Search Documents

By Vanessa M. Torres

Cia. Vale do Rio Doce is currently developing Niquel do Vermelho Project. The laterite deposit is located at Carajas Mineral Province at less than 15 km from Sossego Copper Project, scheduled for start-up in 2004. The available infrastructure, includes paved roads, large capacity railroad and port complex owned by CVRD, power supply and good quality water. The project was evaluated in the past for ferronickel production. In the late 1990s, CVRD switched its attention to investigating the usage of pressure acid leaching. The combination of good metallurgical behaviour for pressure acid leach (PAL) process route with reasonable mineable grades, and existing infrastructure justified the start of engineering studies in 2002. The project approach at the engineering phase is based on the dual objective of minimizing risks while maximizing project profitability and value. CVRD is currently completing the Niquel do Vermelho prefeasibility study. This paper outlines the main outcomes of the study and future perspectives for the project.

Jan 1, 2004

By Ing. R. Geutskens

Zinc-bearing dust from blast furnace gas-scrubbing operation is a well known environmental health problem in the iron and steel industry. Hoogovens IJmuiden (The Netherlands) developed processes to solve this problem. 90% of the zinc is concentrated in 25% of the dust (the fine particle fraction) by means of slurry-hydrocyclonage. The resulting fine particle fraction is treated in a pressure leaching process. Hydrochloric waste pickle liquors have been used as a leaching liquor. By creating optimal leaching conditions more than 98% of the zinc is brought into an acid' solution, whereas nearly all the iron remains in the residue. The zinc can be separated selectively from the solution. The residue can be reused in the blast furnace (via the sintering plant). In the article information is given about the research work and -results of the pressure leaching process as well as the possibilities of the process for solving comparible problems.

Jan 1, 1990

By Gilbert M. Farrior

The electrical resistivity the coefficient of electrical resistivity the Hall coefficient, and the absolute thermoelectric power were determined in this Bureau of Mines investigation for nine compositions of the TiB2-CrB2 sub-system. The numerical values of the electrical resistivity and the thermo-electric power were greater for the intermediate compositions than for the end members. The absolute values of the Hall coefficients and the coefficients of electrical resistivity were less for the intermediate compositions than for the end members. The electrical resistivities and Hall coefficients were about the order of magnitude of most metals--from 34 to 202 microhm-cm and from about 0 to -23.3 X 10-4 cuP/coulomb. The thermoelectric power was somewhat greater than that of most metals--up to 15.6 microvolts per 0 C.

Jan 1, 1965

By N. W. Stump

New developments in on-stream analysis using immersed radioisotope gauges including results from plant installations are described. The control of grinding and flotation using a small digital computer has been complemented by this development. A control scheme for grinding which is based on maximum throughput at constant product size and preliminary work in flotation control are also outlined.

Jan 1, 1974

By M. Pierce, E. Karampinos

"One of the main challenges in the numerical modelling of ground support in underground excavations is to reproduce the performance of the sequential installation of the reinforcement while capturing the rock mass behaviour of an advancing face in 3D. The 3D modelling approaches used to simulate the progressive advance of excavations are mostly continuum and often cannot reproduce the rock mass failure mechanisms. The 3D discrete element method (DEM) can better reproduce structurally controlled rock mass failure mechanisms and can explicitly represent the reinforcement elements. This paper builds on previous work that reproduced the structurally controlled squeezing conditions in an underground hard-rock mine using 3D DEM and the in situ behaviour of reinforcement under pull conditions. It addresses important issues on the way reinforcement is explicitly introduced in discrete element models. A pseudo-3D model is employed to overcome the computational restrictions and time limitations of a 3D modelling approach. The work focuses on the scaling of the material properties of the ground support elements when the thickness of the model is not equal to the out-of-plane spacing of reinforcement. It demonstrates the scaling methodology based on the type of the modelled reinforcement elements used and investigates the significance of this approach. The advantages and disadvantages of this approach with respect to 2D and 3D methods are discussed. The results are compared with field data and previous modelling work done at the mine. IntroductionNumerical models can provide significant insight into the anticipated behaviour of underground excavations. The modelling of ground support, however, is not a trivial exercise. An effective representation of ground support in underground excavations should capture the behaviour of both the rock mass and the support elements. When numerical models are used for design purposes, the complexity of the problem requires significant time and expertise (Sweby, Dight, and Potvin, 2016).At a laboratory scale, numerical models have successfully reproduced the results of laboratory tests on rockbolts by explicit modelling of the bolt, the borehole, and the grout. Chen and Li (2015) used a continuum FLAC3D (Itasca Consulting Group Inc., 2012) model to simulate the mechanical behaviour of D-bolts as observed experimentally. Grasselli (2005) used a 3D finite element code to model the behaviour of fully grouted rods and expandable bolts under shear."

