Search Documents

By E. E. Ungar

The ways in which noise is generated and radiated by chutes and screens are described and corresponding noise control concepts are discussed. The amounts of noise reduction produced by applicable noise control means are delineated and generally cost-effective means are recommended. Available noise control materials and their applications are discussed. The results of field measurements, laboratory experiments, theoretical analyses, and studies of data provided by suppliers are summarized.

Jan 1, 1975

By Henry M. Howe

PART I. § 1. Introduction. After giving certain definitions, this paper gives the reasons which led to Roozeboom's form of the diagram of the freezing-point curves and general equilibrium of the iron-carbon compounds, steel and cast-iron ; and then those which led to replacing it with the present or double diagram, in which graphite is at all temperatures held to be the more stable and cementite the less stable (metastable) form of carbon. Next in § 10 the evidence supporting this greater stability of graphite is examined, then in § 17 that which seems to oppose it, and in § 22 a summary of the evidence is presented. The second part of the paper considers the topography of the graphite-iron diagram, rejecting summarily the solubility-lines based on the data of Charpy and Grenet and of Mannes-mann, on the ground that the data even on their face do not really point toward these lines, and that they are wholly incompetent to determine any solubility-lines whatsoever, because they report together with the dissolved carbon also an indeterminate quantity of cement-carbon, and because even such carbon as is actually dissolved, only in part represents the solubility of graphite, and in another and indeterminate part represents the solubility of cementite, or at least of carbon in presence of cementite as distinguished from graphite. It might be thought that graphite is but slightly soluble in iron, because of the absence of any suggestions of eutectoid graphite, corresponding to the eutectoid cementite of pearlite in very many cases in which the cast-iron seems to consist of ferrite and massive graphite only, and because of the micrographs of Goerens and Gutowsky. In these the primary austenite of cast-iron quenched but little below the eutectic freezing-

Jan 7, 1908

By R. H. Fernald

In 1900, as far as available records show, there were only two producer-gas power installations in the United States. In June, 1915, the number probably exceeded 1,000. Of this number, some 84.5 per cent comprised small plants using anthracite, and only about 15 per cent of the total number utilized bituminous coal and lignite. In addition to these, two plants used wood, and three or four used oil. In the main, however, the larger sized units are operating on bituminous coal and lignite. During the early years of these plants little success was anticipated from the use of bituminous coals and lignites, but in 1904 and 1905 it was fully demonstrated at the Government testing station at St. Louis that these fuels could be utilized to excellent advantage. However, although many producer-gas plants in daily operation are using bituminous coal and lignite, many power-plant men are still skeptical regarding the successful commercial use of these fuels.

Jan 1, 1916

By G. E. McElroy

The Coeur d'Alene minim, district of Shoshone County, Idaho, has been one of the largest and most active lead-silver producing districts in the United States for the last 40 years. The mines of the district enjoy exceptional natural advantages with respect to ventilation in that the veins apex high on mountain sides and are most often developed to considerable depths, up to 2,000 feet, by adit and crosscut tunnels under conditions that develop large natural draft pressures; the increase of temperature of the rock with increase of depth from surface in at a low rate; and the average surface temperatures are low. These natural conditions have, in the main, resulted in well-ventilated mines with low temperature conditions throughout. However, where the development has been carried to considerable depths below the lowest level of surface entry, natural-draft ventilation has proved inadequate, and mechanical ventilation systems have been installed on the three largest mines of the district. Local conditions, more particularly those in dead-ended working places, have also required auxiliary ventilation by will fan-pipe units in these and other mines. A particular feature of the district is the number of exceptionally long crosscut tunnels that have been driven to provide entry to vein systems from low points adjacent to milling and transporta¬tion facilities. Three of these tunnels are approximately 2 miles long, and lengths of 3,000 to 8,000 feet are quite common.

Jan 1, 1931

By W. H. Frederic, F. H. Gibson, R. F. Abernethy

This publication contains the quantitative values for phosphorus , chlorine , sodium , and potassium in United States coals . The samples tested were taken from commercial shipments and have been selected to represent the principal coal producing areas of the country . Due to combining the analytical results from two separate surveys , values for the four elements are not available for all samples .

