Search Documents

Determining the environmental consequences of green field projects is becoming an increasingly important component of new projects. Feasibility studies are regarded by potential investors as incomplete if a comprehensive Environmental Impact Assessment (EIA) has not been completed. These EIAÆs need to meet various local and international requirements in order to achieve bankability. Heavy mineral mining projects are often located in ecological sensitive coastal zones, and bring with them a suite of social impacts in the mainly developing countries within which they are usually located. This paper draws on experience gained in undertaking EIAÆs for heavy mineral mining projects in Kenya, Mozambique and South Africa, and uses these case studies to identify potential pitfalls. Important lessons include the need to initiate the EIA process as early as possible in the project, in order to develop management systems to mitigate the environmental impacts of exploration. Close and on-going consultation with affected communities is also seen to be critical to the success of the EIA. Proactive participation on the part of the environmental consultants with the project team and all interested and affected parties (IAPs) is important. An EIA commissioned later in project planning makes it difficult for the EIA to contribute in a positive manner to the project. Early engagement with environmental consultants allows the environmental assessment to develop from a report to an actual process, and to become fully integrated with project planning. The proviso is that an initial æfatal flawÆ assessment is required to identify any potential æshow stoppersÆ, in order to meet one of the important objectives of EIA, namely an assessment of whether or not the proposed project is the preferred development intervention in the study area. For more controversial proposals this may require the commissioning of a Strategic Environmental Assessment (SEA), which circumvents some of the limitations of the project level EIA. Whilst confidentiality is a constraint to full disclosure, an open participatory approach to public consultation is essential to add credibility to the EIA process and to gain, at least, the acceptance of the process from the majority of IAPs. Full disclosure is encouraged by organisations such as the International Finance Corporation, who acknowledge that good public consultation costs a lot of money, but bad public consultation costs a lot more! An open approach to disclosure presents understandable difficulties for proponents, as they are required to give up some of their control over the project, and to trust the social scientists engaged in the process. However, independence in the EIA process is critical to its success. This paper will highlight these and other issues by drawing on five case studies to identify lessons learnt, and explore the above themes in more detail.

Jan 1, 2001

By G. D. Markland

The Moose Mountain mine is located in a belt of Precambrian volcanic rocks situated 20 miles north of Sudbury, Ontario. It was the first iron mining operation in the Archean iron-formations of the Canadian Shield. The ore is believed to have been formed in an environment of active volcanism, being part of a pyroclastic and volcanic series where only the iron-formation and chert qualify as chemical sediments. The volcanic environment, subsequent regional tectonics and metamorphism produced orebodies which differ from the main sedimentary iron ranges of the world in such features as continuity, grade, structure and metallurgical characteristics. The orebodies occur as relatively small lenses which have been complexly folded, faulted and intruded by acidic and basic dykes.

Feb 1, 1966

By P B. Hills, R J. Walton

Geotechnical instrumentation has been implemented as a key step for monitoring and optimising an engineered mine design for managing seismicity at the Beaconsfield Gold Mine. Measurements of displacement, stress change, ground control element load and seismic response of the rock mass allow for back analysis and calibration of critical parameters for feedback into the engineering design loop. Instrument clusters are installed in strategic locations prior to the commencement of stoping in order to determine the nature of the response of the rock mass to stoping. A selection of instruments including instrumented cable bolts and rod extensometers, resistance wire extensometers, hollow inclusion stress cells, vibrating wire stress meters and resistance wire extensometers are used to gather data through a data logging system. The rate at which data is recorded is adjusted to provide more information during periods of anticipated rapid change such as around stope firings or during periods of high seismic activity, and less information during periods of anticipated quiescence. The twofold purpose of the instrumentation is to calibrate the numerical modelling output which forms the basis of the engineered mine design, and to provide an alert mechanism where the behaviour of the rock mass is not what was anticipated, or where the impact of that behaviour may compromise the integrity of the engineered ground control system. The paper describes the location of instrument clusters with respect to stoping, the type of instruments employed and the method of data acquisition. It provides examples of results obtained and illustrates the way in which that information is used to optimise the mine design and manage seismicity.

