Search Documents

By Matthew Grzelak, Gulsah Erinc, David R. Chapman

"The third phase of the Bagram Drainage System project at Bagram Air Force Base in Afghanistan included construction of a shallow, 540-m long, 1.8-m inside diameter drainage tunnel. The tunnel penetrated mostly stiff to hard clayey and silty soils. The contractor’s Value Engineering Change Proposal (VECP) to use pipe-jacking with a microtunnel boring machine (MTBM) instead of the specified two-pass Earth Pressure Balance method was evaluated and supported using hand calculations. Contractor support was provided throughout the project by providing design reviews and instrumentation monitoring during construction. This paper compares the value-engineering proposal to the specified method and describes the construction conditions encountered. INTRODUCTION As part of a larger improvement project at the Bagram Air Force Base in Afghanistan, a shallow, 540-m long, 1.8-m inside diameter drainage tunnel was constructed to provide additional capacity for Coyote Creek to pass below several critical structures, including taxiways and the main runway, for mitigation of recurring flooding (see Figures 1 and 2). Overburden over the tunnel crown ranged from about 3 m to 5.5 m. An existing cast-in-place twin barrel concrete culvert runs approximately parallel to the new tunnel and is within about 8 m at its closest point. The contractor’s Value Engineering Change Proposal (VECP) to the specified two-pass Earth Pressure Balance (EPB) method (steel ribs and lagging or steel liner plate with a carrier pipe later grouted in-place) called for installation of the required drainage pipe by pipe-jacking (one-pass installation) using a slurry microtunnel boring machine (MTBM). The critical nature of the operations at the air base resulted in significant construction coordination challenges and a greater than usual need to avoid excessive settlements. Substantial restrictions were placed on drilling of investigative borings and installing instrumentation near runways and taxiways due to drill mast height. The prime contractor was SERKA TAAHHUT INSAAT A. S. (SERKA), the microtunneling subcontractor was Ludwig Pfeiffer Microtunnel GmbH & Co.KG (Pfeiffer), the jacking pipe designer was Gollwitzer Pipe and Shaft Technology GmbH (Gollwitzer), and the contractor’s tunnel engineer was Lachel & Associates, Inc. (Lachel). Lachel provided contractor support throughout the project including preparation of a VECP/Design Summary (including interpretation of existing and new geotechnical information), design reviews for jacking pipe, estimating settlement of an existing drainage structure above the new tunnel, and instrumentation planning, monitoring, and analysis during construction."

Jan 1, 2016

By J. A. Brusset

Introduction The West Canadian Collieries, Limited, operate three bituminous coal mines in the Crowsnest Pass district of Alberta. Two seams are worked; their thickness varies from 10 to 20 feet and their pitch from 10 to 45 degrees. The Bellevue mine was opened in 1903, the Greenhill in 1914; both are gassy and dusty, and at both the haulage is a problem, as the workings are spread over distances of several miles. Compressed-air locomotives are used at Bellevue, rope-haulage at Greenhill, both of which solutions of the haulage problem are costly in installation an operation, and lack flexibility. In 1943, the Adanac mine was opened; and the question soon arose as to which system of haulage should be selected. Compressed-air locomotives and ropes were rejected on the ground of high cost. Since, under the Alberta Mines Act, the use of trolley locomotives underground in coal-seams is not permitted, the choice lay between storage battery locomotives and Diesel locomotives. The preference of the author, who had had experience with both in French gassy coal mines prior to 1930, was for Diesel locomotives, due to lower cost of installation and greater flexibility and reliability. However, Regulation No. 13 of the Mines Act of Alberta reads: 'No gasoline-driven engines shall be used underground in any mine, and no internal combustion engine shall be used underground in any coal mine, except only when authorized by the Chief Inspector in writing, and on such terms as he may prescribe"

Jan 1, 1948

By Frank E. Chase

Retreat mining is one of the most hazardous operations conducted underground. One of the keys to miner safety and an efficient recovery of the reserves is to design adequately sized production pillars to prevent pillar squeezes, excessive pillar spalling, severe floor heave, roof falls, and pillar bumps. Currently, few pillar design approaches are available which consider the abutment pressures generated by the gob. The Bureau of Mines is developing a method called Analysis of Retreat Mining Pillar Stability (ARMPS) to aid in the design of retreating sections. Back analysis of 42 case studies indicates that ARMPS can be helpful in predicting stability during retreat mining operations.