Jan 1, 1965

By H. D. Hess, C. P. Mabie

This report describes in detail the results of petrographic research conducted on 21 phosphate ores representing important deposits in southwestern Montana , southeastern Idaho , and northeastern Utah . The ores are described and categorized by mineralogical and chemical composition , thermal behavior of organic carbon , and textural constitution . Descriptive and genetic classification schemes applicable to western phosphate ores are discussed ; results from related studies made of the collophane mineralogy are also presented . The latter studies were centered on determining unit - cell dimensions and CO₂ , P2O5 , and fluorine content of collophane concentrates of 11 high - grade phosphate- rock hand specimens selected solely for this purpose . On the basis of this investigation , operational methods have been developed for quantitatively describing textural and compositional features that are likely to be significant in determining the response of phosphate ores to conventional beneficiation treatments ; systems for classifying the ores in relation to these features have been proposed . Studies to date point out distinct textural and compositional variations in the western phosphates and illustrate their importance in determining optimum beneficiation procedure .

Jan 1, 1964

By Arthur E. Bruszak, Marcel Vanpée

In many practical combustion systems ignition may occur through contact with hot burned gases . Such a process plays a vital role in flame stabilization on bluff bodies . It is also of importance in the ignition of firedamp by the hot spent gases of explosives used in mines . Also , in the communication of flames through narrow channels , a problem of practical importance in flameproofing electrical equipment , the propagation of the flame is essentially a reignition process in which hot burned gases are the agent of ignition . In the actual ignition problem a great variety of conditions may be visualized . Ignition may occur where pockets of hot gases are surrounded by cold explosive mixtures or where pockets of cold mixture may be surrounded by hot gases . Alternately , a flowing stream of combustible mixture may be initially in contact with another stream of hot combustion products , or a jet of hot gases may flow into a cold quiescent mixture ; the jet may be laminar or turbulent , continuous or discontinuous . The hot gas may also consist of the oxidant ( air for instance ) and the cold combustible pure fuel . This study by the Bureau of Mines is concerned only with ignition produced by a continuous jet of gas ( hot ) flowing into a practically quiescent cold mix- The investigation of ignition by bursts of hot gases or by turbulent jets is outside the scope of this report , and work performed on this phase of the problem has been published elsewhere

Jan 1, 1963

By Monika Patrycja Polak - Micewicz

This paper presents an approach for estimating the fatigue life for the base of powered roof supports (shield) manufactured by the FAZOS roof support company. FAZOS?s powered roof supports are designed to operate on an inclined coal seam in full caving with a medium, strong roof strength. This shield support is utilized in conjunction with a shearer and face conveyor for a complete longwall mining system. To design shield support, it is essential for contractor to know the physical (hardness, toughness, etc.) and mechanical properties of material (tensile strength, Young?s modulus, etc.) used for the shield support as well as the geotechnical properties of the mine site. The fatigue strength of the shield support material depends on the mean stress, alternating stress, cycle frequency, transport dimensions, mine environment and other factors. In order to estimate the fatigue life for a powered roof support system, it is assumed in this paper that the support must keep the roof stable in the mine under variable load cycles. The approach selected in this study contains Goodman?s model (Goodman, 1899) for all blocks in the design housing which is subjected to sinusoidal load. On this basis, the degree of fatigue damage was calculated and compared to the results of experimental tests. It will be shown that there is a significant detrimental effect on the fatigue life of the base of the powered roof supports due to geometrical notches. The Ramberg-Osgood model and damage accumulation rule (Palmgren-Miner) (Miner M., 1945) were used and numerical analyses were conducted, utilizing ANSYS finite element software. These analyses play a very important role in longwall casing design. The proposed method allows assessment of the yield state and forecast of the structure cracking, taking plastic strains occurrence into account. The presented method is universal and can be applied for fatigue life estimation of other subassemblies of powered roof supports. The final portion of the paper presents results of variable amplitude loading simulations on the S355N and S690Q steel used to make powered roof supports. The results of the physical tests were compared with the results from finite element methods. The proposed approach to calculate fatigue life gives the best correlation between the experimental results and calculated values of fatigue life for the powered roof support base. Finally, the design process uses a simple approach to predict fatigue life in a short time, reducing design costs and providing longer service life for roof supports.

