Search Documents

By R. D. Leitch

[The accepted theory of acid formation in coal mines with the subsequent appearance of the acid in coal-mine drainage, is oxidation of iron pyrite and subsequent solution and hydrolysis of the iron sulphate formed. It has also been found that 5 gobbed sections and worked-out areas, where there is usually an abundance of iron pyrite-bearing, materials in contact with air, are the sections that make the most important contribution to the quantity of acid drainage. It would thus seem obvious that if oxygen can be kept out of contact with tae acid-forming materials in tie- sections mentioned the amount of acid in coal-mine drainage could be reduced markedly and corrosion problems with mine pumping equipment and general stream pollution mitigated thereby. Although the efficiency of the suggested remedy as been borne out by laboratory experiments6, it has appeared desirable to substantiate the laboratory work by field observations in so far as pertinent data are available. It has been difficult to learn of mines or sections of mines about to be sealed, whereby an actual comparison of the drainage before and after sealing can be made. In view of that difficulty it has been necessary to devote attention to a comparison of the character of the water from areas already sealed with that from open but otherwise comparable sections of the sane mine. Previous cork has shown that the acidity of drainage in different parts of the same mine may vary, but if it can be shown also that the water from sealed areas is with but fen exceptions less acid than the otherwise similar open sections of tae same mine, the laboratory finding will be supported in a practical gray. This report presents some of the evidence that has been obtained.]

Jan 1, 1930

Southeast Alaska's mining industry has come to life after nearly 50 years of relative dormancy. Commencement of operations of the Greens Creek Mine in 1989 marked a turning point in the industry as the first large scale mining operation in the region since closure of the Alaska-Juneau Mine in 1944. The Greens Creek Mine is now the nation's largest silver producer. Other large scale mining projects are now on the drawing board, including development of the Kensington Mine and reopening the Alaska-Juneau Mine, which could become North America's largest underground gold mine. The region's mining industry includes more than these large scale projects, however. For example, a significant level of mineral exploration occurs each summer in Southeast Alaska. In addition, mining operations in British Columbia and Yukon Territory are generating jobs and income in Southeast Alaska.

Jan 1, 1992

By L. R. Willmott

An ethanolamine purification unit for removing carbon dioxide and hydrogen sulfide from Firscher-Tropsch synthesis gas was installed at the Bureau of Mines synthetic liquid fuels demonstration plant at Louisiana, Mo. The unit was a surplus Radford Girbotol unit from the Missouri Ordnance Works modified for a capacity of 90,000 std. cu. ft per hour of synthesis gas at 450 p.s.i.g., operating pressure. The hydrogen sulfide loading of the feed gas was specified at 500 grains per 100 cu. Ft. The unit was designed by the Girdler Corp. and installed by the Koppers Co. Initial operations were conducted far 11 days in May 1951. Thereafter 7 additional runs were made, varying lo duration from 8 to 54 days. The last run was terminated on May 29, 1953, the total time the Plant wars in operation being 219 days.

Jan 1, 1956

By M. R. Geer

American and European practices in cleaning fine coal are strikingly different. The tables, launders, classifiers, and pneumatic devices used in America are seldom employed in Continental Europe, where much of the fine coal is cleaned in feldspar jigs, often supplemented by froth flotation of the extreme fines. This difference in choice of cleaning equipment may be fortuitous, but in large measure can be attributed to a difference in economic factors. Coal being more costly in Europe, there is greater emphasis on efficient cleaning of all sizes, including the extreme fines, and it is common to produce a high-ash middling for "on-site" consumption to avoid any waste of fuel value. The feldspar jig has been found advantageous under these conditions. In the United States fuel coal must be prepared as cheaply as possible, and metallurgical coal must be prepared as efficiently as possible; thus in both branches of preparation practice, any cleaning device that promises greater economy or higher efficiency warrants consideration. The feldspar jig, as employed in Europe, has a much higher unit capacity than the wet table used so extensively here and therefore offers economy in the capital costs of a washery through saving in space. As pointed out by Vissac,4/ the jig operates under automatic control, and therefore can cope with fluctuations in quality of feed. Maintenance costs for a single, large-capacity unit, such as the feldspar jig, would be expected to be lower than those for a battery of low-capacity cleaners. These considerations led the Bureau of Mines to undertake an investigation of the feldspar jig to determine its possible usefulness in this country.