Jan 1, 1993

By J. E. Carr

A bewildering number of continuous thickeners and clarifiers are used in mineral industries and other heavy industries. General types are: 1. Conventional Thickeners (Fig. 1). 2. Thickeners with Flocculating Feedwells (Fig. 2). 3. Solids Contactors (Fig. 2). 4. Tray Thickeners (Fig. 3). 5. Lamellas (Fig. 4). 6. Conventional Thickeners with Lamellas 7. High Flow, Fluid Bed Thickeners (Fig. 5). These units must be adapted to varied applications. They must provide operating flexibility to meet process needs. Such factors multiply the decisions which must be made prior to the selection of a thickener. The seven types of thickeners listed above, with their variations, share design concepts which limit their application and which can be used to evaluate their performance. Some of these are listed: 1. Feed velocities must be limited and/or controlled. 2. Natural or reagent flocculation is necessary. 3. Horizontal settling area is the basis for capacity. 4. Overflow velocities must be limited and/or controlled. 5. A controlled underflow is necessary. Applying these needs to the basic process concepts is thickener selection. The basic function of a thickener in the minerals industry is the separation of a thickened sludge containing fine solids from water. To this primary separation function are frequently added others to give a list as follows:

Jan 1, 1977

By R. D. Brown

"AbstractIn order to raise the enormous amounts of capital which will be essential for the development of Canada's mineral and petroleum resources, this country's resource industry must be permitted to earn an acceptable rate of return. The existing tax regime, with its high rates, complexities and misdirected incentives, presents a serious obstacle to our resource industries in their development of Canada's immense , but increasingly lean, resources. Government tax and other policies are not the only cause of the crisis now facing the resource sector in Canada, but a reformed tax system, with stable and reasonable tax burdens, is required if Canada's resources of minerals, oil and natural gas are to continue to contribute in the future, as in the past, to our national well-being.An independent task force, organized under the auspices of the Canada West Foundation, has recently completed a wide -ranging report: on the future development of Canada's mineral, oil and gas resources. This five-volume report, completed after almost two years of research and study, concludes that Canada •is facing a major crisis •in the development of our resources, It states that unless corrective action is taken now, mineral production and exports could decline drastically after 1985, at the same time that Canada would face massive bills for imported oil because of inadequate and declining production.The task force, chaired by the author of this article, has put forward recommendations for a fundamental shift in both federal and provincial policies in order that Canada's mineral reserves can be developed in the national interest. This article consists of excerpts from the summary of the task force's report."

Jan 1, 1977

By M. Al-Khawaja, F. Hassani, F. Mucciardi, N. Razavinia

"In today’s economy many industries are becoming aware of the need to recover some of the waste heat they create. Industrial processes release, on a global scale, over 100 tera-Joules (i.e. 1014 J) of waste heat annually. The recovery of waste heat can lead to a reduction of greenhouse gas emissions and it can also provide a financial benefit which can be obtained by converting some of this excess heat to electricity. At McGill, a research program has been initiated so that low grade waste heat (temperature between 100ºC and 300oC) from process off-gases found in pyro-metallurgical industries is captured and concentrated by using heat pipes and then converted to electricity by a mechanical engine. This paper illustrates the 3 C’s process (capture, concentrate and convert waste heat to electricity). It also provides some preliminary experimental data. INTRODUCTIONThe problematic climate change caused by the use of fossil fuels, the rapid depletion of global reserves and the catastrophic consequences of nuclear power generation call for renewable and safe, resources of energy, for both man and the environment. Extensive researches in the production of energy from renewable sources and improvements in efficiency of current technologies can help us to reverse this trend.The greatest advantages of using renewable energies are that they don’t deplete and they also contribute to a green environment. On the other hand the disadvantage of using these resources is that the energy available from renewable sources is much less concentrated than that provided by fossil fuels and nuclear energy. This makes renewable energy less attractive for large scale industrial uses in most cases. A key target for society for the 21st century is the production of energy from renewable sources at a cost that is competitive with fossil fuels. Fossil fuels represent a concentrated form of energy; usually it is referred to as high grade energy. Nonetheless, there is a vast supply of alternative energy. The sun, wind, water and biomass were the first to be explored. While these are all valid options that warrant concerted efforts and large investments, there is another source of energy that typically is produced by manufacturing industries. This energy is often referred to as low grade waste heat. Most of this energy is simply vented to the environment through the stream of off-gases. In the future it will be necessary to capture and convert some of the low grade heat to a valuable form such as electricity if we are to improve on the efficiency of energy usage."