Jan 1, 2012

By A. C. Fieldner

"Gas hazards may be divided into two principal classes- namely (1) inflammation and explosions; (2) asphyxiation and poisoning. Inflammation and explosion are prevented first by adequate ventilation so that gas sufficient to propagate flame or explosion can not accumulate, and second, by avoiding sources of ignition such as open lights, flames, sparks, electrical arcs, short circuits, or sparks. Ventilation is also the best preventive measure against asphyxiation and poisoning from toxic gases. When men must enter unventilated or poorly ventilated places containing poisonous or asphyxiating gases, suitable gas masks, hose masks, or oxygen breathing apparatus should be worn. As a rule, loss of life and property from gas hazards is due to ignorance of the properties and hazards of various gases commonly used, and consequently a failure to use proper measures for eliminating and meeting these dangers. It is the purpose of this paper to describe briefly the common gases and vapors with respect to the hazards involved in their use and to discuss the necessary precautions and methods for avoiding these dangersLight, heat, and power are prime essentials of our modern industrial civilization. The combustible gases and vapors used for the production of these necessary elements of our existence comprise the largest and most common group of domestic and industrial gas hazards. Almost every individual in his daily life subject to possible danger from asphyxiation, fire, or explosion due to one or more of these gases. For evidence one need only refer to the daily newspaper where headlines such as the following are frequently seen; ""Family asphyxiated by carbon monoxide from gas heater;"" ""Schoolhouse wrecked by gas explosion in basement;"" ""Man killed by automobile exhaust fumes in his garage;"" ""Fireman overcome by smoke fumes in basement ""Woman"".""Boman severely burned by accidental ignition of gasoline used in cleaning gloves;"" and 'in recent Years we often see ""Building wrecked by explosion of still in residential district.""It will be noted that these accidents are due to inflammation, explosion, or asphyxiation. Any combustible gas or vapor, when mixed, with air or oxygen within certain limiting proportions, will explode on ignition. The violence of the explosion varies with respective proportions of air and gas, and with the degree of confinement of the mixture. For example: Mixtures of natural gas and air containing between 4.5 and 12 per cent natural gas will explode, or propagate flame throughout the mixture without the continual presence of the source of ignition that started the inflammation. The table following gives the explosive limits of the common combustible gases and air:"

Jun 1, 1926

By B Hayter, M Carr, K Williams, C Wheeler, W Chen

Current trends into mining iron ore have seen an increase in the exploitation of problematic orebodies that would typically be disregarded. These bulk materials cause problems within all facets of the material handling stream, from remains left in train wagons to transfer chute blockages, which can cause costly downtime to mining operations (Roberts, 1998). These problematic bulk materials are referred to as wet and sticky material (WSM) due to the adhesive and cohesive nature they possess. Their characteristics can be computationally expensive to model. With the development of discrete element modelling (DEM), in conjunction with advancement in computational power over the past decade, it is now more feasible to model WSMs into the DEM technique.This research will couple two different contact models that can represent the characteristics of a WSM. These models include the Simplified Johnson-Kendall-Roberts (SJKR) and the Easo liquid bridging contact models. The SJKR contact model is an expanded form of the classic Hertz model. This model includes the tensile forces that are in the contact zone between two bodies when they are separated, which the Hertz model failed to capture (Johnson, Kendall and Roberts, 1971). The Easo liquid bridging contact model accounts for the capillary effects and surface tension that will form between two bodies, such as that of a WSM (Soulié et al, 2006). Both of these models were coupled to give the best representation of a WSM, which was simulated using MoleculeX™ (Chen and Williams, 2017) as the software platform.Additionally, this research also investigated the adhesion of problematic iron ore samples onto impact plates under dynamic conditions. An experimental set-up consisting of an apron feeder and inclined impact plate was utilised, to gain an understanding of the way the material builds-up and the possible modes of failure that could be experienced. This was undertaken for different wall liner materials, wall liner angles and moisture contents of the iron ore samples. From this, a series of DEM calibration simulations were conducted on the experimental set-up and particle size distributions (PSD) of the iron ore samples. This enabled forming of a database of parameters, which can be scaled for on-site applications in relation to geometry of the plant and PSDs that would represent run-of-mine ores.CITATION:Carr, M, Williams, K, Chen, W, Hayter, B, Roberts, A and Wheeler, C, 2017. The dynamic adhesion of wet and sticky iron ores onto impact plates, in Proceedings Iron Ore 2017, pp 511–518 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Goutam H. Shahani