Jan 1, 2008

By M. S. Badollet

INTRODUCTION THE DEMAND for general knowledge on asbestos fibres has increased considerably in recent years. A few publications have printed data showing some of the physical and chemical prupertie3 of asbestos, but in many cases this information is difficult to find and is seldom available when needed. During the past ten years, Johns-Manville have received many inquiries on the physical and chemical properties of asbestos fibres. Fortunately, we had some of the information in our files, and we willingly supplied the data. To help relieve this need, we have tried to present briefly in this paper some of the interesting and out-standing properties of asbestos. This information was obtained over a period of years by search of the literature and by experimental investigations. PROPERTIES OF ASBESTOS FIBRES Table I (1, 2) presents, in convenient form for easy comparison, data on the principal properties of the several varieties of commercial 'asbestos' -actinolite, amosite, anthophyllite, chrysotile, crocidolite, and tremolite. Under each variety of fibre is a brief statement describing the properties in terms of structure, mineral association, origin, etc. Some of the more important data in Table I are expanded and presented in Table II (3). SOLUBILITY OF ASBESTOS A report ( 4, 5) discussing the effects of acids and caustic on asbestos fibres was published in Germany in 1927.

Jan 1, 1951

By Alonso Marchena, William Martínez

El estudio que se ve reflejado en el presente artículo tuvo como objetivo mantener actualizado el mapa metalogenético del Perú y desarrollar conceptos sobre el origen de los yacimientos minerales, basados en datos geocronométricos, geoquímicos, isotópicos, estratigráficos y estructurales, en la Cordillera Occidental entre Ica y Tacna. La zona de investigación comprende las franjas metalogenéticas IV, V, VIII, IX y X. Se destaca el valor de herramientas tales como la litogeoquímica en la discriminación de pórfidos de Cu (Mo-Au) y se muestra la efectividad de nuevos parámetros de elementos traza en la discriminación y reconocimiento de magmatismo fértil vinculado a pórfidos en el sur del Perú.

Oct 30, 2020

By A. Dreimans

Tracing of 'float' against the latest ice-flow directions ha!' led to or assisted in discoveries of several mineral deposits in Canada at lP.ast since 1891, e.g., fluorite and corundum in eastern ?Ontario, Steeprock and Josephine iron ore in western Ontario, Malartic, Fisher-Quebec, and Lamaque gold ore, and Vendome zinc ore, in western Quebec, Sullivan zinc and lead sulphides in British Columbia, Orvan Brook or New Calumet sulphide deposit in New Brunswick, Lynn Lake nickel sulphide de-posit in Manitoba, etc. Pebbles or ore boulders whose source has not yet been found include diamonds in the Great Lakes region and ?sulphides in several localities in Ontario and Quebec. Complexity of transport of ore boulders, including non-glacial transport, may be the explanation. Tracing of ore boulders requires knowledge of the Pleistocene history of each particular area (ice flow directions, their ?changes during glacial oscillations, existence of pre-glacial lakes with ice-rafted boulders, later interference by streams, lakes, mass movements). Important also is distinction of till from similar non-glacial deposits and knowledge of the bed-rock geology. Quantitative methods, e.g., pebble counts, maybe applied while tracing magnetite, hematite, or goethite. Fragments of sulphide ores are less abundant in indicator trains, and quantitative methods are less suit-able for tracing them. Heavy-miner-al investigations may give good results for minerals resistant to weathering. Geochemical methods are of value only in the vicinity of ore deposits.

Jan 1, 1958

By P. Zhang, S. Al-Thyabat

"Phosphate rock contains traces of rare earth elements (REEs) and can be a secondary source of these critical materials as large tonnages of phosphate rock are mined annually. Attention has mostly focused on the extraction of REEs from phosphogypsum, which contains more than 70 percent of the REEs reporting to phosphate concentrate, with only limited work conducted on REE extraction from sand tailings and slime even though they account for 16 percent and 15 percent, respectively, of REEs mined with phosphate matrix.In this work, phosphate flotation tailings were upgraded by gravity separation and froth flotation. Gravity separation was conducted using a laboratory shaking table, while flotation was conducted in a Denver D-12 flotation cell. The concentrated tailings were then leached by nitric acid followed by REE extraction with solvent and ion-exchange resin.The sand tailings were assayed as having 2.6 percent phosphate (P2O5 ) and 198.1 µg/g REEs. It was found that the shaking table could produce tailing concentrate assayed as having 8.6 percent P2O5 and 616 µg/g REEs but with only 20 percent REE recovery, while the froth flotation produced froth concentrate assayed as having 8.1 percent P2O5 and 368.2 µg/g REEs with 63.5 percent REE recovery. Leaching the flotation concentrate with 5.2 M (25 percent) nitric acid followed by extraction with solvent and ion-exchange resin yielded precipitates with REE contents of 0.926 and 0.314 percent, respectively, compared with 0.716 and 0.213 percent when table concentrate was used.IntroductionRare earth elements (REEs) consist of a group of 17 elements: the 15 lanthanides along with yttrium (Y) and scandium (Sc). They are rare not because of their scarcity in the Earth’s crust but because they are rarely found in economic and mineable deposits. REEs are called “seeds of technology” because of their importance to some critical technological industries such as renewable energy, hybrid cars, electronics and batteries. On average, an electric car or a hybrid car contains about 10 kg of REEs (Grasso, 2012; Radhika et al., 2011).REEs are usually categorized into light (LREE) and heavy (HREE). LREEs consist of lanthanum (La), cerium (Ce), praseodymium (Pr), neodymium (Nd), promethium (Pr), samarium (Sm), europium (Eu), gadolinium (Gd) and scandium (Sc), while HREEs consist of terbium (Tb), dysprosium (Dy), holmium (Ho), erbium (Er), thulium (Tm), ytterbium (Yb), lutetium (Lu) and yttrium (Y). About 200 minerals contain traces of REEs, but only three are considered economically significant: bastnasite, with the formula La,Ce(CO3)F; monazite, with the formula(Ce,La,Nd,Th)PO4; and xenotime, with the formulaYPO4 (Jordens, Cheng and Waters, 2013)."

