Search Documents

By Tuomas van der Meer, Jukka Tanninen, Annukka E. Mäkinen, Mika Martikainen, Laura M. Nevatalo

The mining industry consumes huge water volumes and the waste streams typically contain sulfate, which has caused problems to many operations around the world. Discharge of sulfate to fresh waters is being restricted as the sulfate load increases salinity and causes problems when sulfate is reduced to toxic H2S by natural bacteria. To reduce fresh water consumption, internal water recycling had become a necessity in metallurgical processes. However, the recycling causes accumulation of sulfate and other components in water, causing problems to process performance and increases scaling in piping and equipment. Few technically feasible water treatment processes exist in the market that can be applied to decrease sulfate concentration below gypsum saturation level: biological sulfate reduction, membrane separation, ion exchange, evaporation and chemical precipitation. Some of these technologies are effective for treating wastewater, but there is typically a highly concentrated sulfate fraction left requiring still further treatment. Outotec has developed a sulfate removal solution, Outotec Ettringite process, which allows flexible control of residual sulfate concentration, thereby opening doors for increased water recycle within processes and control of the sulfate in discharged waters. In this article the results and benefits of this novel process along with examples of operating costs are presented.

Jan 1, 2014

By E. Lee Cameron

Summary Records of the past show that the first mineral production in what is now the Province of Manitoba consisted of salt, obtained about the year 1800 by the evaporation of brine. Also at an early time in our history, the Ordovician limestone at St. Andrews Locks, East Selkirk, and other localities was quarried for use as building scone in the construction of forts and fur trading posts. Both salt and building stone are still produced in Manitoba, although not from the original sources. In addition, there is now a substantial production of a variety of other industrial minerals and their products such as lime, crushed stone, gypsum, peat moss, and bentonite. The annual dollar value of production of the industrial mineral industry in Manitoba is today greater than at any time in our past and is derived from a greater variety of products. At the present time, exclusive of the various gravel pits operated by the Provincial Department of Public Works, twenty companies operating thirty-four separate pits, quarries, or mines are producing industrial mineral raw materials in Manitoba. This paper attempts to outline the development of the industry from its start about 1800 to the present, giving general information on the various materials produced. Some suggestions regarding the possibilities of establishing new industries based on other raw materials are given at the end of the paper.

Jan 1, 1949

By Christopher M. Moore

DK Recycling und Rohelsen GmbH converts 380 000 annual tonnes of iron containing waste materials Into pig Iron. Zinc Is the main reason that these materials are classified as waste. The materials are processed In the conventional way by making sinter which is then smelted in a blast furnace to foundry grade pig iron. The trick lies not in the unit operations which are quite standard but rather In the modifications made to the plant and operating procedures to cope with the much higher levels of tramp elements.

Jan 1, 1995

By William M. Thornton

[Owing to the comparatively high freezing point of nitroglycerin (14, 15, 16, 17, 18, 23, 37, 38)3/ - 1.9° C. and 13.0° C. for the labile and stabile modifications, respectively, as determined by Hibbert (16) - manufacturers of dynamites have incorporated into the liquid portion of these composite explosives various substances capable of participating in an explosion, to depress the above-mentioned freezing point. Aromatic nitro-compounds, chiefly nitrobenzenes, nitrotoluenes, and nitronaphthalenes, have been used to a considerable extent (11), but such nitrosubstitution products have not proved altogether satisfactory, as has been shown clearly by Naoúm. (14). Consequently there has been a strong tendency in recent years to replace them with one or more of several nitric esters, among which the following (29, 35) have been prominent: Dinitrochlorhydrin (monochlorhydrin dinitrate); nitrosugars, for example, sucrose octanitrate (19); tetranitrodiglycerin (diglycerin tetranitrate); nitroglycol (ethyleneglycol dinitrate); and diethyleneglycol dinitrate (13, 46, 47). Of these, nitroglycol (33, 4l, 45, 48, 49, 65) is outstanding in importance. As the Bureau of fines is naturally interested in the analytical chemistry of the "explosive oils," it seemed desirable to bring together in this report the widely scattered experimental work covering the problem of differentiation that has appeared in various chemical and physicochemical publications.]