Dec 1, 2018

By Reece Kurre, Gabriel Walton

"Roof bolting has long been used in underground mines across the world to provide ground support. Modern roof bolts are cheap and easy to install with the use of specialized machines as a part of the production cycle. Lhoist North America’s Crab Orchard Mine is an underground room and pillar limestone mine that uses mechanically anchored roof bolts for ground support. The mine currently employs two different roof bolting patterns: a standard 5 × 5 foot pattern, and a 2.5 × 2.5 foot pattern for use in areas with particularly hazardous roof conditions. The purpose of this study is to evaluate the relative effectiveness of each bolting pattern.A series of numerical models were created using RocScience’s RS2. The models were based on a symmetrical section of the mine at its deepest point, and were modeled using Generalized Hoek-Brown failure criterion along with a discrete fracture network. A series of sensitivity analyses were performed on the models by varying parameters such as joint friction angle, crack persistence, joint randomization, and tensile strength of the limestone. Based on the results of the original models and sensitivity analyses, it appears that the standard bolting pattern provides sufficient roof support capacity under almost all the expected conditions at the mine, since factors of safety below the design value of 1.5 were only found for individual bolts in a few of the worst test cases considered. These results can help improve the Mine’s productivity and reduce operating costs without compromising safety.INTRODUCTION AND CASE STUDY DESCRIPTIONLhoist North America’s Crab Orchard Mine is an underground limestone mine located in Crab Orchard, Tennessee. The mine is located under an 800-foot-high mountain, and outcrops on three sides. The mine is accessed through three separate portals and has two main levels, along with a partially developed third level. Extraction is accomplished by the room and pillar method using 50 × 50 feet pillars and 50 × 50 feet rooms. The mining height is limited to 50 feet to keep the pillar width to height ratio around 1.0. Each heading is excavated in a two-stage process that consists of a 30-foot-tall top heading and a 20-foot-tall bench. A distance of at least 30 feet is maintained between the two levels at all times (Crab Orchard Mine Technical Staff, 2017)."

Jan 1, 2019

By K. van Netten, T. P. Ernst

"Froth flotation has been used successfully for about a century in the beneficiation of both coal and mineral particles. With the on-going trend towards lower feed grades, however, there is a need to transform this technology in ways that can deliver ultrafast separations, with strong selectivity, and recovery, covering a broader size range. It should be recognised that the hydrophobic effect, with its highly selective and long-range interactions, will most likely underpin any new technology. We identified the separation of the concentrate from the tailings as the rate determining step of conventional flotation technology. This limitation was then addressed by developing a novel flotation technology, insuring the formation of a concentrate that could be separated more rapidly from the tailings. We introduced a novel binder medium, a highly concentrated water in oil emulsion, to act as the focal point for hydrophobic adhesion, effectively replacing the air bubbles used in conventional flotation. The hydrophobic particles adhere to and become embedded within the binder, forming saturated agglomerates that float upwards. Moreover, by forming these large and resilient agglomerates, the product can be quickly dewatered over a screen and separated almost immediately from the tailings. Remarkably, this new binder permits residence times in the order of a few seconds under batch conditions. This paper examines the performance of the technology as a function of the oil wt% added to the slurry. The paper also examines the performance of the technology as a function of the particle size, showing a decline as the particle size exceeds 0.50 mm.INTRODUCTIONFroth flotation involves the collision and adhesion of hydrophobic particles to rising air bubbles, the carrying of those particles from the bubbly-pulp zone into a froth zone, and subsequent drainage and migration of the pulp to achieve the final concentrate (Wills, 2006). Within a Jameson Cell the feed slurry and air bubbles are brought into intense contact within the active area of the downcomer, achieving rapid kinetics of hydrophobic particle adhesion to the air bubbles (Harbort et al., 1994). However, once the bubble laden product and tailings emerge from the downcomer there is the need for separation of the concentrate from the tailings, an inherently slower process. In other devices such as mechanical cells the initial kinetics of particle adhesion are far slower, relying on the turbulent eddies throughout the cell, while in a column the kinetics rely upon an even slower process of bubble interception with suspended and settling particles (Gorain, 2007). However, in all cases the driving force for segregating the bubbles from the tailings, and the drainage of the froth are inherently the same. We do note, however, recent advances by Galvin and co-workers in achieving so-called Fast Flotation, utilizing a system of inclined channels to dramatically increase the segregation rate of bubbles from the tailings, permitting much higher gas and feed fluxes to be applied, achieving up to a ten-fold throughput advantage (Dickinson et al., 2014). Any further improvement within the existing flotation paradigm would require the introduction of centrifugal forces, but this would also require the formation of much finer bubbles than is typically used given the tendency of relatively large bubbles to reach a limiting slip velocity due to deformations and increased drag. Across all flotation devices we argue the rate determining step remains the segregation of the bubbles from the tailings."