Jan 1, 2016

By R. W. Boyle

"The concept of using chemical methods in prospecting dates back at least to the middle of the 16th century. Modern methods of geochemical prospecting, however, based on secondary haloes and utilizing trace-element techniques, were first practised in the U.S.S.R. and the Scandinavian countries in the 1930's. After 1945, methods based on soils, stream sediments and vegetation were rapidly developed in the U.S.A., the United Kingdom, Canada, France and other countries.The modern methods of geochemical prospecting owe their rapid development in the 20th century to the following:1.-Recognition of the primary and secondary dispersion haloes and trains that are associated with all mineral deposits. 2.-Development of accurate and rapid analytical methods utilizing the spectrograph and the various specific sensitive colorimetrie reagents, especially dithizone. 3.-Development of polyethylene laboratory ware of all types and the development of resins. This permitted greater freedom of field analyses and reduced the incidence of contamination.4.-Development of gas chromatography. This permitted the rapid and accurate determination of hydrocarbons in petroleum prospecting.Future research in geochemical prospecting should be focused on the following tasks: 1.-Definition of geochemical provinces and their relation to mineral deposits. 2.-Development of methods for discovering large low-grade deposits. 3.-Development of methods for discovering deeply buried deposits. 4.-Further development of methods to outline primary haloes. 5.-Eiucidation and formulation of techniques to relate the size and intensity of anomalies to the grade of the deposits. 6.-Development and refinement of biogeochemical methods, especially those based on indicator plants, chlorotic or toxic effects, and microbiological techniques. 7.-Definition of the types of primary and secondary haloes associated with accumulations of oil and gas."

Jan 1, 1967

By Welby G. Courtney

The Bureau of Mines conducted an exploratory field survey to determine the amount of airborne coal dust, the size distribution of the dust, and the rate of dust deposition in coal mine airways. The survey was taken at eight underground locations in operating coal mines. The rate of dust deposition in the airways depended upon the concentration of air-borne dust and decreased exponentially with distance from the dust source. The rate was seemingly independent of the size of the airborne dust particles. The rate of deposition, along a return, for the coal dust from a fade being mined with a continuous mining machine closely matched the rate for the rock dust from a trickle duster. A sample rock-dusting schedule for that return is presented; that is, the trickle duster should be operated for 3-112 hours after every five shifts to protect the average deposit of new float coal dust in the return, but operation after every three shifts is preferred, to protect an occasional heavier deposit.

Jan 1, 1982

In many base metal sulphide concentrators reagents such as collector and cyanide are often added to the grinding mill as well as to the flotation circuit. Whilst good reasons can be cited for splitting the reagent addition in this way, the benefits of such are rarely quantified and the complex reagent-mineral-media interactions occurring during milling are often poorly understood in terms of pulp chemistry. A new laboratory batch grinding mill designed by Magotteaux allows the user to measure, monitor, and control the pulp chemical conditions during grinding when testing different ores and media. Some of these parameters include pulp pH, pulp Eh, temperature, gaseous atmosphere, and dissolved oxygen concentration. In a recent development, the mill has been coupled with a simple on-line reagent monitoring system, designed by CSIRO, which allows the levels of species such as xanthate and cyanide in the grinding pulp to also be measured continuously during milling using a robust UV detection system. In this way the uptake of collector during grinding and the rate and ex-tent of cyanide interaction with the minerals and media can be determined as a function of grinding time. A series of grinding tests using an Australian nickel sulphide ore was conducted with the coupled system in which the cyanide dose, xanthate dose, and media type were systematically varied. The xanthate and cyanide levels were monitored as a function of grinding time and the data collected are discussed in terms of the pulp chemistry of the system and implications for plant reagent dosing strategies.

