Search Documents

By William J. Campbell

This analytical method development and evaluation was undertaken by the Bureau of Mines to provide accurate determinations of eight minor elements in low-alloy steels prepared from ferrous scrap. Fluorescent X-ray spectrography was the principal method investigated. Confirming analyses were made by conventional instrumental and chemical methods. All X-ray data were processed by a timesharing computer. No corrections were found necessary for inter-element effects or overlapping spectral lines. Concentrations were calculated from the least-square fit of a linear calibration equation derived from measurements on three sets of standard steels. These studies show that X-ray spectrographic analysis of lathe-finished surfaces provides accurate determinations of aluminum, copper, chromium, manganese, nickel, phosphorus, silicon, and tin.

Jan 1, 1973

By M. P. Smith, C. Hughes-Narborough, Y. T. Man

"Money and reputations can be lost in bad projects. Causes of bad mineral processing projects include poor contract definition and purchase of equipment without adequate test work. However, the root cause of many of the problems that can lead to bad projects is not any inanimate object, bad weather or catastrophic natural event but the people working on the projects. Because the people are so critical to the success of a mineral processing project, one must have suitably qualified and experienced people (SQEP) in all key positions. Characteristics that define SQEP include people who have successfully executed projects of similar size before; have undertaken projects treating the same minerals and producing the same valuable products and people who are familiar with designing, operating and implementing the required technologies and unit operations.To minimize the likelihood of future bad mineral processing projects, five recommendations are put forward in relation to the people aspect of a project.1. Attempt to retain SQEP during any down turn in the mining economic cycle so thatthe knowledge and experience can be kept within the industry.2. Increase the effort in attracting young people into the industry and retaining them.3. Set up robust training program to give young professionals a firm foundation of what real life projects and operations are like.4. Provide mentoring and continuous training for people after they have completed their formal graduate training program. Their career progression should be appropriately monitored and controlled.5. People working in projects must be exposed to as many detailed design and other finer issues as possible so that they can comprehend the amount of work required to deliver a project successfully."

Aug 1, 2016

By J. Tuominen

Outokumpu Direct-to-Blister Flash Smelting is currently in operation in two smelters, a third one is under construction and a fourth one is in the design phase. The two smelters in operation are the Glogow 2 smelter of KGHM Polska Miedz S.A. in Poland and the Olympic Dam smelter of BHP Billiton in Australia. The Outokumpu Direct-to-Blister smelter of Konkola Copper Mines Plc. in Zambia is under construction and the new smelter of Glogow 1 is under design and waiting for final go-ahead decision. Additionally, the Garfield smelter of Kennecott Utah Copper Corp. makes blister copper out of matte in a Flash Converting furnace. A similar operation is under construction for Y anggu Xiangguang Copper Co. in China. The slag cleaning process, which is needed to clean the slag of the Direct-to-Blister Flash Smelting Furnace, has different requirements depending on the feed to the flash furnace. These differences are discussed in the paper. The differences between the processes and slag produced are discussed as well as the metallurgical requirements for slag cleaning. The Direct-to-Blister process, where the blister copper is produced directly from concentrate in one step, requires at least a partial treatment of the slag in an electric slag cleaning furnace. The existing impurities determine the specific requirements of the actual cleaning process. The different processes are discussed in the paper. The newest developments of Outokumpu Technology Oy for electric slag cleaning furnace design are presented as well as the characteristics which the furnace shape gives to the process.

Jan 1, 2007

By F. Bosché

Previous research has shown that ?Scan-vs-BIM? systems are powerful to provide valuable information for tracking structural works (progress, quality, safety). However, the transferability of this capability to other construction areas such as MEP works has not been assessed so far. Comparatively, the construction of MEP systems, in particular pipes and ducts, tends to be more flexible with respect to the positioning of individual components, so that Scan-vs-BIM systems could be defeated when tracking MEP installation works. This paper presents recent results on the feasibility and performance of using a Scan-vs- BIM system to track MEP works. The approach followed is presented and then tested with two real-life challenging case studies were conducted simultaneously but totally independently in Canada and Italy. The results show that, as expected, pipes and ducts tend to be more loosely positioned than structural elements leading to a poorer performance of the Scan-vs-BIM system. Nonetheless, it appears that the system works well to assess the level of conformance of site installation works, providing valuable information for estimating emerging performance metrics like ?percent built as-designed?. In addition, the proposed system could also be useful to accelerate and thus reduce the cost of delivering as-built BIM models for in the case of new builds.