Jan 1, 2016

By Ralph D. Parker

THE subject matter of this paper will be primarily restricted to the metallic mineral industry, which last year was responsible for almost 60 per •Cent of the total value of Canada's mineral production. It has been written that, in the broad sweep of eternal time, sixty years is as transient as a flicker of lightning in a summer night's sky. In the history of mankind and human endeavour, however, six decades can encompass momentous events and far-reaching •circumstances, all of which affect the lives of men and change the destiny of nations. This observation is con-firmed very positively by a study of our Canadian mining history, from either the broad viewpoint of human progress or the more specialized viewpoint of national economy. The past sixty years have witnessed vast changes in the economic importance of mining in this country's affairs, and also in the technology of the industry. Mining has emerged from the days of rule-of-thumb practice and is now taking on the stature of a highly diversified science.

Jan 1, 1962

By P Navarra, R Kuhne

Dynamic simulation (discrete event simulation) is the preferred methodology to evaluate the impact of dynamic aspects of processing plants on the overall plant capacity. This tool can be used to: identify bottlenecks in the plant,justify upgrade and expansion projects by evaluating their impact, oroptimise maintenance and operating practices without disrupting the operation. Iron Ore Company of Canada's (IOC) pelletising plant is a complex operation because of multiple products, varying equipment capacity and shifting bottlenecks. Furthermore, with extensive capital requirements for projects and long lead times, a high level of confidence in project outcome is required. Therefore, a model of IOC's pelletising plant in Labrador City was constructed in 2007 by a joint IOC and Hatch team. The model includes both operational and metallurgical aspects in order to better capture the complexity of IOC operation. In this paper, the justification, boundaries, and functionality of the model are described. A comparison of simulation results to historical plant operation is given. It is observed that projects have interactions and that the benefits of combined projects are not equal to the combined benefits of the individual projects. Projects can have synergies that result in greater benefits when combined or can have overlapping benefits that result in lower benefits when combined. The power of the proposed modeling exercise lies in the ability to assess the impact of projects on overall performance.

Jan 1, 2009

By Thomas T., Read

THROUGHOUT the Colonial era, Philadelphia was easily , the leading city of North America, and it still held that position at the end of the period, with a population of about 25,000, though closely pressed by Boston, which had slightly over 20,000, and New York, which had nearly as many. It was the center of a region in which mineral industry was important. Thomas Rutter's bloomery, built in the Schuylkill valley in 1716, was quickly followed by many others, and during the Colonial period at least 20 blast furnaces, 45 forges, and iron- works of other types were built in eastern Pennsylvania, which easily led all the other colonies in iron manufacture. During the Revolutionary period others were erected as far west as Fort Loudon, in the Cumberland c alley.^ After 1800 the rapid development of the anthracite mining industry profoundly affected Philadelphia's, development, since transportation of the coal was then necessarily by water, and the streams of the anthracite . regions mostly flowed into either the Schuylkill or the Delaware Rivers. With an abundant near-by supply of coal and iron, with the seat of government, which had been there since 1774, and with a National Bank established there in 1791, one would have seemed safe in prophesying, at the beginning of the nineteenth century, that Philadelphia would permanently remain the leading city of the United States. Education in Philadelphia was at first wholly in the hands of the Quakers, who had established a "Public School" there in 1689, but in November 1739 George Whitefield, who had created a sensation in England by his preaching, though only 24 years old, passed through Philadelphia on his way to Georgia to found an orphan school there. He preached a series of sermons in Christ Church that were so disturbing to the established church that on Nov. 25 the Rev..Richard Peters (who was also Provincial