Jan 1, 1941

By Robert W. Burns

Gentlemen, my subject today is glass reinforced plastics. By definition, this encompasses a wide variety of materials: at least a half dozen basic varieties of polyester, epoxy, and phenolic; virtually infinite compounding variations within the basic groups: literally limitless variations in the amount and the nature of the glass reinforcing. Complicating all of this is the fact that different modes of application of the same material fall appreciably alter' the product's general strength and suitability. These many, many differing materials are what we conveniently call "glass reinforced plastics" or, more simply, fiberglass". This common name is actually a large part of the problem when dealing with fiberglass materials. Far too often a specification is written calling for simply "fiberglass reinforced polyester', based on successful prior use of a polyester laminate. Such a specification is very nearly worthless since such tremendous variation is possible under it. Success of a laminate furnished under such a specification is entirely dependent on good fortune

Jan 1, 1962

By W. Ellison

Worldwide development of commercial markets for FGD (flue gas desulfurization) gypsum is described and used as a basis for assessing potential overall market growth and regional demand foreseen in the U.S. during the 1990s. Diverse strategies are outlined for cost-effective substitution of this major supply from acid rain control retrofits (power plant scrubbers) for natural gypsum in the principal, existing markets: gypsum board and portland cement. Another focus of utilization forecasting is a key group of related. new-product advancements including floor screeds, mining mortars and various types of innovative construction products.

Jan 1, 1993

By Oliver C. Ralston

Nonmetallic technologic investigations of the U. S. Bureau of Mines are headquartered at experiment stations in three widely separated localities of the United States. During 1936, the Nonmetals Division of the Technologic Branch was formally set up by combining the direction off the work of these three experiment stations under one administration. The New Brunswick (N.J.) station which in the past has been known as the Nonmetallic Minerals Experiment Station, is henceforth to be at College Park, Md., as part of the Eastern Experiment Station, and its principal activities will be related to the nonmetallic resources of the Eastern and New England States.

Jan 1, 1937

By P. Maraboutis

Iron removal by precipitation as jarosite from Fe-Ni-Co sulfate solutions, (synthetic or real, resulting from laterites leaching) has been investigated. Precipitation was carried out at 95 C, and at an initial pH 1.6, which was either kept constant with CaCO3 or Li2CO3 additions, or left to drift with the evolution of the reaction to lower values. The precipitation of K-, NH4- and Na- jarosite was initially examined using synthetic solutions. In all cases, hydronium ions were incorporated into the precipitate as well. Residual iron in solution was lower (0.2-1 g/1) and equilibrium was achieved faster (within 4-8 h) when precipitating K¬jarosite at constant pH, using CaCO3 for neutralization. Nickel and cobalt losses were small. Na- jarosite precipitation was also studied from real solutions with high initial iron content, under constant pH=1.5, controlled with CaCO3 additions, and it was shown that low residual iron concentration in solution (0.3-0.5 g/1) can be achieved again, with relatively small nickel and cobalt losses. The thickening and filtration characteristics of the precipitates were excellent in all cases examined.

Jan 1, 1988

By W. A. Lang

Introduction Under our present civilization, industrial developments will be greatest in those areas in which energy .can be most economically produced and efficiently used, where labour is in adequate supply, and where markets for the products of industry are available. A knowledge of fuels- the present major sources of energy- and of their utilization is therefore of vital importance. With that in mind, the aim in this paper will be to outline the known reserves of fuels in Alberta, to give their characteristics, to indicate the markets served by each, and to offer some suggestions for the future development of the coal industry. The paper should be regarded as a compilation of published data rather than as an original treatise. Alberta is richly blessed by having large reserves of mineral fuels. The estimated reserves of coal are 46,562 million tons. Alberta is the oil and gas province of Canada. The world's largest deposit of bituminous sand occurs along the Athabaska river in Alberta. In addition, there are large areas of forested land in the northern and western sections of the Province, and the rivers serve for the development of hydro-power.

Jan 1, 1949

By Maria I. De Rosa

The U.S. Bureau of Mines performed experiments to determine the embedded hydrogen chloride (HCI) and smoke particle characteristics during combustion of polyvinyl chloride (PVC) and chlorinated mine materials for development of a test parameter. The experiments were conducted in an approximately 20-L furnace at set furnace temperatures of 250° and 1,000° C, for a 14-min duration, with an airflow through the furnace of 10 L/min. The variables studied, as a function of time, were hydrogen chloride embedded on smoke particles, hydrogen chloride concentrations in the gas phase, smoke particle average diameter (dg) and particle concentration (no), and product of smoke particle diameter and concentration (dgno). Other variables included carbon monoxide (CO), carbon dioxide (CO2), and oxygen (O2) concentrations; sample mass weight loss; and furnace temperatures. Results show that there is a correlation between embedded hydrogen chloride, hydrogen chloride gas concentrations, and inverse of the smoke particle diameter-concentration product (1/dgno); the higher the hydrogen chloride gas concentrations, the higher the embedded hydrogen chloride, the higher the 1/(dgno) values. These correlations will enable development of a simple test parameter to assess the toxic hazard that these materials pose during fire.