Today, the mining and mineral sectors are being impacted by highly fluctuating supply ? demand, extreme price volatility and tremendous market uncertainty on a world-wide basis. This pattern is expected to continue for the foreseeable future. In particular, large consumers of tonnage quantities of industrial gases (oxygen, nitrogen) all have to make informed investment decisions in this uncertain economic environment. Plant owners ? operators need to carefully examine their current and future industrial gas needs in order to develop the most cost-effective industrial gas plant configuration. This can be done by partnering with an experienced engineering company that offers a complete technology portfolio for producing industrial gases. Ideally, the mineral and engineering companies have to work together as a single team to identify the most efficient and economic plant design. This includes an in-depth assessment of capital and operating costs, in order to deliver an optimal solution, taking plant reliability and process safety into account. It is important to consider all the industrial gas needs at a given manufacturing complex, in conjunction with available utilities and infrastructure to develop the best possible long term solution. Oxygen (O2) requirements include: oxygen enriched and oxy-fuel combustion, smelting and hydrometallurgical operations. Nitrogen (N2) is used for annealing. All of these industrial gas requirements have to be examined at a given site over a long term horizon in a holistic manner. Cryogenic air separation was first practiced at a commercial scale in 1902. Since then, the technology has been constantly refined to reduce cost; and improve reliability and flexibility. Today, using advanced engineering techniques, including proprietary process simulation, and modern fabrication techniques, it is possible to build air separation plants that are both low cost and high quality at the same time. It is important to work with an engineering company that owns a complete portfolio of industrial gas technologies, functional engineering capabilities and a variety of plant solutions. Such a partnership can quickly identify a ?sweet spot? for a given situation. By drawing on experience gained from hundreds of projects, it is possible to quickly optimize a given requirement. In situations where a customer wants a complete solution it may be appropriate to provide an air separation plant on a turn-key basis. This will enable the mining and mineral processor to focus on their core business. By using global procurement and construction capabilities it is possible reduce cost and improve project execution, thereby making industrial gas plant procurement simpler and cheaper for the mining and mineral sector.

Nov 1, 2011

By Douglas D. Donald

The New Jersey Zinc Co. successfully holed through a 2 1/2-mile haulage tunnel connecting its new Ivanhoe shaft with the Van Mater Shaft at Austinville, Va. This 8x 10-ft cross-section tunnel was driven from both ends and met at a point approximately a mile from one shaft and a mile and a half from the other. In order to make certain that the faces met accurately on line and grade it was necessary to refine conventional mine surveying practices. The mines that are serviced by these shafts are located in the southwestern part of Virginia approximately midway between Roanoke and Bristol at the west foot of the Blue Ridge. While the presence of lead-zinc sulfide ores has been known in this area for more than 200 years, it was in 1902 that New Jersey Zinc Co. acquired the Austinville property, which has been in constant operation since that time. About ten years ago the company undertook an extensive diamond drilling program at Ivanhoe several miles to the southwest. This program was successful in locating sufficient ore to justify the purchase of a number of the properties in this area and plans were made to develop the new orebodies. The discovery of this ore as well as substantial addi- tional reserves at Austinville resulted in a decision by the company to increase its daily milling capacity to 3000 tons, of which about 1000 tons would be supplied from the Ivanhoe mine. After careful consideration of all possible methods of transporting this volume of ore from Ivanhoe to the mill, it became evident that diesel locomotive haulage through a 2½-mile tunnel between the two mines would best suit prevailing conditions. Since the lowest operating level, known as the 1100 level, of each mine would be at approximately the same elevation, it was obvious that such a tunnel should be driven on this level. Not only would this tunnel facilitate feeding Ivanhoe ore into the underground crusher and skip loading installation at Austinville, but it would also open up a known orebody 5000 ft southwest of the Van Mater shaft. In addition it would provide a valuable diamond drilling base from which a large and a potentially favorable but untested block of ground might be explored. In order to hasten the completion of the tunnel, it was felt that it should be driven from both ends. ENGINEERING CONTROL PROCEDURES It was vital that the tunnel junction be made accurately on line and grade; thus it was felt that engineering control of an unusually high degree of reliability was required to prevent an accumulation