Jan 1, 1941

By Michael A. Krstich

A soil washing pilot plant to treat soils at the U.S. Department of Energy (DOE) owned Fernald Environmental Management Project (FEMP), was designed based on extensive bench-scale testing. The system's design incorporated a combination of physical separation and' chemical extraction processes and was tested on two soils. The textural composition of the two soils was approximately 20 percent sand, 60 percent silt, and 20 percent clay. Since this grain size distribution was not considered optimum for physical separation techniques, thesoil washing pilot plant had to be designed with selected equipment to provide specific soil size fractions during processing operations. A trommel, vibrating screen deck, centrifuge, and attrition scrubber were used in the system to selectively separate specific soil size fractions at 4.75, 2, 0.3, and 0.02 millimeters (mm). The trammel used high pressure water [1000 pounds per square inch (psi)] during the initial step of the process to reduce soil aggregates to single grain composition, separate out greater than 4.75 mm gravel, and dislodge chemical contaminants from the individual soil particles. The vibrating double-screen deck provided 2 - 4.75 and 0.3 - 2 mm soil fractions that, when combined, averaged greater than 75 percent solids for both soils. The centrifuge was designed to take the less than 0.3 mm soil slurry from the screen deck and produce a particle size of 0.02 mm. The centrifuge produced a high solids stream that averaged greater than 70 percent solids for both soils. These 0.02 to 0.3 mm soil solids from the centrifuge were combined with the 0.3 to 4.75 mm soil solids from the screen deck and processed through the attrition scrubber. The data collected from the pilot-plant operation was used to aid in the design of a full-scale system and was instrumental in formulating full-scale process operations and the selection of equipment.

Jan 1, 1995

By S. Chander

A series of nonionic and anionic surfactants were tested to enhance the flotation response of a low rank coal. An ethoxylated octyl phenol and several polypropylene polyethylene block copolymers were tested as nonionic surfactants. The anionic surfactant was a dioctyl sulfosuccinate. All the surfactants employed improved the yield significantly but the influence on grade was complex. Separate studies were conducted to determine the emulsification behavior of the surfactants. For the nonionic water soluble reagents tested, a correlation between emulsifying power of the surfactant and flotation was observed. An increase in the number of droplets produced in surfactant containing systems was considered to be the main reason for increase in the yield. Since it increased the number of collisions between dodecane droplets and coal particles. When a surfactant was introduced into the flotation pulp prior to addition of dodecane, it decreased the benefits of the surfactant significantly. The decrease was attributed to an increase in the wettability of coal and a decrease in the surfactant available for emulsification. When a suitable surfactant was added as a solution dissolved in the oily collector, a considerable increase in yield was observed.

Jan 1, 1993

By P. James

Blue Planet Strategies (BPS) focuses on improved resource utilization and targets converting wastes into resources. New BPS capability (DEMET) wrings extra value from mining and processing wastes by enabling new production from waste and residual sources. This powerful platform technology provides considerable processing flexibility and enables various new economical treatment options to extract key metals from low level and process byproduct stream sources normally left as waste by traditional processing methods.[1]

Feb 23, 2014

By O. Hall

STOPING at Noranda" is a sequel to "Mining at Noranda". "Mining at Noranda", presented in 1937 (1), sketches Noranda's history, metallurgical problems, exploration, mining methods, mining details, pillar extraction, and costs. "Stoping at Noranda" deals in greater detail with our stoping, the use of sub-level drifts instead of benches, and the drilling out of the stopes with jointed rock drill steel and diamond drills. Sun-LEVEL DRIFT STOPING: Sub-level drift stoping is almost universal throughout the mine and is the standard sroping method in both sulphide ore and rhyolite flux ore. The features that have led to the adoption of this standard are: (1) Continuous symmetrical drilling in sub-level drifts with no delay for blasting. (2) Large-tonnage blasts Saturday night after the drillers have left. (3) Comparative freedom from gas and smoke during the working days. ( 4) The daily safety achieved by having all stope drilling done in drifts. (5) The safety and security achieved by drilling out stopes, floors, and pillars before there is any weighting or cracking.