Jan 1, 1958

By Courtney A. Young

Cyanide is a critically important chemical to the mining and metallurgical industry. It has a strong affinity for metals making it favorable as an agent for metal finishing and treatment as well as a lixiviant for metal leaching, particularly gold. These technologies are environmentally sound but, because cyanide is very toxic, safeguards are required to prevent accidental spills and treat effluents before being discharged. Various methods of cyanide remediation by separation and destruction for cyanide management purposes are therefore reviewed. The methods have been broadly categorized as physical, -adsorption. complexation and oxidation methods including photolysis and other advanced-oxidation processes. Reaction mechanisms for these methods are presented throughout this paper, Finally, the methods are compared in regards to their effectiveness in treating various cyanide species: free cyanide, thiocyanate, weak-acid dissociables, and strong-acid dissociables.

Jan 1, 1998

By E. J. Lintner

This paper is one of a series being prepared by the United States Bureau of Mines describing clay mining, crushing and grinding methods, and costs, at various operations throughout the United States. These papers are designed to disseminate technical information regarding methods used. The, cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs may in many instances cause embarrassment to the individual operator as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulation shall ensue. The following report deals specifically with the methods employed by the Evans Pipe Co., Uhrichsville, Tuscarawas County, Ohio. The author wishes to acknowledge the assistance of the following company officials: T. J. Evans, II, president; T. J. Evans III, vice president and general manager; and L. P. Young, general superintendent.

Jan 1, 1936

By D. K. Panda

The behavior of single drops with gas evolution at the interface is of interest because this is one of the important reactions that occur in oxygen steelmaking vessels, where a large amount of iron-carbon drops are dispersed in an oxidizing slag. The carbon dissolved in these drops, reacts with the slag to form CO, which is evolved as a gaseous phase. A room- temperature model was used to study the nature of this type of reaction including the effect of various factors such as viscosity and the presence of surface active impurities. Experiments were done for reacting drops over a wide size range to observe various regimes of behavior. Large single drops were levitated in a counter current flow to produce a sufficiently long residence time to allow the study of the various stages in the reaction. The emphasis of this work was to obtain photographic evidence of a high quality to describe all possible modes of behavior, and so a lot of effort was given to developing and perfecting experimental techniques.

Jan 1, 1994

By Elmer W. Pehrson

The recent establishment of an official price of 64.64 cents per ounce for silver by the President's order of December 21, 1933, has provoked discussion as to the effects of this move on the various metal-mining industries. To assist those of the mineral industry who are interested in this problem, the Bureau of Mines presents the following analysis of basic statistical data concerning; the relation of the silver price to the value of copper ores mined in the United States. The term "copper ore" as used herein includes all ores in which copper is the most abundant base metal paid for. In 1928, this class of ore contributed 98 percent of the total copper output of the United States.

Jan 1, 1934

By Michael K. Watkeys, Charlesworth. E. GUY, Jacobus E. Potgieter, Anhaeusser. Carl R., Roger L. Gibson, Alexander F. M. Kisters

