishi

Two methods were developed to measure the viscosity of the slag from the glassy to the liquid states in an ascending temperature process. The first method employs rotating parallel plates within which is placed a solid cylindrical sample in line with a sphere. The second method uses a tube which is pushed into a sample held in a rotating crucible. Both methods were tested using standard glasses, including boron trioxide and NBS standard glass #711. The main difference between these two methods is in sample preparation. Comparative measurements between two methods were performed using a sodium boro-disilicate glass containing 5%mol of alumina. The results showed good agreement in the mid-range of glassy viscosities, 105 to 107 Pa.s. In the liquid state, there were no significant differences between the two methods.

Jan 1, 2003

By J. Iannicelli

An entirely new level of magnetic filtration technology was put into full commercial production by the kaolin industry of Georgia, U.S.A. during 1973-1974. At present, four kaolin producers in Georgia are operating large magnetic filters each capable of processing over 1000 gallons of kaolin slurry per minute or over 65 tons of kaolin per hour on a dry basis. A fifth large filter will go on stream in August, 1975. Four of these units are 84" machines manufactured by the Pacific Electric Motor Company of Oakland, California. When operated at the maximum 1000 g, p. m. rate, these five large magnetic filters have a combined capacity approximating the entire waterwashed coating and filler kaolin produced in the U.S.

Jan 1, 1976

By P. G. Corser

A gold and silver open-pit mine located in northwestern Chile contracted ACZ in 1991-92 to assess the stability of their spent ore pile and to determine the cause and magnitude of cyanide contamination associated with leaching operations. The mine is a conventional open-pit located at an elevation of approximately 4,800 meters (m.) (15,744 feet). A spent ore pile is located approximately 2,000 m. southwest of the mine and approximately 1,000 m. northeast of the active pad and plant facilities. The pile was constructed on a gentle northwest slope dipping 12 to 13 degrees. The pile is bordered by a small river to the northwest and by a larger river to the northeast. Both rivers eventually flow into Bolivia. Heap leaching and processing commenced at the mine in 1988. Since 1988, nearly 6.0 million tons of ore at an average grade of 1.96 grams/ton (0.07 ounces/ton) of gold and 52 grams/ton (1.83 ounces/ton) of silver have been treated by cyanide heap leach methods with zinc (Merrill Crowe) precipitation. In approximately three years of operation, the mine has yielded more than 225,000 ounces of gold and over 1.5 million ounces of silver. Currently ore is agglomerated and hauled to the leach pad by truck and is top loaded to produce a 5-meter lift height. Four contiguous reusable (on/off) leaching pads were constructed with an asphalt layer above a carefully compacted sub-base of High Density Polyethylene (HDPE) liner and screened fines. Leach solution of pH 10-11 containing 1.2 to 1.5 gram/liter of cyanide is applied to the heap at a rate of 10 liter/hour/square meter for a total active application period of 30 days. Leached (spent) ore is transferred to the spent ore pile located approximately 1,000 meters to the northeast. The pile currently contains approximately 6 million tons of spent ore. The pile liner, which has been constructed over a prepared sub-grade consists of three geosynthetic layers (geotextile/flexible membrane liner/geotextile). Long term objectives include washing the pile to recover an additional 3 to 4 percent gold and silver.

Jan 1, 1993

By A. M. Amdur, A. N. Matushkina, G. I. Gazaleeva

"The article highlights results of theoretical and practical studies on the enlargement of fine gold in the process of heat treatment. The object of research is refractory gold silicate-carbonate ores of Vorontsovskoe Deposit (Northern Ural), containing fine gold. For setting up experiments and analyzing the results were used the methods of applied mathematics, mathematical statistics, mathematical and physical modeling. Modeling and calculations were performed using the software package HSC Chemistry 6.0, MatLab, setting up a full factorial experiment and other modern modeling methods. Using a scanning electron microscope, the distribution of fine-dispersed ore gold particles by size was studied. It was found that gold particles smaller than 0,4 µm smoothed the vertices and edges, i.e. they are of globules with an amorphous structure. Amorphous materials are nonequilibrium phases with high thermodynamic activity. The physicochemical properties such as melting temperature, diffusion coefficients, the content of metal impurities differ from the properties of the solid phases. In the course of the research were formulated the following scientific bases of the mechanism of enlargement of the gold particles: - the movement of dispersed droplets of gold in the process of external heat to the surface of the ore particles in the pore occurs under the action of thermocapillary pressure; - after melting of the host rock occurs flotation of molten droplets by the bubbles of gases and coagulation of fine gold; - the conditions of flotation drops of gold in oxide melts; floated drops of radius R = 1-100 µm. Analysis of the equilibrium at the perimeter of wetting a drop of gold-oxide melt-gas showed that the scheme of the tension will not significantly differ from the case of solid gold, while the radius of the gas bubbles should be at least 2 times greater than the radius of drops of gold. The proposed method of predicting the results of the enrichment of the proposed scheme, including heat treatment and gravitational centrifugal concentration of crushed ore. Experimental verification of the proposed scheme in the laboratory showed a satisfactory convergence of experiment and prediction. Gold recovery in the concentrate was 33,84 against 33,7 percent forecast. The increase in overall gold recovery to a gravity concentrate after heat treatment is more than 20 %."