Jan 1, 1939

By William Petruk

A fully automatic image analysis system that consists of a microprobe, an energy dispersive x-ray analyzer, and an image analyzer was developed at CANME:I' to determine mineral behaviour that affects beneficiation. The interlacing between the instruments permits automatic identification and characterization of minerals in samples of unbroken ore pieces and of mill products. Different types of information are obtained for minerals in samples of unbroken ore pieces than in samples of mill products, and are used differently. For unbroken ore pieces size distributions are determined for discrete mineral grains to predict a grind at which they might be liberated, and other measurements are Irade to predict the percentage of mineral that occurs as nonrecoverable grains. For mill products the minerals are analysed to determine percentages that (1) are free, (2) are likely to be recovered in concentrates, (3) are likely to be lost to tailings, and (4) could be liberated with regrinding. The image analysis data for mill products are processed by a mineral-metals balance program to determine the distributions of free and unliberated mineral grains at each point in a concentrator, pilot plant or bench test. For samples containing trace minerals, such as gold, an automatic search technique is used to scan the entire area of the polished section for the trace mineral grains. The identified trace mineral grains are characterized with regard to size, liberation, and other properties.

Jan 1, 1988

By John M. Hird

Texas Gulf Sulphur Company's Lee Creek Mine has opened a major phosphate mining district in the Central Coastal Plains of North Carolina (Fig. 1). The ore deposit as it is now known was roughly outlined in 1961 by a Texas Gulf geologist using wire line exploration methods. Slightly uraniferous phosphate materials were detected by a slim-hole gamma ray probe run in numerous farmers' water wells penetrating the formations. A follow-up-core drilling pro- gram determined the economic ore limits to lie in the south central section of Beaufort County beneath 70 feet to 120 feet of unconsolidated sediments. The 50,000 acre deposit is known to contain over two billion tons of phosphate ore amenable to strip mining methods. A part of the deposit underlies several thousand acres of the Pamlico River estuary. The 90 million dollar capital investment plant built by Texas Gulf during 1965-66 included a strip mining operation using a 72-yard walking dragline, a three million product ton per year flotation concentrator, four fluid bed calciners, a sulphuric acid plant (acid for captive use), a phosphoric acid plant, and three solid fertilizer material plants. Shipment to domestic markets is by rail and truck and to over- seas markets by barge to a transshipment terminal at Morehead City, North Carolina. Early mining investigations were conclusive first that the phosphate ore could economically be recovered only by dry strip mining methods, and second that artesian ground waters in the formation (Castle Hayne limestone) underlying the ore would have to be controlled. This report will relate the application of ground water hydrology in depressurizing the Castle Hayne aquifer to facilitate dry strip mining at depths 130 feet below sea level at the Lee Creek Mine.

Jan 1, 1970

By Z. T. Bieniawski, R. K. Zipf

"Zipf Jr., R.K. and Bieniawski; Z.T., 1989. A fundamental study of respirable dust generation in coal. Min. Sci. Technol., 9: 87-99Black lung disease in coal miners induced by the formation of fine fragments of coal imposes very high human and direct costs. A fundamental understanding of the fracture processes leading to fine-fragment formation in coal by applying principles of fracture mechanics is presented. A four-step hypothesis is proposed which sequentially describes the mechanics of fine-fragment formation during a generic coal material—coal cutting tool interaction. These steps include: (1) development of a crush zone under the tool tip, (2) macrocrack propagation. (3) shear movement along macrocracks, and (4) additional fragmentation from shear. This model contains two sources of fine fragments, namely crushing under the tool tip and shearing along the macrocrack surfaces. Three critical assumptions are made that require experimentation. First, the coal material must contain flaws of sufficient density and sufficiently small size to liberate fine fragments by crushing. The following conceptual relationships are proposed between flaw size, spacing and fragmentation: first, the active flaw size must be less than the desired particle size and second, the spacing (or density) must be in the order of the particle size. The second major assumption is that a mixed mode fracture theory will describe the initiation and crack growth direction for the microscopic inherent flaws. The third assumption is that some degree of roughness damage, and interlocking exist along the newly formed macrocrack surfaces such that a small amount of shear movement along that surface leads to additional particle formation at a microscopic scale. Preliminary analysis of the mechanical regime under a cutting tool tip places order of magnitude bounds on the stresses strains, cycle time, stress rates and strain rates. Even though the tool moves and loads the coal material with considerable speed, a quasi-static stress analysis is applicable in this region.Introduction.The generation of fine fragments (respirable dust) during various coal mining processes may lead to the incidence of coal workers pneumoconiosis (black lung disease). The human and direct cost of dust-induced illnesses in coal miners is very large. By several. accounts [1,2] the Federal Government paid out about $12 billion to almost 500,000 coal miners and their beneficiaries between 1970 and 1980. In addition, several states and many coal operators have established their own compensation programs at costs ranging from a few cents to several dollars per ton of coal mined [2]. Since 1980, 'the present liability of the Federal disability trust fund has approached $20 billion and the benefit payments exceed $1 billion per year. There .are also hidden costs due to dust, in the form of increased equipment wear and decreased operator productivity, both of which are due to the poor operating environment. Quantifying these costs may be difficult; however, they may be in the same range as the present pneumoconiosis costs. These high human and direct dollar costs may be prevented or reduced through long term research efforts directed at understanding the generation and control of respirable dust and the incidence of black lung disease."