Jan 1, 2014

By H. M. Stewart, N. F. Dawson, J. P. Beukes, P. G. van Zyl, Q. P. Campbell, A. Jordaan, R. I. Glastonbury, L. N. Sadiki

"SynopsisThe physical properties of oxidative sintered pellets produced from typical South African UG2 ore are compared with the physical properties of pellets produced with conventional South African metallurgical-grade chromite ore (from the Lower Group 6 or the Middle Group 1 and 2 seams). A statistical evaluation of the cured (sintered) compressive strengths proved that pellets prepared from UG2 ore are likely to have the same, or better, compressive strength than pellets prepared from metallurgical-grade chromite ore. The cured abrasion strength of the UG2 pellets was also superior to that of the metallurgical-grade pellets. Scanning electron microscopy (SEM) backscatter, secondary electron, and elemental X-ray mapping were used to determine the reasons for the general superior strength of the UG2 pellets. The case study UG2 ore also required 13 kWh/t less energy for milling to attain the required particle size distribution prior to pelletization, which can lead to substantial cost savings. Results presented in this paper can be utilized by ferrochromium (FeCr) producers to better quantify the advantages and disadvantages associated with the use of UG2 ore for FeCr production.IntroductionChromite, a mineral of the spinel group, is the only commercially viable source of virgin chromium units. Geologically, commercial chromite deposits in the world are found in three forms, i.e. alluvial-, podiform-, and stratiform-type deposits (Murthy et al., 2011; Cramer et al., 2004). Alluvial deposits were formed by weathering of chromite-bearing rock with the subsequent release of chromite and gravity concentration by flowing water. However, these deposits are relatively small and of comparatively minor commercial interest. Podiform-type chromite deposits usually occur as irregularly shaped pods or lenses, and their distribution within a mineralized zone is usually relatively erratic and unpredictable, making the exploration of these deposits difficult and costly (Cramer et al., 2004). Stratiform-type chromite deposits occur as parallel seams in large, layered igneous rock complexes with more regular layering and lateral continuity (Cramer et al., 2004). The largest example of a stratiformtype chromite deposit is the Bushveld Complex (BC) in South Africa, which holds an estimated three-quarters of the world’s viable chromite ore resources (Cramer et al., 2004).Several chromite seams exist in the BC. The seams of economic interest are the Lower Group 6 (LG6), the Middle Group 1 and 2 (MG1 and 2), and the Upper Group 2 (UG2) seams (Cramer et al., 2004). The LG and MG seams are specifically exploited for their chromium content, while the UG2 seam is mined primarily as a source of platinum group minerals (PGMs) (Xiao and Laplante 2004). Extraction of the PGMs from the UG2 ore usually involves the liberation of the sulphide by milling and subsequent recovery of the PGM concentrate through flotation (Xiao and Laplante, 2004). Chromite in the PGM concentrate is undesirable; therefore, PGM recovery circuits are specifically designed to ensure maximum rejection of the chromite to the tailings stream. However, the chromite in the PGM tailings can potentially serve as feedstock for ferrochrome (FeCr) production, after beneficiation to increase the chromium content."

Jan 1, 2015

By R. D. Van Zant

The method for smelting zinc in horizontal retorts developed several centuries ago is still in use. This process consists essentially of the reduction of zinc oxide by carbon at 1,200° to 1,400° C. in a fire-clay retort. The reaction is highly endothermic, and a high radiation loss occurs in transferring the heat of reaction through the fire-clay walls. In recent years, silicon carbide retorts with much better heat-transfer characteristics than fire clay have been supplanting the old retorts. The practical impossibility of recovering the carbon monoxide formed in the reduction causes a large loss of fuel. Intermittent smelting is done in small retorts that are manually charged and discharged, and the furnace crews must be specially trained if efficient results are to be obtained. During the past 20 years several processes have been introduced that have substantially improved the horizontal-retort process. One of these, developed by the New Jersey Zinc Co., consists of a continuous process in which a briquetted mixture of zinc sinter, reducing agent, and binder is coked at 750° to 900° C. and charged into a vertical silicon carbide retort. A supply of displacement air or exhaust combustion gas is introduced at the base of the retort at an appropriate pressure in order to keep the zinc vapor from condensing on the cooled residue in the lower part of the retort. Any .oxidizing constituents in the displacement gas are converted to carbon monoxide by reaction with the carbon in the charge. The spent residue is continuously removed at the bottom of tl1e retort. The chief advantages of this process are said to be increased output per man-day, improved working conditions, high recovery of zinc, increased thermal efficiency, and long retort life.