Jan 1, 2012

By László I. Kiss, Verena Mackowiak, Alexandre Perron, Dominic Toulouse, Alicia Liedtke, Sándor Poncsák

"Bubbles play a very important role in different metallurgical applications like for example in electrowinning. During heterogeneous nucleation, the maximal size of the bubbles growing at the nucleation sites as well as the nucleation frequency is determined by the so-called detachment condition. Detachment occurs when the external forces acting on the bubble exceed the retaining forces along the solid-gas-liquid triple interface line. The phenomenon depends strongly on the shape and orientation of the solid surface and on the nature and strength of the external buoyancy and drag forces. In the present study the detachment conditions of bubbles from downward facing horizontal and inclined plates were studied experimentally under the effect of gravitational and hydrodynamic forces. The results show the deformation of the bubbles under the effect of the external forces and the detachment conditions as function of the bubble volume.IntroductionIn heterogeneous nucleation bubbles are generated at the so-called nucleation sites along the solid-liquid interfaces. They continue to grow there and after they reached a certain size they detach from the solid surface and leave the nucleation site. This scenario is well known both in boiling and electrolysis. During the growth period a stable equilibrium exists between the forces that retain the bubble at the nucleation site and the forces that try to remove it. This equilibrium evolves with the increasing volume of the bubble to the point when the detachment forces overcome the retaining forces.The life of a single bubble generated by heterogeneous nucleation can be divided into two periods separated by the detachment - or in other words by the departure - of the bubble: first the growth at the nucleation site and then the movement away. The knowledge of the detachment conditions makes possible the determination of the maximal volume of the bubble at the nucleation site that, in tum, makes possible the determination of the nucleation frequency. This is why so many researches have been directed toward the clarification of the details of the bubble detachment in the past decades. The equilibrium between the attaching and separating forces depend on the presence of body, surface and flow induced forces in the liquid, on the geometry and orientation of solid surface, on the properties of the solid-liquidgas system etc."

Jan 1, 2004

By S. Dessureault

The relatively recent explosion of available data in all business sectors has induced a common expression of “drowning in data, starving for information.” The mining sector is affected by the information age through equipment-based sensors, process monitoring, and traditional enterprise data sources. Information technologists have developed techniques such as data mining that apply new and old statistical algorithms to large datasets. Mine planners and managers can apply these tools for improved planning and control, thereby increasing the use of the highly underutilized information system infrastructure in most modern mines. This paper describes the use of data mining and its enabling technology, data warehousing, in the development of an energy consumption model for large surface mines using real historical data.

Jan 1, 2007

By C. Coetzee

Additives are commonly used in copper electrowinning to improve cathode morphology. Polysaccharides such as guar are generally favoured as additives due to their compatibility with solvent extraction. Polyacrylamides are, however, being considered as possible alternatives. Understanding the influence of the structural chemistry of additives on electrowinning performance is critical to utilise them efficiently. This paper investigated polyacrylamide additives which are structurally different; their effects on copper electrodeposition were characterized and compared to that of guar. Electrochemical impedance spectroscopy (EIS) were used to characterize the effects of molecular weight and ionic charge of the polyacrylamides on electrodeposition. The findings were compared against results obtained with an industrially used guar product. Equivalent circuit modelling of EIS data indicated that an increase in polyacrylamide concentration and a decrease in additive molecular weight increased the overall system resistance.

By J Seccatore, G Sadao, M Cardu, G De Tomi, L Finoti, F Galvão, J Romero Huerta, A Rezende, J Bettencourt