Jan 1, 2018

By J. J. Rush

Neutron scattering and analysis techniques are extremely powerful, often unique, probes for the characterization of the amount, location, bonding states, and dynamics of hydrogen in all classes of materials. Developments over the past decade at the NIST Center for Neutron Research and elsewhere have greatly increased the sensitivity and dynamic range of neutron methods. In this paper, we provide a flavor of the capabilities of modem neutron instrumentation for the study of hydrogen in a number of technologically interesting systems, including metal hydrides, fuel-cell materials, fullerenes, and disordered carbons.

Jan 1, 2002

By Karl Christopherson, Vanessa de Viterbo

Trim blasting is an integral part of the mining processes at the Morenci Mine, a Freeport-McMoRan Copper & Gold Inc. property. Trim blasting near high-walls or Finals blasting requires a tighter distribution of energy but a reduction in total energy factor near the wall. Recent Finals blasting in Morenci Mine was allowing the shovel to dig to the final design limit, but causing high-wall instability due to excessive energy or production of energy (blast design and timing). Slope instability events reduced production in two of the three operating pits in Morenci over 2009. In order to avoid high-wall instability from Finals blasting, a new method was required. The new method utilizes air-decks, unconventional row timing, and blast design based on the geology predicted. Many different geologic structures and rock types exist in Morenci, and different strategies were needed for the many predicted geologies. Drill penetration rate and core mapping were the primary tools for determining the blast design. Patterns were designed within a consistent geology; with weaker rock types receiving a lighter load than the stronger rock types. Penetration rate returned by the drill would be the determining factor on the actual rock hardness. Maintaining the pattern geometry on Finals designs should not be an issue as long as the lb/hole is adjusted to reduce powder factor close to the high-wall. One requirement of Finals blasting should be that the powder factor matches the geology as closely as possible. A softer, fractured zone should use approximately one-half to two-thirds the explosive charge of a competent, sound geological zone. This has been incorporated into the final Trim blast design. It is impossible to protect every high-wall from close-in blasting, especially those with crossing prominent joint sets inclined toward wedge failure, but this new design has provided protection on walls where the mine was encountering problems.

Jan 1, 2011

By L. G. Bergh

The experience developing a supervisory control and information systems in a SX pilot plant is presented. The plant is located at the Process Control Laboratory, Santa Maria University, in Chile. In this work, the problem of controlling this process is discussed and related literature is briefly reviewed. Then, an innovative control scheme organized in three levels, local, hydrodynamic, and metallurgical supervisory controls is presented in an architecture including field controllers, PLC, and PC networks. Operating decisions in the metallurgical supervisory control are taken with incomplete information from on-stream analyzers. The control proposed is based on metal and acid concentration predictions of intermediate and exiting streams through the use of dynamic and static models and flow rates and input concentration measurements. Preliminary results are presented. The main objectives are to develop and test intelligent techniques in a hybrid system, and to study measurement and supervisory control problems. It is expected to produce reliable results that will contribute to improve the efficiency of this emerging and important process.

Jan 1, 2007

By Ray Nivens, Umit Turunc, Caroline Sui, Nick Morrison, Douglas Steiner

"In most copper mines and concentrators, mill water is continuously recovered and reused, with fresh water added to make up for losses. When mixed, these water chemistries can lead to severe scaling, especially in pipes, tanks and pumps on the mill water supply side, reducing flows and causing significant production losses.At KGHM Robinson Nevada Mining Company, increases in the fresh water addition ratios resulted in severe scaling problems and premature pump failures thereby jeopardizing plant production. What initially appeared to be a few isolated scaling events eventually unfolded into a recurring pattern of water supply-related production losses with increasing severity. Through completion of detailed root cause analysis, chemistry modeling, laboratory work, in-plant testing and system engineering, the mechanisms of scaling were identified and addressed.Advancements in fresh water addition practices and antiscalant application methods resulted in a stepwise reduction of the mill water scaling. Cost savings and production benefits were significant to the plant’s financial metrics.IntroductionThe production of mineral and metal concentrates using the flotation process requires large quantities of water. Flotation is utilized as the primary means for beneficiation with sulfide ores. Mined ores are crushed and ground into a slurry of 20-55% solids. For each ton of ore, 400-900 gallons of water1 are needed to supply the grinding mill. Additional water is needed in the flotation circuit as well. With many modern mills operating at2 11,000-165,000 tons/day, water supply volumes can be upwards of 3,000 gpm to 100,000 gpm of flow.For plants operating at or above capacity, disruptions and restrictions in water supply flow can have a direct impact on the production and recovery of the metal. Water supply flow can be limited for a wide variety of reasons but of interest are those limitations that are due to mineral scaling. Mineral scaling is the selective point precipitation of inorganic species above saturation concentrations. Precipitated species form flow-restricting deposits in the mill water system (tanks, pumps, pipe and valves), that will eventually impact water supply to the concentrator."