Aug 1, 2013

By A. L. Engel

The Bagdad-Chase copper-gold mine south of Ludlow, Calif., was visited by an engineer of the Bureau of Mines in July 1955 to determine the mine's status of activity and to obtain a bulk sample for metallurgical testing. The deposit was discovered in 1903 and has been worked intermittently. It has a production record of about 273,000 tons of ore. The first production of about 150,000 tons was treated in a cyanide plant 2 miles west of Barstow, Calif. The extraction of gold was not satisfactory because of the presence of copper minerals. Since 1910 the ore has been shipped to various smelters in Arizona and California for use as a flux.

Jan 1, 1957

By P. L. Swanson

Over a recent 20-month observation period, the U.S. Bureau of Mines obtained seismogram records from a single vertical-component, short-period seismometer installed at the surface of a metal mine in northern Idaho. The seismic events were analyzed for local (Richter) magnitude (M), time of occurrence, location, and relation to rock bursting and production blasting. Approximately 150 seismic events with -0.5 = M = 2.9 were located within the mine, yielding a b value (slope of the logarithm of the number of events with magnitude greater than M versus M) of 0.5. Event locations were constrained using a dense underground array of high-frequency accelerometers. Twenty of the surface-recorded events, with 0.5 = M = 2.9, were associated with rock bursts that produced damage requiring at least 1/2 day of cleanup and/or repair. Other possibly hazardous rock bursts, with magnitudes as small as -1.1, were numerous but were not associated with significant structural damage. Approximately 60 pct of the seismic events with M > -0.5 and 75 pct of damaging rock bursts occurred within 45 min of blasting. Estimates of characteristic rupture dimensions for rock bursts with -1.1 = M = 2.9, based on a conventional dislocation shear-slip model of failure, range from 3 to 300 m.

Jan 1, 2010

By J. Kretschmann, K. Sakamornsnguan

"Sustainable development is an influential ethical concept in modern mining management. However, the concept is not culturally neutral because it is based on Christian, Western values. These values can be very different from traditional values in emerging mining countries like Thailand, where Buddhist values are dominant. When applying the concept of sustainable development, these differences should be taken into account. Different values imply different interpretations of ‘good mining’. They have a significant impact on how mining operations are evaluated, perceived, operated and managed. This paper attempts to integrate Buddhist principles with approaches of the sustainable development concept. When local values are appreciated and maintained, mining companies and their external stakeholders can identify objectives and approaches that match with their own values and contexts. Practices based on this integrated ethic can help to promote sustainable mining and to minimize communication risks for enterprises in mining countries like Thailand. INTRODUCTION The objective of this paper is to integrate Buddhist principles to the application of sustainable development concept to mining activities. The structure of this paper is divided into four parts. An introduction provides basic information about Thailand, its mining industry and the role of Buddhism on the past development. The second part compares the differences between the sustainable mining framework and the implications of Buddhist principles on mining. In the third part, the core Buddhist teachings are integrated into the sustainable mining framework. This is followed by conclusions in the last part. THAILAND, BUDDHISM, AND MINING Thailand is a constitutional monarchy state in Southeastern Asia with a population size of around 65 million [1]. Its GDP in 2013 was 391 billion USD [2], predominantly deriving from manufacturing (38%), trade, transport and communication (24%), agriculture (8%) and mining and construction (4%). Still the largest part of the Thai workforce (39%) is working in the agricultural sector. The remaining part of the workforce is equally distributed across services, manufacturing, and mining and construction sectors. [3]"