In the mining industry, rock blasting can be considered as the first phase of comminution. The downstream phases of comminution are mechanical, and consist in consecutive stages of crushing and milling for grain size reduction. The total energy of mechanical comminution depends on grain size and on the resistance of the material to grindability. Usually, the first is quantified by the grain size distribution or one of its KPIs (such as the diameters X50 or X80), while the latter by the working index (WI), representing the amount of energy necessary to reduce the size of grains of a determined amount of material to the desired equivalent diameter (usually expressed in kilowatt hours per tonne – kWh/t). It is widely recognised that it is possible to manage the output of a blast in terms of grain size distribution varying specific charge (powder factor – PF) and charge distribution; specific algorithms such as the KUZ-RAM or the SWEBREC have been created to predict such output. It has also been demonstrated how higher PFs weaken the blasted material by creating micro-fractures that reduce its WI. This paper focuses on a related aspect: the influence of charge distribution on the specific comminution energy in crushing and milling. Small-scale blasts have been performed on 14 marble blocks with different PFs and charge distribution. For every PF, charges have been designed to simulate concentrated and distributed geometries. Concentrated charges simulate opencast blasts with large-diameter holes, with large burdens and spacings. Distributed charges simulate bench blasts with small-diameter holes and reduced burden and spacing. Three control blocks have been fragmented by mechanical means for comparison. For every sample the grain size distribution and the WI in ball mill has been determined. Results show the correlations between charge distributions and the specific energy of mechanical comminution in milling. Finally, the opportunity of adjusting charge diameters and distributions in opencast blasts to improve the output of the comminution circuits is discussed.CITATION:Seccatore, J, Romero Huerta, J, Sadao, G, Cardu, M, Galvão, F, Finoti, L, Rezende, A, Bettencourt, J and De Tomi, G, 2015. The influence of charge distribution on the grindability of the blasted material, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 749–754 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By T. Sreenivas

This paper describes results of laboratory studies on recovery of dissolved uranium values from alkaline leach slurries of a medium-grade uranium ore from Gogi (Karnataka, India) using the resin-in-pulp (RIP) process. Besides anionic carbonate complex of uranium, the other major ionic constituents of the leach solution are CO32-, HCO3-, SO42- and MoO42-. The total dissolved solutes (TDS) are about 45 g/L. Various commercially available strong bases anionic resin-in-pulp (RIP) grade resins ? both macroporous and gel type, were studied with respect to their loading capacity. Parametric variation studies were then carried out with the short-listed resins. Results of the semi-continuous counter-current extraction and elution tests indicated extraction efficiency of about 98% and practically complete elution of the loaded uranium values with NaCl eluant using a gel type polystyrene based resin grafted with quaternary ammonium ion. Keywords: uranium, hydrometallurgy, ion exchange, resin-in-pulp

Sep 1, 2012

By R. R. Kallu

The current 120 psi seal design and evaluation practices are mostly based on simple analytical solutions. Considering the simplistic assumptions and limitations involved in simple analytical solutions and practical difficulties involved in conducting conventional full-scale explosion tests for evaluating 120 psi seal designs, there is a need for developing new scientific methods and engineering practices for design, analysis and evaluation of mine seals.

Jan 1, 2010

By Valerio Violo, Antonio Raschilla, George Kafantaris

"The Cityringen project in Copenhagen, Denmark will form a new circular line in the city center and will consist of 21 new stations (17 + four transfer stations) and approximately 31 km (19 miles) of earth pressure balance (EPB) twin-bored tunnels.The new tunnels passed under the historical building of Magasin du Nord, McDonald’s and two pubs in the heart of the city with a minimum cover of about 4 m (13 ft).To minimize the movements, a complex system of compensation grouting and jet grouting soil treatment was performed. A detailed action plan between the parties involved allowed coping with the critical tunnel boring machine’s (TBM) successful passage.The Cityringen is an extension of the existing metro line underground Copenhagen and will include the City Circle Line, 15 km (9.5 miles) of twin tunnels looping around the city. The City Circle Line will form a new circular track inside the city center and will intersect the existing M1 and M2 lines at Kongens Nytorv and Frederiksberg stations, as well as suburban train services at København H, Østerport and Nørrebro. It will extend the Metro network to the Nørrebro, Østerbro areas and the central station at København H (Fig.1). The two new lines M3 and M4 will run on the same tracks, but the M3 will be a circle route running around the entire line, whereas the M4 will drive from the station to the north side of the city.The €1.5 billion design-build contract was awarded by Metroselskabet in January 2011 to the Copenhagen Metro Team (CMT), a joint venture (JV) between the Italian companies Salini, Tecnimont Civil construction and Seli SpA. Since the bankruptcy of Seli SpA and Tecnimont, Salini Impregilo now owns 100 percent of the JV shares. Seli Tunneling Denmark ApS, a subcontractor to CMT, was initially constituted as a Seli SpA subsidiary and, following the economic difficulties of Seli SpA, was acquired in 2015 by Salini Impregilo. Seli Denmark is in charge of the tunnels excavation and lining and owns the four 5.84-m (19-ft) diameter Seli/Kawasaki earth pressure balance machines."