Jan 1, 2010

By R C, K L. Rees, J S. J van Deventer

In contrast with previously published models for the carbon-in-pulp (CIP) process, the model proposed in this paper incorporates film transfer, intraparticle diffusion, simultaneous leaching, preg-robbing, the loading of multicomponent species, and the effects of fouling and changing cyanide levels. The rationale behind this comprehensive model is that changes in fouling and competitive adsorption along a CIP cascade affect the profiles of gold loading. As it is impossible to quantify all these non-ideal factors, a method is proposed whereby an imaginary species is postulated so as to combine all the competitive effects. A plant survey at the Telfer mine has shown that the mass loss due to a gravimetric analysis of the fouled carbon could be used directly to quantify this competitive effect. The degradation and consumption of cyanide along the Telfer CIP cascade enhance the loading of copper on to the carbon, which should be taken into account when modelling the gold profiles. It appeared that the effect of cyanide itself on the loading of gold was negligible compared with its effect on the copper. Evidently much more research is required on this topic in order to optimise CIP operations exposed to constantly changing conditions.

Jan 1, 1998

By A. Ignatieff

Introduction Some interest is being shown in Canada in underground gasification of coal and, as developments have now taken place in several countries of the world, it is thought that a review of progress, particularly from the viewpoint of a mining engineer, may be of interest. The literature on the subject, and notably that of Russian origin, is already very voluminous. The various methods of underground gasification of coal have evolved from initial attempts to employ underground workings as gasifiers of previously fragmented coal or to use some method that involves little or no preparatory work underground. The 'stream' method, shown schematically in Figure 1, has been the only one used in tests to date in countries outside the U.S.S.R. Other methods, involving preparatory work underground prior to gasification, are the early 'chamber' method, where fragmented coal was gasified in rooms between inlet and outlet entries, and the underground borehole' method, illustrated in Figure 2, where gasification is developed in a succession of boreholes which are temporarily sealed and then abandoned in turn after gasification. The stream method appears. to be particularly suitable for pitching seems as it is claimed that the pitch prevents ash accumulation or serious blockage from roof falls, and it also aids the circulation of the stream. As a considerable proportion of Canadian medium and high-rank coal seams are inclined, it would seem that, at least at the outset, the stream method or a modification thereof would be the one most applicable to all but the Saskatchewan lignite fields and the flat domestic-coal fields of Alberta.

Jan 1, 1949

By Parry. V. F., John B. Goodman

"INTRODUCTION The Denver region coal field, covering an area of approximately 7,640 square miles, extends from the Wyoming State line to the middle of El Paso County, Colo. The coal in this region is subbituminous in rank. Much of it is used as domestic fuel. During the last decade the production of coal in this field has remained fairly constant at an average of 2,600,000 tons per year. This production has come from 50 to 60 mines, 88 to 90 percent of the production being from the section of the field north of Denver.According to the Standard Specifications for Classification of Coal by Bank of the American Society for Testing Materials 4/ the coals in this region are classified in the Subbituminous B and C group. On the as—mined basis, they contain about 22 percent moisture and average 9,600 B.t.u. per pound. They are noncoking and slack to a variable extent when exposed to the weather. This is characteristic of subbituminous coals."

Aug 1, 1939

By Kenneth J. Miller

A novel two-stage froth flotation process to remove pyritic sulfur from fine- size coal is described. The process consists of a first-stage, standard coal flotation step in which high-ash refuse and some of the pyrite are removed as tailings. The first-stage clean coal froth concentrate is then repulped in fresh water, and a coal depressant, a pyrite collector, and a frother are added to float the remaining pyritic material. Laboratory and pilot plant flotation results with coals from the Lower Freeport and Pittsburgh beds are given. The pilot plant test results show that up to 80 percent pyritic sulfur reduction was achieved with the Lower Freeport bed coal and up to 50 percent with the Pittsburgh bed coal. Laboratory and pilot plant results were in excellent agreement, indicating that the process is a viable means of removing much of the sulfur from some coals.

Jan 1, 1974

Conventional wisdom in the mineral processing industry leads one to believe that pressure oxidation of refractory carbonaceous (preg-robbing) ores is not a practical approach to process development. Initial acid pressure oxidation testing on carbonaceous sulfide ores at the Twin Creeks Mine supported this conventional wisdom. After testing other refractory process options, including air and oxygen enriched roasting, Santa Fe Pacific Gold decided to take a second look at pressure oxidation, using conditions outside the normal range of conventional practice. A combination of very fine grinding and high operating temperature and pressure resulted in significant increases in gold extraction. This paper details the effect of operating parameters developed for Twin Creeks on gold recovery, sulfur oxidation, carbon oxidation/passivation and preg-robb through the laboratory and pilot plant investigations.