Jan 1, 2017

By Bruce H. Baker

Studies of used or unused refractory materials are excellent examples of applied mineralogy in industry. Refractory materials are mineral substances containing ceramic or chemical bonding systems. Knowledge of the mineral composition, bonding, and textural relationships often explains the resulting physical property values of a refractory and contributes to the interpretation of refractory wear mechanisms occurring in steel plant service.

Jan 1, 1982

By A. Carbonari

In order to gain competitiveness and compete at a global level, construction companies should improve their efficiency. The problem is even more relevant in the construction field, whose work processes find it hard to evolve towards new automated methods and techniques in the management field. For that reason, this paper suggests how construction companies could apply new technologies to implement automated management of environmental hazards. Based on a survey regarding the environmental risks presently experienced in construction sites, noise and dust were considered two of the main hazards. So in this paper a networked system for real time remote monitoring of the spatial distribution of dust in construction sites was developed. Such a system would relieve builders from the commitment of on-site surveys, allowing for a continuous monitoring of the site conditions and of the real exposure of each worker and pass-by to the pollutants generated by construction works. The main system requirements considered are: easy to deploy, reliable, as accurate as needed to be able to send real-time warnings and store a good estimation of the real exposure to which involved people have been subject to. So far the research produced a prototypical hardware for dust monitoring made up of wireless sensors which can be easily deployed on site. The sensors were calibrated by means of laboratory tests, where their measurements were compared with those collected by means of highly accurate instruments, which were taken as a reference. Thanks to these experiments, calibration curves for the sensors were worked out, showing also the measurement range of the sensors.

Aug 1, 2013

By G. V. Sullivan

The Bureau of Mines conducted preliminary beneficiation studies of a gold-bearing graphitic schist from Blue Hill, Tallapoosa County, Ala. The average analysis of the material was 0.08 oz/ton gold. Tabling of minus 35-mesh material recovered 83 to 94 percent of the gold at grades of 6.925 to 2.165 oz/ton, respectively. A combination of jigging and tabling resulted in a concentrate assaying 24.3 oz/ton gold and contained 87 percent of the total gold. Treatment of the material by jigging, tabling, and amalgamation recovered 86.5 percent of the gold.

Jan 1, 1969

By V. A. Masloboev, A. V. Svetlov, D. V. Makarov

"The methods of heap leaching are considered to be the most promising for the low-grade copper-nickel raw materials. The article presents intensification capabilities of the process. Objects of research: the low-grade copper-nickel ores of Moncheplutone deposits (Moroshkovoye Lake, Nyud Terrasa, Nittis-Kumuzh’ya-Travyanaya (NKT), as well as the copper-nickel ore dressing tailings of the “Kola MMC” JSC. The following directions for the intensification of the low-grade copper-nickel raw materials heap leaching have been considered: preliminary electric pulse destruction (EPD) of ore; ore crushing and further sulfuric acid agglomeration. The impact of sulfuric acid concentration (1-3%) on the extraction of non-ferrous metals kinetics from the copper-nickel ore dressing tailings under various conditions of the percolation leaching has been studied. INTRODUCTION The low-grade grade sulfide ores at the abandoned and producing deposits, overburden rocks, mill tailings and non-ferrous slag are thought to be one of the large-scale sources for non-ferrous metals, on the one hand. On the other hand, they are known to be the subjects of emergency environmental danger. For this reason, the use of mine dumps and tailings, as well as the remained ores left in the ground as raw products, and at the same time decreasing the load on environment, are considered to be the pressing ecological and economic issue (Chanturia et al., 2012). Methods of heap hydrometallurgical and bacterial leaching are sure to be potentially productive for processing such low-grade and technogenic raw materials (Petersen, 2016). The early studies of hydrometallurgical method possibility to process copper-nickel ores of the Murmansk region deposits were launched in the seventies of the previous century (Golovko et al., 1978). For referencing purposes, the main types of impregnated ores from the deposits Zhdanovskoye, Kaula, Sopchinsky Plast and Lovnoozerskoye were selected. The metal content varied, as %: 0.46-1.49 of nickel, 0.01-0.62 of copper. In the first experiments, the solution containing 150g/l of H2SO4 and 135g/l of NaCl, was used in the capacity of leaching reagent. The possibility of underground metals leaching from the ores of the Lovnoozerskoye deposit was justified due to the performed laboratory and further large-sized tests."