Jan 1, 1950

By D. E. Healy

In 1989 an Autogenous Grinding Task Force was formed to study potential autogenous grinding circuits to replace the existing semi-autogenous grinding at the National Steel Pellet Plant located in Keewatin, Minnesota. Pilot plant test work performed by the Hanna Research Center (HRC) indicated that fully autogenous grinding with pebble extraction and crushing could feasibly be incorporated into the existing circuits. In 1990, one of the existing ten grinding mills was converted for an in-plant test incorporating pebble crushing. The full scale test work conducted in 1990 and 1991 verified the pilot plant projections with primary mill throughputs from the fully autogenous circuit utilizing pebble crushing being greater than throughput of the existing SAG mill circuits.

Jan 1, 1992

By P. F. Sands

This U.S. Bureau of Mines report reviews the state of the art in blind pneumatic stowing of backfill in voids in abandoned coal mines. It contains a short history of the development of pneumatic equipment in mining and four recent case histories of blind pneumatic stowing. Limitations of pneumatic stowing in terms of equipment wear, costs, backfill material, and methodology are discussed, and some new procedures and designs are reviewed. A bibliography covering pneumatics in mining is included also. This report provides background for the preparation of a Bureau test program in which the variables affecting the efficiency of pneumatic backfilling will be studied using a full-scale surface test facility.

Jan 1, 1990

By J. J. Dowd

1. The Pittsburgh bed is the most important bed in Ohio County, and virtually the entire production of coal in the county comes from this bed. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 tons per acre-foot of-coal in place, are estimated at 365 million short tons as of January 1, 1954. Of this total, 356 million short tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By U. Erb, L. Monaco

"Electrodeposited nanomaterials are increasingly implemented in advanced industrial applications in the aerospace, automotive, defence, electronic and energy sectors due to their outstanding physical, chemical and mechanical properties, including increased strength and wear resistance, and superb magnetic properties. As with the development of any class of new materials, the corrosion behaviour of these electrodeposits requires considerable attention. This presentation reviews major developments in the understanding of the corrosion behaviour of nanocrystalline metals, alloys and metal-matrix composites over the last 20 years, with emphasis on how their intrinsically high density of intercrystalline defects does not compromise their corrosion resistance as initially expected.INTRODUCTIONOver the past 20 years there have been considerable advances in the understanding of the corrosion behaviour of nanocrystalline metals, alloys and metal-matrix composites. In this paper, the corrosion properties of nanocrystalline nickel, cobalt, zinc, and copper and some of their alloys are reviewed with emphasis on how a reduction in grain size affects their corrosion behaviour in different environments.It is possible to synthesize nanocrystalline material with microstructural refinement down to the range of 1 to 100 nm using a large number of processing methods. There are five basic synthesis methods that can be used to classify the different techniques: vapor-phase processing, liquid-phase processing, solid-phase processing, chemical synthesis, and electrochemical synthesis. Depending on the synthesis method, different microstructures (equiaxed, textured), shapes, and forms (films, particles, bulk material) may be produced. In addition, other factors may be introduced (eg. residual porosity or amorphous phases), aside from microstructural refinement, which can contribute to the observed properties (Erb, 2010). In order to interpret and categorize the resulting microstructures, a dimensional structure modulation scheme was introduced by Siegel (1996) in which zero-dimensional nanomaterials refer to individual particles, clusters, etc. One-dimensionality results from a layered (less than 100 nm thick) structure. Two-dimensional nanomaterials are thin, layered structures containing grains (less than 100 nm) within each layer. Finally, three-dimensional nanomaterials are bulk structures with an average grain size less than 100 nm."