Jan 1, 2015

By W. Jomaa, V. Songmene, O. Mechri, Laval Université, P. Bocher, J. Levesque

"A 2D finite element modelling (FEM), based on pure Lagrangian approach, is developed for studying the serrated chip formation during high speed machining (HSM) of 7075-T651 alloy. The solution was achieved using a commercial software package, ABAQUS/Explicit v6.13. The Johnson-Cooke (JC) constitutive equation is used to describe the work material behaviour. Moreover, the JC damage equation is implemented into the FEM to take into account for the shear localization during the serrated chip formation. Modified Coulomb friction model has been used to characterize the sliding/sticking effects on the tool-chip interface with the friction coefficient and shear flow stress determined by force calibration and machining data, respectively. The proposed FEM is validated using experimental data obtained in HSM of 7075-T651. The FEM was able to predict accurately serrated chip morphology. The intensity of chip segmentation was found to increase with cutting speed.INTRODUCTIONHigh speed machining (HSM) is one of the most used processes for manufacturing aircraft parts with aluminum alloys. For aluminum alloys, the use of HSM increases metal removal rate and reduces the formation of built up edges and burrs. However, it was found that serrated (also named segmented or sawtooth chip) and discontinuous chips can be produced during HSM of some high strength aluminum alloys, such as 7075-T6 alloy (Rao & Shin, 2001). Many parameters were found to affect the segmented/discontinuous chip formation during the machining of aluminum alloys.There are two cases in which the serrated chip can forms: the first is when machining hardened materials (Morehead, Huang, & Luo, 2007), and the second, when machining ductile materials with a cutting speed higher than a critical value (Barry & Byrne, 2002). Different theories and models were developed in order to explain the formation mechanism of such kind of chips. According to Astakhov (2006), the segmented chip formation is attributed to variations in stress and plastic deformation states, and resulting temperatures on the cutting zone. Liyao et al. (2013) stated that the segmented chip formation was mainly attributable to adiabatic shear instability/catastrophic strain localization. Others (Vyas & Shaw, 1999) suggest that the fracture/crack propagation mechanism is at the root of chip generation."

Jan 1, 2016

By G-L. Wu, S-W. Wu

"The hot deformation behaviour of Nb-Ti microalloyed high-strength steel was investigated. Hot compression tests were conducted in the temperature range 900 to 1100°C under strain rates of 0.1, 1, and 5 s-1. Dynamic recrystallization (DRX) occurs as the main flow softening mechanism at high temperature and low strain rate. The hot deformation activation energy was calculated to be about 404 699 J/mol. The constitutive equation was developed to describe the relationship between peak stress, strain rate, and deformation temperature. The characteristics of DRX at different deformation conditions were extracted from the stressstrain curves using the work hardening parameter. The Cingara-McQueen equation was developed to predict the flow curves up to the peak strain. The processing maps were obtained on the basis of a dynamic materials model. The results predict an instability region in the temperature range 1010 to 1100°C when the strain rate exceeds 0.78 s-1. IntroductionThe 700 MPa grade HSLA steel is widely used in engineering machinery, automotive beams, carriages, and axle tubes, etc. (Pan et al., 2017 ). Generally, such grades contain a moderately high amount of Mn (approx. 1.4% and above), and microalloying elements like Nb, Ti, V, and Mo to impart the desired strength and toughness through solid-solution strengthening, precipitation hardening, and grain refinement dislocation strengthening (Chen and Yu, 2012; Opiela, 2014). However, the production costs can be greatly reduced by replacing part of the Nb, V, or Mo with inexpensive Ti and adopting the compact strip production CSP process (Opiela, 2014; Chen et al., 2015). Furthermore, the microalloying technology coupled with new-generation thermomechanical control processing (NG-TMCP) has proved efficient for achieving the proper balance between strength, toughness, ductility, and formability by means of a suitable combination of chemical composition and thermomechanical treatment parameters (Shukla et al., 2012; Wu, Zhou, and Liu, 2017).In hot forming processes, the complex microstructural evolutions are often induced by multiplicative hot deformation mechanisms, such as work hardening (WH), dynamic recovery (DRV), and dynamic recrystallization (DRX) (Zhang et al., 2014; Liang et al., 2015). Dynamic softening behaviour during hot processing has generated considerable interest because component properties are influenced significantly by its corresponding microstructural evolution (Wu et al., 2010). During deformation in the DRX process, deformed grains are replaced with substructures and newly formed fine and uniformly distributed grains. This occurs only when a critical strain for the onset of DRX is reached, and at the same time, the minimum rate of energy dissipating is reached (Ferdowsi et al., 2014). DRV occurs at a high strain rate and low temperature, reducing the stored energy greatly and making DRX difficult (Liang et al., 2015). The microstructural changes during DRX are sensitive to the processing parameters, such as strain rate, deformation temperature, and strain (Zhang et al., 2014; Ferdowsi et al., 2014). Therefore, in order to optimize the hot processing parameters, it is important to understand the behaviour of hot deformation visà- vis control of microstructural evolution."