Jan 1, 1959

By Gunhild Hennum, Tewodros Tefera, Gisle Håland, Annette Jahr

"Abstract The Gudrun field is located west of Stavanger in the North Sea at water depth of 109 m. A jacket substructure was selected to support the topside and was installed in 2011. The jacket shall be able to support 16 of 0.762 m (30 in) diameter conductors and is equipped with a drilling deck to allow for pre-drilling by a jack-up rig through the jacket. In general the soil conditions below mudline comprise of a thin top layer of very loose to dense sand overlaying several layers of sandy clay, ranging in stiffness from firm to hard. Below some 30 m depth the soil consists of layers of medium dense to dense silty sand overlaying very hard sandy clay containing thick beds of sand to 100 m depth or more below mudline. The jacket is secured to the seabed by twelve 2.438 m (96 in) diameter steel pipe piles, three at each pile cluster located at the four legs of the jacket at sea floor. Different design methods were used to determine the pile penetration depth. Pile drivability was evaluated using best estimate and upper bound soil parameters. The pile driving and blow count record show that the target penetration was reached as predicted. This paper discusses the different methods used to determine the pile capacity, target penetration depth and the drivability analyses made for the Gudrun jacket piles. The soil resistance during pile driving is back-calculated from the pile installation data and compared with the prediction made.IntroductionThe Gudrun platform is located west of Stavanger in the North Sea at water depth of 109 m. A jacket substructure was selected for the Gudrun platform. The general Gudrun platform jacket configuration is to a large extent dictated by the topside layout, the requirements for support points enclosing the well slots and access for the jack-up rig. The Gudrun platform jacket is a traditional 4 legged structure with a vertical side towards the jack-up rig. At the seabed the jacket is quadratic with a base dimension of 40 by 40 metres. Figure 1 shows the Gudrun jacket during load-out from the fabrication yard to the transport barge. At the site the jacket was lifted off the barge, upended and placed on the seabed by the installation vessel. The jacket is secured to the seabed by twelve 96"" (2.438 m) diameter steel pipe piles, three at each pile cluster located at the four legs of the jacket at sea floor. The target penetration of the piles is 47 m."

Jan 1, 2014

By T. Banerjee, D. Felsher, G. Leavoy

"Lake Shore Gold is engaged in commercial gold production at both the Timmins West and Bell Creek mines, located in Timmins, Ontario. Run of mine ore is processed at the Bell Creek mill which consists of a conventional gold mill flow sheet involving crushing, grinding, gravity concentration and carbon-in-leach (CIL) for gold recovery. Since 2009, the operating capacity of the mill has been upgraded from 2000 tpd tonnes per day (tpd) to over 3,000 tpd. The most recent expansion involved the installation of a low aspect ratio SAG mill to replace the secondary crusher. Without operational data on the low aspect mill, combined with a site team that was new to SAG milling, there were many challenges in achieving the target throughput from the circuit. Through the implementation of AwaRE advanced controllers, running in closed loop with PRC fragmentation cameras as well as embedded PARC modules within the Allen Bradley PLC, the site was able to rapidly develop a best operating practise and has been successful in creating a stable and consistent operational environment. The process, lessons learned and eventual solution will be reviewed in this paper.INTRODUCTIONLake Shore Gold is engaged in commercial gold production at both the Timmins West and Bell Creek mines, located in Timmins, Ontario. Run of mine ore is processed at the Bell Creek mill which consists of a conventional gold mill flow sheet involving crushing, grinding, gravity concentration and carbon-in-leach (CIL) for gold recovery. Since 2009, the operating capacity of the mill has been upgraded from 2,000 tpd tonnes per day (tpd) to 3,150 tpd. The most recent expansion involved the installation of a low aspect ratio SAG mill to replace the secondary crusher. This endeavor was split into two phases: the expansion of the back-end (Phase 1) and the front-end (Phase 2) of the mill. Phase 1 of the expansion was completed at the end of 2012 and involved enhancements and capacity addition to the leaching and adsorption circuits, which increased the mill’s capacity to 2,500 tpd. Phase 2 of the expansion commenced at the end of July 2013 and involved the expansion of the crushing and grinding circuits. The expanded front-end of the mill now has a capacity of 5,500 tpd, and processes ore from both Bell Creek and Timmins West mines. The updated flow-sheet, as shown in Figure 1, illustrates the replacement of the two-stage crushing and ball milling circuit with a single stage crusher and a low aspect ratio SAG mill."