Jan 1, 2012

By Ian Baker, Xavier Pierron

"Iron aluminides hold great promise for intermediate temperature applications (to ~ 600°C) because of their excellent oxidation and sulphidation resistance and good strength. However, they have poor low temperature ductility, a feature which is exacerbated by water-containing environments. This paper presents an overview of the effects of environment on the ductility of iron aluminides, including the effects of iron aluminum ratio; ternary alloying additions, particularly boron; strain rate; and temperature. The mechanisms involved in water-induced embrittlement are discussed.IntroductionOver the last few years, it has became increasingly evident that the ductility and fracture toughness of many intermetallic compounds, particularly aluminides, are reduced dramatically if they are mechanically tested in either air or in hydrogen-containing atmospheres (1-5). For FeAI and Fe3AI, it has been shown that water vapor, for example in air at room temperature, can form atomic hydrogen by reacting with the Al atoms (1, 2). As a result in iron aluminides, the environmental embrittlement process is quite similar to traditional hydrogen embrittlement. This can be easily demonstrated by either testing an iron aluminide in an environment free of the deleterious species or by testing at high strain rates, both of which result in greater ductility. The purpose of this paper is to review recent progress in understanding environmental embrittlement in FeAI and Fe3AI, and to consider possible environmental embrittlement mechanisms. Greater understanding of this phenomenon will lead ultimately to remedies to this problem which is a major reason for preventing the practical application of these materials. First, some background on the iron-rich aluminides."

Jan 1, 1996

By Nathanael Hudson, Ruel A. Overfelt, Sushil H. Bhavnani

"In the aerospace and automotive industries, complex shapes exist which require casting. The problem with these cast parts is the empiricism required to develop the casting process and the accompanying time and expense to develop that process.There has been an interest in using fluidized beds to allow molding sand to better encapsulate the complicated surface geometries of lost foam patterns. Fluidization coupled with a mixing jet helps to homogenize the sand through stirring and may improve the integrity of the casting.At issue is the hydrodynamics of the sand and air around the foam pattern. The commercial package PHOENlCSTM is used to simulate the flow around the pre-casting foam geometry. Employing a two fluid approach, each component is considered a fluid that interpenetrates the other phase. To this end, the kinetic theory of granular 'flow for the sand phase was incorporated into the re-compilable PHOENlCSTM code.The results of this study consist of time-averaged void fraction patterns, with voidage being defined as the fraction of air in the mixture, around the foam pattern submerged in a two-dimensional fluidized bed. The model was benchmarked against past fluidized bed experiments. In order to better understand the dependence of the void fraction pattern around the lost foam pattern, certain physical parameters are varied and the resultant void fraction maps are predicted with the model. Physical parameters such as the aspect ratio of length to width, the placement of the mixing jet, and different mixing jet velocities are varied to illustrate the dependence of the time-averaged void fraction on those variables.Results consistently indicate the presence of channeling around the lost foam pattern, with the extent of the channeling and void formation reliant to a greater degree upon the placement of the mixing jet, and to a lesser degree on mixing jet velocity and aspect ratio.The increase in radial position of the mixing jet from the bed centerline had the desirable effect of granting the churning benefits of a penetrating jet, while at the same time minimizing the formation of excess void fraction at the top of the pattern."

Jan 1, 2001

By John J. Barakso

A summary of geochemical dispersion processes is presented. Secondary and tertiary dispersion of uranium was examined at several uranium prospects in British Columbia. The vertical migration of uranium from bedrock (primary dispersion) through overburden into the various soil horizons, and into snow and plants, was studied, and relationships were sought to explain the dispersion patterns in the secondary and tertiary environments. Soil developments were examined to obtain information on factors affecting the dispersion of uranium in soil profiles and tertiary substances; samples were analyzed for a number of elements. Biogeochemical data indicate that plant geochemistry is a possible exploration aid in areas of heavy overburden owing to the high selectivity of certain plants for specific elements. Some new data on the geochemistry of snow are discussed as a matter of research interest in the tertiary dispersion of uranium. Analytical techniques and problems are discussed, particularly extraction techniques, which must be carefully chosen to give reliable information on uranium dispersion.

Jan 1, 1979

By J. V. Thompson

The Powderhorn complex as a source of perovskite (calcium titanate) containing about 1.5% rare earths has been examined in several recent feasibility studies. Much promising exploration and process research has been done in recent years. This paper is presented with cautious optimism and with the acknowledgment that there may be some technical and economic areas yet to be explored. The Powderhorn carbonatite and alkalic stock in Gunnison County, Colorado, lies about 203 airlines km southwest of Denver at an elevation of 2450 to 2750 m (see Figures land 2). All of the mineable ore bodies are owned by Buttes Resources Company of Houston, Texas.

Jan 1, 1990