May 1, 2019

Lignite is a kind of easy-to-slime and low rank coal. It is hard to be separated by the conventional wet coal beneficiation technologies. Meanwhile, in recent decades, a large amount of fine coal (-6 mm) is generated as the mechanized mining technology has been progressively deployed in coal sector, which causes a great difficult for lignite beneficiation and upgrading due to lack of efficient technology available. In this paper, a vibrated gas-fluidized bed was used to separate the -6 mm fine lignite particles. Separation experiments of -6+3 mm and -3+1 mm lignite were carried out in a laboratory-scale vibrated gas-fluidized bed. The effects of several parameters including the superficial air velocity, vibration intensity, bed height and exterior moisture content on the separation performance were experimentally studied. The results show that the optimal separation performance was achieved when the superficial air velocity is 0.3, the vibration intensity is 1.4, the bed height is 50 mm, the exterior moisture content is below 4% (-6+3 mm) and 2% (-3+1 mm). And the probably error E values of -6+3 mm and -3+1 mm size fraction of lignite are 0.202 and 0.225 respectively. The results indicate that a vibrated gas-fluidized bed can provide an effective solution for -6 mm lignite separation.

Feb 23, 2014

By M. Pakala, Z. Fan, Ray Y. Lin

Deposition of hard chromium coatings using electrodeposition is accompanied by emission of hexavalent chromium mists which is a carcinogenic. Hence alternative chromium deposition technologies are being investigated. Sputter deposition is a strong candidate to economically deposit hard chromium coatings in an environmentally friendly way. Chromium coatings of 2-3 µ m thickness were deposited on plain carbon steel coupons using RF magnetron sputter deposition. Depositions were carried out with 0 to 22 vol% nitrogen in the plasma. Structure of the coatings was studied using x-ray diffraction analysis With increasing nitrogen contents, formation of the two nitride phases was observed. The pure chromium phase was detected in coatings with up to 7% nitrogen in the sputtering gas. The solid solution of nitrogen in the pure Cr phase coating was identified by shifts of Cr x-ray diffraction peaks to higher d-spacing. The microhardness of the coatings deposited at a substrate temperature of 200°C showed an increase in hardness with increasing nitrogen content from 600 kgf/mm2 (5.9 GPa) at 0% nitrogen to I250 kgf/mm2 (I2.25 GPa) at 9.5 % nitrogen and a subsequent decrease in hardness to I 100 kgf/mm2 (11 GPa) beyond 9.5 % nitrogen in the sputtering gas. This corresponds to the formation of the hard Cr2N phase, at 9.5 % nitrogen, and CrN phase, at I5.7 % nitrogen. The reported bulk hardness values of Cr2N and CrN are I600 kgf/mm2 (I5.7 GPa) and I 100 kgf/mm2 (11 GPa) respectively. For pure Cr phase coatings, there is a slight increase in hardness for coatings deposited at 7. I % nitrogen from that without nitrogen in the sputtering gas. This could possibly result from the solid solution strengthening of the Cr lattice by nitrogen. For films deposited at 200°C, phases of the deposited films seem to be the overwhelming factor in controlling the microhardness.