Jan 1, 2015

By A Kurniawan, A Sjadat and M Akhasyah

PT Freeport Indonesia’s Deep Ore Zone (DOZ) is a block cave mining operation that has been in production for 15 years. DOZ is located approximately 900 m below surface and has an average production rate of more than 5000 t/d. The footprint of the extraction level will ultimately be 900 m long and average more than 200 m wide. The undercut level is located 20 m above the extraction level.While developing Panel 1K on the northern portion of the extraction level, a major geotechnical problem was encountered when there was a change in lithology and an associated fault intersection. A large collapse of the hanging wall of the extraction level drifts occurred in the area of the fault intersection between February and March 2011. This was followed by a collapse of one of the undercut level drifts directly above the extraction level in May 2011.It was suggested that the best approach to mitigate risk during rehabilitation was to systematically open up the failed area under the protection of a steel set support system. To achieve this, approximately 60 t of grout was injected from the undercut level to fill the voids created when the rock mass between the two levels failed. A ground penetrating radar system was used to survey the condition of the rock mass between the two levels before and after the injection of grout. After the grout injection phase was completed to a satisfactory level of confidence, rehabilitation activities started on the extraction level by taking out the now consolidated material from inside the drift in 2 m advances from under steel sets initially constructed in secured ground.Controlled blasting was the key aspect to the success of the initiative to open up just enough of the drift to systematically support the rock mass before the next set was installed. The systematic support consisted of in-cycle shotcrete sprayed over mesh pinned to the exposed rock, as effectively as possible, with splitsets before spiling the next advance’s protection canopy with rebar. Once secure, a combination of steel set and pumped concrete was installed as the final support. This final support provided a safe platform to repeat the process until the failed zone was safely traversed.CITATION:Kurniawan, A, Sjadat, A and Akhasyah, M, 2016. Rehabilitation of the collapsed panel 1K north in the Deep Ore Zone block cave mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 763–768 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By L. B. Slichter

Prospecting is certainly the world's biggest and best gambling business. It is a game where the chips cost many thousands and where many millions, even billions, can be won. An attractive feature of this gamble is the fact that the players are free to rig the odds as favorably as possible. Only the limited bounty of nature, the restrictions of the laws of the land, the competition from other players, the limited sagacity of the player himself— only these, and other factors, restrict the possibilities for large winnings. Today probably about half the land surface of the earth remains to be searched for signs of ore visible at the surface. It is fortunate that so much land still remains for exploration by relatively economical methods. Looking to the future, it is a good guess that the costs of finding ore will increase in response to increasing technical difficulties. To continue to achieve profits from prospecting, it will become necessary to analyze the business more skillfully, in a more and more sophisticated manner. Whenever feasible, qualitative concepts must be replaced by their quantitative equivalents, improvements, and extensions. THE GAMBLE The fact that prospecting is a gambling business reminds us at once of the elementary rule known as the law of gambler's ruin. I hesitate to mention so simple a rule in this company of experts. This rule expresses the rather serious chance of going broke when the odds for success are small, merely by a normal run of bad luck regardless of the long-run expectations of gain. The only sure way of avoiding this special risk of gambler's ruin is to have enough capital, and the will, to continue the play many times and thus ride out the inevitable runs of bad luck. For example, if the probability of success is one in ten for each venture, there is a 35 pct chance that ten successive ventures will fail in a row. But if one has the capital to continue the play through a run of 100 failures, then the chance of gambler's ruin is only 5 in 100,000. Almost any management, I suppose, would be under terrific pressure to cease the play during a long run of bad luck. To continue to prospect under such circumstances requires great confidence in the premises, and a firm conviction in the long-term expectation of profit. There is evidence which I shall mention that in the future even the strongest companies may not have the necessary capital to prospect on the ideal scale. Joint ventures will be very desirable as a means for extending the available venture