Jan 5, 2017

By S. C. Tadolini, P. Mills

"INTRODUCTION This research produced a shotcrete formulation that extends beyond stabilization and can be used to restore the structural integrity of damaged infrastructure. The primary challenge was to develop a shotcrete or gunite with structural strength within a few minutes to prevent parasitic loading and allow ingress into damaged structures within a few minutes of the mix formulation being applied. This also applies to mining conditions where rapid support of progressive failures can minimize failure. An additional benefit was the discovery that the product had extremely high adhesion properties in addition to high flexural strengths. The approach to product design was the development of “single bag” dry mixes that are entirely self-contained, can be rapidly transported anywhere in the field or underground, and be deployed using simple equipment. Dry mix eliminates issues relevant to high shear water mixing, as water is added in the form of a mist at the point of delivery; thus low W/C can be achieved. However, as there is no onsite powder mixing, the product must have a high degree of inherent homogeneity. A commercial version of this material is currently offered as Minova’s Tekcrete Fast® product which has been successfully deployed in the mining industry and is currently being used in civil, construction and tunneling operations. The material can rapidly stabilize unstable ground in metal/nonmetal and coal mines. This paper described the technology development, product testing results and applications in mining and civil applications. BACKGROUND The original development of this product was to complete rapid stabilization of shock damaged structures, which falls outside the purview of normal construction and mining practices, due to the critical time issue and the nature of the damaged structure. The stabilization of damaged structures requires materials and equipment that can be rapidly deployed to place materials that have very rapid strength development. These materials need to be placeable at a distance to provide some degree of safety to the responders. In addition, the materials must be able to adhere to structural surfaces that have not been specially prepared and conditioned, and may also be highly fractured, dusty, wet, and quite possibly hot or extremely cold. The technology for the rapid delivery of large volumes of cementitious materials to vertical or even overhead surfaces currently exists. Pneumatic delivery (shotcreting) has been used in construction for over 100 years (American Shotcrete Association, 2014). Shotcreting has played a major role in structures like the Washington D.C. Metro subway system and been used in underground mining applications routinely to serve as part of the primary and secondary support system when used in conjunction with traditional roof bolts. Numerous rapid setting cements are commercially available. They are used for rapid repair of surfaces such as bridge decks, pavements, and commercial floors, as well as structural repairs of vertical and overhead surfaces. Few of these products are specifically marketed for use in shotcrete applications. The majority of rapid setting cements are based on, or at least contain, Portland cement as a principle component. Other components are added that help provide early strength, such as high alumina cement (HAC), organic polymers, chemical accelerators (which can also be added during concrete batching), and calcium sulfate hemihydrate (e.g. gypsum plaster) (Lea, 1971). Cementitious mortars prepared with some of these cements can achieve compressive strengths of 6.8 – 13.8 MPa (1,000-2,000 psi) within 1 hour. However, Portland cement mortar and concrete typically require many weeks of proper curing to reach significant levels of their ultimate strengths, even when used with set accelerators. Also, high early strengths require the use of large proportions of Portland cement in the concrete mix, which can lead to high heat evolutio"

Jan 1, 2017

By J. H. Parliament

"The 15,000-tpd Similkameen open-pit copper mine, 10 miles south of Princeton, B.C., started production during 1972. The two main ore zones are separated by the deep canyon of the Similkameen River, with the Ingerbelle or western deposit being mined first. The location, design and construction of the plant were complicated by the steep terrain and the situation of the orebodies. Mining, utilizing 10-cu.yd electric shovels and 100-ton electric-wheel trucks, is conventional. Closely integrated with the preproduction mining was the construction of a 4-mile section of main highway to bypass the Ingerbelle pit. This entailed a very large fill, placed with mine equipment. Ore is crushed to minus 9 inches, stockpiled and reclaimed for direct delivery to three 32-ft-diameter by 14• ft single-stage autogenous grinding mills, each driven by two 4000-hp motors. Because of the friable ore in the upper part of the mine, 4-inch balls are added, with higher than design throughput attained. Classification is by 91>-inch spiral classifiers and cyclones. The flotation section comprises three parallel lines of ten 400-cu.ft rougher- scavenger cells and a single line of 100-cu.ft cleaner and recleaner cells. Concentrate is transported in end dump, closed trucks to Vancouver for dockside storage prior to shipment to the smelter. Tailings are piped across the canyon on a suspension bridge and through a tunnel to an empoundment area. Water is reclaimed and returned to the concentrator, forming a closed system. Dams are raised with cycloned ands, with the downstream section compacted."