Jan 1, 1998

By G. C. S. Burns

"A system has been developed to simulate the mining of the Mufulira orebody. The main output from the system is a picture-gram from which the start date and effective life of all proposed mining faces can be measured. This information provides schedule dates for the completion of major capital development projects and stope preparation activities.The orebody must be divided horizontally into main levels and vertically into blocks of equal interval. Ore reserves are defined by specifying the tonnage contained in each block and main level. Mining faces are defined by their co-ordinates, and may themselves be split into sublevels. The simulation maintains an echelon between contiguous sublevels. Other face parameters control the speed of mining, the availability and relative priority of the face.The required production from each crusher/shaft system is specified. The technique of simulating the mining process in order to achieve the required production is described."

Jan 1, 2014

By J. Finch, F. Rosenblum, McGill University

The self-heating of sulphides can be a major hazard in mining operations and concentrate handling, particularly during transportation and associated storage. Self-heating results from the oxidation of sulphide minerals and can vary from being insignificant to potentially hazardous to life and infrastructure. It is essential that there be a reliable test methodology that can categorize a given sulphide material as to its self-heating potential. By their nature, sulphide ores and concentrates are complex and variable mineral combinations making it difficult to predict their self-heating behavior a-priori based on mineralogy or with a simple "snapshot" test. Furthermore, self-heating behavior will depend on the state of oxidation of the sulphides as well as time, temperature and humidity. A review of available testing apparatuses and protocols that can be used to assess self-heating potential is presented. Each of these methodologies was examined in relation to its ability to predict the latent self-heating hazard of a sulphide material. Several of the methods were compared to illustrate their strengths and weakness. The results indicated that a number of the test protocols may produce false negative indications of self-heating potential, constituting an obvious concern to the industry.

Jan 1, 2014

By S. Koski

The Cerro Verde copper-molybdenum porphyry mine, majority owned and operated by Freeport- McMoRan Copper & Gold, is located 30 km southwest of Arequipa Peru. The concentrator, which produces copper and molybdenum concentrates, started operating in late 2006 with a 108,000 tpd design capacity, processing primary sulfide ore (mainly chalcopyrite and molybdenite). Plant capacity was recently increased to 120,000 tpd. The comminution circuit consists of one 60? x 113" primary crusher, four MP-1000 secondary crushers in closed circuit with dry screens, four 2.4m x 1.6m High Pressure Grinding Rolls (HPGRs) in closed circuit with wet screens, and four 7.3m x 11m gearless ball mills in closed circuit with cyclones. The HPGR circuit is fed by the Secondary Crushing circuit product at a T80 of 35 millimeters, and the HPGR circuit product feeds the Ball Mill circuit at a T80 of 3000 microns. This paper describes operating experiences with HPGRs during these first four years highlighting improvements in operating practices and presentation of data regarding operational efficiencies, also discussed are the primary benefits provided by HPGRs such as production of micro fractured particles, reduced ore Bond Work Index, and reduced power consumption. Cerro Verde represents the first installation of HPGRs in both the copper industry and large scale hard rock mining.

Jan 1, 2012

By M Edwards

The paper outlines the successful application of some of the on-belt technologies available from Scantech International Pty Ltd and how these have provided benefits in a number of mining and mineral processing operations. Effective process control requires real time analysis so quality can be fed back to the previous process and fed forward to a subsequent process. A range of on-belt analysers that allows for full stream, continuous, non-contact analysis of conveyed materials is available to achieve this. Real time results can provide timely information for effective process control. Benefits of on-belt analysis systems become more evident once the true variability of material quality and moisture content in conveyed flows is measured. To obtain economies of scale in mineral processing operations large material flows are achieved using conveyors. The cost and effort to sample representatively increases as conveyor flows increase. One sample may represent a few tonnes or up to 10 000 tonnes of material. The turnaround time between sampling and availability of sample analysis data does not allow real time process control. Tonnage flow rate, moisture content and elemental or mineralogical composition are required to perform effective process control of most conveyed streams. Tonnages can be effectively measured using belt weighers. The analyses derived from small samples supplied by conveyor-based sampling systems contain high variability. On-belt, continuous analysers see all the material and, through short term compositing of analyses, supply less variable results. Real time analysis helps operators develop a better understanding of material variability. Analysers can be effectively utilised to improve the consistency of product quality through bulk sorting and blending control. Many existing users of the technologies have gained competitive advantages through their ability to supply a more consistent quality product to the market.