Jan 1, 2018

By D Laurence, L Ge

This paper demonstrates use of remotely sensed imagery in promoting sustainable mining. Remote sensing technology can be used during all phases of a mining project û from evaluating the resource, to making extraction more cost-effective, through to monitoring, mine closure and remediation. Use of the new generation of satellite platforms with the capability of acquiring satellite data with higher spectral and spatial resolution have the capability to emerge as essential indicator for sustainable development in the minerals industry. A life cycle approach to satellite imagery is discussed. The use of an imagery of the site prior to mining activity establishes the environmental baseline, guides mitigation measures and eventual help in suggesting remediation. Remote imagery provides the cost-effective means of monitoring reclamation, including the growth of planted vegetation, of the mine site and surrounding area. The latest advancements in satellite remote sensing are highlighted to meet the newer challenges of sustainable mining practices. Some of the worldwide successful remote sensing applications for the measurement and evaluation of the sustainable development impact of mining operations are described. Presently available source of imagery and its comparative advantages and disadvantages are provided as a guide. Finally, the limitations of this tool are indicated.

Jan 1, 2009

By B. Morris

This presentation will describe the process by which the Quebrada Blanca (QB) copper project in northern Chile was financed. It will also show how a relatively junior mining company addressed the problems created by its inability to provide its share of the equity funding and the guarantees required by the project lenders. QB is located in the semi-arid Andean highlands of northern Chile, 170 kilometres southeast of the port of Iquique and 30 kilometres west of the border with Bolivia, at an altitude of about 4,300 metres (14,000 feet). Figure 1 depicts the project&apos;s location. The QB orebody is a secondarily enriched porphyry copper deposit containing reserves of 85 million metric tons grading 1.3 percent copper. Underlying the enriched zone is a significant primary ore zone containing several hundred million metric tons grading about 0.5 percent copper. In the late seventies and early eighties Falconbridge and its affiliates spent $20-30 million dollars exploring the deposit and conducting feasibility studies. For a variety of reasons they decided not to develop the property which was returned to its owners, Empresa Nacional de Mineria (ENAMI), which is a Chilean state mining corporation. In 1988 ENAMI announced its intention to privatize the property through a public bidding procedure.

Jan 1, 1993

By D. C. R. Espinosa, P. Aliprandini, J. A. S. Tenório, M. M. Jiménez Correa

"Nickel and cobalt are the main value metals in nickel laterite ore. Cyanex 272 is an extractant used to separate nickel from cobalt present in leach solutions. Previous studies demonstrated the extraction of cobalt, magnesium and manganese at pH 5 using Cyanex 272 as extractant, while nickel remained in aqueous solution. However, it is difficult to separate cobalt from a solution containing magnesium and manganese. One possibility to change the metals’ behavior during the solvent extraction process is to change the mixture of extractants used. In order to study the solvent extraction of cobalt from a solution containing manganese, magnesium and nickel, a mixture of two extractants was investigated. Cyanex 272 (CY) and Versatic 10 (VC) were selected as extractants in the organic phase. The extractant concentrations used were: 20% CY; 15% CY, 5% VC; 10% CY, 10% VC; 5% CY, 15% VC; and 20% VC. In all cases, kerosene was used as a diluent, at 80 vol%. The synthetic leach solution used in this study was prepared according to the composition of a typical nickel laterite leach solution. The pH value of the solution used was 5, and the aqueous/organic ratio used in solvent extraction testwork was 1/1. The study has shown that the composition of the organic extractant mixture did not increase cobalt separation.INTRODUCTION Sulfide and laterite deposits are the main sources of nickel. However, production from nickel sulfide ores has been decreasing over the years, relatively speaking, increasing the focus on the exploitation of laterite nickel ores (McDonald & Whittington, 2008). Laterite ore deposits are found in tropical and subtropical regions. A characteristic of laterite ores is the presence of a complex and heterogeneous mixture of metals (Crundwell, Moats, Ramachandran, Robinson, & Davenport, 2011; Georgiou & Papangelakis, 1998; Gupta, 2003; Kesler & Simon, 2015; Moskalyk & Alfantazi, 2002; Oliveira, 1990). Nickel concentrations in laterite ores are typically 1–2% (Dalvi, Bacon, & Osborne, 2004)."

Jan 1, 2017