Jan 1, 1989

By S J. Hawke, L A. Dominguez

In non-ferrous metal mining operations, it is generally necessary to crush and grind the ore to a very fine particle size to effectively liberate the contained mineral from the host rock. Fragmentation by blasting is the first stage of this comminution process.Numerous studies and independent modelling of the Mine to Mill process have demonstrated the potential for significant downstream productivity improvements from improved blast fragmentation. However, safety and environmental constraints associated with the blasting process usually limit the extent to which blast energy or powder factor can be increased.An effective blasting solution has been identified that enables the safe utilisation of powder factors several times higher than those used conventionally to provide significant improvements in fragmentation. The solution uses a static ‘blanket’ of broken rock overlying the blast to contain this increased blast energy and control rock movement. To produce this broken layer of rock, the subdrill in each blast is significantly increased to preblast (or precondition) the entire stemming region of subsequent blasts on the next mining bench.The solution has been evaluated at a large open cut poly-metallic mine in Mexico. Results from the application of this technique have shown significant improvement in run-of-mine fragmentation, with subsequent downstream productivity improvement indicated.CITATION:Hawke, S J and Dominguez, L A, 2015. A simple technique for using high energy in blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 321–326 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Emil B. Milosavljevic, Ljiljana Solujic

Cyanide is exceptionally reactive, and in typical gold/silver processing liquors, cyanide may be transformed into various species and forms depending on the mineralogy of the ore and chemical make-up of the process water. The exact speciation and relative concentrations depend on the Eh and pH values, as well as the free CN concentration in the system. Very good cyanide balances can be achieved by the judicious selection of the analytical techniques used. The choices an analyst has to make (which analytical methods to use and which ones to avoid) in order to gain better understanding of cyanide speciation and balances in a particular system under investigation will be discussed. Examples of cyanide balances obtained for the laboratory scale tests (agitated leach and column tests) will be presented and discussed.

Jan 1, 1999

By A. L. Nunes, J. R. E. Garcia, G. Silva, U. Prasad, C. Rabe

"Drilling through the Guayabal shales, a gray calcareous shale, and the C1 to C100 formations, a well-cemented calcareous-sandstone in Corralillo field, Mexico, is a challenge due to severe wellbore instability problems. Additionally, there has been a history of ineffective reservoir stimulations by hydraulic fracturing. To predict and mitigate these subsurface issues, it is essential to characterize the mechanical properties and rocks strength for a better prediction of borehole stresses and collapse pressure during drilling. Various correlations can be used to estimate and/or determine the unconfined compressive strength but most of them are based on transit time and porosity.In this study, grain size distribution was combined with acoustic travel time, porosity and static Young’s modulus to develop a rock strength prediction model for the turbiditic sandstones of the Chicontepec basin. The main reason this combination of parameters was employed was because of the wide variations in rock strength estimated using traditional porosity-based correlations such as the McNally’s (1987), GMI-Jizba-E’s and Bradford’s (Bradford et al., 1987).To develop a new correlation, a geomechanical and microstructural campaign was initiated. Mineralogy by X-ray diffraction, pore and grain sizes by petrography, clay distribution by SEM and porosity by mercury intrusion porosimetry were measured. Static and dynamic Young’s moduli and Poisson’s ratios were acquired by triaxial and ultrasonic measurements on undisturbed sandstone samples from the Chicontepec basin. More than ten offset wells with wireline data, including transit time, porosity, density, resistivity and gamma ray, were used for reservoir and geomechanical characterizations.Our analyses lead us to propose a new correlation for predicting the uniaxial compressive strength (UCS) of sandstones of the Chicontepec Basin as a function of transit time and grain diameter, both of which can be derived independently from destructive laboratory tests. Our results also highlight the importance and value adding of a combined approach incorporating grain size analysis in the rock strength prediction. The UCS predicted using the transit-time and grain-size-based model presents a median value (P50) of 76 MPa, P10 of 55 MPa and P90 of 89 MPa."

Jan 1, 2015