Jan 1, 2008

By Ludwig Schmidt

The petroleum industry has recently shown sucks great interest in the evaporation of crude oil and of gasoline, and in the prevention of evaporation losses that almost daily there is being developed and placed on the market equipment designed especially to reduce these losses. Among the recent developments is a new type of tank roof known as the "floating roof," which practically eliminates the vapor space over the surface of the oil, thus removing one of the chief causes of evaporation. There are at the present writing at least two types of floating roofs which, while similar in fundamental principle, differ mainly in the method of making contact with the inside shell of the tank. One type of floating roof is known as a floating tank deck, and has on its circumference flexible metal baskets containing gravel that .rest against the inside shell of the tank. In the other type of floating roof contact with the tank shell is made by the use of movable buffers or shoes. These are attached to the outer ring of the roof and are pressed against the tank shell by means of springs.

Jan 1, 1923

By E. Fregeau-Wu

To recycle steelmaking slags for their iron, manganese, and lime contents, removal of the phosphorus-bearing dicalcium silicate and calcium phosphate is essential. Slow-cooling of slags was necessary to promote the sufficient grain growth to achieve liberation. In-situ grain size distribution determination showed that a high soaking temperature, a long soaking time, a very slow cooling rate, and the addition of fluorspar were shown to promote grain growth. High gradient magnetic separation on slow-cooled slags removed much of the dicalcium silicate. Liberation modelling was used to discuss the breakage and beneficiation characteristics of the slow-cooled slags.

Jan 1, 1992

By Lenny Winkel

With the aim to develop a solar-driven process for the extraction of copper from sulfide concentrates research on the decomposition of copper sulfides under inert atmospheres has been initiated. Thermogravimetric measurements on chalcocite (CuzS) revealed that copper is formed already at 1823 K. Chalcopyrite (CuFeS2) also disintegrates at this temperature, although at a lower rate. Copper and iron have been identified in the solid residue. The results confirm the feasibility of copper extraction by direct decomposition of sulfides under atmospheric pressure. The decomposition under inert atmosphere prevents generation of SO2, it also alters the behavior of volatile impurities during decomposition of copper sulfide concentrates. Chemical eqUilibrium calculations for chalcopyrite contaminated with enargite (Cu3AsS4) have shown that the absence of an oxidic slag allows for a complete evaporation of arsenic and subsequent separation from intermediate sulfides. The need to better assess the potential of direct sulfide decomposition has prompted the development of an experimental setup for studying the decomposition reactions. The experiment has been devised such that data on the decomposition kinetics and on impurity removal can be obtained at temperatures up to 2500 K.