Jan 1, 1961

By J. P. Germiquet

"Rock properties have a material impact on mining processes, including drilling performance. An investigation using point loaded index (PLI) data converted to uniaxial compressive strength (UCS) has revealed that a direct relationship between grain size and UCS exists at Mogalakwena Mine. This correlation is best seen in unaltered rock, with lower correlations for altered rock types. Measurements from the new RockMa system installed on drill rigs can be used to obtain rock strength data to validate the current rock strength domains and create additional data for the next benches below. An investigation of penetration rates in different lithologies shows that rock composition plays an important role in determining drill performance. Additionally, there is an inverse relationship between rock strength and drilling penetration rate – a measure of how efficiently a hole is drilled.The domaining of grain-size-adjusted UCS at Mogalakwena Mine will allow more accurate scheduling of drill rigs through increased knowledge of rock strength in various areas. Successful rock strength domaining has the potential to be incorporated into blast indexing and predicting crushing/milling performance.IntroductionThe optimization of mining and processing through geometallurgical characterization of ore are key drivers of value realization (Deutch, 2013). Rock strength is one such property and is affected by, among other variables, composition, texture, and grain size (Ozturk, Nasuf, and Kahraman, 2014). Mogalakwena Mine is exploiting the intrusive Platreef PGE (platinum group element)-bearing orebody which forms part of the northern limb of the Bushveld Complex. This complex orebody exhibits areas of metasomatic alteration, metamorphism, and sporadic mineralization of the footwall and hangingwall (Nex et al., 2006). Understanding this variability is paramount due to the implications for rock strength and hardness, which in turn affect crushing, milling, and liberation efficiency. These variables must be known prior to blasting in order to optimize mine and plant processes using in-situ variables. This necessitates predictive modelling (Deutch, 2013). Geological and geotechnical data was sourced from the Overysel (OY) exploration database for the study. Point load testing was done for each borehole and the results converted to uniaxial compressive strength (UCS) (Akram and Bakar, 2007). The relationship of lithology, texture, and grain size with UCS revealed an inverse relationship between grain size and UCS in unaltered rock. The relationship was not present in altered rock types. A comparison of mean strength and hardness results indicated that Bond work index and UCS may be related. Drilling performance is affected by UCS (Bourgoyne et al., 1986), and this was proven using recent measurements obtained during drilling. Lastly, grain-sizeadjusted UCS values were applied to a 3D model for the OY property."

Jan 1, 2016

By R. L. Caldwell, E. E. Glenn, L. J. Norton, A. J. D. Straus, S. V. Holcomb, J. Zemanek

A new and unique logging tool, called the Borehole Televiewer (BHTV), has been developed to inspect boreholes and to evaluate formations. Even though geologists and engineers have had only about 3 years' experience with the BHTV, the thinking of many of them has been radically influenced by the fascinating and revealing "log-picture" recorded with the tool. The BHTV fills a need for a logging tool that can produce a direct and descriptive record of the physical properties of the borehole environment. Although primarily developed to evaluate fractured reservoirs, the BHTV has been used successfully to solve a variety of problems related to formation evaluation and borehole inspection. Geologists and petroleum engineers have been confounded for many years by the problems of locating and evaluating fractures. Interpretation of the usual resistivity, acoustic or radioactivity logs, as well as the analysis of cores, for evaluation of fractured reservoirs is extremely difficult and often not definitive. This is understandable since analysis of cores from fractured formations has reported variously: (a) low porosity, (b) no effective permeability, (c) lack of any matrix oil saturation and (d) oil stains on fracture planes as the only indications of potential production.14 In recent years acoustic amplitude logs have been introduced and used with varying degrees of success to locate fractures.8'9'11"13 Conventional amplitude logs at best give only qualitative answers where quantitative ones are desired. The logs reveal nothing of the orientation of the fractures. In addition to these logs, various types of cameras, television, and rubber impression packers have been used for borehole inspection. (See Appendix.) The BHTV logging tool supplies both the quantitative and the orientation answers about fractures. The borehole can be filled with any homogeneous, gas-free liquid such as fresh water, saturated brine, crude oil or drilling muds. This tool takes an "acoustic picture" of the borehole wall. The resulting log is a representation of the borehole wall as if it were split vertically and laid flat. The log is oriented with respect to magnetic north. Any physical changes in the borehole wall are seen as changes in picture intensity. In this way, fractures, deformation or pits are reflected on the log. Tool Description The fundamental parts of the BHTV are shown in Fig. 1. A piezoelectric transducer probes the borehole wall with bursts of acoustic energy. A flux-gate magnetometer senses the earth's magnetic field and provides the means for determining the orientation of the log. A motor rotates the transducer and mag-