Jan 1, 1973

By Patrick J. Maessen, Bart H. M. Hendrix

"In the Netherlands, the Dutch Tunnel Standard has been developed for the execution of road tunnel projects. The Dutch Tunnel Standard is based on the Dutch Tunnel Law (WARVW) which sets the minimum safety standard for road tunnels in the Netherlands. Uniformity of tunnels and the uniform perception of a tunnel by its users leads to a higher safety level. Therefore, several items in the Dutch Tunnel Standard are specifically developed to ensure safety in emergency situations through the plane of human factors. Taking human factors into account is important in regular traffic situations, but in an emergency situation, this can be vital. In this paper, the development and contents of the Dutch Tunnel Standard are explained in the first part and in the second part, the systems related to human factors are described. DUTCH TUNNEL LAW AND THE NEED FOR THE DUTCH TUNNEL STANDARD In the 90’s of last century and the early 2000’s, several serious accidents occurred in tunnels in Europe. These accidents involved fire and led to many casualties. After these accidents, the European Union decided to change the regulations for tunnel safety, leading to the EU directive 2004/54/EG. The primary goal of this directive is, that casualties are minimized in case of a calamity in a tunnel (e.g. fire). In the Netherlands, the EU directive led to the development of the tunnel law and a tunnel regulation (in 2006) to prescribe the safety features required for a safe tunnel. The new Dutch tunnel law – cited in the Building Act – was meant to make tunnel design easier – but resulted at first in the opposite effect. Tunnel design in the Netherlands and design standards of Rijkswaterstaat Rijkswaterstaat – the executing organisation of the Dutch Ministry of Infrastructure and the Environment – is the owner of the tunnels in the Dutch national motorway network, thus owner of the majority of the road tunnels in the Netherlands. In the early years of tunnel building in the Dutch national highway network (approximately 1950 – 1970), Rijkswaterstaat was not only owner, but also designer of its own assets. Most Dutch tunnels are submersed tunnels, because these type of tunnels provide a cost-effective way to make river crossings. Another type of tunnel that is used, is a TBM tunnel. Because of the geological conditions in the Netherlands (merely clay/peat and sand), there are no NATM or drill-and-blast tunnels in the Netherlands. Since the last decades, land tunnels (covered roads) are becoming more common to provide for multiple use of surface space and to meet more modern environmental regulations as traffic increases near densely populated areas. Tunnel lengths in the Netherlands vary from 500 m to 1.5 km for river crossings up to 6 km for the Western Scheldt (bored) tunnel. The lengths of land tunnels vary from 500 m up to 3 km. With these increasing lengths, some safety topics and design topics arise, topics that were non-issues in the past, when tunnels were only used as river crossings."

Jan 1, 2016

By Salinger, Herbert

WITH the large amount of metallurgical re- search work now being done and the constant effort of the engineer to effect economies of operation, I think it is a safe prediction that the next few years will see a great change in the handling of mine products. The well-managed mine, with sufficient ore reserves to warrant the necessary plants, will increasingly call upon the metallurgist and chemist for the solution of its problems. Shipping sorted ore or concentrate to the nearest smelter will not be the course followed. From ore to metal, or at least to a product directly salable to the consumer, will be the practice followed. As a consequence, mine managers will be increasingly interested in metal trade problems. By metal trade I mean the buying, selling, shipping, handling, and all the practices, forms and customs that go to make up the trade.

Jan 1, 1928

By L. E. Collins

"In western Canada, many new wells contain a significant fraction of H2S. As well, many older wells become increasingly sour over their operating lifetime. For these reasons, there has been increased demand for linepipe and casing for sour service applications in recent years. This paper will review the metallurgical factors which must be considered in designing steels for such applications. IPSCO’s development of linepipe and casing, and experience in fabricating products to meet test standards specified for sour service applications will be summarized. IntroductionWestern Canada produces the majority of Canada’s domestic crude oil and natural gas. A complex system of pipelines has been built to gather the oil and gas from the fields for transport to refining and/or cleaning operations. The gas carried in these pipelines can be either sweet or sour (i.e. containing no H2S or containing H2S) depending on the nature of the field from which it came. Many new fields contain a significant fraction of H2S and many older fields become more sour as their time in production increases. This uncertainty regarding product condition influences the user’s choice of materials for both casing and pipeline applications.It is well known (Merrick, 1989) that hydrogen induced cracking (HIC) will occur in steel when three conditions exist simultaneously: (1) the presence of H2S gas, (2) moisture, and (3) a susceptible material. Steelmakers can only address the latter of these factors. Development of steels to meet test requirements of sour service has been a major focus of IPSCO’s development work for several years."