Jan 1, 1995

By G. Danha, D. Glasser, D. Hildebrandt, N. Hlabangana

"In this work, we apply a method known as the attainable region (AR) technique in order to optimize the milling and leaching process of a low grade gold ore. No work on the application of the AR optimization technique has been done yet on a joint milling and leaching process. The advantage of the AR approach lies in its ability to simplify the optimization problem, as searching over a defined set for the maximum of an objective function is a fairly standard procedure. The objective function we selected was that of optimizing a linear function of the value of the recovered material minus the cost of both milling and leaching. Using the three variables (milling time, leaching time and recovery), we constructed a 3D plot and used it to obtain all the possible recoveries from the different milling and leaching times. The optimum for our chosen objective was then found by overlaying a contour plot of the objective function on the 3D plot. Our results show that the optimum was obtained at 90 % recovery with a profit value of 600, milling time of 30 minutes and leaching time of 1750 minutes.INTRODUCTIONAfrican countries are facing a general increase in demand for electrical power. In South Africa, the demand is now surpassing the supply from ESKOM, the main electric power provider of the country. This has resulted in load shedding strategies being implemented in many local communities in an attempt by ESKOM to cope with the high demand. A potentially better approach is to propose use of energy efficient technologies in the country’s largest power consuming industry; the mineral processing sector.In mineral processing, milling is the highest consumer of energy. The objective of carrying out milling is not merely to reduce the particle size of the feed material, but also to liberate the constituent minerals that make up an ore. This is done so that valuable minerals can be separated from the gangue, in downstream processes, such as leaching. However, the milling process is generally performed relatively poorly, and at a considerable expense in terms of electrical power utilization. Tomanec and Milovanovic (1994) estimated that milling accounts for more than 50 % of the total power used in the concentration process, but this can rise to as high as 70 % for hard or finely dispersed and inter-grown ores. Apart from being relatively wasteful of energy, the milling process is also inefficient with regard to mineral liberation because of the indiscriminate nature of the grinding force."

Jan 1, 2016

By L. M. Pidgeon

Abstract The production of metallic calcium, by reduction of lime with aluminium, was investigated. Using a modified form of the effusion method, the vapour pressure of calcium above the reaction: 4CaO + 2Al ~ 3Ca + CaO.AI203 was determined and found to vary from 1.0 to 1.3 mm. Hg from 1,150° to l,200°C. From the magnitudes of the various thermodynamic quantities involved, together with a consideration of the known chemical characteristics of the reaction, it was suggested that the reaction proceeded by reduction of lime with aluminium vapour. INTRODUCTION The conventional production of metals by reduction of their ores by carbon (or carbon monoxide) may be represented by the equilibrium: MO+ R [] RO+ M . . . . . . . . . .(1) where MO represents the metal oxide, and R the reducing agent (carbon or carbon monoxide). The free energy change ?F° associated with the reaction is given by -?F° = RTlnKp . . . . . . . . ... . (2) where R is the gas constant, T the absolute temperature, and KP the equilibrium constant. It should be noted that ?F° represents ? the standard free energy gained by the system and hence -?F° is the free energy gained by the surroundings - and that as ?F° increases K must decrease, and conversely. For metals above manganese in the electromotive series, the ?F° associated with reaction would quantity and from it can be seen that this corresponds to a small fraction for K. The equilibrium pressure of the oxide of carbon represented by RO is then too near its concentration in the furnace gases for the reaction to proceed in an internally fired furnace. For the practical reduction of such metals, fuel fired furnaces are inadequate. Electric furnaces may be used to give higher temperatures with lower concentration of carbon oxides and the reaction may still proceed. However, for many metals such as calcium and aluminium the formation of stable carbides or acetylides may prevent production of the metal by this reaction. In this case, either electrolytic methods must be used, orrecourse must be had to reducing agents other than carbon. It is the latter method which is under consideration here.