Abstract - Intrusive features of cupriferous noritoids from the deeply eroded Proterozoic granite-gneiss terrane of the Okiep Copper District in South Africa illustrate the emplacement of basic magmas into a mid- to lower-crustal environment. The small, easterly trending intermediate to basic intrusions of the so-called Koperberg Suite display a wide variety of geometries, occurrence and emplacement modes, including dike-, sill- and plug-like bodies. Coeval granulite-facies metamorphism, partial melting and ductile deformation of country rock gneisses during intrusion of the basic magmas led to emplacement and dilation processes of the intrusions which differ significantly from those described for dikes and sills at shallow crustal levels. Regional tectonic stresses are largely negligible due to very low differential stress (?1 - ?3) during deformation and intrusion, which permits emplacement at high angles to the principal compressive stress and which follows favorably inclined structural anisotropies. Dilation of the basic intrusions is largely determined by compositional differences of host rocks and occurs by thermal erosion, i.e., assimilation of wall rock gneisses. Low length-to-width ratios of basic to ultrabasic dikes and predominantly diaper -like outlines of mesocratic bodies are indicative of low viscosity contrasts between the mafic magmas and high-grade metamorphic host-rock gneisses. Buoyancy-controlled ascent of the basic to intermediate intrusions is expressed by a broad compositional zoning of basic bodies with respect to the granite-gneiss stratigraphy. Various intrusion modes within the stratigraphic column of the granite-gneiss sequence reflect a lithological and structural stratification of the seemingly homogeneous granite-gneiss terrane.

Jan 1, 1994

By J. N. Greaves

Investigations were conducted by the U.S. Bureau of Mines to develop flowsheets for the recovery of tungsten and gold from four Alaskan scheelite-bearing ores. Basic gravity concentration and cyanide leach tests were performed on all samples. About 46 pct of the tungsten and 30 pct of the gold from one sample were recovered in a gravity concentrate containing 24 pet W03 (tungstic oxide) and 119 troy ounces per short ton (tr oz/st) Au. Froth flotation of the gravity concentrate resulted in separate tungsten and gold products with grades of 38 pct W03 and 2,720 tr oz/st Au and recoveries of 60 and 97 pet, respectively. Additional gold was recovered from the gravity and flotation tailings by cyanidation. Overall recoveries of tungsten and gold from this sample were 28 and 94 pet, respeetively. A flowsheet with mill design parameters was developed that consisted of (1) free gold and scheelite recovery by gravity methods and froth flotation and (2) fme-grained gold recovery by cyanide leaching of reground gravity and flotation tailings, followed by a carbon-in-pulp (CIP) circuit. Data were developed from the Bond mill work index, gold and tungsten flotation, conventional and high-rate thickening, cyanide leaching, and CIP adsorption tests.

Jan 1, 1989

By Herbert D. Drechsler, James B. Stephenson

"AbstractThe paper identifies the major components of price change which affect the determination of the internal rate of return of a mining project. It illustrates several price indexes which may be used to measure general price increases, identifying techniques which might incorporate them into mine valuation procedures. The ""hurdle rate"" for new investment is discussed.IntroductionDECISIONS regarding the value of an orebody and whether or when to mine an orebody are based on an estimate of the cash flows which would be associated with its exploitation. These pro-forma cash flows represent cash in or out of a possible mineable deposit and include exploration and construction costs, sales revenues, operating expenses, taxes, debt borrowings, interest and debt repayment. It has long been recognized that when combining the cash flows occurring over the life of the mine, dollars received or paid out early have greater value than those received or paid out later. This time value of money has been incorporated into mine evaluation calculations through the use of present-value or discounting techniques. Another factor affecting mine valuation, inflation, is not accounted for by valuation techniques now in use. In recent years, price changes have become more volatile. In the past, price change could easily be ignored when evaluating potential mines. Today, the combination of larger investments and greater price volatility leads to great concern about the effects of price change on mine valuation."