Jan 1, 1970

By W. Barnett

The Limpopo Metamorphic Belt is a complex geological terrane with at least three major deformational events. Tectonically juxtaposed lithology, open to isoclinal folding, crosscutting and re-activated shear zones and metamorphic gneisses and schists make pit slope design and maintenance a risky business. Venetia diamond mine?s Cut 3 is planned to reach 360 m by 2011. The difficult rockmass created problems in the original pit and a new more comprehensive slope design was necessary. Nearly 9 km of geotechnical drilling were undertaken to produce a new geological model and provide geotechnical information near the final Cut 3 face. All existing data from the pit were brought together into a database. SRK Consulting were brought into the project to audit the process and provide most of the manpower for the data analysis. Existing failures were back-analysed and the geotechnical domains identified. Analyses of only the southern domains are discussed in this paper. Geotechnical engineers can design slopes at any angle, but it is up to the managers at the mine to decide what risk they are willing to accept in a slope design. Once the issue of risk was discussed and settled in respect of the consequences of failure, each of the main geotechnical domains were analysed to produce a slope design at5% probability of failure with 15% above the first ramp. A risk assessment of the design was then undertaken to determine what risk the design placed on the equipment, personnel and the profitability of the overall mining operation. The risk assessment indicated minimal risk to the operation. One of the main assumptions of the final design is that the pit slopes will be dewatered. A project was immediately put in place to determine a groundwater model for the mine and to thereby determine the best dewatering procedure. However, it should be obvious that it is practically impossible to prevent benches from getting briefly saturated with water during storm conditions. It was therefore necessary to look specifically at supporting the crests of the ramps in the problematic southern domains to guard against the possibility of crest failure during heavy rains. The data available were re-analysed toward this objective. Spiles were recommended as the most cost-effective support system, and a probabilistic approach was used in the design. The final design has a 5% probability of failure, and the analyses indicate a strong sensitivity of the required spile spacing to the strength of the reinforcement material that will eventually be used. The pit slope parameters derived as per the discussion in this paper have just begun to be implemented at Venetia Mine.

Jan 1, 2001

By G. W. Jones

"INTRODUCTION In a previous reports results were given of a manhole investigation carried out over a period from June,- 1929, to July, 1930, in cooperation with the Edison Electric Illuminating Co. of Boston, Mass., to determine the general hazards of combustible gases and vapors in manholes and other underground openings owned by this company. Considerable time was spent in this initial investigation in developing a suitable detector for determining the range of explosibility of the gases found in manholes. About 17,000 tests have been made with the detector since the investigation was started and its utility has been verified and its accuracy checked, by having complete analyses made of such samples that showed combustibles present equal to or above 25 per cent of the lower explosive limit, and those found deficient in oxygen.The initial investigation made in 1929 and 1930 demonstrated that the detection, control, and elimination of combustible hazards in manholes can best be obtained by a close cooperation of the interested parties through a systematic and continuous inspection of manholes, under proper supervision.COOPERATIVE INVESTIGATI0N DURING 1931The investigation carried out during the year 1931 has been along lines similar to that conducted during 1929 and 1930. In the present investigation the Edison Electric Illuminating Cc. of Boston and the Boston Consolidated Gas Co., have cooperated with the Bureau of lanes. The Boston Consolidated Gas Co. serves a major part of the territory under discussion with gas, but the tests covered the Edison territory irrespective of the gam company furnishing manufactured gas. A test crew consisting of two men, one an employee of the Consolidated Gas Co. and one an employee of the Edison Electric Illuminating Co., has been continuously employed during the year in the testing of games in manholes served by the Edison system. The test crew was under the direct supervision of John Campbell, superintendent of the special service department of the Edison Electric Illuminating Co., and F. M. Goodwin vice president of the Consolidated Gas Co.As in the previous investigation, all manhole tests were given test numbers. The test data sheets on which the information regarding the tests were recorded were prepared in triplicate, one copy going to the Edison Company, one going to the Gas company, and the third to the Bureau of Mines at Pittsburgh. These test data sheets were then filed (1) according to the town, (2) the street location, and (3) the manhole number; in this way a complete record pf each manhole tested was immediately available. A specimen test sheet is given below."

Sep 1, 1932