Jan 1, 1948

By D. H. Carlson

The U.S. Bureau of Mines and Michigan Technological University (MTU) are collaborating to develop an apparatus for measuring diesel tailpipe emissions in underground mines. A tailpipe emissions measurement apparatus (EMA) is described that dilutes diesel exhaust and measures the concentrations of diesel particulate matter (DPM), CO, CO2, NO, and NO2 at known dilution ratios. The EMA was evaluated by side-by-side comparison of its measurements with those by laboratory-grade instruments. Concentrations of CO and CO2 measured by the EMA were usually within ± 14 pct of concentrations measured by laboratory-grade instruments for CO and ±20 pct for CO2. EMA¬ measured DPM concentrations were, on average, 29 pct lower than those measured by laboratory-grade instruments, with the differences being fairly consistent. The CO and CO2 differences are related to the method of calculating the EMA's dilution ratio, and the difference in DPM concentrations is attributed to thermophoretic and/or condensation losses related to the EMA's unheated sample probe. Preliminary analysis of data obtained with a heated sampling probe and modifications in the sampling procedures have indicated reduced variability in DPM and in the calculated dilution ratios.

Jan 1, 2010

By Lightfoot. Nicholas, Na Liu

"Mining in multi-seam workings has been undertaken for many years in the VK Remnant pillars above and/or below current working areas have an important influence on retreat gateroad conditions at five of the remaining six deep coal mines. These interaction effects need lo be predicted ahead of mining so that longwall panels can be positioned to minimize roadway damage and to identify areas where additional support should be installed early into competent strata when and where it is most effective.Currently, three-dimensional elastic stress analysis using MAP3D is undertaken to predict local vertical and horizontal stress magnitudes during gateroad development and in front of the face on retreat. The predicted stress fields are often used as input to FLAC for roadway modelling.Using Maltby Colliery in South Yorkshire as a case study, this paper illustrates the MAP3D approach, together with its current limitations and uncertainties. Possible future improvements in the analysis method are proposed and the authors would welcome comments on these, or suggestions for alternative approaches.MODELLING OF MULTl-SEAM LAYOUT & MULTI-SEAM INTERACTIONThe remaining large coal mines in the UK arc operating at depths of 800-1, 150 m (2,625-3,773 ft). Production panels are now mined on retreat after the accompanying single entry access roadways have been completed. These gateroads are typically supported with a system of steel rock bolts and cable in the roof and steel bolts and glass re in forced polymer (G RP) dowels in the sidewalls.In addition to new panels being mined in the vicinity of old goafed districts, a significant amount of extraction has usually already taken place in coal seams above and/or below the current working areas. This means that there is also interaction between the current workings and the remnants of the old workings in other seams. As a consequence of the mining methods employed, old workings can have a complex geometry compri ing collapsed and partially collapsed excavations intersper ed with small and large pillars of unmined coal. The unmined coal pillar act as stress concentrators that carry the overburden load while the mined out excavations create stress shadows of varying degrees depending on how much collap e and reconsolidat ion has occurred. This is illustrated by a simple elastic model as shown in Figure I."

Jan 1, 2010

By A. K. Martin

Adaptive management can be described as a structured, iterative process of robust decision making in the face of uncertainty, with a goal of reducing uncertainty over time through system monitoring. Adaptive management is a tool which can be applied to not only change a system, but learn about the system (Holling, 1978). Adaptive management has been used in ecosystem management for years and guidance is provided in a variety of handbooks and publications. Adaptive management can be applied to industrial facilities and mines through the use of an adaptive environmental management plan (AEMP) and associated practices. The goal of this paper is to provide an explanation of how the plans and practices support regulatory agency approvals and permitting, span the life-cycle of mines, manage uncertainty, and assist in addressing mining impact and legacy issues. AEMPs and associated practices are useful tools to address the uncertainties in identifying, evaluating, and managing impacts of proposed new and modified mining facilities undergoing environmental review. Once a proposed project is approved, the AEMP continues as a living document, being informed, revised, and adapted by the operations. The AEMP can serve as an ongoing management tool for describing and evaluating environmental impacts, continuing in operations into post reclamation. If initiated during planning and environmental review of a project (and in some locations such as the United States [U.S.], the preparation of an Environmental Impact Statement (EIS)), the AEMP becomes a basis to identify, monitor, and manage potential project environmental impacts. Development of an AEMP for an operating mine is also beneficial since there are generally developing and ongoing environmental issues at those facilities as well. Over time, the AEMP is adapted to changing requirements and conditions including those anticipated and unanticipated. Ever increasing scrutiny of mining projects and the complexities of the EIS process highlight the uncertainties inherent in impact predictions. In making the momentous decision of initial project approval, these uncertainties can discourage the regulatory agencies? actions and create stakeholder anxiety and controversy about a project. A well-designed AEMP can support the decision to approve an EIS and enable a project to move forward. Additionally, an AEMP can inform financial assurance estimates and revisions over the life of a mine providing all parties including the citizens of the surrounding communities with greater confidence that potential environmental impacts and risks will be well managed.

Feb 23, 2014