Jan 1, 2003

By T. Plikas, T. Porretta, M. Al-Dojayli, B. Pretorius, J. Woloshyn, H. Ghorbani

"Water-cooled ducts represent an integral part of high temperature off-gas systems in metallurgical processes. Typically, off-gas enters these ducts at significantly elevated temperatures; therefore, water cooling may be required to maintain the duct skin temperature within allowable design limits. These off-gases are typically of high mineral content that could lead to dust buildup, and there is a possibility of slag buildup / molten metal splashing. Therefore, dust cleaning provisions may be necessary in order to remove or minimize accretion on the duct wall, which could otherwise impact the water cooling and the system process efficiency. These ducts may have complex geometry and experience a wide range of loading, including gravity loads, water and gas pressures, cyclic thermal loading and dynamic impact forces. Consequently, the thermo-mechanical assessment of such water-cooled ducts is critical and requires consideration phenomena such as high temperature gradients, potential nucleate boiling, thermal ratcheting and fatigue failures. Such assessment is not comprehensively covered by design-by-rule design codes and guidelines due to its complexity. This paper presents a successful implementation example of design-by-analysis methodology to improve the design and extend the life of a water-cooled furnace transition duct using Computational Fluid Dynamics (CFD) and Finite Element Analysis (FEA).INTRODUCTION Water-cooling represents an important part of high temperature off-gas systems in metallurgical processes. Typical temperatures of the off-gas in the furnace uptake are in excess of 1400°C, and thus there is a need to maintain the water-cooled duct and jacket skin temperatures within their material allowable design limits. Water-cooled channels have been used effectively in arc furnace roof design (Sosonkin et al., 1972; Smolyarenko and Khainson, 1988) and other furnaces as well as in furnace fuming jackets (Scholey et al., 1994). The design of these systems was based on one-dimensional analysis to ensure sufficient cooling is available under extreme furnace conditions (Smolyarenko and Khainson, 1988; Scholey et al., 1994). With advancement in furnace and fuming system designs, water-cooled duct designs have become more complicated in geometry. Numerical techniques, such as three-dimensional fluid flow and heat transfer modeling, are therefore needed to more accurately calculate water velocity, temperature and convective heat transfer coefficients in the water-cooled channels (Haywood et al., 2002; Henning et al., 2010). This is of particular importance around geometric corners where stagnant water flow may lead to local nucleate boiling at the critical heat flux, causing hot spots (Bergman et al., 2011). High wall skin temperatures increase the risk of failures due to thermal stresses as well as increasing corrosion rates (Gelfi et al., 2012), leading to costly equipment downtime and potential safety risks."

Jan 1, 2017

By A. S. Macfarlane

"SynopsisMetal accounting and reconciliation is an increasingly important governance issue in all mining operations, in that it is required, from a risk management perspective, that the company is in control of its product throughout the whole mining value chain. Reconciliation is a grossly misunderstood term. It means different things to different people, and therefore one of the purposes of this paper is to ensure a holistic and integrated understanding of ‘reconciliation’.Previously, where reconciliation was done, it was often for internal control purposes and loosely applied, sometimes with a low degree of confidence and understanding of the underlying parameters and their natural variability.In most mining operations, issues such as dilution, stope performance, and recovery are critical to profitability and long-term value, and thus understanding and control of these key value drivers is essential, not only from the governance perspective, but also from the perspective of maximizing shareholder returns. In order to implement a system for metal accounting and reconciliation, it is important that the cause and effect of these value drivers is understood, and that a systematic control system be established.While a number of off-the-shelf solutions exist for this work, it is the contention of this paper that a full understanding of the metal flow, its variability, its underlying loss potential, and its control points is necessary before a systematic approach to reconciliation can be undertaken.The paper also advocates that this approach should ensure that the reconciliation system clearly addresses the reconciliation needs, within a consistent framework. Such a framework has been developed by AMIRA, in terms of a metal accounting code. However, up until now, this code has been aimed at plant processes, whereas this paper shows how the concept can be extended to cover the full reconciliation requirements for a base metal mine.IntroductionReconciliation is defined as ‘the process of finding a way to make two different ideas, facts, etc., exist or be true at the same time’. In terms of a mining process, this refers to the comparison of measures and estimates along the value chain, and at different points in time, in order to track and optimize metal recovery. This leads to the notion of having a system in place for accounting for the metal. The University of Cape Town defines metal accounting as ‘… the estimation of (saleable) metal in a mine and subsequent process streams over a defined time period. Comparisons of estimates, from different sources over a specific time period, are called reconciliation.’Traditionally, metal accounting has consisted of geological reconciliations of mineral resource to mineral reserve conversion, mine planning reconciliation related to the reconciliation of long-term plans to short-term plans, grade control reconciliation of head grades to sampled or block grades, and mine survey reconciliation of tonnage discrepancies and mine call factors. In addition, metallurgical reconciliation has tended to be based on metal balancing, followed by some commercial metal accounting that links dispatched product to sales quality, quantities, and revenues. Miners disparagingly refer to this plant process as ‘millmatics’."

Jan 1, 2015