Jan 1, 1977

By F. G. Miller

It is generally accepted that sulfur exists in coal in three forms: (1) pyritic, (2) organic, and (3) sulfate sulfur. Sulfate sulfur usually makes up less than 1% of the total sulfur content. Pyritic and organic sulfur, make up almost all of the total sulfur and occur in varying amounts in different coals and can vary greatly in coal of the same seam Pyritic sulfurs of 20% to 80% of the total sulfur have been reported Other authors have shown that it is not possible to remove the organic sulfur without chemically altering the coal. Chapman and Jones (1) state: "Organic sulfur, unlike pyritic sulfur does not exist as discrete particles, but is intimately associated with the coal structure, and as such it is not possible to remove it or reduce its concentration by physical means." Any success in removing sulfur has come about by removing pyritic sulfur by physical means; therefore, removal of sulfur in the pyritic form is the subject of this investigation. The extent to which any impurities can be removed from a particular coal can be determined by a washability study. Outside of crushing coal, to finer sizes or chemically altering the coal, there are no known methods of changing this inherent washability characteristic. The efficiency of various methods used to remove impurities can be determined by comparison of results produced at a yield to the results as shown by a washability study. In recent years heavy media processes have proven their ability to wash plus 28 mesh coal and nearly produce results shown to be theoretically possible by the washability study. Therefore, it is the objective of this paper to show various methods of treating the finer fractions of the coal, in the hope of developing a process, which can effectively produce in the fine fractions the efficiency of heavy media devices in the coarse.

Jan 1, 1963

By Crystal Poon, Paul Matlashewski, John Morkeh, Kathryn Dorfschmidt, Jose Carvalho, Chad Williams

Rockfall hazards are ubiquitous in mining environments making their control critical for safe mining operations. The complex processes involved in rockfall events necessitate a probabilistic modeling approach with well-calibrated material properties. The controls designed to mitigate rockfall hazards need to be reliable, efficient, and safe to deploy to meet the constraints present at an active mine. This paper presents an innovative solution to rockfall at Rio Tinto’s Bingham Canyon Mine. The solution incorporates the site-specific calibration and creation of a predictive rockfall model with the design, field testing, implementation, and monitoring of the rockfall controls.

By W. A. Jones

THE estimation of the average value of gold ore involves many considerations, among them the correct sampling of the deposit, the dilution by waste, and the loss of high-grade fines. It is a common experience that, after all these factors have been evaluated, adjustment of the assays is necessary before satisfactory agreement between the calculated mine grade and the mill heads is obtained. In fact, at many mines the latter correction overshadows all others in the preparation of routine estimates. For this reason it is proposed to deal only with the mathematical treatment of mine assays and the problem of bringing estimates into conformity with the corrected mill heads. Mine assays differ from physical measurements because the range of values is very great and these are not symmetrically distributed above and below the average, there being fewer high than low results. There is no widely accepted mathematical procedure for determining the average of series of measurements which exhibit these characteristics. Customary practice consists in empirically reducing high assays until a satisfactory agreement with mill heads is reached. It was thought that more confidence could be placed in grade estimates if a logical basis for calculations could be devised .. In an attempt to find a fundamentally sound procedure, amenable to practical application, many series of assays comprising over 235,000 channel samples (1) were studied at Hollinger Consolidated Gold Mines, Limited. Such an investigation could only be made where records covering many years of operation are available and where tabulating and calculating machines are in use. The results are recorded in the hope that the relationships noted for the large groups of assays used are of fundamental character and that the data will be useful to others dealing with the problem of grade estimation.

Jan 1, 1943

By Thomas J. Albin

This U.S. Bureau of Mines report identifies potential causes of slip-and-fall accidents occurring during surface mine equipment maintenance and describes the relative roles of direct worker behavior and machine design. The relative roles of human behavior and machine design in the causation of slip-and-fall accidents were determined through analysis of accident records, observations of maintenance worker behavior, and evaluation of mine machinery. From these data, relative risk ratios were calculated. Behavior had a relative risk ratio of 1.5; machine design, specifically access systems design, had a relative risk ratio of 2.2. Of the access systems, ladders had the highest relative risk ratio, 7.0. This study suggests that accident intervention would be most profitably made in improving the design of systems used to access maintenance worker areas of mining equipment.