Jan 1, 1998

By K J. McDonald

All commercially available zircon sands contain radioactivity sourcing from the decay of trace amounts of contained uranium (U) and thorium (Th). The fine particle size zircons of the Horsham area in the Murray Basin region of Victoria, Australia, contain significantly more (about twice) Th+U than those commercial zircon sands. The marketability of these fine-grained zircon sands is likely to rely on the removal of these radioactive impurities. CSIRO Minerals have been working for some time to develop processes for the removal of the radioactive impurities from zircon. It is generally agreed that it is quite impossible to leach U and Th from zircon, however, the Heat and Leach (HL) process, described in detail in Aral and McDonald (1999), reduces the radionuclide levels significantly. The identified (HL) process aims to leach uranium and thorium selectively from a decomposed zircon. The novelty of the process is that a large part of the leached product can be reconstituted to a low radiation zircon by a subsequent heat treatment. The HL process uses a flux mixture of sodium carbonate and calcium borate to decompose the zircon at relatively low temperatures (900 to 1150¦C) and a weak acid (0.5M HNO3; 80¦C/0.5 h; pulp density ten per cent) to leach the radionuclides selectively. The process leaves the major components (ZrO2 and SiO2) behind with little loss. The HL process for example lowers the U+Th content of a Murray Basin zircon from 1000 ppm to 400 ppm U+Th. Among the radionuclides more U progeny is removed than the Th series radionuclides. This is very significant as the radioactivity of U series is 2.5 times more that from the Th series. Therefore the reduction in the radioactivity level of zircon is more than the reduction in Th+U indicated by XRF analysis. A schematic flow sheet of the HL process is shown in Figure 1. Although the HL process successfully lowers the radionuclide levels in zircon sands, the final product contains significant amounts of sodium (up to 14 per cent Na2O) and small amounts of CaO. By comparison, the sodium content of the commercial zircon sands is in general 2O. Zircon is used mainly as an opacifier in tile glazing where the addition of ten to 15 per cent zircon to a translucent base glaze gives the sanitary white colour to the tile surface. Opacification is the result of the refractoriness of zircon particles at the glaze firing temperatures that is generally around 1050¦C.

Jan 1, 2001

By David J. Howard, Christine Broadbridge, David C. Paine

"High pressure vapor/solid reactions offer an opportunity for novel synthesis and processing of thin film materials and structures for electronic, optical, and magnetic applications. In this paper we review the use of two high pressure techniques that operate from 25 to 1000 atm (2.5 to 100 MPa) to fabricate thin film oxide structures from Si1-xGex deposited on Si wafers. High pressure synthesis enables temperature-independent control of reaction rates in the oxidation of this multicomponent semiconductor system and hence offers the opportunity to form thennodynamically metastable Si1-xGex<h from the alloy. The thermodynamics of the Si-Ge-0 system are reviewed and a method is described that utilizes selective chemical reduction (via H2 gas) of Si1-xGcx<h to form Ge precipitates in an SiO2 matrix. IntroductionAlloys of Si1-xGex grown epitaxially on Si substrates by chemical vapor deposition (CYD) and molecular beam epitaxy (MBE) have been used to create high performance microelectronic devices1. These devices show improved performance over conventional Si technology because they exploit the Si/Si 1-xGex band-gap discontinuity and take advantage of higher hole mobilities in the Ge containing alloys. While a range of devices based on heteroepitaxial systems have been demonstrated, the Si1_xGex alloys are of particular interest because they are most closely compatable with standard Si device processing. One disadvantage of Si-based materials systems is that they are not typically useful emitters of light. This is important since the use of light (rather than electrons) for transmitting and processing signals into, out of, and within Si-based microelectronics would represent a major technological advance in microelectronics-based communication and computer technologies. Nevertheless, through the use of innovative processing techniques it may be possible to use the Si1_xGex/Si heteroepitaxial system in integrated microelectronic/light-wave technologies."

Jan 1, 1994