Jan 1, 1990

By A. G. Yapo, T. W. Camm

"All-in sustaining cost is a metric used by mining companies to reflect the cost of gold mining in a consistent format useful to both investors and mining professionals. Cost reporting focused on the direct cost of mining and processing ore was summarized in the non-GAAP cash cost developed by the Gold Institute in 1996. In 2013, a group of mining companies, working with the World Gold Council, developed a more inclusive approach to reporting costs designed to solve the dilemma of showing a more comprehensive reflection of recurring costs involved in producing gold, without discouraging investors. INTRODUCTION Mining today plays a key role in the development of our civilization as a source of essential raw material and provider of essential fuels, producer of jobs, and a factor in support of the international balance of monetary payment (Camm, 2014). Professionals in mining locate, develop, design and manage ore deposits in an environmentally safe and profitable manner. As mineral deposits become increasingly scarce, new challenges face the industry. A current trend is to an increased emphasis on underground mining techniques for deeper deposits. Operations are safer today than before as companies understand better their work environment and the importance of mining responsibly. A continual challenge for the industry is accurately reflecting the costs and selling price of ore. An enduring characteristic of mining is the situation where the market typically determines the price of a commodity; the main control a company has on the bottom line is to control the cost of production. An attempt to bring light and clarity on the cost of their business will give a better idea to investors on the true profitability of the mining business. Gold producers face this struggle to accurately reflect the cost of production while also seeking to attract the interest of the investment community (Hill, 2013). In order to have a consistent format to report on their production costs, leading gold producers through their alliance inside the World Gold Council (WGC), worked on the adoption of a new cost framework: the All-in Sustaining Cost (AISC) and All-in Cost (AIC). Since 1996, the traditional cash cost reporting has focused only on the mining and processing costs incurred in mining an ounce of gold, which included the costs of goods sold (labor, energy, and consumables costs) and royalties (Table 1). But cash cost reporting ignores many important aspects, like sustaining capital, general and administrative expenses, and site rehabilitation at the end of the mine life (Whelan, 2013). The cash cost was used to attract many investors into the business. In fact the high gross margin (sales minus cash costs) has been promoted the past decades by the industry instead of the net or operating margin. As a result, even when the gold price was high, nearly $1900 per ounce in August 2011, gold producers were not reporting excessive profits in their cash flow / income statements, to the disappointment and incomprehension of investors (Milstead, 2014). The truth was simply that the other costs omitted in the traditional cash cost were reducing the apparent profits."

Jan 1, 2017

By W. R. McClelland

GOLD-BEARING ores, representing many types, are found widely distributed through the Province of British Columbia. They range from those which by their nature may be considered as complex, to those whose mineral characteristics are simple. Those in which the gold is associated with metallic sulphides provide particular milling and metallurgical problems, the solution of which involves not only detailed laboratory investigation but also a careful consideration of economic factors. The location of an ore-body may have a deciding influence on the adoption of a method for the metallurgical treatment. Whether the ore should be treated with the object of recovering the gold as bullion or as a shipping concentrate is often dependent on such topographical considerations as the position of the mine at or near tidewater or within a reasonable overland distance of a smelter. British Columbia is fortunate in having the Trail smelter situated in the southern part of the Province, and the smelter at Tacoma, Washington, is accessible for coastwise traffic. Both of these provide a ready market for most types of gold-bearing concentrate. In order that the results obtained by laboratory tests may give a fair indication of what should follow in mill operation, it is essential that the test sample should represent as closely as possible in mineralogical character and in grade the ore that eventually will constitute the feed to the mill. In the early stages of mine development this consideration is sometimes overlooked and samples of a much higher grade than would be representative of run-of-mine ore are submitted. Flotation tests on such a sample of ore high in sulphides may show a low ratio of concentration, bu.t if the actual run-of-mine ore is lower in sulphides the mill operation will reveal a much higher ratio. The recommendations for treatment based on the results of laboratory tests may have been against concentration, when in actual operation this would be the most suitable method of treatment. Recommendations based on laboratory tests are necessarily from the results of work carried out on the sample submitted, modified only by such other economic or topographical information as may be known to the investigator. This paper deals with a few of the gold ores found in the six mining districts of British Columbia and is based on investigations made in the Ore Dressing and Metallurgical Laboratories of the Mines Branch, Department of Mines, Ottawa.

Jan 1, 1937

By W. G. Jewitt

THE Box mine, situated in Saskatchewan on the north shore of lake Athabasca, is unique in two respects. It is the first and, so far, the only gold mine in Saskatchewan, and it is the only gold mine in Canada to employ a large-scale forced caving system as the main mining method. Discovered in 1934 by Tom Box, an Edmonton prospector, its subsequent history, while breaking no records for speed, has been one of steady and more or less normal development. Camp and plant are situated close to the shore of Beaverlodge bay, sorne 50 miles east of the Saskatchewan-Alberta boundary and 35 miles south of the north boundary of the Province. The railhead at Waterways, Alberta, is about 220 miles to the southwest. Prince Albert lies some 450 miles to the south. The surrounding country presents a rather rugged variation of the usual Precambrian topography, with hills rising five to six hundred feet above lake Athabasca. The numerous lakes and islands, together with the wide expanse of lake Athabasca, compose an attractive scene, at least in the not over-long 'open water' season. The winters are long but not extremely cold, judged by prairie standards. The small lakes break-up around May 20th and the 'freeze-up' stops navigation early in October. Though apparently remote, the Box mine is fortunate in having reason-ably cheap transportation from Edmonton. The 300-mile railway from Edmonton to Waterways is the most expensive section, the rate for 1st class freight being $1.70 per hundred pounds and for 5th class freight $0.77 per hundred. Freight from Waterways to the mine, approximately 140 miles down the Athabasca river and 90 miles along lake Athabasca, is delivered by barges and tugs for 50 cents per hundred pounds. All freight is delivered during the 'open water' shipping season, which lasts from about .Tune 7th to October 7th. In normal years, barges are loaded to 3 to 3 1/2feet draught up to September 1st. After that date, and earlier in dry years, shallow water at Waterways reduces the barge loads. Barges of 100 to 200 tons capacity handle all mining freight, including pieces up to 15 tons in weight, without undue difficulty.

Jan 1, 1940

By D. Harrington

Insofar as prevention of mine explosions is concerned, it is apparent that the coal-mining industry has profited but little from experiences during the past 15 years. The fact that explosions can be prevented if well-known preventive measures are adopted and conscientiously carried out appears to warrant the conclusion that many coal-mining people are indifferent to the hazards that may result in explosions. Although the principal burden of preventing explosions is upon the management, and much of the evident carelessness in failing to place in effect and to enforce suitable precautions, is assessable directly against management, the worker also has a very definite responsibility, and numerous explosions have resulted because of his failure to carry out his part in accepted principles of safety. The record of fatalities from mine explosions during the past 5 fiscal years has been anything but encouraging or about which coal-mining people can take pride; more men were killed by explosions (673) than were killed from the same cause during the preceding eight years combined (577). During each of the fiscal years 1942 and 1943, 152 fatalities resulted from explosions, compared to 163 during the fiscal year 1941, 206 in 1940, and only 16 in 1939.

Jan 1, 1944

By J. W. Meier, J. O. Edwards, R. C. Bell

"IntroductionTHE DIE CASTING industry .as we know it today is the direct result of the invention and development of die casting machines during the nineteenth century and of reliable alloys in the twentieth. The early machines were designed to cast low melting point metals such as lead .and tin, and their alloys.It was inevitable that, as these die castings were put into service, the demand should arise for stronger materials. Zinc alloys, often containing lead, tin, copper, and aluminum as major constituents, were relatively easy to cast and stronger than the lead and tin alloys. However, it became apparent after a number of years that these zinc alloys tended to become brittle, distort, and corrode, particularly if kept in warm, humid atmospheres. Thus, considerable quantities of zinc-base .alloys were in use before the trouble was realized and effective measures could .be taken to determine the cause of the instability.The deleterious effect of certain metallic impurities on the properties of zinc •die casting .alloys has now been known for about thirty years. Brauer .and Peirce, and, later, other research workers of the New Jersey Zinc Company such as Anderson and Werley, discovered the pronouned effect of lead, cadmium, and tin on the stability of zinc-alloys."

Jan 1, 1952